Search Documents

By S. G. Malghan

Flotation is the primary method for copper minerals separation from porphyry ores. The need to process difficult-to--float porphyry copper ores presents challenges to engineers and scientists in several areas. This paper is concerned with summarizing generalized problems faced in processing porphyry ores and treatment methods to overcome them. Though some of the problems are interrelated, they are classified into three broad categories. The case studies of some of the successful applications of innovative methods to solve problems related to ore mineralogy, metallurgical aspects of ore treatment, and process variables show that quite often the problems are solvable by a judicious choice of flotation variables.

Jan 1, 1987

By J. H. Rowland, A. C. Smith, K. A. Teacoach

Current regulations for fire suppression systems in underground coal mines to protect conveyor belt installations have been in place since the Coal Mine Health and Safety Act of 1969 was enacted. Over time, the coal conveyer equipment being used and ventilation conditions underground have changed significantly, particularly the width of the conveyor belts and the use of belt air at the face. The effect of these new conditions on the effectiveness of suppression systems during a fire is not known. The National Institute of Occupational Safety and Health (NIOSH) conducted a study to evaluate the effect of air velocity, water sprinkler activation temperature and a limited water application time on the effectiveness of water sprinkler fire suppression systems to extinguish large-scale conveyor belt fires. The fire tests were conducted using both new and used 1.8-m-wide, fire-resistant rubber belt that met the Mine Safety and Health Administration (MSHA) flame-resistant requirement specified in Title 30, Code of Federal Regulations, part 18, section 18.65 (also known as the 2G test). Tests were conducted using standard response sprinklers with activation temperatures of 68° C and 141° C at air velocities of 0.5 and 5.1 m/s. Two tests were conducted at both air velocities for each sprinkler activation temperature, one using a new belt and one with a used belt. The results showed that the suppression system was able to suppress the fires in ten minutes to the point that a miner could extinguish it with a fire hose. However, in several of the tests, the fire reestablished itself a few minutes after the sprinkler water supply was cut off and quickly grew out of control. This report discusses the large-scale experimental configuration, the installation specifications of the fire suppression system and the results and conclusions regarding the effect of air velocity, sprinkler activation temperature and limited water application on the suppression system performance.

Jan 1, 2010

By Zvonimir Jam?ek

In Rudarski Institut Ljubljana (RIL), i.e. Ljubljana Mining Institute, we have developed CADRIL, a smaller CAD package which purpose is to overcome the difficulties by introducing Computer Aided Design in our mines. Program CADRIL is a graphics shell for several computer applications in mining. With the basic version of CADRIL all 2D working maps for daily use can be produced. Inserting different program blocks into CADRIL we get versions MAPRIL, TAHRIL, SECRIL and so on. The main purpose of all versions is graphics design. The main and most innovative feature of CADRIL is the screen four-word command menu. Not having pull-down or tablet menus is the speciality of this program. CADRIL contains 500 achievable commands. Each of them can be composed by choosing two to four expressions stored and shown in a specific four- column menu, sorted as objects functions, parameters and modes. Thus all commands are immediately accessible. As a result of its plainness and adaptability to the present working methods of mining engineers, CADRIL quickly attained a good reputation in our mines.

Jan 1, 1992

By James F. Albus, Vincent C. Grimshaw

High pressure fluid energy grinding, or jet milling, is a versatile method of continuously fracturing solids into fine particles to gain substantial increases in exposed surface area Applications in industrial minerals grinding include calcium carbonate, talc, barytes, mica, diatomaceous earth, bauxite, rutile, coal, kaolin, sepiolite, diamonds, etc The basic principles can be extended to provide continuous drying and delivery of discrete par¬ticles from a wet process slurry The main design and operational features of jet mills and dryers are described, relating energy consumption for both air and steam milling and hot air drying techniques Mean particle sizes in the order of 1 micron are achievable from pre-milled feeds, or maintained from similar slurries in the drying mode Aspects of feed preparation and multi-stage processing are discussed

Jan 1, 1983

By John A. Herbst, Kuang Y. Lee

Coarse particle size measurement is essential for the automatic control of a size reduction process like crushing or SAG milling in order to achieve optimal process performance. However, the on-line size measurement of coarse material is not easily obtained due to the problems of material handling and sample statistics. A technique based on advanced image analysis and quantitative stereology has been successfully developed and tested in a pilot scale setting. The chord length distribution of coarse particles on a moving conveyor was measured with an image analyzer and then transformed to the mesh size distribution with a stereological model and a special numerical method. Some test results as well as the technique's industrial suitability and limitations of this method are also discussed.

Jan 1, 1992

By J. C. Cawley

Improvements in today's maintenance practices are mandatory as more complex and productive machines evolve in the mining industry. By keeping machine reliability high through improved maintenance procedures, overall mining costs can be reduced. The Bureau of Mines is investigating diagnostic maintenance systems for underground mining machinery. A hydraulic expert diagnostic system and an electric motor predictive diagnostic system have been designed and installed on a Joy 16CM continuous miner. An electrical diagnostic system has been designed and installed on a Joy 14CM continuous miner. Each system is functionally described and the relative merits of expert diagnostic systems versus algorithmic diagnostic systems are discussed.

Jan 1, 1992

By R. V. Ramani, R. Natarajan, A. Bhattacherjee

Industries in general, and mining in particular, have become safer than ever before. However, there is a need to increase the search for the causes of mining work-related injuries and to contribute to their reduction, as required, through job redesign, work procedures and worker training. Mine accident and hazard control must be practiced in a manner consistent with the overall objectives of the mine management, which include the optimum allocation and effective utilization of the resources. The purposes of this paper are to: • present a set of analytical tools to analyze injury experience data. • apply these tools on a case study example, • discuss the results of the case study, and • identify the application limitations and the future research needs.

Jan 1, 1993

By John A. Herbst, William T. Pate, A. Edward Oblad

Dynamic optimization is a cost-effective means to increase production or improve product quality in a plant. Several model-based approaches to dynamic optimization of mineral processing operations have been developed and implemented in plants. This paper reviews the phenomenological models that are the basis for dynamic optimization and the alternative methods of mathematical optimization. These methods range from theoretically complex and costly to implement to intuitively comprehensible and readily implemented.

Jan 1, 1990

By W. Pariseau, J. Goris, S. R. Dismuke

Ore at the Magmont mine in southeast Missouri is extracted by the room-and-pillar method on two and sometimes three horizons. In 1991, a plan was formulated to recover high-grade ore in pillars using cable halts to accommodate spans of more than 27 m (90 ft ). A test area was selected and a recovery plan developed. A cooperative rock mechanics study was established by Cominco Metals, the US Bureau of Mines and the University of Utah. When initially opened in 1968, the planned production rate was about 910 kt/a (1 million stpy). Due to declining reserves, the production rate was decreased in November 1992 to 570 kt/a (630.000 stpy). Pillar recovery now accounts for about 40% to 50% of the mined tonnage. This method plays a vital role in allowing Magmont to continue to operate.

Jan 1, 1996

By P. Kolettas

The development of novel methods for the investigation of the subsoil contributes to the improvement of geotechnical research, enhances the obtained geotechnical characterization and may reduce the investigation cost by reducing the number of required tests. Non-destructive testing methods, performed either in situ (i.e. electrical tomography, seismic refraction, etc) or in the laboratory can provide initial data and perhaps estimates of rock/soil properties. This study focuses on the development of rock material properties and/or characteristics based on non-destructive laboratory testing of a number of stones, ranging from porous (bioclastic) limestones to impervious marbles. Seismic velocity measurements as well as attenuation signals were digitally recorded using a digital oscilloscope. Data were processed using a novel technique of spectral analysis available through special Matlab packages employing Fourier transform methods. More specifically, the NFFT (Non Equispaced Fourier Transform) transformation was applied to seismic waves traveling through the subsoil using the Autosignal program (by Seasolve) and the Specgramdemo program included in the Signal Analysis toolbox of Matlab 6.5 (Mathworks). Results indicate a definite relationship between the frequency content of the signal and the rock type as well as the degree of saturation of the specimen.

Jan 1, 2008

By Hayward B. Oblad, Gary F. Meenan

Two optoelectronic detectors were developed by CONSOL R&D for fine coal processing applications. One sensing device is used to estimate the amount of fine coal in the solids fraction of the froth flotation tailings slurry. The other probe, based on similar technology, is capable of measuring sol ids concentrations as high as 10 weight percent in fine coal slurry streams. These patented optoelectronic sensors are installed in several CONSOL coal preparation plants and are an integral part of the fine-coal control systems.

Jan 1, 1993

By Yoginder P. Chugh, M. Silverman

Premining investigations involve the determination of roof, floor, and coal seam characteristics to delineate areas of troublesome ground control prior to development of a mine. Data obtained can be useful in mine design, equipment selection, estimation of face productivity, development of ground control plans and assessing ground control costs, and in conducting feasibility studies and financial analyses. This paper discusses 1) the causative factors associated with ground instability, 2) how useful data can be obtained for these factors during premining investigations, and 3) analysis techniques to delineate probable areas of ground instability.

Jan 1, 1982

By Xiangze Shu, Yuzhong Xing

All programs used to optimize main fan nowdays have to be run on the large and medium- sized computers. With a lot of array elements, complex processes, low convergence speed and large storage, these programs are both time consuming and difficult to be used in the micro computer. This program uses two languages (dBASEIII and BASICA) to calculate the network and to choose the fan respectively. It allows user to compare and choose the parameters of various kinds of fan and to transfer the selected fan parameters to the master program by a data communication system. Then the user can get the air quantity, the air pressure, the power and the efficiency of the main fan. The advantages of this program arc as follows: 1. It can be run on IBM-PC or compatible micro computer. 2. It can select a fan more quickly and less time consumingly. 3. It can choose desired one or a set of fans according to user's requirements. 4. It is suitable for the research institutions and coal mines.

Jan 1, 1991

By D. Belin

Treatment of dilute acid mine drainage and similarly polluted water is becoming increasingly complicated. The pressure of economics is now exacerbated by legislation which classifies as hazardous waste the precipitates from conventional lime treatment plants. Since acid mine drainage invariably contains sulfate ions, one solution is to use anaerobic Desulfovibrio type bacteria to reduce the sulfate into sulphide ions which could then be used to precipitate out the heavy metals. Results are presented for both batch flask cultures and continuous column tests. Compost was used as the bacterial substrate in the column test which simulated heaps. Conditions changed from aerobic to the required anaerobic deep in the columns. Polluted feeds (up to 700 mg/l zinc) gave effluent containing well below I mg/l zinc over extended periods. Direct transfer of sulphide ions through a stream from an isolated container of bacteria is a good alternative.

Jan 1, 1991

By R. Karl Zipf, Z. T. Bieniawski

Based on the premise that understanding the fundamental mechanics of fine fragment formation in coal will lead to reducing coal dust problems in mines, a thorough study of the mechanics of crack propagation in coal was undertaken. Two approaches were considered in an attempt to understand and quantify the fracture process as it relates to fine fragment formation. In one approach, theoretical models are used which describe the size of the fracture process zone which may relate to the amount of structural damage and fine fragment formation on the new crack surface. The other approach is based on the relationship between crack tip stress intensity and new surface appearance for mixed mode crack propagation. Preliminary observations with a scanning electron microscope support the premise that fine fragment formation is related to fracture surface appearance and fracture initiation conditions. An experimental program designed to supply the input parameters for these approaches is presently underway. The experimentation features mixed mode fracture toughness testing, using a special mixed mode testing rig, and fracture velocity measurements with a crack propagation gage. The interpretation of this data via the approaches discussed will provide further under- standing of the mechanics of fine fragment formation in coal.

Jan 1, 1986

By M. Polat, S. Chander

Many models have been suggested in the past to obtain a satisfactory fit to flotation data. Of these, first-order kinetics models with a distribution of flotation rate constants are most common. A serious limitation of these models is that type of the distribution must be pre-supposed. Methods to overcome this limitation are discussed and a procedure is suggested for estimating the 'actual' distribution of flotation rate constants. It is demonstrated that the classical first-order model fits the data well when applied to coal flotation in narrow size-specific gravity intervals. When applied to material which is fractionated on the basis of size alone, the use of three parameter models, which were modified from their two parameter analogs such as rectangular, sinusoidal, and triangular, gave most reliable results.

Jan 1, 1995

By V. Srajer

Operations research includes the application of systems analysis to mining operations, the acquisition of field data and the creation and verification of computer models of these operations. These activities result in the generation of computerized mine planning tools which have a firm base-in observational facts. The Surface Mining Laboratory of the Canada Centre for Mineral and Energy Technology (CANMET), in Devon, Alberta has been engaged in operations research activities since 1982. The work includes computer simulation of truck/shovel, continuous mining equipment and dragline operations. Other examples include cooperative programs with industry (such as the demonstration and evaluation of an integrated truck management system), the development of a device to measure off-highway truck rolling resistance, and an automated remote data transmission network. The presentation outlines existing and proposed research projects of the Operations Research group.

Jan 1, 1989

By G. A. Kosick, L. Kuehn

The design of an information management system (IMS) for a mineral processing plant requires prior consideration of many factors, which can be broadly categorized into two domains, process plant considerations and IMS considerations. The process plant considerations include: plant characteristics, management and personnel issues, existing organizational standards and policies, and the level of existing hardware and software systems. The IMS considerations include: system functionality, system sizing and desired performance, hardware components, software components, and system support issues. All of these aspects must be addressed in order to achieve a functionally successful and cost effective system. The purpose of this paper is to lay out these design issues and, in doing so, to provide process engineers with a guideline with which to tailor a system that is best suited to their specific application. The paper is completed by presenting an approach that has been used in two Canadian concentrators. Both of these plants have incorporated MillEX, a software system designed specifically as the central component of a mineral processing IMS.

Jan 1, 1993

By H. Nematollahi

The comminution laws The grindability of the ores or minerals is an important factor that could not be deduced from their mineralogical characteristics (Testut, 1958). Many theories have been proposed to determine the amount of work required in a comminution operation as a function of the nature of material, size and shape of the minerals before and after of comminution. The most important laws are proposed by Rittinger, Kick and Bond. According to Rittinger (1867), the work is directly proportional to the new surfaces produced during the comminution. Kick (1885) believes that the work needed to produce similar modification is proportional to the volume or mass of the material. Bond, during his 25 years of experience and research, reached to the conclusion that on the average the energy required for a known comminution is between the Rittinger's and Kick's laws (Bond, 1952). According to Bond's Third Theory, the work input is proportional to the new crack tip length produced during the particle breakage, and equals the work represented by the product minus that represented by the feed.

Jan 1, 1994

By Richard Hogg, Heechan Cho

Investigations of long-time grinding of fine quartz (to about 80% passing 0.35 pm) in a 0.6 liter stirred-media mill are described. Breakage rates and primary breakage distributions have been determined based on extensive characterization of the ground products by laser scattering/diffraction and gas adsorption. The results indicate that, while there is qualitative similarity between the breakage parameters for ultrafine and conventional (coarse) grinding, there are important, quantitative differences. In particular, it is found that primary breakage distributions become significantly narrower in the submicron sizes. The trend can be described using double-truncated log-normal distributions in which both a maximum (breaking) size and a grind limit are specified. The breakage distributions become progressively narrower as the size being broken becomes finer. Breakage rates follow a typical, consistent pattern in which the rate decreases with size according to a simple power law. Further decrease in the rates seems to occur after very long grinding times when the entire mill contents become finer than about 1µm. The effect is explained as a result of changes in the rate/size relationship in the submicron range.

Jan 1, 1995