Search Documents

By Gordon M. Pugh, David G. Rasmussen

INTRODUCTION Shrinkage stope mining can be employed in steeply dipping veins where both the wall and the vein material are sufficiently strong to stand with only minimal ground support. Shrinkage stope mining takes advantage of the swell in volume produced in breaking in-place ore. This expanded volume of ore is allowed to occupy part of the mined-out vein, and in so doing provides ground sup¬port and a working surface for the miners. Only enough of the ore is drawn after each stoping cut to allow work¬ing room. Not until the entire mining block has been broken is the full amount of broken ore drawn from the stope. DEVELOPMENT PRACTICES FOR SHRINKAGE STOPING The vein is developed into stoping blocks, each of which is 76 to 91 m (250 to 300 ft) in length and 61 m (200 ft) between levels. Level development, described later, is either on the vein or parallel to it with crosscuts periodically driven over to the vein. There are usually two exits from each stope. The first entry is a raise at one end driven either conventionally by raise climber, or by a raised borehole. Present practice is that this raise, put in from level to level, is either a 2.1- x 2.1-m (7- x 7-ft) Alimak raise or a 1.2- to 1.8-m (4- to 6-ft) diam borehole. Either raise system will require pro¬visions for an ore chute carried with the stope to the haulage level or the scram drift. At 9- to 12-m (30- to 40-ft) vertical intervals, dogholes are developed from the raise so that when stoping breaks back into these dogholes, timber or steel sets and necessary service facilities can be installed. The second entry to the stope may be either a similar raise at the stope endline, or more economically, a cribbed raise carried with the stope. As previously stated, development of the ore block is achieved by either drifting on the vein or by paralleling the vein with a footwall lateral and then crosscutting over to the vein at specified intervals. In the following discussion, three basic cases are illustrated in Figs. 1, 2, and 3. In Fig. 1, development is in the footwall by a 3- x 3-m (10- x 10-ft) trackless lateral. A heading is also driven on the ore and taken either full width or driven a standard size and slabbed to the vein width. Approxi¬mately 9-m (30-ft) long crosscuts on 7.6-m (25-ft) cen¬ters are driven from the lateral to the vein. For ease in muck handling they are usually put in on a slant rather than at right angles. A single orepass, located off the lateral and in the center of one stope block, can serve not only that stope, but also one on either side, up to a tramming distance of not more than 137 m (450 ft). Raises are put at the stope endlines on 91-m (300-ft) centers. The back of the vein is shot down and just enough broken material is drawn off to permit access for men to work off the broken ore. Development in Fig. 2 progresses by driving a 3- x 3-m (10- x 10-ft) trackless heading on the footwall side of the vein. The ore block is delineated by raises on 91-m (300-ft) centers. Crosscuts are again driven on 7.6-m (25-ft) centers over to the vein. Approximately four rounds are then taken up to the vein and each round is successively belled out so that all the crosscuts (pockets, in this case) connect. In this development, as opposed to that in Fig. 1 where there were no belled

Jan 1, 1982

By John E. Urbanic, William D. Faulkner, Robert W. Ruckel

Guidelines are presented for the selection, handling and regeneration of activated carbon used in gold recovery operations. The guidelines are based on Calgon Carbon Corporation's own investigations and experience gained in working with gold mine operators all over the world. Gold adsorption rate and adsorption capacity are shown to be independent variables thereby requiring testing of both properties when selecting activated carbon. Means of measuring these properties are provided. Historical activity tests on activated carbon are shown to be minimally useful in selecting carbon for gold recovery. Proper thermal regeneration techniques to maximize recovery of adsorption rate without weakening the carbon structure are suggested. Simple positive means of measuring efficiency of regeneration are presented. The subject of hardness measurement as a predictor of "in process" abrasion is discussed. The cost/benefit issue of carbon activity level is addressed.

Jan 1, 1986

By K. C. Carriere

INTRODUCTION The purpose of this paper is to introduce the reader to basic control strategies for solid/liquid separation in mineral processing and to indicate some of the implementation difficulties to be encountered, without becoming overly involved in details of process, equipment or software. It is assumed that the reader has some familiarity with control systems and with dewatering processes, since exploration of these topics would require considerably more length. The paper is organized into three parts: first a general discussion on the need for control of dewatering processes and of the general criteria involved, next a more detailed elaboration on control strategies for the various unit operations, and finally a case study showing a specific approach towards such a project. Motivation & Objectives The justification for implementing any control system in an industrial plant is to improve operations and thereby to increase profitability. Without this motivation, the system will likely be perceived as unnecessary and will decline into disuse, an expensive and troublesome monument to someone's ill-conceived ideas. However, when a control strategy is correctly conceived, implemented and integrated into operations, it can provide significant advantages in operating ease and efficiency, and a handsome return on investment. In general terms, the objectives in establishing a control system are: • stabilization of process disturbances maintenance of product quality • maximization of throughput • dearer definition of process • protection of personnel and equipment A successful control strategy must address at least some of the above criteria. However, the most important requirement is a commitment on the part of plant personnel and management to start up, operate and maintain the system, and to upgrade it to reflect current process status and operational philosophy. Process Applications In this paper, control strategies will be explored for the most common methods of dewatering of mineral pulps. These unit operations include: drying, centrifuging, filtering and sedimentation. While the first three are important, they do not tend to be as complex as sedimentation, and thus will not be as exhaustively treated. Sedimentation is very widely applied, not

Jan 1, 1986

By David J. Starbuck

For small precious metals mining to show a comeback a different perspective must be taken than that of larger mining companies. This perspective must be much the same as that of past successful smaller mining enterprises such as when the US had a need for Uranium. Abandoned mines and environmental concerns in older mining districts have discouraged many from entering with the attitudes of why try there if so many unsuccessful mines exist. A small mining venture can be successful there but must have a "think smart'' attitude. There must be a thorough understanding of deposits, utilization of advanced technology and a properly managed mining operation. "THINK SMART" MINING The small mine operator is usually looking for small high grade deposits, consequently, long term success depends on a series of small successful mining operations. The small miner must succeed right-off or credibility and future project funding will suffer. No veteran of even a few years in the mining industry needs to be told that a dollar spent on production today fails to yield as much as it once did. More efficient equipment and techniques have helped soften the problem, but there is little likelihood that a mining company can do much to control inflation, wages, regulations, or grade. That leaves the small miner to "think smart" as one area where operating dollars can still be stretched to produce more than they presently do (Gardner. 1981). In the planning stage of a mining venture, when most options are still open, the main controllable elements are market timing, deposit selection, cutoff grade, mining method, mine design, mining sequence, rate of production build up, process design, project financing structure, project management, and project ownership structure. During planning, optimum criteria can be established for each of these. Once a mine is in production, these options are foreclosed or at least severely constrained. The more thought given to a mining program using all information available the less the risk of encountering disabling surprises. Thus the intent of this paper is to suggest the "think smart" attitude most small mine operations use for long term success. If one looks at a number of successful mining ventures, whether large or small, there is a general logic most have followed to be successful. They have used proven exploration, mining and processing techniques along with economic evaluation and experienced personnel to improve their odds. LOGIC IN DEVELOPING A FEASIBLE VENTURE Most successful small mine ventures achieve positive cash flow as quickly as possible by seeking out those deposits which require the least time and expense on activities leading up to production. To do this they look for deposits that are the most accessible, easily investigated, mined and processed with the cheapest fundamental methods. The general sequence of events starting with district selection are deposit selection, preliminary feasibility, exploration, detailed economic feasibility, mine planning, development and production. Each successive step becomes more costly requiring intermediate decisions along the way. District Selection Small operations should look for known deposits which favor the occurrence of the type deposit sought rather than efforts in unproductive areas. Known deposits in developed areas have some advantages over remote areas: 1. More alternative methods of transportation are available. 2. A larger stable work force is available. 3. The area is usually more pro-mining. 4. Power, water, housing, technical services, skilled services, schools, recreation and shopping are available.

Jan 1, 1987

By D. S. Cavers

INTRODUCTION This paper discusses aspects of rock engineering applicable to surface gold mines. Discussion particularly centers on areas in which rock mechanics can enhance the mine productivity or profit- ability. Methods of analysis are discussed briefly but for more detai1s the reader is referred to the appropriate references. A team approach to the overall design of the pit generally pro- duces a better result at an overall lower cost. In particular, money is wasted by asking for a "report on slopes" and then input- ting this slope angle into a pit design and economic analysis study without further reference to the geotechnical engineer. Pit slope angle depends on slope orientation, location, pit shape, pre-existing discontinuities and mining methods. Preliminary slope angles can be produced but optimization depends on ongoing inter- action between the mining engineers, geologists and geotechnical engineers. This interaction can a1 so substantially reduce overall design time which may be critical in bringing remote plays into production. Most surface gold mines in North America are in igneous or metamorphic environments. Rock mechanics aspects discussed in this paper will be discussed with reference to these environments al- though most of the principles and comments are applicable to sedimentary environments as we1 1.

Jan 1, 1987

By David L. Gefvert

A general review of the role of cationic flotation reagents in the beneficiation of phosphate, iron, and potash ores. The three major types of cationic collectors-amines, ether amines, and condensates will be compared and contrasted. The effect of particle size, water chemistry, and water temperature on the choice of cationic flotation reagents for each industry will be discussed.

Jan 1, 1986

By R. M. Rowe, A. K. Bhasin, D. Malhotra

Introduction Most primary molybdenite producers use a selective flotation process in which molybdenite is floated from the ore while other sulfide and nonsulfide gangue minerals are depressed in the same step. The process was developed at the Climax mill. Reagents used in the rougher flotation stage include vapor oil (collector), syntex (surfactant), pine oil (frother), and occasionally sodium cyanide and Nokes reagent (depressant). Rougher concentrate is upgraded by cleaner flotation to produce market-grade molybdenite concentrates. Reagents used in the cleaner flotation stage are Dowfroth 250, vapor oil, sodium cyanide, and Nokes reagent. The development of the flotation reagent scheme at Climax and the role of the reagents have been well described by Born et al. (1976) and Malhotra et al. (1976, 1977a, 1977b, 1977c, 1980). The hydrocarbon collector, vapor oil, accounts for approximately 50% of the total molybdenite flotation reagent cost. Because vapor oil sources are limited, and the cost of vapor oil has increased significantly over the last decade, several studies have been done to evaluate alternate oil-based collectors and/or blends of collectors that would produce similar metallurgical results at a reduced cost, or increase the overall molybdenite recovery at the same cost (Smit and Bhasin, 1983; Hahn, 1969; Smith and Bhappu, 1971). The approach taken in the present study was to evaluate alternate nonoil-based collectors and collector systems that are less expensive than vapor oil. A series of potential nonoil-based collector classes were identified and evaluated in the laboratory against the current collector system. The metallurgical performance of these collector classes was related to their chemical structures. The results of this study are discussed. Collector classes A survey of sulfide mineral collectors was performed with the objective of identifying and selecting potential collectors for molybdenite flotation. The available reagents were categorized into 10 general classes. Table 1 summarizes these collector classes, their chemical formulas, the manufacturers, and selected commercial collectors in each class that were evaluated in the present study. Experimental procedure A Climax ore sample, assaying 0.3% MoS2, 2.2% FeS2, 0.007% Cu, 0.003% Pb, and 0.03 oz per ton Ag, was used for this study. Standard laboratory rougher flotation test procedure involved grinding a 2-kg ore charge in a rod mill at 60% solids. Reagents were added to the rod mill including a collector, syntex (0.005 kg/t), pine oil (0.03 kg/t), lime (to adjust pH to 8), and sodium silicate (0.15 kg/t). The ground pulp was transferred to a 1000-g cell, and flotation was performed at 35% solids and 1800 rpm using a Denver D-1 flotation machine. Concentrate was collected for a flotation time of six minutes. The general approach used in the present study was to substitute the nonoil-based collectors at two to three different dosage levels (0.01 to 0.15 kg/t) for vapor oil in the bench-scale, open-circuit rougher flotation tests

Jan 1, 1987

By T. H. Dubaniewicz, J. E. Chilton

The U. S. Bureau of Mines is investigating the application of fiber optic technology to methane and carbon monoxide monitoring. A methane monitoring system is described that is based on differential absorption of infrared light. It can detect concentrations as low as 0.2% and as far away as 2 km via fiber optic cable. The upper range is 100% methane. The system requires no electrical power within the mine so it should operate safely under mine disaster conditions. A hybrid carbon monoxide monitoring system is described that combines a low-powered electrochemical cell with fiber optic telemetry. Testing has shown the system can operate maintenance- free for several months.

Jan 1, 1992

By J. Patrick Powers, Arthur B. Corwin

Modern improvements in hydrogeology make it possible to predict with good reliability the performance and cost of ground water pumping systems in many tunneling situations. The testing and analysis techniques are presented. Data from the Buffalo NY LRRTS (1978-1980) illustrate the successful application of the technique for tunneling in rock. Data from the Red Hook Interceptor Tunnel in Brooklyn NY (1978) illustrate the application in soft ground. The Red Hook project also illustrates concerns for the side effects from dewatering, such as ground settlement and damage to timber structures. At Red Hook protective measures included compressed air, artificial recharge and controlled dewatering. Given the uncertainties of the underground, the possibility of unexpected situations must be considered. A hard rock sewer tunnel in Atlanta, Georgia (1982) illustrates an unexpected problem, and the emergency measures used to solve it.

Jan 1, 1985

By David D. Gallagher

Customer demand for greater efficiency and reduced operational costs on modern overland conveyors has focused attention on the conveyor belt's rolling resistance properties. Studies have indicated as much as 60% of the power losses on a long horizontal conveyor can be attributed to the indentation of the pulley cover rubber as it passes over idlers. This paper will compare tan delta values of different compounds with large scale rolling resistance test data from the University of Hannover. Results will then be compared to actual power consumption data gathered on several long overland conveyors using identical belt construction except with different pulley cover compounds. Concluding comments will be made indicating substantial operating cost differences based on the rolling resistance of the cover compound.

Jan 1, 2000

By R. Lai

This paper describes the application of a cyclonic flotation column (CFC) for coal cleaning. A CFC makes use of centrifugal force to create a density gradient in a column to augment the froth flotation process. In a CFC, a series of angular helical inserts is attached to the wall of a conventional column, and coal slurry is mixed with a series of impellers attached to a central shaft. The hydrophobic froth concentrates near the center shaft and moves upward, while the relatively heavy hydrophilic particles concentrate near the wall and are guided downward by the helical inserts. The results of pyritic sulfur removal from an Upper Freeport coal during CFC flotation are discussed.

Jan 1, 2003

By Allan D. Fernie

Many long conveyors, 2 - 20 km plus, have been installed over the past 10 years. Conveyor belt life, depending on the conveyor length and material handled, will generally range from 10 - 15 years. To replace long conveyors splicing one or two rolls into a conveyor run on an intermittent basis can be prolonged in an operating system involving considerable downtime and scheduling problems. This paper presents some of the methods used to- date and highlights forward planning for such an event. Special belt handling equipment required and the execution of a belt change operation are described in detail. Wright Engineers Limited have worked in collaboration with Canada Conveyor to design and implement the methods described herein.

Jan 1, 1993

By D. L. Jones, S. Knoerr, J. Mansanti

The Buckhorn Mine in Nevada currently treats oxide ore using heap leach methods, but exploration has identified sulphide reserves which are refractory in nature. Preliminary testwork was conducted on the sulphide material to screen potential pre-cyanidation treatment methods. Processes evaluated included pressure oxidation, biological oxidation, nitric acid oxidation and roasting. An initial economic and process analysis of the results concluded that roasting was the only viable process, and only if the roaster off-gases were converted to soleable sulphuric acid. Further economic analysis indicated that roasting of the whole ore was more attractive than pre-concentrating by flotation, followed by roasting of the concentrate. These results were generalized to show that for high sulphur ore a roaster/acid plant combination is more attractive that either of the other options, ie. pressure leaching or bioleaching, provided the by-product acid is soleable.

Jan 1, 1990

By Jay Hilary Kelley

A ventilation system is described using dual aircourses: one zone occupied by working personnel, the other at the active working face. The two zones are separated by a partition or Shroud. The occupied zone to the rear of the face zone is ventilated adequately but with considerably less air because little gas, dust, or fumes are present. The face excavating zone is sealed and maintained at slightly more negative pressure preventing dust and gas generating from within to escape. Explosive mixtures within the face zone is rendered non-explosive by the introduction of inert gas therein. Each zone is vented separately to the outside of the mine. Because less total quantity of air is required for human breathing, etc, the total ventilation system can be drastically reduced in tan capacity, development entries, and air shafts, -- a great savings in costs.

Jan 1, 1991

By R. Kingman

At Tahawus, New York, National Lead Company operates the MacIntyre Development, This operation produces 10,600 long tons of ore per day for crushing, 8,000 tons for grinding and processing, of which 2,000 tons per day reports as tailing for disposal in an impounded tailing storage area. With the change in location of mining operations at the mine of National Lead Company, a change in the area for tailing disposal by gravity became necessary, This called for the diversion of tailing from near the proposed mining area to areas more favorable for long term storage by gravity. In order to avail the operation of maximum storage for the future, a uniform minimum grade launder was proposed with a minimum velocity and maximum outfall at the discharge. Disposal of the gravity and flotation tailing was formerly accomplished in open ditch from the concentrator at a grade of 1.5 percent. It was desirable to design the new launder at grades less than this for the greater storage elevation.

Jan 1, 1966

By D. Malhotra

This paper discusses the need for periodic auditing of mineral processing flowsheets and the potential benefits a company can gain from a study of this nature. A carefully designed flowsheet audit can have a significant impact on the metallurgical performance in the plant. Several case studies illustrating the potential benefits that can be attained from flowsheet auditing of mineral processing plants are discussed.

Jan 1, 1988

By J. C. Yingling

An approximate analytic- model is developed for minerals liberation when comminution processes are applied to multi-component ores, i.e., ores that include grains of multiple mineral species. The model employs a one-dimensional representation of ore texture similar to that employed by King (1979) and Klimpel and Austin (1983). The spatial texture representation is viewed as being generated by a stationary semi-Markov process. Associated semi-regenerative processes are defined that can be used to establish, approximately, the joint distribution of particle size and composition, where composition refers to the identities and relative proportions of mineral species included within the particle. Numerical predictions made by the model are compared to size and composition distributions observed in previous experimental studies.

Jan 1, 1992

By Samuel M. Brock

Problems related to strip and auger coal mining have grown with the development of the industry and the economy. New technology has produced equipment that has made mining by surface methods not only highly productive, but potentially highly destructive of water resources and natural environments. On the other hand, growth of the economy has produced an increased demand for clean water, and created new demands for amenity values that natural environments provide. Thus, opposing forces have created conflicts in resource use. And these conflicts have made surface mining highly controversial. Resolving the controversy will require the solving of complex economic and social problems. The essence of the economic problem created by surface mining is that, in the absence of proper regulation, substantial costs resulting from the process are borne by the public rather than the mine operator.

Jan 1, 1968

By B. Denby, R. Hollands

Mine information is often multi-disciplinary, dynamic and spatially complex. Different departments use the same data in many different ways, information changes over time and mines change their shape continuously. Earthworks InTouch is a radical VR-based system developed by AIMS Solutions and marketed by Earthworks, which provides a rapid and intuitive interface to a wide range of mine information. VR is used to provide an interactive and visually accurate, dynamic 3D model of the mine workings and equipment operating in the mine. Individual objects in the mine can be linked to external applications that provide up-to-date and context sensitive information. Equipment movement can be simulated or tied in to real-time survey from GPS systems for example or excavator productivity data can be extracted from a production database. The paper will highlight the major advantages of using such a VR interface to access valuable and time sensitive information.

Jan 1, 2002

By George A. Takach

The U.S. Bureau of Mines is conducting research with the goal of automating underground coal mine roof bolters for greater mine safety. In the project described here, the Bureau has focused on automating the drilling portion of the drilling and bolting cycle. A drill monitoring system designed and developed by Parvus Corp. of Salt Lake City. UT, was placed on a Bureau model roof- bolting drill. The drilling parameters of torque, thrust, rotation rate, penetration rate, and position are monitored through sensors connected to an asynchronous, control-oriented local area network (LAN) that communicates with data-accumulating and data-processing nodes. By placing microprocessors at the two data nodes and at the valve control nodes, and combining these nodes with a personal computer (PC), the monitoring and control system can achieve parallel processing capabilities. Such capabilities are referred to as locally intelligent distributed processing. Only data that have changed significantly are reported through the LAN to a supervisory control and data acquisition (SCADA) system mounted on an IBM- compatible 80286 PC. The SCADA system displays the values of the drilling parameters and calculates the specific energy of drilling, which is then used as an indicator of the type of rock being drilled. Besides monitoring the drilling process, an operator at the computer can control the rotation and thrust of the drill from a remote location through the SCADA program and can set drilling parameters on the basis of observed values of the specific energy of drilling.

Jan 1, 1992