Search Documents

By S. W. Kan, M. G. Kakarkis, J. Zelanco

Grouting has been used in underground mining for more than 20 years. Chemical grouting is often used as a remedial measure when the implemented ground-control program is unable to completely prevent structural failures or when there is a need for preventing a structural member from unraveling. The utilization of polyurethane grout is restricted by its limited range of physical and mechanical properties. To overcome some of the drawbacks of polyurethane, research is being conducted on a newly developed polyester based grout. The polyester resin, identified by Sandvik as Strata Grip, provides a number of features, including variable gel times and a much-reduced chemical hazard. Equally important are the mechanical properties of the product. The strength and deformability of any chemical grout must be compatible with the intended purpose of grouting and the expected deformation of the rock that is to be grouted The assessment of the mechanical properties of polyester grout is the focus of this work. Field experiences and laboratory research defined the properties of an effective grouting material. Experimental results indicate that the polyester grout meets or exceeds the recommended properties for many injection applications. Furthermore, the results suggest that the ability to adjust mechanical properties via resin formulation has the potential to expand the applicability of chemical grouting in ground control.

Jan 1, 1999

By K. E. Hjelmstad, W. H. Pomroy

In the event of fire underground, it is essential that all miners be warned as quickly as possible. With mine air rapidly depleted of oxygen and contaminated with smoke and toxic fire gases, any delay in the warning signal could have disastrous consequences. Unfortunately, present mine fire warning systems, such as stench, audible or visual alarms, telephones, and messengers, are often slow, unreliable, and limited in coverage. Recent research by the US Bureau of Mines has established the feasibility of ultralow frequency electromagnetic signaling for underground mine fire warning. Infield testing completed thus far at five mines, signals of from 630 Hz to 2000 Hz were transmitted through rock up to distances of 1645 m (5400 ft) to a pencil-sized ferrite-core receiving antenna and intrinsically safe receiver circuit. Theoretical analysis indicates a capability to transmit effectively for distances in excess of the maximum depths of most American mines, which is about 900 to 1000 m (2950 to 3280 ft) . The prototype system uses off-the-shelf components and state-of-the-art technology to ensure high reliability and low cost. This technology would enable simultaneous and instantaneous warning of all underground personnel, thereby in- creasing the likelihood of successfully evacuating a mine during a disaster. This report discusses the theoretical basis for through-the-rock ultralow frequency electromagnetic transmission, design of the prototype transmitter and receiver, and the results of in-mine tests of the prototype system.

Jan 1, 1991

By William H. Schiffbauer

Research is being conducted toward making underground mining equipment autonomous. This will facilitate improvements in safety by relieving workers of dangerous tasks and will increase production by providing more accurate control with less down time.. A Bureau of Mines developed microcomputer network has enhanced this research by permitting a group of diverse computers to interact with a mining machine as well as with each other over a common data link. The network is composed of specially integrated off-the-shelf hardware and industry-standard operating system and programming languages. Using the network, researchers can conduct various experiments with the mining machine using a diverse group of intelligent sensors, computers, and microcontrollers. Descriptions of the mining machine, the mining machine control computer, control algorithms, -the microcomputer network architecture, and communication protocols are discussed.

Jan 1, 1989

By W. Stahl, K. Keller

In addition to classifying bulk material, vibration screens are commonly used in dewatering. However, the lack of a comprehensive physical theory of dewatering often leads to difficulties in the design and operation of the vibration screens. First, in this report, the dewatering of bulk material are shown based on a physical model. Because of tile oscillatory motion of the liquid in the bulk, the inertial force of the accelerated liquid and the dripping of water out of the bulk or screen must be taken into special consideration. The physical model put forward shows the effect of the various operations parameters of dewatering screens. A comparison between dewatering theory and practice are shown by measurements using coal, limestone, etc. Dewatering measurements conducted on a vibration screen demonstrated that different vibration frequencies and rates of acceleration lead to different residual moistures. Finally, the possibility of improving vibration dewatering is described.

Jan 1, 1998

By Thomas D. Kaufmann

Whether pursuing hedging or speculative strategies, gold miners can increase sales revenues 1 % to 6% by constantly pricing production forward. Unlike other commodities, gold futures prices are consistently higher than spot prices. A Colorado School of Mines study showed theoretically and empirically that in the 15 years since the price of gold was released from government control, the forward price for gold has been higher than the current price almost 100% of the time. The reason why Metal traders know that holders of metal earn a bonus selling forward when the metal is in "contango." "Contango" is a mysterious word that crept into the trading vocabulary a century ago. It designates a situation when the price of a metal on the futures markets is higher than the price in the immediate or spot market. If the spectrum of spot and futures prices remains static over time, the forward seller who has contracted at a higher than spot price can make a profit equal to the contango by redeeming his commitment at the lower spot price when the contract matures. Consequently, when a seller in a contango market hedges, he makes a profit on the transaction in addition to avoiding a price change risk. On the other hand, buyers of the metal who hedge in a contango situation will sustain a loss equal to the contango. Producers of gold, however, are sellers of gold. For most metals and oil, there is no inherent reason why futures prices should be higher than present prices. Buyers and sellers decide that the price of the commodity will be lower or higher than present values for a variety of reasons.

Jan 1, 1991

By C. L. Barron, M. L. Smith, K. A. Prisbrey

SAG mill throughput is often a bottleneck to increasing plant productivity. Improved size distribution control in the mill feed can be used to increase mill production. This can be accomplished by controlling blast fragmentation as a function of energy input and rock characteristics. Such an approach requires the integration of rock fragmentation and comminution modeling. The optimal mill feed size distribution is determined by adapting a population balance comminution model to a measure of rock hardness or fragility, which is also related to the rock fragmentation that is achieved by blasting. The relationship between the size distribution and fragility of the feed and the mill's product and the critical size in a SAG mill is examined.

Jan 1, 1994

By M. N. Brodie

The paper examines the requirements for electric power used in concentration and dewatering circuits, the effects of plant capacity and process type, the restraints imposed by the primary supply and applicable codes and outlines the procedure by which effective design is carried out.

Jan 1, 1986

By T. I. Probert, B. W. Burdett, L. B. Hales

Selecting a mineral processing control system from the multitude of offerings can be a formidable task. To assist the plant designer, the material in this chapter includes the advantages and disadvantages of different equipment types, configurations, and control strategies. Selection procedures are detailed, and the importance of each step in the design and selection process is explained.

Jan 1, 1986

By K. Burke, G. Zhan, A. Mayer

A cover with capi1lary barrier effects (CCBE) is being constructed an the AA leach pad at the Barrick Goldstrike mine near Carlin, Nevada. The purpose of the cover is to eliminate/minimize infiltration of meteoric waters into the leach pad. Laboratory and numerical analyses indicate that Carlin Formation siltstone (TCS), a locally available material, has the necessary hydrologic characteristics when placed on the leach pad to act as a CCBE. A pilot study was conducted on a mall-scale test cover placed on the AA leach pad to examine the cover performance under irrigated conditions. The preliminary test results demonstrate that the designed cover is capable of preventing meteoric water infiltration.

Jan 1, 2002

By Paul Clifford

The Florida Institute of Phosphate Research (FIPR) is an independent, state of Florida research agency. It was created in 1978 to conduct research to enhance the competitiveness of the Florida phosphate industry. The institute also conducts research to prevent, minimize or rectify environmental impacts caused by the industry. And it helps educate the public concerning phosphate-related technology and issues. FIPR is funded by a severance tax on the industry and is governed by a five-member board of directors appointed by the governor. FIPR's research is playing a role in enhancing the competitiveness of the Florida phosphate industry. Its technology research program seeks to improve surface mining and pipeline transportation while reducing the energy cost for pumping phosphate matrix. It is developing new and improved methods of beneficiation and fertilizer production. This includes new process flowsheets and on-line analyzers and process control methods. FIPR is also developing uses for the phosphogypsum byproduct of phosphoric acid production and evaluating the risks associated with its uses.

Jan 1, 1998

By L. B. Hales

Color video or digital cameras have been installed over flotation cells to monitor color, bubble size, froth movement, and other characteristics. These systems are designed so that the camera provides flotation performance information just as any other sensor might. Factorial tests have been run to monitor and measure the variation in froth characteristics as a function of flotation control settings. Ultimately, it is envisioned that froth image sensors can be used to monitor and control the flotation performance as effectively and for less cost than current analytical systems.

Jan 1, 1999

By J. E. Taylor

A detailed planning and design project has been undertaken at Callide Coalfields, as the first step towards implementing a fully integrated mine graphics system. The system, when fully installed, will support applications ranging from business graphics through to terrain modelling and computer-aided design. The conceptual design which will accomplish this is presented. The problems of retrospectively applying graphics standards to existing applications are discussed, and a practical solution outlined.

Jan 1, 1986

By E. Topuz

Mining equipment, like all other equipment, is subject to failure. Since most failures occur at random and are unexpected, corrective maintenance is usually more expensive and causes more down-time than preventive maintenance. In order to reduce the number of failures and thereby increase the availability of an equipment or system, preventive maintenance can be scheduled at predetermined points of time. The preventive maintenance scheduling policies presented in this paper utilize reliability and probability theories. They can be applied to various production bottlenecks where high cost equipment precludes having sufficient quantities of stand-by units.

Jan 1, 1982

By Richard V. Beck, Donald R. East, Jeremy P. Haile

In view of the increasing use of heap leach operations in the mining industry and the critically important performance of the leach pad liner in both the economic and environmental aspects of the design, it has become essential that the designer fully understand the factors affecting the performance of the liner. Minimizing the loss of pregnant solution through the leach pad liner is obviously of paramount importance to the economic efficiency and environmental compliance of the heap leach operation. Losses through the liner are a function of the hydraulic conductivity of the liner material and the hydraulic gradient across the liner. This applies to both natural and synthetic materials. The hydraulic gradient across the liner is a function of the build-up of solution above the liner, which in turn is determined by the permeability of the heap material, the slope of the liner, the drainage path length and the leachate infiltration rate. A relationship incorporating each of these parameters and their effect on the hydraulic head acting on the liner has been developed in terms of the Dupuit criterion, assuming one- dimensional flow with vertical accretion.

Jan 1, 1987

By Joseph M. Keane

Introduction The English word "sedimentation" is derived from the Latin verb "sedere" meaning to sink down. As a mineral processing unit operation, sedimenta¬tion has been defined as the separation of a suspension into a supernatant clear fluid and rather dense slurry containing a higher concentration of solid (Brown, G.G. 1960). Sedimen¬tation has been historically subdivided into thickening, which has the primary purpose of increasing the solids content of one of the thickener prod¬ucts relative to the feed stream, and clarification, which has the primary purpose of removing solids from the feed stream to produce a product essentially free from particu¬late matter. There is no absolutely precise distinction between these subdivisions and in certain applica¬tions, both objectives can be accom¬plished. Major Design Factors The capacity of conventional metal¬lurgical sedimentation devices is a function of slurry throughput and its attendant settling rate. Important factors, recognized by early investigators (Taggart, 1972), which influence the settling rate of a given metallur¬gical slurry include: Feed dilution or solids-liquid weight ratio Size and shape of the particulate solids Specific gravity differential between the solids and liquid phases Presence of electrolytes and/or flocculants Pulp viscosity Slurry temperature In addition to the foregoing histor¬ical factors, recent investigators have noted (Pearse, M.J., 1977) that other parameters which may have an influence upon settling rate and, thereby, thickener performance include: Method of flocculant application Particle size distribution Particulate wetting characteristics Feeding arrangements Rake speed and type Existence of convection currents Wind disturbance Evaporation All of the above factors should be examined and the effect upon thick¬ener performance brought about by manipulating the factor over the expected operating range should be determined if performance optimization is desired.

Jan 1, 1986

By Jerome C. Neyer

Within most of Canada and the northern third of the United States, the soils overlying bedrock are of glacial origin. Tunnelling in glacial soils presents numerous challenges to the contractor, including abrupt changes in soil type, boulders and glacial erratics, water bearing fine sands and silts, toxic or explosive gases, and glacial till. This paper examines the available techniques for geotechnical exploration in glacial soils; the relationship between subsurface conditions predicted by various techniques and conditions actually encountered during tunnel construction; and potential improvements in the planning and implementation of geotechnical explorations. Case histories of geotechnical exploration and tunnel construction in glacial soils are also reviewed.

Jan 1, 1985

By K. J. Reid, I. Iwasaki, T. Sabelin

Introduction Occurrences of platinum group minerals (PGM) in mafic and ultramafic rocks in association with Cu-Ni mineralization are well known. Yet for the Duluth Complex, a large body of dominantly mafic igneous rocks in northeastern Minnesota with significant Cu-Ni mineralization (Bonnichsen, 1972; Boucher, 1975; Watowich, 1978; Weiblen and Morey, 1980), little has been published concerning its platinum group element (PGE) contents and mineralogy. In a previous study of massive sulfide rock, sperrylite (PtAs2) was found in nickel arsenide and recovery of arsenide minerals by flotation has been investigated (Iwasaki et al., 1986; Ryan and Weiblen, 1984). Recently, an announcement was made of the discovery of significant quantities of platinum and palladium [peak assay values of 9 g/t (0.27 oz per st)] in an interval of a drill core with disseminated sulfide mineralization 16 km (10 miles) southeast of Ely, MN (Anon, 1985; Sabelin, 1985). This paper describes PGM from the Pt-Pd-enriched zone and evaluates their potential for concentration. Geologic setting The Pt-Pd zone occurs in the South Kawishiwi in¬trusion near its basal contact at 734 to 737 m (2408 to 2418 ft) depth. The South Kawishiwi is one of several minor mafic intrusions that constitute the western margin of the Duluth Complex near Ely, MN (Fig. 1). It is com¬prised of a 70.1- to 350.5-m (230- to 1150-ft) thick sul¬fide-bearing basal unit of troctolite with minor amounts of anorthosite, norite, picrite, and oxide layers overlain by a troctolite unit with interlayered anorthosite (Bonnichsen et al., 1980; Foose, 1984; and Foose and Weiblen, 1986). The basal unit, in which the Pt-Pd zone is found, is markedly heterogeneous in rock type, lacking any coherent internal stratigraphy, and shows evidence of both pre- and post-consolidation faulting (Foose and Weiblen, 1986). Geochemistry Chemical analyses were made on 0.3-m (1-ft) intervals of crushed drill core material (1/4 core, BX size) at 731.5 to 740.7 m (2400 to 2430 ft) depth and the results are presented in Fig. 2. The analytical techniques used were atomic absorption spectrometry for silver, chromium, copper, and nickel; a coulometric titration method for sulfur; and a combined fire assay-DC plasma technique for gold, palladium, and platinum. Figure 2 shows the significant enrichment of platinum and palladium at 734 to 737 m (2408 to 2418 ft) depth; it corresponds to a stratigraphic interval rich in oxide minerals. Average values for platinum and palladium contents over the 3-m (10-ft) interval are 2520 and 2580 ppb, respectively, or 5.1 g/t (0.15 oz per st) platinum plus palladium. Platinum plus palladium contents from individual 0.3-m (1-ft) intervals are as high as 9120 ppb or 9.1 g/t (0.27 oz per st) and average 7.4 g/t (0.22 oz per st) in a 1.5-m (5-ft) interval in the richest part of the zone. The Pt-to-Pd ratio is nearly 1:1 over the entire 9.1-m (30-ft) interval and the platinum and palladium correlate closely with chromium, which ranges from 1.9% to 5.3%. Copper, nickel, and sulfur contents for the drill core interval are also given in Fig. 2. In¬terestingly, the Pt-Pd high corresponds to a depletion in copper, nickel, and sulfur. Mineralogy of the Pt-Pd zone The Pt-Pd zone occurs within an oxide-rich zone or layer that consists essentially of oxide minerals, plagioclase, and olivine. The oxides may constitute as

Jan 1, 1987

By Thomas R. Kuesel

All engineering designs are based on assumptions regarding the behavior of the structure or facility being designed. These assumptions may be based more or less heavily on theory, but are credible only if verified by observations of field performance. Dr. Peck's "State-of-the-Art" paper has described the semi -empirical process of soft ground tunnel design, emphasizing the importance of records of field performance of actual projects constructed under a variety of conditions. This paper will present the principal results obtained from measurements made during construction of the soft ground tunnels for the San Francisco Bay Area Rapid Transit System. SCOPE The BART System comprises 75 route miles, including 14 miles of soft ground tunnelled subways in San Francisco, Oakland, and Berkeley. All tunnels are single-track sections, approximately 18 feet in diameter. Usually there are two parallel tunnels at the same level, but under Market Street in San Francisco there are four tunnels (two over two), and there is also a three-track section (two over one) in Broadway, Oakland.

Jan 1, 1997

By Richard Lovat

INTRODUCTION Soft ground tunnels may be above the ground water table or they may be subaqueous. The ground may be clays, silts, sands, gravels, glacial deposits, boulder tills, and any of these in any combination. Because of the relatively low strength and deformability of soils, difficulties often arise in soft ground tunnelling. These soil characteristics and resultant tunnelling difficulties, have had a direct influence on the development of "Lovat" Tunnel Boring Machines. We have been required to recognize and adapt to unusual ground conditions and to follow through with design, fabrication, and field maintenance to ensure dependable, trouble-free operation. The basic "Lovat" machine is a fully shielded, wheel-type with the cuttinghead driven by a monorace type bearing with gear drive incorporated in the bearing. Mechanical innovations have been added to the basic machine which complement the resources of manpower, equipment, and materials available to the contractor for a specific operation. FULL FACE SUPPORT The installation of hydraulically operated closure doors or flood control doors, at the cuttinghead, is one of the early "Lovat" technical innovations. Flood control doors provide full face support in running or flowing ground. In water bearing sands and silts the excavated material can

Jan 1, 1981

By Bruce W. Cavender, Brian L. Granger

The leaching characteristics of non-homogeneous ores have traditionally been difficult to assess in laboratory tests. A result of the large sample size necessary to ensure representativity, this difficulty is most acute for ores containing nuggets or other irregular occurrences of precious minerals. Consequently, small-scale leaching tests are often regarded as indicative rather than conclusive. The predictive nature of leaching tests can be improved by applying the experimental design concepts of blocking and randomization. In the case of column leaching, experimental 'blocks" are constructed with the same number of columns as there are separate test conditions. These blocks are treated identically throughout the test, with differences between columns within each block being the variables of interest. To maximize the uniformity of the blocks, randomization procedures are employed in the preparation of the sample and conduct of the test. The initial ore sample is screened and individual column charges composited from randomly selected increments from each size fraction. The leaching order, daily solution analyses, and processing of leach residues are similarly randomized. The observed differences in leaching performance between the columns in each block are compared to determine the over-all outcome of the test. A statistical analysis using t distributions gives a quantitative measure of the reproducibility of the outcome.

Jan 1, 1995