Search Documents

By Raymond Sandiford, Taehyun Moon

"In 2012, Superstorm Sandy (Sandy) caused extensive flooding in many of the tunnels in New York City. The inundation resulted in two distinct stress changes to the tunnel structures. The first stress change was water pressure on the inside face of the tunnel lining. The second condition related to the change in buoyancy of the tunnels. In areas where the tunnels were supported on rock and an adjoining area supported on soft soil, overstress issues arose. Numerical analyses were performed to assess the structural impacts of the tunnel water inundation; especially stress changes due to internal pressure as well as changes resulting from the buoyancy effects. The paper will discuss the assessment process and its results; it will demonstrate that the change in internal pressure were of little consequence, however the change in buoyancy resulted in significant increases in bolt stresses. INTRODUCTION Superstorm Sandy caused tens of billions of dollars in damage in the NYC metropolitan area. It also caused significant disruption to the transportation system by flooding most of the under river tunnels servicing Manhattan from the outer boroughs and New Jersey. The rehabilitation of the tunnels was of paramount importance to the restoration of the NY and NJ economies. With this rapid restoration, it was essential to determine whether the flooding of these tunnels caused damage to tunnel structures. A series of analyses were undertaken to ascertain whether the change in the stress conditions and buoyancy of the tunnels, due to the flooding, was significant enough to cause damage or over-stressing of the tunnel components. The effects of this unforeseen loading condition was a concern to the agencies operating these tunnels and were thus analyzed to ascertain if there were any adverse impacts. This was a concern because the majority of under river tunnels in NYC was built earlier in the century and constructed using bolted cast-iron lining segments. The cast iron, although quite strong in compression, is much less so in tension. Also, after nearly a century of use, the bolts connecting these segments together have under gone varying degrees of corrosion. The stress changes in both the liner segments and the supporting bolts were estimated for conservative ground support conditions to provide confidence that the flooding had not caused permanent damage."

Jan 1, 2016

By C. Heckman, M. S. Moats, A. Luyima, W. Cui

"Nucleation and growth of copper on 316L stainless steel from synthetic acidified copper sulfate was studied in the absence and presence of chloride ions and/or organic additives – HydroStar® 4208, DXG-F7® and Cyquest® N-900 – using a potentiostatic technique. The current–time data obtained at 0.16V versus the SHE were analyzed using nucleation and growth models. Scanning electron microscope (SEM) images of deposits produced at 300 A/m2 show that the addition of 20 mg/L chloride ions increased the size and reduced the number of copper nuclei. Potentiostatic current–time data from the electrolyte without organic additives, and confirmed by SEM images, indicate progressive nucleation with two-dimensional growth under diffusion control. None of the organic additives studied at a concentration of 2.5 mg/L with 20 mg/L chloride changed the nucleation and growth mechanism, but the additives increased the number and reduced the size of copper nuclei, leading to more uniform coverage of the stainless steel substrate.IntroductionElectrowinning of copper is an important process in the manufacture of high-purity copper metal. Approximately 20 percent of the world’s refined copper is produced from acidified copper sulfate solutions by electrowinning (Schlesinger, Sole and Davenport, 2011). In many plants, copper is electrodeposited on AISI 316L stainless steel substrates for a period of 6-7 days, after which the copper is stripped from the blanks. Even though the deposition time for a commercial copper electrowinning circuit is around one week, it is critically important to control the nucleation, growth and nature of the initial deposit (Sun and O’Keefe, 1992).Deposit morphology and structure are influenced by the real current density at the electrode surface. The real current density across the cathode surface is made uniform by proper design of the electrowinning cell and electrodes and careful operational practice. Even with good design and control, some current maldistribution occurs. The outcome of severe current maldistribution is poor deposits that affect product quality and/or increase energy consumption. To combat current maldistribution and create a larger operating window in terms of current density, temperature and copper concentration, small amounts of organic smoothing agents – traditionally, guar products – are added to copper electrowinning electrolytes. Moreover, these additives inhibit the growth of copper nodules and lead to improved deposit quality by producing bright, smooth and dense cathodes.Recently, the use of polysaccharides, such as HydroStar 4208 and DXG-F7, and polyacrylamides, such as Cyquest N-900, has been reported in commercial electrowinning tankhouses as replacements for guar (Ashford, Clayton and Sandoval, 2012; Robinson et al., 2013; Sandoval, Morales and Bernu, 2010). However, little information has been published on the effect of these new organic additives, especially regarding the nucleation and growth mechanisms of copper electrodeposits in their presence."

Jan 1, 2016

By Geoffrey Purcell

Improvements which have been made in commericial flotation systems during the past fifty years have resulted more from trial and error methods in the mill than from research in the laboratory. Research has often provided explanations of why mill changes have improved the metallurgical process. Hopefully, in the next fifty years, changes in mill flowsheets will come about, primarily, as a result of research work. However, since minerals, in their infinite variety, cannot be reduced to a standard state, research on commercial ores will have only a local utility, and research on pure minerals will have little commercial application. What will emerge from research on pure systems are mechanisms of adsorption, and this in turn may throw some light on the very much more complex adsorption processes taking place in the pulps of commercial ores. Quartz, without a doubt, has been the subject of more research effort than any other mineral, but we are still a long way from completely understanding its behavior in flo¬tation. Hematite and calcite have received considerably less attention. Ores containing a mixture of all three minerals, however, are commercially important, and the iron deposits in Alabama have been extensively studied by the United States Bureau of Mines (1). The literature reveals no reports of research on synthetic mixtures of all three.

Jan 1, 1967

By Joyce A. Ober

Minerals for electronic and optical uses divide easily into two sections: 1) quartz and 2) minerals other than quartz. QUARTZ The properties of quartz crystal that make it useful for radio communications were discovered in 1918. Since that time, an in¬dustry for the mining and processing of natural quartz crystal has grown, matured, and been almost entirely replaced by new tech¬nology. The new technology still involves quartz crystal, but ma¬terial that is grown rather than mined. An economic summary of the commercial growing of quartz crystals has a place in a handbook directed to the mineral engi¬neering industry because quartz crystals have long been an impor¬tant commercial mineral, and the raw material for cultured quartz - ¬that is to say, quartz crystals grown through the ingenuity of man - is still natural quartz. Nearly all the natural crystals that have been used for elec¬tronics and optics came from Brazil. The larger pieces which met rigorous standards of quality were used for electronic and, to a lesser extent, optical components. Smaller pieces and fragments were used for vitreous silica. The need for high quality material in quantity led to US government sponsored research and exploration programs in the 1940s. No deposits meeting the very rigid requirements for electronic-grade quartz were found, but other projects resulted in the development of a process for the factory growth of beautiful crystals of prescribed shape, size, and quality. Domestic deposits of appropriate quality were identified to use as raw materials for the quartz culturing process. The development of the cultured quartz crystal illustrates the success that technology can have in adapting a product of the mine to increasingly sophisticated uses. A remarkable achievement per¬haps, but foreshadowed by experiments by Giorgio Spezia (1908), an Italian geologist studying the relative effects of temperature and alkaline environment on the solubility of quartz. Modem radio equipment is most often controlled as to fre¬quency by the presence in the circuit of a separately added crystal¬ - the 1918 discovery responsible for the existence and growth of the quartz industry. The crystal is quartz, but this component is a carefully oriented and prepared slice from a crystal, but not a crystal as recognized by a rock hound or seen in a museum. How quartz operates to control frequencies is not a proper subject for a handbook on industrial minerals, and references should be consulted (Cady, 1964, Mason, 1964). Quartz belongs to a class of materials called dielectrics: those that do not conduct an electric current but permit electric fields to exist and act across them. Quartz shows the piezoelectric effect, which means that when a quartz plate is mechanically deformed against its natural stiffness, one of its surfaces becomes negatively charged, the other positively charged. When the plate is released quickly from the stress, the charges disappear as the plate regains its original shape, but because of mechanical momentum the plate deforms in the opposite direction (to a lesser amount) and the surfaces correspondingly become charged in the opposite direction. By thinly coating the two surfaces with metal and attaching flexible wires, these charges can be brought into an electronic circuit. If the surfaces are suddenly electrically charged by movement of current through the wires, the converse piezoelectric effect occurs and the plate deforms. Carry the thought further and it is realized that an alternating current flowing through the wires responds to the mechanical oscillation. By controlling the thickness of the plate, its mechanical vibration frequency can be varied through a wide range. One type of quartz plate, the AT-cut, has a precisely defined orientation with respect to the crystallographic axes of the crystal and vibrates on a microscopic scale much as a book would deform when placed flat on a table and the top cover moved parallel back and forth with the hand. At least 17 other orientations have been studied, some of which have preferred uses in various applications (Cady, 1964). The quartz crystal industry is composed of three main segments (excluding fused quartz and quartz used for optical purposes): 1. Natural electronic-grade quartz crystals. Mined quartz suitable for fabrication into piezoelectric units. Zlobik (1981a) esti¬mated the waste to ore ratio at 1:1000 to 1000 000, depending upon the deposit. 2. Lasca. Mined quartz usable as feedstock in the production of cultured quartz. Approximately 0.63 kg of lasca are required to produce 0.45 kg of cultured quartz. 3. Cultured quartz. Cultured quartz is produced from lasca feed¬stock in a process of crystal growth in an autoclave under conditions of heat, pressure, and time. It is estimated that 0.45 kg of cultured quartz is equivalent to 1.4 to 4.5 kg of natural quartz crystal in yield of commercial quartz suitable for slicing into piezoelectric units. The chronology of the development of the quartz crystal industry both natural and cultured follows: Date Comment 1918 Discovery of the piezoelectric effects of quartz crystal 1921 Application of the piezoelectric effects of quartz crystal in the circuitry of radios 1948 Establishment of a quartz crystal commodity stockpile by the US Government 1952 US consumption of natural quartz crystal at an all time high of 228 t 1958 First commercial production of cultured quartz crystal 1970 Cultured quartz crystal production exceeds imports of nat¬ural quartz crystal 1971 Cultured quartz crystal consumption surpasses natural quartz crystal consumption

Jan 1, 1994

By P. Somasundaran

The use of chemical additives in ultrafine grinding will be reviewed in this paper for the case of grinding of quartz in solutions of surfactants and inorganic electrolytes including some dispersants under different conditions of pH and ionic strength. Mechanisms are examined by correlating the grinding effects with those obtained for the influence of these chemicals on zeta potential, pulp fluidity and flocculation/dispersion characteristics. The analysis suggests grinding depends mainly on the state of aggregation of the ground products in- side the mill and the pulp fluidity. Implications of the observed effects on ultrafine grinding in general are discussed.

Jan 1, 1983

By Bruce C. Trent

In order to effectively model subsidence caused by underground openings, a two-dimensional computer code has been developed which couples near- and far-field response. The near-field is simulated by a discrete element block code and a finite difference code represents the continuum region in the far-field. The explicit equations allow rapid and inexpensive solutions to geometries which may lead to subsidence. Two sample problems are presented which illustrate the important features of the code.

Jan 1, 1979

By C. D. Mann

INTRODUCTION The sublevel stoping mining method is usually applied to a relatively steeply dipping, competent ore body, surrounded by competent wall rock. Ore is produced by drilling and blasting longholes, which can range from 50 mm (2 in.) to 200 mm (7% in.) diam, with lengths up to 90 m (300 ft). Longholes can be inclined in any direction, but the ring or pattern usually forms a plane, and the holes are blasted as a unit. Recently developed mobile drilling and loading machinery, as well as new explosives products, blasting techniques, and cemented sand and rock fill have made sublevel stoping a highly efficient and versatile mining method. When designing a sublevel stoping production sys- tem, it should be kept in mind that production rates from conventional sublevel stopes vary widely through- out the life of the stope. Early production is at a low rate, coming only from the drawpoints near the slot, but increases as new drawpoints are reached by the stope face. As the stope nears completion, again, fewer drawpoints are productive. Enough drawpoints must be available at any time to provide required production. Drawpoint availability should be compared to equipment availability; plan for more drawpoints than are needed at any one time. Accurate, realistic scheduling is essential to smooth production rates. Also, initial recovery of ore in a stope/pillar block is normally from 35% to 50% in sublevel stoping. Planning of pillar recovery, representing the majority of ore tonnage in a production block, must be done during early mine planning. Since much of the development already done for primary stoping (access for drilling, drawpoints, and haulageways), can be used for pillar recovery, early production from pillars is highly desirable. The following description of components of the system is an attempt to highlight some of the most important features and requirements of mechanized sublevel stoping methods. Similar comments would apply to the use of older equipment (column-and-arm drill setups, slushers, etc.) in similar methods. As in any good mining system, maximum economic recovery of the resource in the ground is the primary consideration. STOPE DESIGN CHARACTERISTICS Length and Width The following are some of the factors which affect sublevel open stope length and width dimensions: ore body geometry, principal stress directions, competence of stope back, optimum drill pattern, and drilling drift layout. In new mines initial stope layout design may occur before the ore body is actually intersected by mine workings. Stope dimensioning is a critical decision, and assistance from as many knowledgeable people as possible at this stage is essential. Operators with past experience in similar ore bodies, rock mechanics experts, and others with mine design experience should participate at this stage of stope planning. Height The following are some of the factors which must be considered in determining stope height: competence of stope pillar and stope/fill walls; slenderness ratio of adjacent pillars; ore body dip; ore body thickness; hole depth capability of the drilling machine; fragmentation characteristics of the ore; and level intervals in existing mines. In competent ground, drill-hole length and accuracy are the most important determinants of stoping height. Frequently entire drilling sublevels can be eliminated because of the depth capability of sophisticated drilling equipment, resulting in significant development cost savings. Drawpoint Location and Design Some of the most important considerations of a good drawpoint system are optimum spacing of draw- points, within the constraints of stope dimensions, for uniform drawdown and maximum recovery; excavations designed for stability for the life of the ore block to be drawn-primary stope ore as well as subsequent pillar ore; floor or roadway design including type of surface, reinforcing, grade for water runoff; orientation with respect to the main haulageway, for optimum loader maneuverability and ground stability at the inter- section; and length, to allow articulated front-end loaders to work in a straight configuration. Careful drawpoint design and construction are keys to successful production. Extra care in development, such as smooth wall blasting, rockbolts or grouted rebar, wire mesh, and shotcrete usually will ensure long draw- point life. Human exposure during production loading is of longer duration than during development or production drilling, and consequently preparation of draw- points is easily justified, particularly when pillar ore can be drawn through the same drawpoints. Secondary blasting of boulders can weaken drawpoints, also justifying good ground control techniques. A smooth draw- point floor of poured, reinforced concrete, on a grade of +3% or +4% toward the ore pile facilitates water flow out of the drawpoint, and ease of loader bucket penetration into the muck pile. Slot Raising, Slotting A slot or other space for rock expansion is necessary in conventional sublevel stoping where vertical rings or rows of holes are blasted. The slot can be started at a slot raise driven by conventional raising methods, raise boring, drop raising (predrilling and blasting a raise from the top, using small diameter-less than 200-mm (7%-in.)-holes for relief), or crater blasting (similar to drop raising, but without relief holes). The slot usually extends from the extraction level to the back of the stope. It is normally expanded to full stope width by

Jan 1, 1982

By Robert E. Jones

The barite industry shares with its associates in the minerals industry the impediments of excessive federal and state regulations. We have learned to exist with the Organic Act of 1976, the Mine Safety and Health Act of 1966, and the Multiple Use Act of 1955. I do not mean to imply by the above that all aspects of mining legislation have been detrimental, however, each of you has been subjected to interpretative restrictions by federal or state bureaucrats. As frustrating and costly as this is to the barite industry, it is not the primary problem facing our segment of the industry at the present time. Our major difficulty today deals not with too much government regulation, but with the lack of a cohesive and consistent government energy program. This administration and those that have preceded it have dealt with intermittent energy crises on an emergency basis. If we remove the political rhetoric which has surrounded each of the more recent major crises, we can liken the action of our federal government to that of a rural volunteer fire department which devotes its entire efforts toward extinguishing existing fires rather than the developing of programs designed to prevent future fires. The lack of a comprehensive energy program has created an environment in which long range planning is extremely difficult, if not impossible.

Jan 1, 1983

By Robert W. Greene

Next month, American Commercial Barge Line Company will begin moving coal from mines on the old Camp Breckinridge property in Western Kentucky to TVA's new 2600 MW steam plant at Cumberland City, Tennessee. By April of 1973, this movement will reach a level of 7,000,000 tons per year. TVA bought the coal rights to this property from the General Services Administration in 1965 for approximately $7 million. The reserve contains about 120 million tons of recoverable No.9 coal, and about the same recover-able amount of No. 11 coal. TVA then contracted through competitive bidding with Peabody Coal Company to mine the No.9 seam through two slope shafts. The mines are about 300 feet deep and are separated by the one major fault on this property. The mine portals are approximately 3-1/2 miles apart, with the northern portal being over nine miles distant from the Ohio River (see Figure No.1). In 1969 TV A took bids on alternate methods for transporting 120 million tons of coal to Cumberland City at seven million tons per year. These alter-natives included overland transportation to the Ohio River by rail or conveyor, water transportation from Union County, Kentucky to Cumberland City, and total transportation packages from Camp Breckinridge to Cumberland City. The latter could be a joint land/water package, or all land (rail). Ultimately American Commercial Barge Line was awarded an $88 million package transportation contract to convey the coal from Camp Breckinridge to Uniontown, Kentucky; to store it at Uniontown in a quantity sufficient to allow ratable delivery to the steam plant; and to barge from Uniontown to Cumberland City via the Ohio and Cumberland Rivers.

Jan 1, 1971

By Y. Guan

The dissolution behavior of silver and copper from silver/copper alloys in ammoniacal solutions has been investigated using a rotating disc. Oxygen was used as an oxidant. The effect of composition of alloys, concentration of lixiviants, stirring speed and temperature on the overall dissolution kinetics has been studied. Silver / copper alloys of three compositions were used in this study. The atomic percents of silver in these alloys were 76.9, 46.9 and 24.1. The results on the rate of dissolution obtained for these alloys have been compared with that of pure silver and copper under the same testing conditions. A particular emphasis has been given to the galvanic effect on the overall dissolution rates.

Jan 1, 1993

By H. B. Comstock

This paper reviews the trends in supply and consumption of the principal magnesium compounds in the United States in relation to domestic requirements and world resources. The data are confined to these principal magnesium compounds: Magnesium chloride, magnesium hydroxide, precipitated magnesium carbonate, and magnesium oxide (commonly referred to as magnesia). The properties and uses of magnesium compounds are shown in various chapters of' the 2nd edition of Industrial Minerals end Rocks. 3/ The third edition of this reference is in preparation. A more recent description of properties, uses and sources of magnesium compounds appears in a Bureau of Mines publication.4/ The American Iron and Steel Institute and the Refractories Institute have published comprehensive data on the properties and uses of basic refractories. Many magnesium compounds are prepared by the producers to meet specifications set by individual consumers.

Jan 1, 1960

By Donald M. Keagy

How many times have you said or heard someone say, 'What are you doing right now?" And how many times have you heard the reply, "Breathing air!" Probably never, or at most only a few times in a facetious vein. Breathing air is absolutely necessary to sustain human life, and yet most of us take it completely for granted. Beginning ten to fifteen years ago there was growing concern on the part of the general public that pollution of the air is a threat to man's health and welfare. Concurrently much thought and effort was devoted to the task of defining and resolving the problem of air pollution. In the course of this effort it has become quite clear that our National policy in this regard should be founded upon three basic axioms: (1) Action should not be postponed until emergency conditions make it compulsory; (2) The air cannot be purified after it is polluted, and (3) Air pollution control cannot be accomplished without close cooperation among all levels of government, industry, and the public.

Jan 1, 1967

By P. W. Erickson

Development of the Twin Buttes mine entailed the largest known preproduction stripping job in the history of mining. It linked earthmovers and conveyor belts in a new approach to development of a pit that may reach, or even exceed, dimensions of 1 x 1-1/2 miles at the surface and go as deep as 1800 feet. The orebody to be stripped was covered by an average of 460 feet of alluvial gravels, which presented an initial stripping job of great magnitude. The initial pit layout and the original time schedule established early in 1965 called for the excavation and disposal of about 250,000,000 tons of alluvial overburden before the end of 1969. Allowing about a year for equipment delivery, this schedule left four years to do the job averaging about 62-1/2 million tons per year. In 1964 when The Anaconda Company undertook the development of Twin Buttes, it was recognized that special planning was necessary for the disposal of waste material and tailings. Environ- mental control was a prime consideration and is particularly sensitive in the Twin Buttes area due to the proximity to residential developments. Disposal of the 250,000,000 tons of alluvium, as well as future rock and tailing waste material, presented a problem which Anaconda engineers resolved by designing a plan to spread out much of the alluvium over an extended area, including a massive 11- 1/2 mile dike system which will impound mill tailing in three basins. The tailing will be impounded behind these-dikes to avoid wind exposure and blowing. The dikes also serve as a

Jan 1, 1974

By Milton Hood

The Copper Flat Property is located approximately 6 miles NE of the small town of Hillsboro in Sierra County, N. M. (Fig. 1). Hillsboro was the center of considerable mining activity in the late 1800's and early 1900's following the discover, of gold bearing vein deposits and later discovery of, placer gold along the east slopes of the Animas Hills. The Copper Flat orebody is a porphyry type deposit occurring in a small quartz monzonite porphyry stock that has intruded the center of a circular andesite plug (Fig. 2). The primary ore mineral is chalcopyrite. By-product values are contained in gold, silver and molybdenum.

Jan 1, 1983

By R. J. Beckman

This paper traces the history of mica mining in Alabama from 1870-1970. The decline of sheet mica production is noted and emphasis is placed on the more recent activity of scrap mica production and the development of the U. S. Gypsum Co. mica properties in Randolph County, Prospecting for weathered pegmatites of sufficient size to warrant development is a continuing challenge since most deposits are too small and all exhibit varying characteristics as to size, shape, and weathering. Quantity and quality of muscovite mica in the pegmatites is of utmost importance and its recovery during processing of the ore is described.

Jan 1, 1970

By B. Catalano, D. Ifrim

The Annacis Island Outfall Project includes two TBM bored tunnels with face pressures above 3.5 bar, with an internal diameter of 4.2 metres. This paper discusses the innovative approach to TBM tunnelling and TBM design at the Annacis Outfall Project. The TBM custom design includes a 3.6 m OD core machine manufactured by Herrenknecht and a 5.0 m add-on by the Contractor (Bessac), acting as an extension kit, with optimized gantry design to accommodate for short tunnel drives and quicker launches. This novel design approach produced safety improvement, cost and schedule savings while streamlining logistics of TBM retrieval.

Dec 1, 2022

By O. A. Velasquez, A. R. Kumar

"Continuous miners are often equipped with a flooded-bed dust scrubber to clean the air from close to an active underground coal mining face. However, its impingement screen is prone to clogging due to an accumulation of dust, thereby lowering the scrubber’s efficiency and potentially exposing the mine workers to higher levels of dust. Fans can compensate for the increased resistance by varying their operating parameters, but the scrubber screen needs significant maintenance which leads to downtime. The authors have proposed a suitably sized Vortecone as an alternative to the conventional flooded-bed dust scrubber system. Water is used as the filter medium, which is replaced and recycled continuously. Preliminary CFD investigations of Vortecone scrubbers have indicated higher cleaning efficacies, especially in the respirable range. This paper presents the results including the flow characteristics and capture efficacies of a full-scale Vortecone. Multi-phase flows, including free-surface modeling and particle tracking methods, have been adopted. ACKNOWLEDGEMENT The authors acknowledge the National Institute for Occupational Safety and Health (NIOSH) for funding this research project. This research is being developed with the support of a NIOSH Grant 200-2014-59922- ‘Coal Mine Dust Mitigation through Novel Scrubber Development and Numerical Modeling’. The views expressed in this paper are those of the authors and do not necessarily reflect those of NIOSH. This project is aimed at designing novel and efficient scrubbing systems for underground mining operations. The authors acknowledge Dr. Thomas Novak of the Department of Mining Engineering, the University of Kentucky for his support and encouragement. The authors also thank Dr. Sunil Vytala, CFD engineer at Cradle CFD for his invaluable inputs to the numerical models.INTRODUCTION Continuous miners are the main production machines deployed in room and pillar mining operations. These miners extract coal by the shearing action of the wethead cutting drums. Strategically placed water sprays on the drum not only cool the bits extending their useful service life, they also suppress the dust at the point of generation itself. A flooded-bed dust-scrubber (Campbell, et al. 1983) is usually integrated onto the continuous miner to arrest dust from close to the active face. These fan-powered scrubbers have an impingement screen flooded with water, which also serves as the filter element. A demister downstream of the screen removes the excess water from the air cleaned. These conventional scrubbers have been found to be very effective in alleviation of respirable dust levels underground (Chao and De-sheng 2000) (Colinet, Reed and Potts 2013). However, the inefficiencies of the flooded-bed dust scrubbers arise out of their internal components. Depending on the mining conditions, the screen may be clogged by the accumulation of the trapped dust particles. The resistance of the scrubber system is increased reducing the airflow. The flooded-bed dust-scrubber system would, therefore, require frequent maintenance of the screen and the demister (Listak 2010). Since any maintenance needs to be carried out under supported roof, this leads to loss of availability of the equipment as well. In addition to this, the continuous miner operators could be exposed to elevated levels of dust when satisfactory airflow at the face is not achieved."

Jan 1, 2018

By John S. Livermore

I feel very privileged to be added to the distinguished group that has received this award since the first recipient, Reno Sales, received it in 1954. If my research is correct, the last geologist to be honored was Bill Callahan in 1982. Perhaps the Awards Committee decided it was about time to select a geologist, and I became the beneficiary. Regarding the discovery of the Carlin ore body, it was the culmination of several studies - one going back as far as 1939 when a US Bureau of Mines engineer named W.O. Vanderberg recognized an unusual type of gold mineralization in sediments in northern Nevada. What was unusual was the fact that the gold was so fine that it would not concentrate in a pan. This, plus the study of the Roberts Mountain thrust by Ralph Roberts (1960) and conversations with Harry Bishop, manager of the Gold Acres Mine, pointed Alan Coope and me in the direction of the Lynn Window and, eventually, the Carlin discovery. There has been a great deal written about this discovery. I thought it would be interesting to discuss the evolution of Carlin gold exploration in Nevada since this time and to discuss the changes in perception of this unique type of mineralization. The method used by Coope and me in following up on Roberts' work was to map geologically the Roberts Mountain thrust and conduct geochemical sampling of favorable outcrops and float. Coope was highly experienced in geochemical exploration, as he had graduated from the Royal School of Mines in London, studying under John S. Webb, one of the pioneers of geochemistry as applied to mineral exploration. We first considered using pathfinder elements, but finally concentrated on gold analyses alone, even though the sensitivity of fire assays used at that time was only about one-half part per million. According to the spatial relationship of the mineralization to the Roberts Mountain thrust, as pointed out by Roberts (1960), we were looking for mineralization within the thrust itself. Our models were the known Gold Acres and Getchell mines, which contained reserves on the order of 0.9 to 1.8 mt (1 to 2 million st). These were not of substantial size, but I had hoped we might find more than one of these tributary to a mill that would justify an operation for our employer, Newmont Mining Corp. What we ended up with was the type of deposit we were looking for - an open pit deposit of micron gold, which the old timers had missed because the gold was not capable of being panned. But never in our wildest dreams did we think there was a chance of finding a body containing 10 mt (11 million st) of ore at 0.30 oz/st (10.3 g/t).The deposit was not in the thrust proper but was found in a favorable horizon of Roberts Mountain siltstone that was below the thrust. This is the first example of how a model should not be followed blindly. Newmont was successful in keeping this discovery quiet for some time. After a considerable amount of drilling, a rumor circulated that they had discovered a large low-grade ore body of around 1.7 to 2.1 g/t (0.05 to 0.06 oz/st), which of course would not have been economic with gold at $1.13/g ($35/oz), which was the fixed price at that time. The company, for obvious reasons, did not discourage the rumor. When, however, the true results came out there was a lot of feverish activity. Because of this new type of so-called "invisible gold," which could have been missed by the old timers, the thought was that other deposits would be discovered very soon. The Carlin and other smaller deposits, including Bootstrap, Blue Star and Gold Quarry, were in windows where the lower plate of the Roberts Mountain formation (below the thrust) had been exposed by erosion. This then became the new

Jan 1, 1997

By L. Yuan, R. A. Thomas

"Atmospheric monitoring systems (AMS) have been widely used in underground coal mines in the U.S. for the detection of fire in the belt entry and monitoring of other ventilation-related parameters such as airflow velocity and methane concentration in specific mine locations. In addition to an AMS being able to detect a mine fire, the AMS data has the potential to provide fire characteristic information such as fire growth (heat release rate) and exact fire location. This information is critical in making decisions regarding fire-fighting strategies, underground personnel evacuation, and optimal escape routes. In this study, a methodology was developed to calculate the fire heat release rate using AMS sensor data for carbon monoxide (CO), carbon dioxide (CO2), and airflow velocity based on the theory of heat and species transfer in ventilation airflow. Full-scale mine fire experiments were then conducted in the Pittsburgh Mining Research Division (PMRD) Safety Research Coal Mine using an AMS with different fire sources. Sensor data collected from the experiments were used to calculate the heat release rates of the fires using this methodology. The calculated heat release rate was compared with the value determined from the mass loss rate of the combustible material using a digital load cell. The experimental results show that the heat release rate of a mine fire can be calculated using AMS sensor data with reasonable accuracy. INTRODUCTION Fires at different stages generate different gases and smoke toxicity hazards. When fires occur in underground mines, a significant amount of toxic gases and smoke enter the mine ventilation system and are carried throughout the mine ventilation network, increasing the hazard potential for personnel even if far away from the actual fire. Although fires that develop to the point of rapid flame spread pose imminent hazards, fires in their smoldering, pre-flaming stages can also contaminate the mine atmosphere with debilitating levels of smoke and toxic gases. The most important parameter for evaluating the fire hazard in mines is the heat release rate (HRR), which is directly related to the rate at which heat, smoke, and toxic gases are produced and transported by the ventilation system, and provides an indication of the time available for escape or firefighting [1]. The HRR is also an important input parameter to mine fire simulation models. Measuring the HRR of an actual fire can be a difficult task. Early experimental measurement of HRR focused on the heat output as represented by the temperature of the product gases. In ASTM E1321 (LIFT test), an array of thermocouples was positioned in a duct which captured all gaseous combustion products to measure their average temperature. This approach assumed the flow is adiabatic, which is never a reality. Significant progress on measuring HRR was made when Huggett showed that, for most common materials containing C, H, O, and N, the average heat release per unit mass of oxygen is 13.1 MJ/kg O2 [2]. Thus, the oxygen deficit is a measure of the HRR in the flow that the duct captures. This approach is termed oxygen consumption calorimetry (or the oxygen consumption method), and is widely used in the fire protection community."

Jan 1, 2017

By Michael Davis

In the fairly recent past, with a history of cheap and abundant energy, it has been possible to predict with reasonable confidence that world energy demand would continue to double about every 15 years. Those who attempted to forecast the role of nuclear energy in future electricity generation could also start with the fairly safe assumption that electricity demand would increase even faster : with a doubling in demand about every 10 years. To estimate the likely future world demand for uranium it was then necessary to introduce a number of other assumptions including the rate of penetration of nuclear energy, the timing and the specific fuel requirements. This series of assumptions naturally compounded the uncertainty, but, remarkably, usually led to future uranium demands being overestimated. Such a bias which has almost always been observed in predictions made over the past 20 years has increasingly made uranium producers sceptical when expected to match the forecast demand with increased production capacity and supporting reserves. This scepticism has, of course, been reinforced by the persistence so far of a buyers' market in uranium throughout the entire period of emergence of commercial nuclear electricity generation.

Jan 1, 1974