Search Documents

By H. Huang, R. N. Gow

"Previously, Gibbs’ phase rule was applied to mass-balanced EH-pH diagrams for the Cu-As-S-H2O system. Diagrams were generated using the stoichiometry of enargite as a basis. In this study, the calculations were expanded to cover the stoichiometries of three other Cu-As-S minerals (tennantite, sinnerite, and lautite) and compared to enargite. Stability regions within the resulting EH-pH diagrams were found to change with stoichiometry such that a particular mineral would predominate if its stoichiometry was used in the calculation. Solution speciation was also found to vary, with thioarsenate being the best example. This stoichiometric effect helps to explain results reported in the literature and would be difficult to realize if it were not for mass-balanced calculations. INTRODUCTION A comprehensive thermodynamic review has recently been conducted on the aqueous copper-arsenic-sulfur system (Gow et al., 2014a-d). The free energies of over 100 species were collected from various authors and thermodynamic databases to produce mass-balanced EH-pH diagrams, using the thermodynamic equilibrium calculation software, STABCAL (Huang, 2014). The full database was listed and discussed by Gow et al. (2014A). Resulting diagrams were generated for enargite and confirmed with Raman spectroscopy using bulk mineral electrodes in order to identify reactions spectroelectrochemically. Theoretical calculations agreed well with the experimental results under alkaline conditions (Gow et al., 2014a), acid conditions (Gow et al., 2014b), and alkaline sulfide leaching conditions (Gow et al., 2014c). In this study, additional mass-balanced EH-pH diagrams are generated by changing the copper-arsenic-sulfur stoichiometry from enargite (Cu3AsS4) to tennantite (Cu12As4S13), sinnerite (Cu6As4S9) and lautite (CuAsS). Regions for the thermodynamically stable species are shown to change with the four different mineral compositions. Potential leach conditions, both for co-dissolution and selective dissolution techniques, were examined for differences in predominant species according to changing copper-to-arsenic ratios, sulfur compositions, and sulfur oxidation states."

Jan 1, 2015

By Benjamin Grunauer, Anthony Iannacchione, Taylor DaCanal

"In Pennsylvania’s rich mining history, various forms of room-and-pillar mining have been in use for over 150 years. Longwall mining, introduced in the late 1960s, occupies only the last 60 of those 150 years and now represents the dominant method of extracting coal in the Pittsburgh coalbed. The introduction of longwall mining allowed larger quantities of coal to be extracted in safer and more efficient manners than room-and-pillar mining. However, the associated formation of subsidence basins have elevated both the number and intensity of watersource and surface structure impacts. When these first longwall panels were mined the factors responsible for these impacts were poorly understood and regulations were focused only on surface structures. Today, with over 600 panels mined under a wide range of conditions, these factors are known and regulations have developed to help mitigate water supply and surface structure impacts.The cause and severity of surface effects are thought to be dependent on multiple factors, including the location within the subsidence basin, overburden, panel width, and orientation of the panel. The changing characteristics of over 600 longwall panels mined in the last 60 years are analyzed to determine factors important in subsidence related surface impacts. This study compares the location of the surface impacts with the longwall panel size, overburden, and maximum predicted vertical subsidence. The data shows that changing these characteristics are impacting surface features in a significant manner as measured by the number of company liable reported effects.INTRODUCTIONLongwall mining has occurred in Pennsylvania for over 60 years, and at the current mining rates, longwall mining is expected to continue in the Pennsylvania Pittsburgh Coalbed until the reserves are exhausted. Figure 1 shows all mining that has occurred in the Pittsburgh Coalbed, as well as the area that is left to mine. It is predicted that there are 40 years left of longwall mining on the Pittsburgh Coalbed, under the assumption that 50% of the total 280,000 acres will be mined at the current rate of 3500 acres/year."

Jan 1, 2019

By Jerry M. Whiting

Greater awareness of the increasing need to develop supplementary energy sources is accelerating us towards many basic decisions regarding future utilization of mined energy materials -- uranium, coal, oil sands and oil shale. The latter material comprises a major potential source of oil which will require creation of unusually large and low-cost underground mining systems. In this paper, the author briefly outlines and analyzes several of the factors which continue to provide the somewhat unique character of oil shale nine planning and mine operation.

Jan 1, 1974

By Stanley R. Riggs

The rocks exposed in the phosphate district are of Neogene age and consist of clayey quartz and phosphorite sands overlying phosphatic dolomite. The Bone Valley Formation is redefined as a marine phosphorite containing primary phosphorite and abundant terrigenous sediments. It contains a Middle Miocene vertebrate and invertebrate fauna and conformably overlies the Hawthorn Formation containing similar invertebrate fauna. A new, unnamed formation, with Pliocene and Pleistocene fauna and containing reworked phosphorite, overlies the Bone Valley disconformably. Its phosphorite is derived from the subjacent Bone Valley by post-Middle Miocene erosion and deposition in stream channels and marginal marine environments. The Bone Valley contains two main types of primary marine phosphorite. Orthocbemical phosphorite, a direct precipitate of microcrystalline phosphorite (microsphorite), occurs as a cement or binder in thin beds. Allochemical phosphorite consists of clastic phosphorite particles that were originally formed as microsphorite on another part of the shelf. Microsphorite was deposited in a very shallow open marine environment which had an abnormally high phosphorous content caused by upwelling currents. The mechanism of deposition is still in doubt, but organisms probably were a major factor. Soon after deposition, microsphorite was indurated, periodically torn up, and the resulting fragments transported and deposited elsewhere on the shelf. These processes account for a great portion of the clastic phosphorite in the Miocene deposits of Florida. The primary fossil skeletal material is of minor importance.

Jan 1, 1965

By H. Nagel, A. P. Schissler

"INTRODUCTION Anadarko Petroleum Corporation (Anadarko) owns a region of oil shale properties acquired as part of the original Union Pacific Land Grant of the 1800’s in southern Wyoming. These holdings are greater than 2 million acres and occur throughout the Green River Formation in southwestern Wyoming. One area was prioritized for further study by Anadarko Minerals called the Kinney Rim in the Washakie Basin due to low environmental impact, proximity to infrastructure, high ore grade, and low mining cost. The area is a low-overburden oil shale resource that can be developed using surface mining methods, processed by conventional surface retort, and placing waste rock disposal back on the bench for a design capacity of 10,000 barrel per day. The purpose of this papers is to present the results of environmental analysis and timeline, the mine plan, and surface ore processing to offer a resource-ready energy source.Mineral rights for the Kinney Rim area are owned by Anadarko, the United States Bureau of Land Management (BLM) and the State of Wyoming. Mining of oil shale for this study targets Anadarko owned mineral resources.GEOLOGY The study area is in the Green River and Washakie Basins in western Wyoming. The host geologic member is the Laney Oil Shale. Figure 2 illustrates the Laney shale within a generalized lithologic cross section.OIL SHALE LEASING The proposed Kinney Rim oil shale mining project is located in an area dominated by a 1 square mile checkerboard landownership pattern with every other section typically administered by Bureau of Land Management (BLM) and Anadarko. Surface and mineral ownership is a split estate legal entity. The immediate Kinney Rim mine plan is all on Anadarko sections."

Jan 1, 2015

By James P. Connell

The Montana Operations of the Anaconda Company constitute an integrated, though geographically separated, non-ferrous metal production complex. The mines are located at Butte and consist of one large open-pit mine, two small underground mines, a precipitation plant for both underground and pit-dump leach water, and the Weed Copper Concentrator. The smelter, located at Anaconda, Montana 25 miles to the west, processes all Butte copper shipments as well as copper materials from both Anaconda and private mines. Copper and zinc are refined at Great Falls, Montana, 165 miles to the north. Other facilities developed over the years include the Anaconda Forest Products Division, the Butte, Anaconda, and Little. Chicago Water Companies, and the Montana Hardware Company. Data processing for these operations has been performed on an IBM 360 Series, Model 30 computer, utilizing a Disc Operating System. This was replaced in September 1970 with a 360 Series, Model 40 128K unit. In addition, some data processing is also done for Anaconda Company operations located at Britannia Beach, British Columbia; Columbia Falls, Montana; Yerington, Nevada; and Twin Buttes and Tuscon, Arizona. The material under discussion in this paper will be concerned primarily with the mining operations at Butte.

Jan 1, 1970

By Georges Cote, Ehsan Alavi, Eren Kusdogan

The City of Toronto's Coxwell Bypass Tunnel is currently being constructed by North Tunnel Constructors (NTC) ULC, a joint venture of Jay Dee Canada, C&M McNally Tunnel Constructors and Michels Canada. This project includes construction of approximately 10.5 km of 6.3 meter finished diameter rock tunnel, five 20 meter diameter storage shafts and eleven tunnel connection drop shafts, along with associated deaeration and adit tunnels. 120 m of Starter tunnel and 70 m of Tail tunnel were excavated with roadheaders to help with the launch of the TBM and as part of the contract base scope work. JayDee Canada in Collaboration with Everest Equipment Co. developed an innovative approach to design and build a stand-alone Ring Machine Erector nicknamed Enterprise to erect precast segmental lining in Starter and Tail tunnels in lieu of Cast-In- Place concrete. This paper describes the design and provides feedback on the innovative procedure used to install the rings.

Jun 23, 2024

By M. P. Meehan

The purpose of this paper is to present the Anamax Instrumentation Department's: responsibilities, organization, preventive maintenance, test facilities, training and applications. The Anamax Mining Company is a general partnership between AMAX Arizona, Inc. (a subsidiary of AMAX INC.) and The Anaconda Company (a subsidiary of Atlantic Richfield). Anamax's product and by-products include: copper, molybdenum, and silver; uranium is to be added as a by-product in early 1980.

Jan 1, 1980

By Mark Gershon

This paper describes a linear programming (LP) application that schedules mining operations in an optimal manner. The model is developed such that it can be applied to a broad spectrum of mining activities. While linear programming has been applied to mine scheduling in the past, the models have been either site-specific or they have only optimized one aspect of mine operations without regard to others. The Mine Scheduling Optimization (MSO) concept makes use of a mathematical model to: (1) Determine the optimal operation of a mine, from mine to plant to market. (2) Account for mine-plant-market interfaces. (3) Optimize operations over the life of the mine. (4) Accomplish long, intermediate, and short range planning.

Jan 1, 1982

By K. N. Han

The dissolution kinetics of cobalt in iodine/ iodide solutions were investigated using a rotating-disc technique. Variables studied included temperature, rotating speed, concentration of lixiviants and the pH of the solution. The overall dissolution reaction appeared to be limited by the mass transfer of tri-iodide through the diffusion boundary layer with an Arrhenius activation energy of <16.2 kJ/mol (4 kcal/mol) over the temperature range of 2 to 42ºC. The pH of the solution had little effect, as long as the pH of the solution was <8. However, when the pH of the solution became >8, the dissolution rate decreased dramatically, due to passivation. The rate of dissolution was in good agreement with the dissolution model developed by the authors earlier.

Jan 1, 1995

By S. D. F. Rocha

The influence of surfactants on the crystallization of calcium sulfate was investigated in both hatch and continuous systems. The investigation was per formed at the following conditions. 343 °K, 28% P205 and with a sulfate level of 2.0%. At concentrations of 5 and 200 µgig, respectively, dodecylbenzene sulfonic acid (DBSH) and sodium diisooctil sulosuccinate (SSNa) promoted both an increase in the size and a reduction in the length/width (L/W) ratio of the calcium sulfate hydrates produced in the hatch and continuous crystallizers. Unique effects were observed in the batch system at higher DBSH concentrations. At 10 µg/g, the precipitation of hemihydrate crystals with a distinct morphology and texture occurred under conditions where dihydrate precipitation was expected. Above 50 µg/g, the precipitation of calcium sulfate hydrates was completely inhibited.

Jan 1, 1996

By J. D. McKay

Continuous column flotation parameter testing, to improve operating methodologies, using coarse bubbles on fluorite ore from Nevada, revealed that retention time is the predominant factor affecting column flotation fluorite recoveries. Column height and feed injection location affected fluorite grades and recoveries because they affected particle retention times in the collection and cleaning zones. Other parameters tested, including froth depth, wash water addition, and axial mixing, showed varying results. Four defined zones within the column were found to have characteristic rates of upgrading per vertical foot. Fluorite-gangue separation was more efficient in a column than in a conventional cell at all particle sizes.

Jan 1, 1987

By W. C. Shanks

The Pioche District of Lincoln County in southeastern Nevada (Figures 1 and 2) has been an historically important producer of silver, zinc, and lead. Economic geology of districts in the Pioche area is summarized most adequately in recent reports by Tschanz and Pampeyan (1) and Gemmill (2) and only a few major aspects will be discussed here. Production in the Pioche District began in 1869 and early mining concentrated on silver-bearing fissures in lower Cambrian quartzites. In the early 1870&apos;s the Pioche District was second only to the Comstock Lode in world silver production (3). More recent mining activities have centered on the other major ore type in the area, bedded replacement of lower Cambrian carbonates by Ag-Zn-Pb sulfide ore. Production of replacement ore peaked around 1950. The present study is focused on the Pan American Mine because it is an excellent example of low grade carbonate replacement deposits, because there is little structural dismemberment, and because access was readily available. Most previous workers have suggested that both the fissure vein deposits and the bedded replacement deposits of the Pioche districts are a result of spatially related Laramide igneous activity. The purpose of this study is to determine whether ore genesis is a result of igneous activity or if mineralization might be related to late diagenetic processes such as formed Mississippi Valley "type" deposits. Stable isotopes of sulfur, carbon, and oxygen in ore and gangue minerals have been studied to determine the probable isotopic composition of the ore fluid and paleomagnetic studies of the carbonate rocks have been utilized to determine timing of mineralization. Additionally, petrographic and field studies of carbonate lithologies were undertaken in an attempt to delineate non-structural controls on ore localization. These studies are still proceeding and the results presented herein are, therefore, preliminary in nature.

Jan 1, 1979

By A. H. Baldo

Covers a very broad spectrum of problems and solutions. The problems are multitudinous and their solutions are sometimes simplistic, sometimes ingenious and sometimes within a very broad interpretation of the law. However, one thing is quite certain: the problems and their solutions will have a direct impact upon corporate and personal well being. First of all, why does one mine in a foreign land? Since the Bronze Age, when ancient man discovered the metallurgy of copper, tin and zinc, intrepid souls have been wandering afield searching for and exploiting those mineral deposits which would create wealth and security for his city-state or community.

Jan 1, 1981

By Hooman Askari-Nasab, AHLAM MAREMI, EUGENE BEN-AWUAH

In oil sands mining, tailings are voluminous unwanted byproducts generated from extracting the desired mineral from the mined ore. Dyke construction and backfilling activities require well-managed techniques to facilitate progressive reclamation at the earliest opportunity. This directly affects the sustainability and profitability of the mining operation. This research introduces a goal programming framework that simultaneously optimizes the (1) production schedule with limited duration stockpiling and directional mining, (2) dyke construction schedule, (3) size, shape and location of tailing cells and (4) mining and processing production targets. The results show that in creating in-pit tailing-cell designs, decreasing the mining-cell volume and increasing the number of mining cells improves the net present value (NPV) of the operation due to increased operational flexibility.

By Gill Montgomery

Although fluorspar is considered an industrial mineral by usage and value, its geological occurrence and the mining and milling methods employed make it more akin to the non-ferrous metal ores. Likewise methods of exploration for it are more like those used in the search for lead and zinc, with which fluorspar is often mixed. In fact, it often takes the mixture of fluorspar, lead, zinc, plus maybe barite to add up to enough recoverable values to make the mineral an ore by definition. This is so true where the fluorspar portion is low grade, perhaps less than 25 percent. Until the development of modern steel milling in World War I times, the invention of aluminum smelting, and development of the fluorine chemical industry and air conditioning, there were few uses for fluorspar aside from ceramic fluxes in the flint glass industry and for uses as glazes for pottery and china. Pure fluorite crystals have long been admired as semi-precious and ornamental minerals of many delicate colors.

Jan 1, 1983

The Bureau of Mines, U.S. Department of Interior, is currently investigating strata interactions associated with the mining of multiple coalbeds. Strata interactions due to subsidence are a result of undermining. This study involves underground investigations at a mine where room and pillar panels are actively being developed through an area of the Sewickley Coalbed which was subsided by undermining of the Pittsburgh Coalbed. Research to date indicates that undermining had little effect on upper mine pillar stability, but had a more severe effect on the development and maintenance of entries. Roof-to-floor measurements recorded over four times more convergence in entries developed over gob as compared with entries developed over support pillars in the lower mine. Consequently, this has led to major roof falls in the active panels, resulting in considerable production delays and supplemental roof support costs.

Jan 1, 1985

By William Gleason

"When Dr. Joseph A. Holmes was named the first director of the U.S. Bureau of Mines in 1910, the challenge in front of the mining industry was urgent and profound. Just three years before the Bureau was formed, the United States’ coal industry saw a spike in fatalities, as 3,242 miners lost their lives, including 918 miners killed in 18 major disasters. Holmes, who is often called the Founding Father of Mine Safety, was charged with researching and finding new and safer methods to conduct mining activities as well as more efficient ways to conduct mine rescue to educate miners.The U.S. Bureau of Mines was dissolved in 1996, but the mission of the Holmes Mine Rescue Association remains intact, although the challenges have changed greatly.During the 102 years between its formation and the 2018 Joseph A. Holmes Safety Association & Holmes Mine Rescue Association Annual Meeting and Training Seminar in Denver, CO June 5-7, the mining industry has evolved to become one the safest industries in the United States, with an injury rate on par with school teachers and better than retail workers. The work of Holmes and the Bureau of Mines plotted a course for others to follow, and the fatality rate has plummeted to historic lows. However, those who work in the mining safety and health sector remain diligent to their cause and are slow to celebrate too much the accomplishments of the past century, focusing instead on the work that lies ahead.“The nature of mining accidents has changed and it is very difficult to make changes when you get down to the asymptotic part of the equation,” David Zatezalo, assistant secretary of the U.S. Mine Safety and Health Administration (MSHA) told Mining Engineering. He was the featured speaker at the Joseph A. Holmes Safety Association annual meeting’s banquet dinner and presented a thorough overview of the mission of MSHA and his goals as its top man.Nominated by President Donald Trump, Zatezalo was sworn in as the ninth assistant secretary for MSHA on Nov. 30, 2017 and brings with him a lifetime of experience in mining. During his presentation, he displayed the chart (Fig. 1) showing the dramatic improvement in safety that the industry has achieved during the past century, but he noted that, as the industry gets closer to its end goal of zero fatalities, it has become increasingly more difficult to cross the finish line."

Jan 8, 2018

By J. E. Murphy

The Bureau of Mines demonstrated ferric chloride leaching of galena concentrate on a continuous bench-scale basis. Leaching was performed at 95° C and with a contact time of 15 min. The ferric chloride leaching solution was continuously fed to a leaching tank at a constant rate for periods up to 45 h. In each test a constant redox potential was maintained in the slurry exiting the leaching tank by controlling the concentrate feed rate. In the 45-h test, lead extraction exceeded 99.5 pct, and the lead chloride produced was 99.97 pct pure.

Jan 1, 1984

By Brendan Demich, Brendan Macdonald, Timothy J. Orr, Jason Navoyski, Jennica L. Bellanca, William J. Helfrich

Recent advances in computing, rendering and display technologies have generated increased accessibility to virtual reality. Virtual reality allows for the creation of dynamic, high-fidelity environments to simulate dangerous situations and test conditions and to visualize concepts. Consequently, numerous products have been developed, but many of these are limited in scope. Therefore, U.S. National Institute for Occupational Safety and Health (NIOSH) researchers developed a virtual-reality framework, called VR Mine, to rapidly create an underground mine for human data collection, simulation, visualization and training. This paper describes the features of VR Mine, including mine generation, simulated networks, proximity detection systems, and the integration and visualization of real-time ventilation models.