Search Documents

By Brenda J. Wolfe

Following successful laboratory and pilot plant investigation of dewatering characteristics of molybdenum concentrate produced by a Chilean copper/moly producer, two (2) DENVER SALA 500 Series Tube Press Filters were installed in 1994 to handle the total production volume. Moisture requirements in the filter cake have been consistently met, eliminating the need for thermal drying after filtration. Operating data and Tube Press Filter are described herein.

Jan 1, 1995

By D. Carlson

At the Freeport Indonesia Grasberg Mine in Irian Jaya, Indonesia, a system of underground drainholes and surface drain wells have been designed and are currently under construction. The underground drainholes are located at elevations of approximately 9,600 feet and the surface drainwells located at elevations ranging between 12,500 and 13,000 feet. Together they will be used to drain the ground water contained within relatively incompetent rock. This drain system will allow for the successful dry mining of the open pit, and provide slope stability of the pit wall. The surface drain well network, when completed will allow for the draining of ground water to the Amole Drift where the underground drainholes are constructed.

Jan 1, 1998

By G. R. Giuliani

Hanna Mining Company's Groveland Mine is located in the Upper Peninsula of Michigan. The low grade iron ore deposit consists of a mixture of magnetite and hematite with chert, jasper, quartz and various iron silicates (1). The ore is beneficiated by magnetic separation and anionic flotation of the iron minerals with chemical depression of the silica. The magnetic concentrate makes up about 75% of the concentrate. The concentrate is pelletized at the rate of 2.0 million LTPY of pellet production. The concentrator facilities were started up in 1959 and the concentrate was marketed as sinter feed until 1963 when the concentrator was expanded and the pelletizing plant was added. The pellet plant now consists of regrinding, elutriation, filtering, balling and induration. The pellet machine is a straight grate which employs updraft drying and cooling and downdraft drying, preheat and firing. It is necessary to regrind the concentrate before pelletizing. The con-centrate is 60% passing 325 mesh, with a surface area of ±lOOO cm2/Gm, and must be ground to about 83% passing 325 mesh, 1600 cm2/Gm blaine surface area, for pelletizing. The energy for regrind has been reduced from 12.5 KW per LT to 8.80 KW ate of 2.0 million per LT. This was the result of changes made in the concentrator where originally a coarse spiral concentrate, instead of the magnetic concentrate which is screened on fine screens to reduce the coarse fraction and prevent overgrinding before flotation, was produced. Also in 1968 an additional concentrating line was added to the concentrator which employs more grinding power than the other three lines. The demand for a high iron grade and lower silica pellet resulted in the investigation of different schemes of upgrading the reground concentrate which had more iron values liberated during grinding for surface area. The reagentized material presented many problems, mainly in selectivity trying to flot the iron and with high reagent consumption having to dereagentize the concentrate for amine silica flotation, in the various flotation systems tried. Tests were then conducted with elutriation (2) which proved satisfactory by removing the lower specific gravity, fine gangue material from the heavier material with the

Jan 1, 1977

By B. Campbell

This paper will detail the successful construction methods of a 20- foot diameter wet well shaft, approximately 180 feet deep in overall depth and 150-feet below the water table, adjacent to Lake Nacimiento, in San Luis Obispo County, California. In addition to this, highlights will include the selection process in determining the most economical support of excavation, while minimizing risk of large water inflows as indicated in the Owner?s Geotechnical Baseline Report (GBR).

Jan 1, 2010

By A. Singh, C. Da Corte

"South Africa possess the biggest fluorspar reserves in the world followed closely by China. In light of the current commodity downturn this paper explores the use of Dense Media Separation (DMS) as a coarse pre-concentration method for two fluorspar deposits located in South Africa in which the dominant gangue is carbonate present in the form of dolomite and calcite. Heavy Liquid Separation indicated that conventional pre-concentration of the drill core samples from both deposits would result in unacceptably high fluorite CaF2 losses. At a maximum CaF2 loss to floats of 5% the benefit of DMS would be economically marginal and difficult to justify as a conventional pre-concentrator. In light of cashflow constraints, a twin flowsheet was proposed for the sole purposes of upfront cash generation in which the majority (67-77%) of the CaF2 would report to a high grade flotation plant in 38-41% of the mass whilst the rejects would be stockpiled for flotation at a later stage. Considering the proposed twin flowsheet approach the high grade product split was achieved using DMS and this paper documents the challenges encountered and results achieved. INTRODUCTION Fluorspar is the commercial term for the mineral fluorite (calcium fluoride, CaF2). Worldwide production of fluorspar is dominated by four countries namely China, Mexico, Mongolia and South Africa. Although South Africa is the fourth largest producer, it has the largest fluorspar reserves closely followed by China (U.S. Geological Survey, 2017a). Fluorspar is broadly categorized into two grades namely acid grade also referred to as acidspar (>97% CaF2); and sub-acid grade (ceramic and metallurgical grade) commonly referred to as metspar (=97% CaF2). Acid grade fluorspar is used for the production of hydrofluoric acid (HF) which in turn is used for the manufacture of fluorocarbons and semi-conductors in the electronics industry; metal processing; the production of insecticides, herbicides and cleaning detergents, and the manufacture of uranium tetrafluoride used to concentrate the uranium isotope 235 for use as a nuclear fuel (British Geological Survey 2010; Miller 2001). Ceramic grade fluorspar (85-95% CaF2) is used in the ceramic industry as a flux and opacifier in the production of glass and enamels. Ceramic grade fluorspar is also used to make coatings for welding rods and as a flux in the steel industry. Metallurgical grade fluorspar (60-85% CaF2) is primarily used in the steel industry as flux to reduce the melting temperature and remove impurities in steel making. Similarly metallurgical grade fluorspar is also used as flux in cement production to reduce energy consumption (British Geological Survey 2010; Miller 2001)."

Jan 1, 2018

By C. Pritchard

John Marks said in his acceptance of the Hartman Award in 2008, “I guess that without the occasional complaint, your mine is probably over-ventilated” (Marks, 2008). Miners are seldom in this situation and spend much of the time trying to find enough air to keep an operation running. With examination, there are usually changes that can be made to increase the efficiency of ventilation systems. Mine ventilation air is a costly commodity, especially by the time it has been heated or cooled and moved to the bottom of the shaft and through the mine airways. Modifications that result in surplus mine ventilation air could bring financial and environmental benefits. Some issues mine operators have needed to address recently are increased airflow requirements to dilute diesel particulates in metal and nonmetal mines, to ventilate reserves that are deeper, hotter, and further away from fans and shafts, and to meet demands from increased production. This paper discusses successful methods to find additional usable air when there is no extra ventilation capacity. Most of the options presented in this paper are useful for metal/ nonmetal operations but some may be applicable to coal as well.

Jan 1, 2009

By D. V. Bush

The economic application of real time computer control can be broken down into 2 broad areas of concern. The first would be in gaining the most efficient utilization of energy. The second would be in improved product quality. This paper will be primarly concerned with the first area of efficient energy utilization as that area has the greatest effect on costs and thus net profits. Most process control strategy attempt to achieve the greatest comminution with the least amount of energy thus maximizing efficiency. A more direct approach to energy control involves a total mine and mill energy management system. In most cases these systems have an ability to achieve a very short payback period with the greatest return on investment.

Jan 1, 1986

By James A. Martin

In relating geology and mineral resources to the nongeologist engaged in planning and zoning, a major hurdle to overcome is often the concept of natural resources. Statements listing such "resources" generally include and often may he limited to such items as "open space", "buildings of historical value", "forest and wilderness areas", and "sites of natural beauty" but seldom mention minerals even where they are of significant economic importance to the area. Unfortunately, mention of mineral resources is often limited to statements calling for tight controls on mining to prevent "ravaging of the land". While, the concept of sequential use involving mining is sometimes acknowledged, it is frequently done in such a manner that this approach is discouraged. In the conflict for land between urban development, recreational open space and mineral extraction, far too often the mineral industry will be the loser. In Missouri, there have long been continuing requests for geologic and resource data for planning purposes from city and county government and from Federal agencies for inclusion in the various river basin studies and Soil Conservation Service projects. These reports vary in detail from concise statements of the geology of an area to rather lengthy reports on mineral and water resources, bed rock and engineering geology characteristics. In most cases, these reports as written were directed to a geologically-oriented reader. Our initial approach to presenting geologic data to the land-use planner was in the area of engineering geology with attempts to show the limitations that bedrock and soil conditions can place on development. The first formal reports, engineering geology studies of urban areas, were released by the Missouri Geological Survey in

Jan 1, 1976

By Donald D. Gullickson

The entire system is built around pre-designed and pre-engineered modules which are assembled to meet the metallurgical and production parameters of the project. The carbon vessels are the key to the flexibility of the system. The vessels are made of a coated mild steel, which allows the carbon vessels to be used in the adsorption, desorption and acid wash cycles. In the adsorption mode, the solution is pumped up-flow through four (4) vessels in series at 250 gpm fluidizing the carbon bed. When the carbon in the lead vessel is loaded, it is disconnected from the adsorption circuit via rubber hoses with quick-disconnect fittings. The second vessel is then made the lead vessel and a stripped carbon vessel is added to the end of the adsorption circuit.

Jan 1, 1998

By Vladimir Jindrich

This paper presents a history of a successful three year effort in locating a large, economic deposit of high purity limestone. The exploration program has been carried out by Ernest K. Lehmann & Associates, Inc., geological consultants, for Dravo Corporation, owner of the limestone property which is now under development. The permission of Mr. L. P. Struble, Jr, President of Dravo Lime Company, and Mr. M. W. Robinson, Director of Research and Development, to present this paper is gratefully acknowledged. The limestone property is on the Ohio River near Maysville in northern Kentucky, 60 miles east of Cincinnati (Fig. 1). The area lies at the eastern flank of the Cincinnati Arch, a regional structure where the Lower Paleozoic strata crop out below the adjacent younger sedimentary rocks of the Illinois and Apallachian basins. In general, the limestone formations of the Middle Ordovician High Bridge group offer the best potential for industrial limestone in Kentucky and adjacent parts of Ohio and Indiana. These formations are exposed along the axis of the Cincinnati Arch in central Kentucky. Toward the west, east and north, strata of the High Bridge group are progressively deeper, concealed beneath a succession of interbedded fossiliferous limestone and shale. The High Bridge group limestone formations are shallow-marine deposits largely of tidal flat, shallow lagoon and related environments. Principal lithologies include cryptocrystalline micritic limestone and crystalline dolomitic limestone to dolomite. Shale and bioclastic limestone are subordinate but the proportion of shale increases in the basal formations. Characteristic, is the occurrence of several thin beds of bentonite that serve as regional stratigraphic key horizons.

Jan 1, 1975

By T. Klemetti, W. H. Su, M. A. Van Dyke

Entry stability in coal mines is dependent on geologic conditions and engineering controls. Most engineering controls in ground control are predictable and standardized for typical geologic conditions. However, geologic anomalies may exist that are difficult to detect with traditional core hole drilling. Borescopes offer a cost-efficient way to gather more geologic data between core holes. Additional data obtained from borescope results provide a clearer picture to enhance detection of hazardous conditions due to geologic anomalies. The equipment, methods, and analysis of borescope results provide geomechanical engineers with a clear understanding of strata behavior and the best information to implement roof control plans and supplemental support to enhance miner safety and health. INTRODUCTION Borescope technology has changed very little since its inception. However, the idea to use borescopes to examine roof strata started with the U.S. Bureau of Mines in 1979 with the production of a fiber-optic borescope (FitzSimmons, et al., 1979). The first documented use of a borescope in the coal mining industry began during the 1980s in Australia by researcher John Shepherd. Shepherd’s idea was to use a borescope to collect a series of data points from the roof lithology and compose a geologic cross section. The cross section was then used to identify key features that suggested the beginnings of roof failure. The features Shepherd identified were bedding plane separations in the roof and low angle, extension, and tensile failures. Shepherd also suggested that the borescope findings could be used for geologic mapping for lithological variation, fracture distribution, and determining if supplemental roof support was needed (Shepherd, et al., 1986). In the United States the first publication about borescope usage for coal mine stability assessment was by Su and associates in 1999, who specifically related the combination of using borescope, geophysical, and corehole data to produce geologic hazard maps (Su et al., 1999). This work directly linked the usage of a borescope with the design of supplemental roof support. The use of borescopes in mining was adopted industry wide by the 2000s. Operator case studies were being published using borescopes to aid in supplemental support recommendations and hazard mapping. An Australian study published in 2007 based the optimization of secondary support after each longwall pass on the results of borescope data. The study stated that the borescope was an invaluable tool for understanding roof behavior (Black, et al., 2007). In 2009, a publication by the National Institute for Occupational Safety and Health (NIOSH) took the concept of borescoping one step further. The work centered around creating a roof quality index (RQI) for limestone mines based on borescope data. The RQI attempted to assign a ranking to establish the nature of the roof and its stability (Ellenberger 2009). In theory, this would have been a very useful tool, but the RQI system has not been widely adopted in the industry.

Jan 1, 2019

By Yuting Xue, Xin Li, Ihsan Berk Tulu, Gaobo Zhao, Deniz Tuncay, Mindi Ruan

Most coal mine roofs in the Appalachian region consist of laminated shale, which is prone to brittle failure. Accurate modeling of shale roofs is vital for studying cutter failures of these shale roofs, and ordinary and formational bedding planes play a significant role in the response off the shale roof to mining-induced stresses. This paper presents a robust method for constructing three-dimensional shale roof models using limited borehole cores and leveraging image processing techniques. The approach begins with image extraction from shale cores. Then, we extract the portions that feature the core and employ image-stitching techniques to merge them seamlessly. Once the images are stitched, they are duplicated horizontally and merged to create a cross-sectional plane image representing a shale roof. This roof cross-sectional plane image serves as an input to our proprietary Digital Image Processing (DIP) algorithm, which is adept at extracting ordinary bedding planes (interfaces that represent color transitions between a single shale unit). The extraction process involves transforming discrete core points (ordinary bedding plane pixels) into continuous lines representing ordinary bedding planes. Finally, extending this method into the third dimension, the model is further extrapolated to form a comprehensive three-dimensional shale roof. Through this process, the geometry information of ordinary bedding planes can be extracted for each type of shale in cores, including sandy shale, gray shale, dark shale, etc. This work bridges the gap between limited core data and comprehensive 3D geological modeling, offering valuable insights into identifying and quantifying the variations in different shale roof geologies.

Jun 25, 2024

By D. Newman

"The U.S. stone industry is in a transition from surface quarries to single and multiple level underground stone mines. The factors driving this transition include surface quarries; ? reaching their economic stripping ratio, ? encroaching on the mineral reserve boundary where the remaining reserves are below the active pit, ? dust, noise, and blast vibration concerns as suburban neighborhoods and development move into formerly rural areas. Ground control is critical to the success of a safe and productive, mining operation. The primary focus of the ground control engineer in an underground stone mine is the stability of the roof or back, development and benched pillar stability, stability of the sill pillar between vertically adjacent mining levels, and floor stability. Roof stability begins with the selection of a stable back horizon based upon the presence of a thin shale parting, stylolite, or other discontinuities from which the production shot can easily ""peel"" away leaving a stable back stratum. Room width and the decision of whether to bolt the roof, the bolt length, bolt type, bolt diameter, and spacing of the support is controlled by the thickness, fracture spacing, jointing, and material properties of the back strata. Horizontal stress controls the header and crosscut azimuth as to avoid driving perpendicular to the maximum horizontal stress direction. Stable pillar dimensions depend upon the interaction of the; ? vertical stress resulting from overburden thickness and multiple level interaction of overlying level(s), ? mining height during development and the final mining height after floor shots are taken while benching, ? presence of faults, folds, or joints passing through the pillar, and ? stone lithology recognizing that the presence of oolitic bands, shale partings, and bentonite beds create zones of weakness that can destabilize an otherwise competent pillar. Floor stability is typically not a significant issue for underground stone mines because the bearing capacity of the stone exceeds the vertical pressure transferred through the pillar. However, floor heave can be a ground control issue where shale partings, moisture sensitive strata, weak stone bands, or horizontal stress is present. Roof stability and pillar stability problems can be initiated as the floor heave enables the pillar and roof to settle. The ground control issues for underground stone mines are most clearly presented through a series of case histories. The case histories presented in this paper are a mix of ground failures and successful mining. The focus is on the geotechnical data required for underground stone mine ground control for roof, pillar, and floor design and stability analysis."

Jan 1, 2016

By Stephen Utter

One function of mining is to supply oil shale of the required grade and characteristics to surface retorts. The mining methods must he safe, efficient, and environmentally acceptable. Although the Bureau of Mines no longer conducts research on methods of mining fossil fuels, including oil shale, its many years of activity in that field resulted in a significant body of findings. This article summarizes some of these findings, with respect to oil shale mining. The large areal extent of Green River formation oil shales and the diversity of geologic, hydrologic, topographic, and other conditions, preclude the use of any one single mining and waste management technique. Instead, in most instances, methods and equipment will be chosen to meet site-specific conditions. Such methods include conventional surface mining (open-pit and strip), underground mining (room-and-pillar, sublevel stoping, caving) and in situ extraction (true in situ from surface drill holes and modified in situ from underground retorts containing rubblized oil shale). Combination or hybrid systems may prove suitable. Both surface and underground backfilling of spent shale waste may be practiced. Tremendous amounts of oil shale must be mined, processed, and the waste shale properly disposed of in order to meet projected industry production goals. For example, about 1.4 tons of oil shale averaging 117 L of shale oil per ton are required to produce one bbl of oil. A plant with a daily production of 8 dam' (50 000 bbl) of oil would thus require some 68 kt of raw shale daily. This is more than the average daily production from any underground mining operation.

Jan 1, 1981

By Gunter Fauth

The setting of tasks for the process control of coal cleaning, and in this connection the requirements for instrumentation can be classified into the following three fields: - Monitoring the operation of individual units, or process steps, - Control of units or process steps, - Control of the entire coal cleaning process with the intention of optimizing the operation and the profitability of the process. Instrumentation is affected by the type of cleaning processes. For introduction Figure 1 shows the simplified flow sheet of coal preparation which is usual in the German Ruhr District and in which desirable places for the measurement of ash, moisture and sulfur content are marked. The preparation plant is supplied with run-of-mine coal from the shaft via a homogenization facility. In a first step of primary classifying the raw feed coal is screened at about 10 mm. The raw coarse coal ( = 10 mm) is sorted by jig washers or heavy-medium separators. the raw fine coal (< 10 mm) at first is pneumatically sized at about 0.5 to 0.75 mm. The fines, the aspirated dust, are a finished partial product which will be added to the final metallurgical or steam coal. The material 10 to 0.75 mm subsequently is sorted in fine coal jigs and dewatered in centrifuges. The sludge obtained with the wet cleaning processes is dewatered in thickeners and fed to the flotation. Concentrate and tailings are dewatered by filters or bowl centrifuges and by chamber filter presses or belt filter presses, respectively. The partial products coarse coal, fine coal, flotation concentrate, aspirated dust, and middlings are blended to result in the sellable products metallurgical and steam coal.

Jan 1, 1984

By Hugh Boyd

Jet pulverization is a relatively new tool for fine grinding. It is not yet in general use in the mining and ore dressing fields, since most of the requirements in these areas have been for relatively coarse particle sizes. As the need for finer grinding increases - because of different ores, new products, and new values being sought - jet pulverization will, increasingly, be properly used.

Jan 1, 1969

By R. J. Caine

Like most major firms engaged in project management, Dravo Corporation faces a constant challenge to keep its management systems in tune with the ever-increasing demands imposed by larger and more complex projects. This paper suggests that one of the key elements in meeting this challenge is more effective organization of project data. It reveals some of the details of a program at Dravo&apos;s Minerals 6 Metals Division which seeks, through better organization of project data, to improve Dravo&apos;s capabilities in estimating, cost control, scheduling, performance reporting and material control. In particular, this paper discusses ideas Dravo is developing for improved job numbering, codes of accounts, requisition and purchase order numbering, inventory cataloging, and employee/badge numbering.

Jan 1, 1980

By M. R. Shahan, W. R. Reed

A laboratory apparatus (shield dust simulator) was designed and constructed to simulate the dust generated during the advance of longwall hydraulic roof supports, or shields. The objective of the study was to develop a tool that could be used to test the hypothesis that foam applied to a mine roof prior to a shield advance could be used to reduce the respirable dust generated during shield advances. This paper will outline the design parameters for the development of the system, as well as describe baseline testing of coal and limestone dust. Results show the average instantaneous respirable dust concentrations that occurred during simulated shield advance. Confidence intervals were calculated from the instantaneous respirable dust data to determine the repeatability of the data produced by the device. INTRODUCTION During longwall mining, miners can be exposed to respirable dust that is generated during the advance of hydraulic roof supports or shields. National Institute for Occupational Safety and Health (NIOSH) researchers have conducted numerous surveys of longwall mining operations, benchmarking the operating practices and dust control measures in use. It has been determined that the shields are responsible for 27% of the respirable dust that is generated on the longwall face [1]. The dust generated by the shield advances ranks second, next to the longwall shearer which is accountable for 43% of the respirable dust generated on the longwall face. The respirable dust generated during the advance of the shields can be a significant contributor to the respirable dust exposure of the mining personnel operating at the longwall face, especially since some of this dust is generated in the walkway. Control systems designed to reduce the dust levels generated during the shield advance have the potential to greatly reduce the respirable dust exposures of the personnel downwind of these activities. One control technology to decrease the dust generated by the shield advances would be to apply a layer of foam to the forward shield-roof interface prior to the shield advance [2]. The blanketed layer of foam would interact with the material located on the top of the shield during the advance, preventing a portion of that dust from becoming entrained in the mine air. This layer of foam would be applied using a foaming nozzle located on the longwall shearer body that would spray foam on the roof surface as the shearer passed. Substantial laboratory work has been completed to determine the feasibility of this type of foam application. NIOSH engineers have classified the various characteristics of foaming agents, using foam expansion ratio and drainage as important properties, as well as developed the mechanical systems required to apply the foam safely to the mine roof [2, 3]. The construction of an apparatus that could simulate the mechanical interaction between the dust-laden shield top and mine roof was necessary to adequately test the hypothesis that foam could be an appropriate control. A team of engineers designed and constructed a shield dust simulator system allowing for in-house testing prior to a full-scale field investigation.

Jan 1, 2019

By Frank R. Cappuccitti

This paper will deal with current market trends for sulfide mineral collectors in three distinct parts; the global market for sulfide collectors, collectors as tools to solve mineral processing problems and new collector Research in the 1990&apos;s. The global market and manufacturing of sulfide collectors will be detailed as well as the trend towards using increasing amounts of specialty products. The use of Total Quality Concepts for laboratory and plant evaluations of new products will also be discussed. Research in the 1990&apos;s for sulfide collectors will need to focus not on the development of new chemical species but on the application of the new technologies that have already been developed.

Jan 1, 1994

By J. J. Sammarco

Computer-aided control of a mining machine pl aces its operator in a safe, remote location, thus reducing health and safety risks, Sensing systems that provide machine position (xy coordinate) and heading (yaw), are extremely useful in aiding remote positioning of mining machines. The U. S. Bureau of Mines has developed two sensing systems for position and heading information: A scanning laser system based on the Lasernet sensor and a mechanical position and heading system based on linear-position transducers. The Bureau is also investigating a system from Honeywell, the modular azimuth and positioning system that employs ring-laser gyroscopes. This paper presents a brief background and status of these sensing systems as applied to the remote positioning tasks of a continuous mining machine. Included are field test results of each system operating in a room-and-pillar research section at a cooperating mine in West Virginia.

Jan 1, 1992