Search Documents

By D. S. Choi

This paper describes an improved source location technique for microseismic events related to coal mining. A system of non- linear distance equations is solved with the use of the Newton-Raphson method. This computational method is- advantageous when the number of geophones is limited. In addition, this paper includes the results of the analysis of data from several instruments which characterize both mine seismicity and environmental noise such as vehicle traffic. Analysis of the mine seismicity has contributed to a better understanding of caving above a longwall gob and of what constitutes stable ground conditions.

Jan 1, 1990

By Daniel W. Su

This paper presents the results of a detailed geotechnical study on the potential multiple seam interaction between the No. 2 Gas (upper) and the Powellton seams, which are separated by an average interburden of 45 ft. The interburden consists of 4 ft of clay shale below the No. 2 Gas seam, 38 ft of massive sandstone, and 3 ft of shale above the Powellton seam. The No. 2 Gas seam was mined about 60 years ago, and many water-pooled areas were projected to be present. The deepest overburden over the No. 2 Gas seam is about 750 ft. To evaluate the potential interaction between the two mine works and to determine the pillar safety factor, Analysis of Multiple Seam Stability (AMSS) software was initially used to determine pillar dimensions to obtain a minimum safety factor of 2.0 for areas under pooled water, as well as a minimum safety factor of 1.5 for areas not under pooled water. Furthermore, to assess the quality of the interburden rock strata, two surface core holes were drilled, and rock cores were tested in the laboratory for their strength and elastic moduli. Using the experimentally determined strengths and moduli as part of the input parameters, the RocScience Phase2 finite element program was employed to model the stress field scenarios and estimate the safety factors of the interburden rock strata before and after Powellton seam mining. The pillar safety factors derived from the Phase2 analysis were in excellent agreement with those obtained from the AMSS analysis. Phase2 results also predicted that the effect of the Powellton seam mining, first mining only, would reach a maximum of 19 ft above the Powellton seam, which led to the proposal of drilling 25-ft deep test holes to detect water, instead of the 45-ft deep test holes mandated by MSHA. The proposed test-hole height was accepted by both Mine Safety and Health Administration (MSHA) District 4 and the state of West Virginia. Mining of the Powellton coal seam commenced in February 2011 and continued for eight months. To date, no 25-ft deep hole has encountered water under the water-pooled zone, which validates the RocScience Phase2 finite element analysis. Also, inmine observation of excellent pillar stability and roof condition confirms the validity of the AMSS analysis.

Jan 1, 2012

By A. Wahab Khair

Coal mining has evolved into extensive use of continuous mining machines for development and production. This has resulted in an increase in dependence on the versatile continuous miners. The present-day continuous miners are powerful in terms of rated power but are still plagued by wear of bits which hinders development and production as the bits have to be continuously changed at regular intervals. Previous attempts to analyze bit wear has been either restricted to the theoretical approach and or laboratory testing. This paper discusses about the overall aspect of bit and drum design for different conditions. Using the laboratory model set up, numerical models and field testing, a new bit and drum design was analyzed to evaluate their performance under different conditions. The results proved that a newer bit design and drum design were successful in limiting the amount of wear as well as improving the performance of the continuous miner and production.

Jan 1, 2008

By Victor V. Nazimko

Long term stability of the pillars that have been remained after R&P extraction causes postponed subsidence. To prevent unforeseen subsidence and to diminish postponed subsidence 25-50% new method for its control has been developed by the author. It supposes to use drilling and blasting technology and other original approaches. New method has been fulfilled through the holes being drilled from the surface or from the active underground openings. Explosives had been charged into the holes and were blasted. This had increased bulking factor dramatically and prevented natural caving of the strata. Physical scale modeling corroborated efficiency of the new approach. The bulking factor has grown from 0.0623 to 0.1185 and surface subsidence has been diminished from 1.1 m to 0.2 m or 5.5 times.

Jan 1, 1996

By Gabriel Esterhuizen

The room-and-pillar mining method is used extensively in underground limestone mines in the Eastern and Midwestern U.S. The rock mass is typically a near-horizontal, bedded deposit at relatively shallow depth. A survey of 34 mines was conducted in which data on roof spans, rock mass properties and support practices were collected as part of a National Institute for Occupational Safety and Health research project into ground control in limestone mines. The average room width is 13.5 m (44 ft), accommodating large mechanized equipment. The results show that the immediate roof beam can consist of many individual layers and can contain several near-vertical joints. In spite of the room widths, the roof is naturally stable in many mines. Observed roof instabilities can generally be related to excessive horizontal stresses or unfavorable geological structures that cause block fallout or beam failure of the bedded roof rocks. The survey showed that the rock mass quality of the limestone does not vary significantly throughout the Eastern and Midwestern U.S. Roof conditions and the need for support were found to be closely related to the thickness and competence of the first layer of limestone in the roof. The findings highlight the need to identify local geological structures and the roof beam characteristics so that support alternatives can be evaluated. Monitoring and observational technologies that are available for identifying potentially unstable roof are presented, which include: roof characterization using the Rock Fall Risk Index, automated logging of roofbolt hole drilling, microseismic monitoring and displacement monitoring.

Jan 1, 2007

By Hani Mitri

Understanding the interaction between rock bolts and underground rock movement is critical for safe and cost effective underground excavation design. Although early research on this subject involved a balance of theoretical analysis and field measurement, recent work has been heavily focused on analytical and numerical studies. This paper describes technologies that have the potential to redress the balance through instrumentation of rock bolts deployed under routine operating conditions in underground mines. Two new products are presented in this paper. Firstly the U-cell coupler is a load cell device that can be routinely coupled to the threaded end of a bolt prior to installation. It measures the ?series? load at the head of the bolt. Secondly, the d-REBAR involves an array of small-diameter, long-base length displacement sensors recessed into grooves along the entire length of the bolt. Both new instruments are interfaced with on-board digital signal conditioning and telemetry. Methodologies for the deployment of the new instrumentation and guidelines are presented for the interpretation of results based on data obtained from field trials. Successful field installations demonstrate the viability and practicality of these new technologies and, moreover, provide important insight in to rock bolt/rock mass interaction.

Jan 1, 2012

By Meagan S. Boltz

From October 2000 to April 2001 a local array of fourteen seismograph stations was deployed at the Trail Mountain Mine (TMM), an underground coal mine in Emery County, Utah, to locate mining-induced seismicity (MIS). Original analysis of the data provided epicentral locations that coincided closely with the active longwall panel. The original analysis yielded poor quality hypocenters, however, preventing a useful relation from being made between mining activity and the event depths. For the original analysis, only stations at elevations above mine level were used for locating MIS. As a result, P- and S-arrival times from four of the stations in the local array were not used: an inmine station and three stations at elevations below mine level. This study compares mine workings and active mining to a revised TMM dataset that included P- and S-arrival times from the lower elevation stations that were not used in the previous study. In the revised locations, a modified master event methodology was used to calculate station delays. These station delays correct for errors in the shallow layers of the velocity model. The resulting hypocentral locations have improved depth resolution, determined by a lower root mean square (RMS) for the locations, compared to the original study. Most of the events occur in the roof of the mine and follow the longwall panel. When located using the velocity model determined in the original study, the elevations of the events increase as the longwall panel progresses. One possible explanation for the elevation increase is that it may be related to geology or the caving process. As presented here, a 10% decrease in the shallow velocity structure results in a more plausible location for the hypocenters. Consequently, it is hypothesized that progressive development of the TMM longwall panel(s) may have resulted in a progressive change in the velocity model.

Jan 1, 2012

By G. J. Hasenfus

Although theoretical and conceptual knowledge regarding the impact of horizontal stress on underground coal mining excavations have existed since at least the mid-1900s, it wasn?t until the late 1970?s that the theory and practical understanding began to mesh. Since that time, particularly over the last 25 years of this Conference, increased empirical study, as well as advances in measurement technology, computer simulation, and bolt design, has significantly improved our understanding of horizontal stress impact, and provided coal mine operators with tools to reliably predict and manage it. This paper provides a retrospective review of some of the more important horizontal stress-related advancements made during the 25 years of Conference proceedings, particularly those for predicting and controlling horizontal stress impacts within underground coal mines. Relevant and significant CONSOL experiences and studies will be presented in context, with particular attention to horizontal stress considerations for longwall faces and gateroads. The significance of horizontal stress will also be placed in context with respect to local geology and structure, ground support measures, and mining configuration, method, and sequence.

Jan 1, 2006

By Archie Richardson

The trona mines in the Green River Basin, commonly known as the "trona patch," present an interesting set of rock mechanics issues stemming from mining in a unique underground environment. Like other minerals occurring in tabular deposits, trona is mined using high-productivity room-and-pillar and longwall methods. However, trona does not behave quite like other evaporites and behaves far differently than coal. In this paper, the following key issues in trona patch rock mechanics are discussed: material properties, in situ stress field, water and gas pressure effects, creep characteristics, pillar behavior, roof span stability, floor stability, underground tailings storage, longwall mining, two-seam mining. and solution mining. Many of the existing trona producers are entering potentially more difficult mining conditions, and much consideration is being given to "new" technologies such as longwall mining and solution mining. In analyzing 20 years of experience with trona patch rock mechanics issues the authors have identified key comparisons and contrasts with conventional tabular deposit rock mechanics that will help illuminate what has been learned as the trona patch enters the 21" century.

Jan 1, 1999

By Xu Lin Sheng

During the mining course, when the roof above coal seams is constituted by thick and hard sandstone (conglomerate), sudden roof movements often take place with great force and de¬struction which is the biggest danger to the safety and production. Such sever movements of the roof in mining directly relate to the rock mechanical properties which are the main fac¬tors that influences the regularity of hard roof movement and its destruction form. A significient work and important technical way for applying rock mechanics into mining en¬gineering is studying the rock mechanics of the hard roof and altering some of the rock me¬chanic parameters which induce the improvement of the rock properties in order to efficiently control the movement of the hard roof.

Jan 1, 1989

By B. Arjang

ABSTRACT: Ground stresses are one of the significant factors in the context of rockbursts and underground instability at some hard rock mines in Canada. Overcoring strain relief measurements using triaxiaI strain eel is were performed at depths between 60 to 1890 m at several mine sites to provide stress data for stability analysis and optimum mine design. Pre-mining ground stress determinations from 64 stress tensor analyses resulted in the following average stress gradients: Maximum horizontal stress. -Hmax - 8.18 - 0.0122 MPa/m depth Minimum horizontal stress. _-,,min - 3.64 - 0.0276 MPa/m depth Average horizontal stress. -11, 5.91 - 0.03-19 MPs m depth Vertical stress. '-, - 0.0266 - 0.008 MPa/m depth The maximum and minimum horizontal compressive stresses. with an average ratio of 1.75 ,0..45. prevail in east--west and northerly directions. respectively. Horizontal compressive stresses in excess of vertical overburden load were determined. indicating large variations in ratios to a depth of about 1000 m with decreasing trend towards depth. From present data. a particular regional zoning for the magnitude and direction of horizontal stress fields cannot be outlined. A common feature at mines with near vertical orebodies is that the maximum horizontal compressive stress acts perpendicular to strike while the minimum horizontal compressive stress is aligned on-strike. The vertical stress components approach the gravitational overburden load.

Jan 1, 1989

By Ulrich Paschedag

The WESTFALIA group of companies developer and manufactures underground mining machinery for complete high-performance longwalls. WESTFALIA uses a state of the art electrohydraulic system as the most important component for the realisation of today's fully automated plow or shearer longwall. The shield control unit (SCU) allows maximum custom designed software flexiblity as well as maximum hardware reliability. The master control unit (MCU) monitors shield support data as well as the plow/shearer position. By using an industry standard PC in an explosion-proof box with an intransically safe keyboard nearly unlimited software capabilities can be obtained with inexpensive hardware. Among various other modes of operation this MCU allows the monitoring and recording of data which can be transmitted to a surface computer. Production and operational adjustments can be made by the mine management based on the MCU information. Statistical analysis of the distribution of roof pressure under various conditions is also possible. The WESTFALIA automation system PM-4 gives the operator maximum flexibility and helps the mine management to run their longwall more efficiently and safely.

Jan 1, 1994

By Christopher Mark

Multiple seam interactions are a major ground control hazard in many U.S. underground coal mines. The two most common types are: ? Undermining, where stress concentrations caused by previous full extraction in an overlying seam is the primary concern, and; ? Overmining, where previous full extraction in an underlying seam can result in stress concentrations and rock damage from subsidence. The National Institute for Occupational Safety and Health (NIOSH) has completed a major study aimed at helping to identify the location and likely severity of these interactions. In the course of field visits to mines throughout the U.S., more than 300 multiple seam case histories were assembled into the largest data base of multiple seam case histories ever collected. These data were analyzed with the multivariate statistical technique of logistic regression. The study also employed LaM2D to estimate the multiple seam stresses, ALPS and ARMPS to determine pillar stability factors, and the CMRR to measure roof quality. The study resulted in the development of a computer program, called Analysis of Multiple Seam Stability (AMSS), which can help mine planners to evaluate each potential interaction and take steps to reduce the risk of ground control failure. AMSS first evaluates pillar design by calculating the single seam Stability Factor (SFSS) using ALPS or ARMPS. It also automatically generates a LaM2D analysis that provides the additional multiple seam stress so that the final, multiple seam SFMS can be determined. The second part of the AMSS procedure builds upon the statistical findings that overmining is much more difficult than undermining, isolated remnant pillars cause more problems than gob-solid boundaries, and weaker roof significantly increases the risk of multiple seam interactions. AMSS quantifies these effects and predicts the outcome in terms of three levels of risk: GREEN (where a major multiple seam interaction is considered unlikely), YELLOW (where adding a pattern of cable bolts or other equivalent supplemental support could greatly reduce the probability of a major interaction.), or RED (a major interaction should be considered likely, and it may be desirable to avoid the area entirely).

Jan 1, 2007

By Nan Hua

As a high production and high efficient mining method, top coal caving method is now widely used in China. However, as more extra-thick coal seams are mined, it becomes more and more difficult to make the top coal fully broken up, resulting in more and more top coals flowing into the gob, rather than onto the rear AFC at the working face as designed. This research is aimed to investigate the failure mechanisms of the extra-thick top coal caving mining method.

Jan 1, 2009

By Axel Preusse

For the last 150 years, subsidence damage to the surface has been an unavoidable phenomenon associated with underground coal mining. In particular, the mechanization of mining methods in multiple seam mining and the concentration of mining activities in densely populated European metropolitan areas (e.g., Ruhr, Upper Silesian industrial region) have led to mining having a very strong influence on the earth?s surface. In both these regions, surface subsidence of more than 20m has been reported up to now in comparison to the original state. Underground coal mining in these regions strongly impairs all kinds of surface use, such as urban and industrial development, infrastructure (roads, waterways, and railways) and pipelines?without restricting the functionality of those objects to a greater extent. Demanding and, in some cases, globally unique engineering solutions have been developed and implemented for this purpose. The previously mentioned mining and industrial regions are still very strongly characterized by the (increasingly declining) coal industry and will remain dependent to a large extent and for an indefinite period on artificial drainage measures because subsidence that has already occurred is irreversible. This paper will primarily discuss the prediction of subsidence that is caused by intensive multiple seam mining and its influence on surface objects (e.g., underground pipelines). However, an approach for predicting ground uplifts due to rising mine water as a consequence of mine closures will also be described.

Jan 1, 2012

By David F. Gearhart

The Burrell Can1 is a thin, steel, tubular shell filled with aerated concrete that is used as a roof support in coal mines. The Can height is always shorter than the mining entry, so it is capped with wooden timbers and wedges when it is installed. This combination of the Can and the wooden header is a standing support system that is designed to yield in a controlled manner and exhibit a constant yield, or elastic-plastic behavior. The Burrell Can is capable of withstanding 20 in or more of vertical convergence and 15 in or more of horizontal displacement. Because of this exceptional ability to sustain load through extended convergence and displacement, it is one of the most robust standing supports in use today. The National Institute for Occupational Safety and Health (NIOSH) conducted testing on seventeen Burrell Cans in 1995, during development of the support where the ratio of the height to the diameter, or the aspect ratio, was between 2:1 and 4:1. Based on the results of that testing, it was suggested that the standard aspect ratio of the Can be less than 5:1. This suggestion is intended to preserve the overall stability of the Can, which will help to maintain the initial stiffness and prevent load shedding. Recently, the necessity of the aspect ratio has been questioned, and this issue will be addressed in this paper. Since the initial development and introduction, more than 130 tests of the Can have been conducted at the NIOSH Mine Roof Simulator (MRS), and 25 of those specimens had aspect ratios greater than 5:1. The 18-in-diameter by 10-ft-tall specimens had the largest aspect ratio, 6.67:1.However, the aspect ratio is not the only parameter that affects the performance characteristics of the Can. Multiple factors, such as the use of different wood species, the use of different header or footer configurations, and the use of pedestals, as well as biaxial loading conditions can also decrease the stiffness and capacity of the Can. Data from full-scale tests that include these other factors are analyzed to show that the initial stiffness is primarily affected by the roof and floor contact configurations. Furthermore, load shedding is more likely to occur or begin earlier when the aspect ratio is greater than 5:1 and one or more of the other factors are present.

Jan 1, 2012

By W. C. Lacy

Stratabound copper ore bodies in thick Proterozoic metamorphosed sedimentary and volcanic rocks at the Tong Kuang Yu Mine in southern Shanxi Province of China were considered as possibly being amenable to block cave mining. Initial evaluation of caving characteristics was based upon old calyx drilling records, limited underground mining experience and geological mapping, a few diamond drill holes and measurements in surface subsidence features. Classification and mapping distribution of rock quality types aided in mine design, prediction of fragment sizing and explosive requirements, cave assist and ground support requirements. Comparison is made between early feasibility predictions and actual mine experience.

Jan 1, 1989

By Robert G. Harris

During the last five years there have been significant improvements in face support monitoring techniques particularly in respect of face pressure. The measurement of support loading pressures was originally conceived as a maintenance aid for the hydraulic systems but recent work has also included geological loading displays of the complete face as well as individual supports. This paper briefly examines the means of obtaining this information, together with some examples of actual face data. Also included is a summary of the benefits of such monitoring and an outline of future development work.

Jan 1, 1993

By Dae S. Young

A new probabilistic approach is introduced for slope stability analysis including adverse impact of blasting vibrations. The material strength within a slope area is randomized in this bi-variate joint probability analysis. To be a completely general engineering method, the new probabilistic approach employs the random variable transformation technique; the Hermite model of the Gaussian transformation function, which transforms the experimental histogram of strength values to the standard Gaussian variables. Because bi-normal joint probability is analyzed on the true probability region projected on the Gaussian transformed variable plane, it is an exact solution of slope stability based on the available sample data. Details of the probabilistic approach are given through a case study on an iron ore mine. The case study demonstrated that the probabilistic approach is effective and simple enough to be a routine engineering practice for slope analysis.

Jan 1, 1984

By Gabriel S. Esterhuizen

A survey of pillar conditions was carried out at 21 operating limestone mines that use the room-and-pillar method. The surveyed pillars were all located in rock that was classified as ?Good? to ?Very Good? using the RMR rock mass classification system. The average pillar width was 14.5m and the width to height ratio varied between 0.53 and 3.52. Pillar conditions were rated using a visual rating system that accounts for the effect of geological structures as well as stress related fracturing. Nine cases of pillar instability were recorded. Pillar instabilities were typically limited to individual pillars or small groups of pillars within an otherwise stable layout. Local geological structures such as inclined discontinuities or weak bedding planes contributed to instability in seven of nine cases that were observed. Elevated pillar stresses contributed to instability in the two remaining cases. All the unstable pillars observed had width-to-height ratios of less than 1.5. It is concluded that pillar instability is most likely to be caused by unfavorable geological structures in pillars with width to height ratios of less than 1.5. Stress related instability such as rib spalling becomes more prevalent when the average pillar stress approaches approximately 20 MPa.

Jan 1, 2006