Search Documents

By Ron M. Canon, John M. Begovich

Chromatography, ion exchange, and other techniques based on the interaction of solutes with solid phases offer versatility, high resolution capabilities, and near-universal potential applicability for the separation of valuable constituents in liquid solutions. The expense associated with obtaining reasonable throughput for these separations has been the only, albeit overwhelming, obstacle preventing widescale use of these methods. Attempts to devise continuous (cheaper) systems have previously resulted in moving, or simulated moving, beds of resin with complicated valving and timing sequences. These disadvantages, plus technical problems associated with the disturbing effects of non-plug flow and reduced resolution of moving versus packed beds, severely limit applicability of these systems. Over the past decade a new device has been developed that overcomes many of these problems. It utilizes a slowly (less than one revolution per hour) rotating annular bed of sorbent material with fixed-feed inlet and product withdrawal points. Numerous units of various diameters and lengths have been fabricated and operated, and a parallel effort has developed a satisfactory theoretical treatment of the device. Several simple control systems have been incorporated to thoroughly demonstrate the simplicity of operation, even for multiple products and multiplecarrier flows. This device has been developed using several metal solutions and has demonstrated its power with some of the most difficult, including the zirconium-hafnium, separations. Design equations are available for sizing units based on simple laboratory data and have been tested for units as large as 18 in. in diameter.

Jan 1, 1985

By Douglas Owen

Two case studies describe the introduction of technology new to an organisation. The lessons learnt from these Case studies contribute to Our general understanding of the management of technological change.

Jan 1, 1989

By H. Sevim

In long-term open pit production planning, a series of nested and maximum-value pits is usually generated first. These pits are then considered as possible pushbacks over a number of planning periods. To determine the best pushback in each planning period, the pits are evaluated for their technical and economical feasibilities under certain production constraints. Parameterization is a commonly used technique to generate a series of pits. In almost all cases, however, some of the consecutive pits generated by this technique are too far apart from each other. This is called the "gap" problem. It may make the entire pit series useless for production planning purposes. A new pit gener¬ating algorithm has been developed to overcome the gap problem. Through this algorithm, a series of nested maxi¬mum-value pits can be generated with a controllable size increment. The logic of the algorithm is illustrated through a small hypothetical case. Its capability of generating maximum-value pits that are as optimal as those generated by parameterization and its advantages over parameteriza¬tion are presented through an actual gold deposit case.

Jan 1, 1996

By Douglas J. Pendrell, Marvin D. Simmons, E. Raymond Boc

The U. S. Army Corps of Engineers is in the early stages of design for an estimated 14 m (46 ft) diameter tunnel in northeast New Jersey. This tunnel will carry flood waters from the upper end of the Pompton River in Wayne County, to an outlet in Newark Bay, a distance of 33 km (20.5 miles). The tunnel will be constructed by a tunnel boring machine (TBM), the size of which is unprecedented at the present time. The alignment is through Triassic and Jurassic sandstones, siltstones, and shales that include three beds of basalt that range in thickness from 76 to 310 m (250 to 1020 ft).

Jan 1, 1991

In a world dependent in part on the consumption of depletable natural resources, development of new areas of mineralization is a necessity for replacing those reserves. Exploration, which is the initial task of replacement, is an information-gathering process which supplies input for management decisions on mine development. If the demand for resources is the driving force of exploration, then the scientific basis for its pursuance is the hypothesis of anomalous mineralization in a metallogenic province, which is tested by measuring physical characteristics of natural phenomenon. The resulting data are reduced, analyzed, and interpreted to locate expressions or responses associated with possible ore bodies. The process is, in fact, repeated in ever increasing measurement detail to increase the accuracy and precision of information for decision making. Exploration ceases when management makes the decision to develop a mineralized area, to hold a property for more favorable market conditions, or to drop a property because it is not economically viable.

Jan 1, 1979

By J. O. Craig Imrie

Mine operations are being squeezed to do more with less. This is not new. But, where do mine operators turn for the next stage of improvement? Many have waged strong wars on the cost reduction front and cut back staff to the bone, yet need more improvement to remain competitive. This paper will outline an approach which a few leading operators have taken. Following the footsteps of manufacturing's view of supply chain management and basic quality management they are reaping the benefits of taking a more holistic process view of their operation. This paper presents summaries of three companies' approaches and the impact which is being felt on the bottom line.

Jan 1, 1999

By Z. T. Bieniawski

After many significant advances in mining including development of sophisticated methods for strata characterization and numerical modeling analyses, the engineering design process in mining is as primitive as it was two decades ago. Yet, major advances in design methodologies have occurred in other branches of engineering. Is creative design in mining a myth only? Are we deluding ourselves when we talk about innovative mining design of today? What is the reality of the situation? This paper explores the methodology of creative engineering design as a new recognized discipline. It warrants applications in mining since design experts are sometimes unaware of their own decision-making processes.

Jan 1, 1988

By R. Milici

Current federal and State coal assessments estimate resources in the ground, resources available for mining, and economically recoverable resources. None of these assessments predict the amount of coal that may be produced from an assessed area in the near future (~20 years). Predictive assessments of coal production would be based on an understanding of the regional coal geology (coal systems), potential demand, and knowledge of the mining history of the region. The output of the predictive assessment would be a supply curve – a probability distribution of the amount of coal expected to be produced from current and new mines during the assessment period. I

Jan 1, 2004

By Leo G. Martin, Richard G. Sherman

Recent sewer construction in downtown New Haven, CT required avoiding open trench methods because of near surface utilities and traffic congestion. The .73 km long alignment is in sands with the water table at the tunnel's springline. The designers felt the situation was ideal for an EPB machine; however, the tunneling method was left to the Contractor. The winning bid surprised everyone. The tunnel is being excavated by hand using an open face shield with breasting boards. The review of the bids indicates hand mining was approximately 1/2 the bid price of TBMs. Currently, excavation rates average 14 m/day with no excessive settlements.

Jan 1, 1993

By John Carson

Belt feeders are commonly used to meter the flow of bulk solids from bins and hoppers. If the interface between the hopper outlet and belt feeder is not designed correctly, flow from the bin may be severely compromised, resulting in problems of no-flow, segregation, flooding, etc. By knowing the flow characteristics of the bulk solid being handled and applying proven design techniques, such problems can be avoided. Relevant bulk solids flow characteristics are identified, along with measurement techniques. Design procedures for correcting problems with existing feeders as well as proper design of new feeders are presented, along with case histories of successful application of these procedures.

Jan 1, 2008

By Mark Gershon

This paper describes an application of a new approach to mine planning and production scheduling in a gold mine. The technique, limited to use in open pit mines (but not limited to gold), has been described previously (Gershon, 1987). The-computer program used is the HOPS software, which has been described previously as well (Gershon, 1988). The mine is scheduled for the production of 8,000 blocks out of a mine having 25,000 blocks (50 x 50 x 10). The technique is based on the concept of inverted cones (Gershon, 1987). While it does not provide a true optimization of results, it does approximate the optimal situation. As opposed to most scheduling software that only serves as a computerized notepad for the scheduler, the use of this approach allows for a scheduling intelligence to be built into the software.

Jan 1, 1989

By Heribert F. Broicher

As of 1998 German companies have been engaged in research and development of LIF analyzers for rock identification, i.e. for the fingerprinting of rock by the analysis of laser-induced fluorescence (LIF). Test work in Germany, Sweden and South Africa showed the potential of this new technique, which operates online and in realtime (1). In 2003 the Finnish company IMA Engineering Ltd Oy commenced building and marketing LIF analyzers under the trade name OreSpex. Today, one OreSpex analyzer has been installed in the Kiruna Mine, Sweden to check the phosphorus content of train loads. In 2004 a second OreSpex analyzer was built for dilution control in the Argyle Diamond mine, Australia. In 2005 another LIF analyzer will be used for test work in various mines in the US. The principles of the technology and status of ongoing work are presented.

Jan 1, 2005

By Dale C. Matthews

The Getchell Gold Hine is located about 40 miles northeast of Winnemucca, Nevada. Gold was discovered at the mine in 1934 and production was started in 1938 and ended in 1967 for its first phase of operation. Gold production during this period was about 800,000 ounces. In 1983, FirstHiss Gold Inc. purchased the property and initiated an exploration program that proved minable reserves of about 1,300,000 ounces of gold remained in the mine. During the exploration period, metallurgical testing was conducted to determine the most economical process that could be utilized for recovery of gold from the very refractory ore. After extensive investigation, pressure oxidation of the ore was selected, Engineering for the new plant commenced in 1987 and construction was completed in 1989 at a cost of about $87,400,000.00, not including financing cost.

Jan 1, 1990

By L. J. E. Hofer, L. F. Zeiler, D. A. Giardino

The Jones Trickett Ratio (JTR) is generally used in investigations of fires and explosions for the determination of the composition of the fuel. This paper takes a close look at the JTR and finds it unreliable and ambiguous for the determination of fuel composition. A new index is presented, termed the (H/C) Index which uniquely determines the fuel composition. The (H/C) Index is simple to use requiring only the results of a single gas analysis of the combustion products. Experimental data testing the (H/C) Index for methane, propane, ethylene and coal dust are given, showing that the Index unambiguously determines the composition of the fuel. The (H/C) Index is also applied to the gas analysis data of several mine fires, illustrating how the Index changes with the progression of the mine fire.

Jan 1, 1993

By J. H. Fewings

The rapidly escalating capital costs for new projects, or extension of existing projects, has placed greater emphasis on maximum use of existing resources. Thus, when increased grinding capacity was required to achieve metal production from lead-zinc ores a number of alternate approaches were studied. The most cost effective way of achieving the required 5% increase in grinding circuit capacity was to install upgraded instrumentation and computer control of grinding - Fewings, Wickham and Wiseman (1). Once the computer installation cost had been borne by the financial returns from that project, other projects involving computer control were economically viable on an Incremental cost basis. These Included centralised control of tailings thickening and return circuit water distribution, centralised control of the crushing plant and use of the computer as a data processor for an on-stream analysis system for flotation slurries.

Jan 1, 1979

Africa is rich in natural resources, much of which remain untapped. Despite that, international mining companies have largely stayed away from the continent due to political instability in many countries, lack of infrastructure and the inability to gain control of mineral deposits. Today, optimism is growing concerning African mining. Many of its nations are moving toward privatization of their mining industries. They see it as a way to improve the lives of their populations and become politically stronger. Ministers from 22 African nations were Denver, CO in June for the World Bank's Multilateral Investment Guarantee Agency's Fourth Annual African Mining Investment Symposium. The three-day symposium drew more than 400 mining executives and government representatives. Foreign mining investment in Africa is on the increase. In 1996, international mining companies spent about $418 million on exploration. That is more than double the $190 million spent in 1994. Mining executives say the mining climate in Africa is improving because countries are privatizing the industry and rewriting mining laws that encourage natural resource development. They estimate that private mining firms now control about 80% of mining today. Mine development will help lift the living standards for Africans, the ministers said. The average income for ordinary Africans is about $500 a year. If this new mining boom continues, citizens of nearly all African nations will reap the benefits of better infrastructure and government services, as well as more higher paying jobs, the ministers said. They also issued a word of caution to mining companies attempting to join in the African boom. Concerns are being raised about the treatment of villagers and the environment. In the past, foreign companies would "behave about like colonial masters," said Gerald Ssendaula, natural resource minister for Uganda. Africa is in a different position now, he said. "Now we are solving our own problems." Mining companies must respect local communities or risk creating unrest that will threaten fragile new governments, said Akolang Tombale, chief geologist for Botswana. On the other hand, he said villagers must accept that mining development will benefit them. "They feel these are their natural resources. There must be a mutual interaction between the companies and the people."

Jan 1, 1997

By Ulf Marklund, Manfred Lindvall

Fighting the challenge of diminishing ore grades, low base metal prices and a changing pattern of ore supply, Boliden has now taken the second generation of the fully­autogenous grinding concept on stream, Using new design and a highly-developed process control system the benefits of conventional two stage autogenous grinding technology are obtained with a wide range of ore types. The APC grinding system has been developed further. A new design of the Boliden Pebble Extractor together with an advanced control strategy make the performance of the APC concept superior to all other grinding systems with any ore quality. The capacity and simplicity of the autogenous grinding concept is equivalent to the best SAG installations but the operational costs are up to 25 % lower than for SAG or other primary ball or rod mill systems. The concept is as flexible as conventional crushing and rod mill installations but investment and operating costs are of the order of 25 % lower. Also, from the metallurgical point of view, the different types of autogenous grinding system outperform all other comminution systems including SAG. From 1989 to 1991 four fully autogenous grinding sections have been installed at various concentrators at the Boliden company. Old crushing plants and rod and pebble grinding circuits have finally been replaced by highly productive and cost-efficient autogenous grinding equipment. Significant savings in operational costs have already been reported. Power consumption and maintenance costs have been reduced significantly. Productivity expressed as milled tonnes per operator has been improved. Metallurgical results have developed favourably.

Jan 1, 1992

By Heflin. L.

The Washington Metropolitan Area Transit Authority, WMATA, has constructed over 92 revenue miles of rapid transit facilities including some 14 miles of rock tunnel and 12 miles of earth tunnel. The system map is shown in Figure 1. During construction it is not unusual for contractor to encounter ground conditions resulting in major problems and extra cost. Problems such as major rockfalls and a "stuck" boring machine in squeezing rock are not unusual. In recent years, faced with additional tunnel construction projects, the Authority has sought newer tunneling methods which might be less costly. One new method which has been tried is NATM, the New Austrian Tunnel¬ing Method. NATM, which is applicable to both soft ground, mixed face and rock tunneling, relies on miners and comparatively small machines to excavate in conventional ways, but it is unique in its methods of obtaining "stand-up" time at the excavated face and its method of using shotcrete as an initial lining, frequently with a drainage system to reduce hydro-static pressure on the final lining. Lower costs result from use of a cast-in-place concrete liner, and from a reduction in the number of work operations at the mine heading which provides better daily production. WMATA has recently completed three twin bore tunnels constructed by NATM technology. The first was the Wheaton Tunnel and Section, followed by the tail track tunnel to total some 4200 linear feet cut through jointed rock up to 270 feet below ground surface, and the last was in soft ground at Fort Totten. A

Jan 1, 1993

By Robert J. Wise

The mine plan for an underground longwall mine plan usually requires a longwall panel conveyor that begins operation at its maximum length and gradually shortens over the life of the panel. Current mine plans around the United States require initial panel conveyor lengths of up to 4500 m (15,000 ft) and capacities of up to 3.2 kt/h (3500 stph). Because these conveyors are constantly being moved from panel to panel, their components must be as compact and light as possible, and the design must be flexible enough to be modified as new terrain and conditions are met. In the past, when drive horsepowers or belt tensions were exceeded due to conveyor length, a new flight would be added, including additional belt storage units. In some cases, this led to as many as three flights installed in a single longwall panel. As the longwall retreated through each flight, mining was required to stop during removal of the drives and storage units. This sometimes meant several days of lost production. Intermediate drive technology was developed to eliminate this excessive downtime and still keep conveyor belts, motors, pulleys and other components as small as possible. With intermediate drives placed along the carrying side of the conveyor, belt and motor sizes are kept as small as possible, and only one storage unit is needed. Most importantly, as the longwall retreats through a booster drive station, it can generally be removed in a regular downtime slot and no additional production time is lost.

Jan 1, 1993

By Pedro D. Lasota

Chile leads the world in copper production with an annual capacity nearing 2 Mt (2.2 million st). Most of the country’s copper production, about 74%, is mined by open-pit mining methods. Open-pit mining also accounts for a major portion of Chile’s production of other commodities, including iron, gold, silver and coal (Table 1). Chile’s mining boom began 10 years ago and is expected to continue through the end of the decade. From 1980 to 1990, copper production in Chile increased 48.7%. During the same period, gold production increased 303%, silver production increased 119% and coal and iron ore production increased 163.7% and 6.6%, respectively (Table 2). It is estimated that copper production will be in the order of 2.3 Mt (2.5 million st) by 1996, when new projects now under construction come onstream. Gold production could reach 35 t (1.1 million oz) and coal production could increase another 1 Mt/a (1.1 million stpy). Open-pit mining has played a significant role in Chile’s minerals production growth. The expected increases in mine operations will come about mainly through new open pits or expansions of existing surface operations (Table 3). However, the number of open-pit copper mines will decrease from 74% to 66% of the total number of Chilean mines. Gold mines will increase from 63% to 69% of the total, while coal mines will go from 41% to 59%. Most all of the present iron ore production is from surface mines and will continue that way.

Jan 1, 1992