Search Documents

By Tan Zhenxiang

INTRODUCTION Koolyanobbing is an open cut iron ore mine, which is located in Yilgarn region of Western Australia. To prevent the operators from suffering silicosis diseases and protect the air from being polluted, a series of dust control measures have been taken. These measures include ventilation and dust control system for sample preparation shed, dust collecting system for drill rig, dust suppression system for ore processing plant, dust control for haul road. The details related to individual dust control measure are dealt as follows. SAMPLE PREPARATION SHED DUST CONTROL The sample preparation is one of the major dust sources at Koolyanobbing. The activity is being carried out at the sample preparation shed. It typically needs to go through the following stages, that is, crushing, splitting, drying and pulverising. The amount of dust generated from crushing and splitting is mainly determined by the moisture content contained in the pre- pared sample. A significant amount of dust is generated at the sample pulverising stage due to cleaning sample bowl with com- pressed air. To protect the sample preparing personnel's health and make the dust level in the air meet the requirement from the health and safety authority, a central ventilation and dust control system has been installed at the sample preparation shed. As shown in Fig. l, the system consists of suction heads, suction lines, dust collector and vacuum fan. The fan creates vacuum environment in the system, therefore the dust is drawn into the dust collector through the suction heads and suction lines. The dust collector is of fabric filter. When the dusty air comes to the filter, the dust in the air is collected and retained on the surface of the filter while the clean air passes through and enters the atmosphere. The retained dust is blowed out by the pressured air pulses and deposits into the dust bin underneath the filter. A time relay device is used to control the cleaning time and the cleaning interval. DRILL RIG DUST CONTROL A hydraulic percussion drill is used to drill blast holes. To carry out the drilling operation properly and efficiently, the cut- tings are being flushed out of the hole by the compressed air. In order to prevent from the fine particles in the cuttings escaping to the air, a dust collector is attached to the drill. The collector mainly consists of suction head, cyclone and bag filter. Refer to Fig. 2. The suction head is installed at the lower end of the feed beams and is movable. The moving range is up to 250 mm. It is not only used to restrict the cuttings, but also used to prevent water from entering the filters when drilling wet hole. A 406 mm diameter primary cyclone is used to separate the heaviest particles in the cuttings. It is also used as blast holes sampling equipment. One part of the dust particles are collected by a sample bag through a splitter attached to the end of the cy- clone. The rest of the particles fall down to the ground through the closing rubber. The bag filter is driven by a hydraulic motor (1). It is used to collect the lighter particles in the cuttings. The filtering area is 16 m2 and the dust separation efficiency is up to 99.9%. The working principle of the filter is demonstrated in Fig. 3. When the rock drill (9) flushing is turned on, the pressurised air from the compressor is directed to the rock drill and to the pres- sure switch (10). The pressured air will open the pressure switch to de-energise and close the solenoid valve (4) The pressure affecting the cut-off cylinder (5) keeps the exhaust port flap open. When the flushing valve (8) is closed, the pressure affecting the cut-off cylinder disappears and the internal intake opening flap is closed by a spring. The pressure also ceases to affect the pressure switch and the spring switches the contact to the point 2. The time relay (11) is now activated and gives a 0.5 second current impulse to the solenoid valve and keeps the current cut off for approx 8 seconds. When the solenoid valve is live, it opens and lets an impulse of pressured air to the filters (2). These impulses will clean the filters.

Jan 1, 1997

By Nasri Munfah, Raymond E. Sandiford

"Superstorm Sandy (Sandy) created a storm surge that inundating many of the tunnels that pass beneath the Hudson and East Rivers. The tunnels are vital infrastructure links for the economy of New York City and the northeast region. The sea water, which contains highly reactive salts, caused significant damage to electrical and mechanical systems. In addition, the salt water inundation left corrosive precipitants on the tunnel linings and on and within electrical duck banks. After the salt water was evacuated from the tunnels, condition assessments were performed using a state of the art approach involving high resolution laser scanning, digital imaging, and thermal imaging. These scans were performed prior to hands on inspections. The damage assessment concluded that, although the tunnel structural linings were not damaged, the interior elements of the tunnels needed major rehabilitation to arrest the continual deterioration of the structures. This paper details the state of the art approach used for these tunnel inspections. INTRODUCTION On October 29, 2012 Super Storm Sandy flooded a large number of both transit and vehicular tunnels in the New York Metropolitan area. The region’s transportation network was severely disrupted. The storm damage is estimated to have been in excess of $30 billion, and with the tunnels out of service, the local economy was losing hundreds of millions in economic activity. Restoration of these tunnels was a very high priority and the resulting expedited restoration process did not always provide adequate time for comprehensive condition surveys. This resulted in many of these surveys being conducted after service restoration. Inspecting highly trafficked transit tunnels is challenging and the logistics of working in short night outages led to a rethinking of the conventional inspection approach. Traditionally, visual and tactile methods are first used to inspect tunnels and then quite often followed by LiDAR (Light Detection and Ranging) scanning and perhaps infra-red scanning. For multi-mile tunnels, the time required to visually map tunnel features can be quite extensive. By performing the scanning first and then performing the visual and tactile inspections, one is able to use the scan data to identify the specific areas that need detailed inspections. This approach was used quite successfully for a number of the NYC tunnels."

Jan 1, 2016

By John W. Greene

ennec?tt's Bameys Canyon Mine personnel developed an mnovahve process to extract gold from a small (1.8 million tons) sulfide ore zone in an oxidized ore body located at the Bameys Canyon Mine. This approach consists of extracting the sulfides from the ore via flotation, shipping the concentrate to Kennecott's new smelter, and mixing the flotation tailings with the oxide ore, agglomerating the mixture, and stacking the resultin tailings/oxide ore combination on the heaps. Conventional heap leaching technology is utilized to recover the gold from the mixed materials. Overall, the total gold recovery from the sulfide ore is esti­mated to be 90%. This approximation is based on a smelter gold recovery of 98% from the concentrate and an 88% recovery from the tailings during heap leaching

Jan 1, 1996

By F. Lincoln & B. Rodier, G. Poniatowski, N. Kawashima, T. J. White, J. H. Kyle, G. F. Eaton

The history of Australia is a narrative of the discovery and development of its mineral wealth. The gold strike at Ballarat, Victoria, in 1851 transformed the colony by triggering the first great influx of migrants to Australia, and the development of subsequent mineral discoveries lead to a vast resource industry. However, beneficiation of base and precious metal ores carried with it an environmental penalty, not addressed until the last quarter of this century. In particular, the extensive deposits of gold, silver, lead, copper and zinc reside in sulphurous ores which often contain arsenic, antimony and mercury as significant contaminants that are released as unwanted by-products during smelting and refining. Until recently, these toxic concentrates were discharged to the atmosphere or receiving waters, collected in tailings ponds close to the smelters, or dumped at sea. Although such procedures . were acceptable in the past, more stringent environmental controls have required a re-examination of these practices and encouraged intensive efforts to develop enduring solutions to the disposal of these wastes. From this research has emerged a promising new generic technology called Xtaltite (pronounced crystal-tight). In this approach, geochemical principles are employed, first, to reduce the toxicity of heavy metals to low levels, and second, to identify and engineer suitable repositories for the permanent disposal of the consolidated waste form. In this paper, we emphasise the application of Xtaltite to the disposal of arsenious smelter fumes derived from gold winning. The principles ofXtaltite will be described and its technical and economic performance compared with conventional technolo­gies.

Jan 1, 1995

By Aladar B. Dory

INTRODUCTION Practical experience in mines with known presence of radon daughters in the mine atmosphere in Canada and elsewhere shows that a very high concentration builds up in an unventilated dead end heading. As Holaday et al1 observed, even a minimal air movement results in a drastic reduction in radon daughter concentration. It is therefore obvious that the main objective of radon daughter control in the working environment is to design the ventilation system providing an optimized flow of fresh air into the workplace, resulting in acceptable climatic conditions and achieving radon daughter concentrations resulting in exposures as low as reasonably achievable. BASIC OBJECTIVES Large mining companies, having extensive material resources and professional expertise, have utilized elaborate electrical modelling in the design of mine ventilation systems as early as 1950 (coal mining industry in Europe) and with the advance of computer modelling techniques, their utilization in ventilation systems design is on the increase. Unfortunately, these methods are usually not available to small mining companies and even the large companies might not achieve the fullest benefit from utilizing them, if proper limiting factors are not considered in the modelling. When an evaluation of a ventilation system of a mine is undertaken in literature, a measure of the amount of air supplied underground per one ton of ore mined is used as an indicator of the efficiency of the ventilation system. Yet, even the greatest amount of air forced into the mine might not result in an acceptable working environment if a proper distribution of this air into individual working places is not achieved. The volume and the age of the air are probably the two most important factors in achieving acceptable radon daughter concentrations in the workplace, but other factors also have to be considered. DIRECTOR MINE - ALCAN, NEWFOUNDLAND FLUORSPAR WORKS ST. LAWRENCE, NEWFOUNDLAND, CANADA Ventilation To illustrate the effects of the design of the ventilation system on the control of radon daughter concentration, let us review the gradual development of the ventilation system of this mine from the earlier years of its development up until its final years of operation. This mine, located near the community of St. Lawrence on the south coast of Burin Peninsula was developed in the late thirties and reached full production by 1942. Unfortunately as was customary at that time, the only source of ventilation was a natural draft. The mine was extremely wet, and no significant attention was initially given to possible health effects of dust. It was not until the mid-fifties, when a number of cases of silicosis had surfaced, that de Villiers and Windish2 observed a significant increase of lung cancer incidence among the miners in comparison to its incidence among the general population of Newfoundland. Suspicions regarding radiation as a cause of the lung cancer were expressed, but it was only in surveys taken in late 1959 and early 1960 that Windish3 and Little4 established the presence of radon daughters in the mine atmosphere in very high concentrations. Windish, de Villiers and Hurley suggested that the most likely source of the radon in the mine was the mine water which dissolved radon during its passage through the granitic country rock in the surrounding geological area. This conclusion was confirmed by analyses of water from various areas of the mine by the Atomic Energy Canada Limited laboratories. The radon values in the samples varied from 4,240 to 12,850 pCi/L5. Following the discovery of the presence of radon daughters in the mine, the company took speedy action to install mechanical ventilation for the mine. The system was not designed as a total unit, but fans were installed rather on a trial and error basis. The basic system installation began in March 1960 and was completed by 1962. It remained basically unchanged with only minor modifications until August 1973 when a wholly new, redesigned ventilation system was implemented. A schematic section of the mine and its ventilation system for the period prior to March 1960 is given in Figure "A", for the period 1960-1973 in Figure "B", and for the period after August 1973 in Figure "C". The ventilation system prior to 1960 is not known. All workings of the mine were ventilated only by natural ventilation. If any measurements of airflows at different or any times of the year ever existed, no records have been preserved. The very minimal natural ventilation was augmented by "blowing" air from compressed air supply lines and exhaust air from drills. It is known that the compressor capacities of the mine were limited and therefore no significant air movement was probably created by the "blowing".

Jan 1, 1981

By G. B. Walker

The success of Heavy Media Separation, the static sink-float process, is evidenced by the operation of an estimated 300 installations treating many millions of tons per year of a wide variety of mineral products ranging in value from gravel to diamonds. The static heavy media process is usually limited to the treatment of plus 1/4 inch material. Mr. Victor Rakowsky, who was largely instrumental in the development and application of heavy media separation, recognized the need for a new apparatus and process which would extend the application of heavy media into the finer size range without placing a restrictive limit on the top size of the feed. He recognized the requirement for the application of centrifugal force to augment the force of gravity in separating fines by sink-float techniques.

Jan 1, 1966

By Gareth Mainwaring

The Cross Harbor Freight Movement Project is currently in the Environmental Impact Statement phase. The scheme is addressing alternative solutions to transport freight across the Upper Bay of New York Harbor, from New Jersey through to Brooklyn, Queens and Long Island. Amongst the alternatives being assessed are two tunnel options; from the north shore of Staten Island through to Brooklyn, and from Jersey City to Brooklyn. These tunnels are approximately 30,000 feet in length, and with up to17,000 feet under the Harbor, would make it one of the longest undersea crossings in the world.. The paper addresses the development of the project, from the Major Investment Study through to the current EIS, and describes the tunnel schemes that are being taken forward. The geological conditions that will be encountered, proposed construction methods, and the ventilation issues associated with such major undersea tunnels will all be described.

Jan 1, 2003

By E. D. Thompson, Y. J. Zhang, K. F. Unrug

This paper presents the results of a recent study on the development of an in situ testing method for determining coal strength in mine pillars. The strength testing is performed in the horizontal holes drilled into the coal rib using a penetrometer, which is an hydraulically powered device that uses an indenter to press on the surface of the borehole until the load reaches the failure point of the coal. The pressure and the penetration of the loading pin are recorded by a data-acquisition unit. The results collected from several coal mines indicate that this testing method is ideally suited for the realistic coal strength measurements. The new testing system not only improves the accuracy of the pillar-strength determination, but it is more cost efficient than the conventional method.

Jan 1, 1997

By Scott G. Britton

In this chapter, I shall discuss railroad con¬struction for modern underground coal mines. Because men, materials, and supplies are being moved more often and farther by rail, the ef¬ficient and safe construction of the system takes on new importance. Most large coal mines are opting to use track haulage over other support transportation systems because of cost, ease of installation, reliability, and other factors. En¬gineers tackling the problem of designing such a transportation network must be aware of all the steps required for an effective transportation system design. This chapter discusses all aspects of efficient trackwork construction. The areas covered in¬clude design factors, laying the track, installing turnouts and switches, and installing trolley wire. Each area includes a description of the steps needed to complete the work.

Jan 1, 1983

By David M. Spatz

Team, as defined by Katzenbach and Smith (1993), is a small number of people with complementary skills who are committed to a common purpose, performance goals and approach for which they hold themselves mutually accountable. As the mining industry searches for new ore discoveries increasingly under post-mineral cover, the process of mineral exploration has taken us from prospector to geologist to multidisciplined explorer to multi-disciplinary team. Multidisciplinary exploration techniques have improved in terms of sensitivities and penetration and more than ever before each technique requires specialists with appropriate training and skills to process data and interpret results. To produce a quality product, specialists must collaborate openly and honestly in an atmosphere where the collective result takes into account the knowledge and expertise of each individual and the relationships between all pertinent data sets.

Jan 1, 1998

By Kenneth J. Reid, Marian S. Stachowicz

A preliminary evaluation of a new in-stream particle size analyzer has been carried out using materials obtained from a taconite plant in Northern Minnesota. Results are reported for bench scale, pilot scale and full scale tests, the latter being carried out in a taconite plant concentrator. The unit employs a novel scanning laser microscopy principle and details of the equipment configuration and operating principles are presented and discussed. Data acquisition is via an eight channel digital electronic system and particle counts are collected on the basis of reflected light pulse time intervals which are a direct measure of particle size. Output is available as an eight point individual or cumulative size distribution or as computed averages. The practical aspects of sample point location and flow requirements for reproducible results are outlined and discussed.

Jan 1, 1990

By Richard A. Thomas, Liming Yuan, Lihong Zhou, James H. Rowland

Hydrogen (H2) gas released during battery charging can result in cross-interference for carbon monoxide (CO) sensors used for early fire detection and compromise the integrity of the mine atmospheric monitoring system (AMS). In this study, a series of laboratory-scale and full-scale experiments were conducted to evaluate the responses of different CO sensors to H2 gas. In the laboratory-scale experiments, constant H2 concentrations in the airflow, from 100 to 500 ppm, pass through sensors. While in the full-scale experiments, increasing H2 concentrations generated as a byproduct from charging the batteries at the battery charging station rise to the sensors under different ventilation scenarios. The H2 concentrations at the CO sensor location were measured using H2 sensors and were correlated with the CO sensor response. The effects of ventilation and sensor location on the CO sensors responses were also analyzed. The results of this study can help mining companies to select appropriate CO sensors and improve the deployment of these sensors to ensure the safeguard of underground miners.

By Jiang Su, Michal Uhrin

"The use of composite linings, consisting of permanent sprayed primary and secondary linings with a sandwiched spray applied waterproofing membrane is expected to improve efficiency and reduce lining thickness, but it also brings complex primary-secondary lining interaction. This issue is further complicated by the uncertainty regarding the long-term behavior and parameters of the sprayed concrete–sprayed membrane interface.This paper aims to address this issue by presentation of a series of numerical analyses of a typical shallow SCL tunnel in soft ground with a range of design assumptions on the interface behavior: (1) compression only; (2) compression and tension; and (3) compression, tension, and shear.The results demonstrate that the assumed interface behavior has a significant impact on the primary-secondary lining interactions. A design approach of ignoring the tension and shear bond at the interface may not be conservative particularly for serviceability. This paper explains the rationale behind these conclusions and discusses the implications for design.INTRODUCTIONSprayed Concrete Tunnel Lining SystemsSprayed concrete linings (SCL) have been used in conventional tunneling for decades. However, details of SCL systems may differ to a large extent depending on ground conditions and specific tunneling methodologies.In hard rock conditions, for example, drill and blast excavation is typically supported by rock bolts and sprayed concrete (NGI 2014). Such tunnels are usually designed fully drained and the above-mentioned support elements considered permanent without the need for a further inner liner. Therefore, there is no structural interaction between separate lining shells to consider.In conventional tunneling in the European Alps, a double shell lining is typically utilized, consisting of an outer (primary) sprayed concrete lining and an inner (secondary) cast-in-place concrete lining, separated by a waterproofing system. The primary lining normally includes rock bolts and may include other support elements. The waterproofing system is usually based on a plastic membrane and a geotextile fleece. The tunnel may be designed fully or partially drained or fully undrained. Although there are two structural lining shells interacting, investigation of such interaction is generally irrelevant to designers because the primary lining is considered only temporary (fully sacrificial in the long term). An overview of reasons for this assumption is given, for example, by Lemke (2014). The secondary lining is designed to resist all foreseeable loads on the tunnel. The primary lining may, in reality, interact structurally with the secondary lining during the life span of the tunnel. However, since the secondary lining design must cover all possible (extreme) scenarios, investigation of such interaction does not bring any value to the design."

Jan 1, 2016

By Kirk Carlton

This paper deals with a group of subjects so familiar to all of us that we might question the need for discussion. Even so, nearly every day's business turns up expensive examples of differences in understanding, misdirected assumptions and incomplete technical purchase documents. As our international activities increase, so do these problem areas. Their expense in both money and embarrassment gives rise to this attempt to focus a little extra attention on technical criteria and specifications. The two terms ?criteria? and "specifications" are, we believe, worth separating with respect to meaning. They should not be used interchangeably, although they often are. Criteria are by definition "standards for judging", whereas specifications are "enumerations of particulars". In relation to plant or project engineering, the criteria are the general rules and data which apply to the whole project and the specifications are the further listing of detailed requirements for specific contractual items or pieces of equipment. We'll look a little more closely at specifications after we give another minute or two to this "criteria" subject,

Jan 1, 1973

By K. Baba

Liberation of valuable minerals from a gangue matrix during size reduction of multiphase mineral particles is an important objective in mineral separation processes. A methodology for the prediction of volumetric grade distribution from one dimensional, linear intercept image analysis is being developed using a transformation function to describe the relations hi p between the linear and volumetric grade distributions. As part of this research effort it has been found that a transformation function, derived from Monte Carlo simulations of irregularly shaped particles, mainly depends on the volumetric grade and the dispersion density, i.e., the number of nuclei (or grains) per particle. A possible mathematical form for the transformation function is described in detail.

Jan 1, 1985

By D. N. Madge

A survey is given of production scheduling systems currently in use or contemplated for future use in Cominco operations. Emphasis in this presentation is made on the chain of decisions that are made with the help of mathematical programming models. Some attention is devoted to the structural properties of the models.

Jan 1, 1966

By Brij M. Moudgil, Shoulian Zhu, J. L. Pinault

A new technique, prompt neutron activation probe (PNAP), for analyzing phosphate rock slurry in-situ was evaluated both in the laboratory and at the plant. The technique yielded a high precision in the analysis of Ca, Si and H using 252Cf source. Low accuracy of the direct measurement of P using 241Am/Be in the laboratory tests was attributed to the interference of rare earth elements present in the samples, particularly Gadolinium. No significant effect of variables such as solids loading, particle size distribution, and flotation reagents was observed on the probe performance. The probe can detect the compositional changes of the feed, tailings and the concentrate streams in the plant.

Jan 1, 1993

By Vincent C. Grimshaw

High pressure fluid energy grinding, or jet milling, is a versatile method of continuously fracturing solids into fine particles to gain substantial increases in exposed surface area. Applications in the minerals industries include calcium carbonate, talc, barytes, mica, diatamaceous earth, bauxite, rutile, coal, kaolin, sepiolite, diamonds, etc. The basic principles can be extended to provide continuous drying and delivery of discrete particles from a wet process slurry. The main design and operational features of jet mills and dryers are described, relating energy consumption for both air and steam milling and hot air drying techniques. Mean particle sizes in the order of 1 micron are achieveable from pre-milled feeds, or maintained from similar slurries in the drying mode. Aspects of feed preparation and multi-stage processing are discussed.

Jan 1, 1983

By Gerald P. Kelton

Over the past quarter of a century, the success of the hydrocyclone as a classifier in closed circuit grinding installations has permitted the introduction of the cyclone into virtually all fields of wet industrial processing. Research and experience gained in these applications have established the optimum cyclone sizes and designs necessary to provide the required performance. Although cyclones are used in widely diverse liquid-solid applications, their use for ultrafine separation clearly demonstrates the importance of a familiarity with previous case studies. Krebs Engineers is firmly dedicated to serving the process industry and has acquired the unsurpassed knowledge and experience to handle all types of separations and classification problems. Cyclones have been used for a number of applications to make what might be considered fine separations. A typical example is in an iron ore grinding circuit where a 381 mm diameter cyclone will classify an overflow product to 85% -44 micron. There is no question that this is a fine separation, but still finer separations are possible, and these are known as ultrafine separations.

Jan 1, 1983

By R. L. Teseneer

Pyrite samples from twenty-one locations in the North Carolina Slate Belt were analyzed for cobalt, gold, mercury, and nickel by atomic absorption spectrophotometry. The geographic distribution of relatively high values of certain trace elements in pyrite suggests that, in addition to gold, cobalt and nickel metallogenetic provinces are possible in the slate belt. Northwest trends of province boundaries may be genetically related to subsurface features rather than to surface geology. Within province boundaries gold and nickel exploration programs should be concentrated in areas containing intermediate to mafic tuffs, while cobalt may be more concentrated in argillites and phyllites.

Jan 1, 1979