Search Documents

By J. Hanna, H. R. Gonzalez

Four Ca-bentonitic clays from Alabama were evaluated for use in diammonium phosphate (DAP) or urea ammonium nitrate (UAN) fertilizer suspensions. The viscosity and gel strength of suspensions prepared with different proportions of a Western bentonite clay and sodium-exchanged Alabama clays were measured as a function of clay content and dispersant concentration. The results obtained suggested that three of the Alabama Ca-bentonites would replace about 40% of the more expensive Western bentonite in UAN and DAP fertilizer suspensions. The performance of the Nu-modified clays, prepared according to the Tennessee Valley Authority soda ash method, was as good or even better than those observed for the Mg-, NaIMg- or K-modified clays. The TVA clay modification procedure appears to be reliable and cost effective.

Jan 1, 1991

By Wilson Blake

A mathematical model based on the finite element method of stress analysis has been used to describe the behavior of the western wall of the Kimbley Pit as its slope was steepened from 45 degrees to 57 degrees. Theoretical stress changes because of slope modification are slight except at the toe of the modified slope. Magnitudes of stress created are small when compared with the strength of a competent rock. Resulting displacement patterns point out the need for determining the in situ state of stress at a site prior to excavation or modification. A comparison of model results with field measurements shows that, in general, the model has described the measured behavior of the west wall of the Kimbley Pit remarkably well.

Jan 1, 1968

By John P. Weir

The planning of an underground mine for successful extraction of a bedded deposit in sedimentary rocks requires the integrated evaluation of many interdependent problems. The development and coordination of feasible solutions are the responsibility of the mining engineer. One of these problems will be discussed herein; this is the design and .layout of mine workings to secure effective control of the strata above and below the deposit. The objective is the simplest possible repetitive system permitting safe maximum recovery at optimum cost. Mining conditions to be encountered must be predictable. The best mining equipment is ineffective unless strata are controlled. Conversely, a mining layout is only of academic interest, if equipment can not be adapted to work it with adequate provision for ventilation, compliance with mining laws, proper ingress and egress and other practical requirements. Strata control, then, is but one of the mining engineer's problems, and the solutions must be worked out concurrently with solutions to other problems. Dr. Karl F. Fetters in his introductory remarks before the Fourth International Conference on Strata Control and Rock Mechanics at Columbia University said that mining engineering ?has come from the stage of empiricism backed by intuitive reasoning, to where it is based on fundamental scientific and engineering principles?. The standard curriculum in mining engineering now reflects such a change. In common with other branches of engineering education, less and less emphasis is placed on practical skills and more and more on broad scientific education. Science, research and the quest for basic truth are stressed, while descriptive courses and the teaching of specific skills are limited.

Jan 1, 1966

Sandvik built its first stone crusher in 1896 and has since grown to become a world leader in mining equipment. ?We are the best in the world, and we can now be even better at making our cone and jaw crushers in different models,? Olle Lundberg, production engineer at the Sandvik Mining factory in Svedala, Sweden told freelance journalist U. Samuelsson, of mekpoint.com. As a specialty manufacturing business under the umbrella of the Sandvik Group, Sandvik Mining is a leading global supplier of equipment, tools, services and technical solutions for the mining industry. Its expertise covers the areas of rock drilling, cutting and crushing, as well as loading, hauling and the handling of materials. Lundberg, along with five colleagues, will write CNC programs for the lathes and machining centers that manufacture Sandvik?s specially constructed casting. In 1999, Sandvik chose ESPRIT computer-aided-manufacturing (CAM) software by DP Technology to program its array of machine tools, and has worked with ESPRIT reseller Holotech, based in Örebro, since 2003.

Jan 1, 2014

By C. D. Litton, I. E. Perera

This report presents the results of experiments to evaluate different types of mine fire sensors in an underground mine environment using a commercially available atmospheric monitoring system. To determine how well carbon monoxide (CO) and smoke sensors respond for purposes of fire detection, experiments were conducted using test fires of different mine combustibles and for both flaming and nonflaming combustion. The experiments were designed to assess the response of fire sensors to different contaminants and different contaminant levels produced from the test fires. The experiments were performed in the Safety Research Coal Mine at the U.S. National Institute for Occupational Safety and Health’s Bruceton Research Facility in the presence of an average ventilating air velocity of 1.6 m/s (315 fpm). Five fire sensor stations were located downstream of the test fire at fixed locations, with each sensor station consisting of four sensors: a CO fire sensor and three different smoke sensors, of which two were evaluated by the Mine Safety and Health Administration (MSHA) for intrinsic safety and the third was used extensively in underground mines overseas but not evaluated by MSHA for intrinsic safety. All four sensors were mounted near the center of the entry and in the upper onethird of the entry height. A UL-listed combination ionization and photoelectric smoke sensor was mounted near the roof at the first sensor station and its responses were compared against the responses of the four CO and smoke fire sensors. Sensor response data, contaminant travel times, and the impact of fire on the existing ventilation flow are discussed as they apply to earlywarning fire detection. Of significance in the analysis is the need for performance standards for mine fire sensors in order to provide for consistent and timely early warning of developing fires.

Jan 1, 2014

By William P. Walsh

In December 1983 the author undertook an investigation in east Texas which was organized to learn the feasibility of applying geophysical techniques over shallow lignite deposits. The work embraced experimental high resolution seismic reflection and offset Wenner resisitivity sounds over three 1/4 to 1/2 mile test sections. This site also was sponsored by Woodward-Clyde Consultants (WCC) and a consortium headed by North American Coal Corporation. The principal objective of this investigation was to learn whether the aforementioned geophysical techniques could be applied over shallow lignite deposits (i.e. located at approximately 100' to 300' in depth) and consequently provide structural and stratigraphic information useful for resource and reserve characterization. A secondary objective was to determine if these same techniques could disclose the nature of the overburden and the distribution of ground water therein.

Jan 1, 1986

By Igor Gonzales G.

Southern Peru Copper Corporation (SPCC) has recently completed the construction of copper leaching, solvent extraction, and electrowinning facilities at their Toquepala and Cuajone plants in Southern Peru. Much of the ore for these new operations is the result of the existing mining operations that have been in existence as early as 1959. At Toquepala, pre-conditioning and bacterial dump leaching of the sulfide ore that was too low in copper content to be processed through the copper concentrator began in 1987. The Cuajone heap leach operation is treating copper oxide ore that has been stockpiled since the Cuajone concentrator began operation in 1976. The pregnant leach solutions from the dump leaching at Toquepala and the permanent pad heap at Cuajone are combined into one plant feed solution. Adjacent to the large dumps at Toquepala, a solvent extraction and electrowinning facility has been constructed. The electrowinning facility has a planned annual production rate of35,000 metric tons per year Grade A cathode copper. Initial production of the cathode copper began in November 1995.

Jan 1, 1996

By Z. Henderson, J. R. Saylor, L. Rojas-Mendoza

"Diesel particulate matter (DPM) is a major occupational health hazard in underground mine environments, even with available abatement technologies. Prior work has demonstrated that micrometer-scale water droplets, or “fog,” may be effective in removing significant number fractions of DPM from a conditioned exhaust stream. Here, a series of laboratory experiments are described which demonstrate that such a treatment can remove significant DPM mass from an unconditioned stream. The removal mechanism involved coagulation of the DPM and drops. The fog treatment removed about 45 percent more DPM mass on average than no treatment. Varying engine load, flow rate and fog droplet number density did not significantly affect the results under the range of conditions tested. IntroductionDiesel engines have seen widespread use for well over a century due to their relatively high thermal efficiency and fuel economy (Heywood, 1988). Recently, however, the adverse health risks of diesel exhaust have become increasingly clear. The term diesel particulate matter (DPM) is used to refer to the solid components of diesel exhaust, which are an ultrafine mixture of elemental and organic carbon (EC and OC) and minor constituents including sulfates and metal ash (Kittelson, 1997). DPM is generally considered to occur almost entirely in the submicrometer range. It is classified as a carcinogen (Occupational Safety and Health Administration, 2013), and epidemiological studies have demonstrated a positive correlation between long-term exposure to DPM and other combustionrelated fine particulates and increased cardiovascular and pulmonary diseases (Pope et al., 2002; McDonald et al., 2011). Many of the risks of diesel exhaust are associated with the physical and chemical properties of exhaust components (Heywood, 1988; El-Shobokshy, 1994; Kittelson, 1997). Exposures are generally measured and regulated on the basis of mass concentration. However, DPM number density and particle size are increasingly recognized as critical factors in terms of health outcomes (Bugarski et al., 2012; Kittelson, 1997; Occupational Safety and Health Administration, 2013; Pope et al., 2002)."

Jan 11, 2017

By K. Perry, R. Eades

"Highwall miners continue to be implemented by operations to increase recovery, improve margins, and justify higher stripping ratios as high quality surface reserves become increasingly rare. Many times, operations facilitate projected underground operations by leaving an intact highwall for development purposes. These facts result in larger highwalls that are left standing for increased periods of time prior to reclamation. As a consequence, worker exposure and risk is also elevated, resulting in higher potential for accidents or fatalities relating to surface highwalls. Highwall stability is a complex issue, dependent on both geologic and mining factors. Dynamic numerical modeling offers the capability to assess possible stability issues related to blasting-induced ground vibrations. Research has been conducted to evaluate the effect of highwall stability due to ground vibrations from blasting events. Additionally, the relationship of amplitude and frequency, and their impact on highwall stability is investigated. The results of this modeling indicate that amplitude has little impact on stability. However, frequency has a significant impact on highwall stability. INTRODUCTION The number of mining fatalities has declined since 2010, and 2016 is currently on pace to continue this trend (MSHA 2016). This decline can be directly correlated to the decline in surface mining activity and the overall decline of the coal industry. However, since 2002 the percentage of surface coal mine fatalities associated with highwall activities remains relatively high, constituting approximately 15% of all surface mine fatalities. 2014 was the first year with a highwall failure fatality since 2011. Most recent surface coal mining fatalities are associated with machinery and haulage. Table 1 provides a summary of the total surface coal mining fatalities, and the number of highwall failure fatalities dating back to 2010.Highwall stability is a complex issue, dependent upon geology and geologic discontinuities within the rock mass, along with highwall geometry, standing time, and applied stresses. Another possible concern that has not been previously investigated is the effect of blasting-induced stresses on highwall stability and the stability of web/barrier pillar systems as a result of ground vibrations from blasting events. Many modern surface coal mines employ numerous extraction fronts that rely on blasting for primary rock breakage. This results in highwall and highwall pillar systems experiencing blasting-induced stresses of many different types and magnitudes."

Jan 1, 2017

By John F. M. Sims

Political issues and a glaring infrastructure deficiency have retarded the emergence of a strong mining component to the Alaskan economy in recent years. Barriers to orderly mineral development are slowly being removed attendant upon changing political circumstances. Infrastructure development, as an investment avenue as well as a responsibility of the State, is receiving much greater attention than in the past. Alaska of course has a rich and varied mining history going back to the 19th Century. This paper, however, focuses on the mining potential, not the mining heritage of the 49th State. The mining industry is emerging from a nadir in the economic cycle - times during which it was buffeted by unsympathetic administrations and confused and confounded by the protracted land status- conflicts prior to enactment; of the Alaska National Interest Lands Conservation Act (ANILCA) and other milestone legislation. Today Alaska's mining industry looks toward a bright and healthy future and, in the process, will become a very important and vital component of the State and national economy.

Jan 1, 1982

By B. Yarar

Samples of coal from an adit in the Fording River District of British Columbia showed hydrophilic properties between depths of 0-24.5 meters and was naturally hydrphobic at higher depths. Laboratory experiments indicated that weathered samples (i.e., those mined at 0-24.5m) could be upgraded by froth flotation at pH<2 following slimes removal. The i.e.p. of samples varied regularly between pH=1.6-4.1, the weathered fractions being at the lower end of the pH scale. These values followed a pattern comparable with the flotation behavior of samples. A patchwise structure for coal surfaces determining the resultant disjoining pressure, which in turn determines flotation-non flotation relationships is postulated.

Jan 1, 1982

By F. B. Brost

In 1976, a decision was made by Anamax Mining Company to install an unusual conveying system to transport ore 10.3 km (6.4 mi) from the new Eisenhower Mine to the Twin Buttes concentrator. The system, supplied by Cable Belt Limited of the United Kingdom, represents a radical departure from conventional belt conveyors. The driving tension is applied through two endless wire ropes driven by a single 2 240 kw (3 000 HP) drive while the belt acts only as the ore carrying medium. Full production was begun in January, 1979. Start-up problems hampered production for several months but were resolved by a joint Anamax-Cable Belt effort. The system has been operating at design capacity for 4-1/2 years, and has proven itself as a reliable, low cost ore transportation system.

Jan 1, 1984

By K. N. Han, X. Xie

The dissolution behavior of palladium powder in thiourea solutions was investigated. The variables studied were temperature, stirring speed and the concentrations of thiourea, acid and ferric ion. Palladium was found to be soluble in thiourea solutions in the presence of an oxidant such as ferric ion. The dissolution of palladium in thiourea solutions was believed to be chemical-reaction controlled, with an apparent activation energy of about 25.3 kJ/mol.

Jan 1, 1997

By K. K. Bhattacharyya

In the Gulf Coast area lignite deposits occur in Texas, Louisiana, Arkansas, Mississippi and Alabama. Lignite has been mined in Texas since the early 1800&apos;s reaching a production of over 900,000 metric tons (1 million short tons) in 1910. With the availability of inexpensive oil and gas, production fall to as low as 16,000 metric tons (18,000 short tons) by 1950 (Henry, 1976). With the advent of the oil and gas shortage in early 1970, lignite production began to increase again. The purpose of this paper is to discuss the geotechnical considerations of mining lignite in the Gulf Coast area, particularly Texas and Louisiana. Lignite deposition occurs in unconsolidated sand, silt and clay environments. Extensive sand units saturated with water may be present within the potential mining depths. This paper describes the geotechnical considerations for designing a surface mine in this geographical area. These factors include geology, hydrology, mining method, and equipment utilization.

Jan 1, 1982

By Adrian Fleming

Adrian Fleming is Executive Vice President of Exploration for Golden Star Resources Ltd., Denver. Adrian is an Australian who graduated in 1973 with an honors degree in geology from Newcastle University, New South Wales. His extensive international experience has spanned exploration, project development, and operations for both large and small companies in Australasia, Southeast Asia, North and South America, and Africa. Adrian has been with the Golden Star group of companies for four years and he is responsible for all exploration activity. ABSTRACT Golden Star acquired the rights to the Omai prospect in 1985 at a time when the country of Guyana was out of favor with the exploration fraternity. Subsequently in the late 1980s and early 1990s, Golden Star acquired exploration properties in Suriname and French Guiana well ahead of its competitors. Golden Star&apos;s strategy entailed identifying windows of opportunity and aggressively pursuing them. We also recognized that the Guiana Shield hosted a significant area of highly prospective greenstones which were comparable in metallogenic potential to similar terrains in eastern Canada, western Australia and west Africa. The geological skills Golden Star developed and the exploration techniques employed to explore deeply weathered rocks are described. The paper highlights the key elements of Golden Star&apos;s strategy and illustrates how some of the milestones reached by the company led Golden Star to establish an enviable portfolio of gold and diamond properties in the Guiana Shield.

Jan 1, 1998

By R. K. Mehta

Stirred ball mill feed used for ultra-fine grinding application requires fine size separation step in order to avoid over-grinding. This paper presents the selectivity curves obtained for oil shale and complex sulfide are using 460 mesh (30 micron) Derrick vibrating screen. Interestingly, the selectivity curves generated from the experimental data were monotonic increasing selectivity for oil shale but not monotonic increasing for sulfide ore. These non-monotonic increasing selectivity curves were similar to the mechanical air separator fishhook selectivity curves described by Luckie and Austin. A 2 stage classification in series model describing the fishhook selectivity curve has been used in proposing the classification mechanism for fine vibrating screens when heterogeneous multicomponent sulfide are undergoes size separation.

Jan 1, 1992

By S. B. Bhagwat

The United States has abundant coal resources that could last at least another century. and probably longer at present consumption rates. Geographically, the coal resources are distributed over the entire nation including Alaska, although there are no coal deposits in the highly populated areas on the two coasts. This allows free access to the coal, but makes transportation more expensive. Not all coals can be utilized equally because they differ vastly in quality. The sulfur content of coals, considered as the most detrimental acid rain-causing element, varies from as low as 0.3 percent in some areas of the western U.S. to 5 percent or more in parts of the Midwest. The chlorine content, which causes corrosion of plant hardware, also varies regionally. The 1990 amendments of the Clean Air Act of 1963 (CAA) require that emissions of sulfur be restricted and rolled back in two stages by the year 2000. There have been a number of reports expressing concern about the future of the industry in the states where high sulfur coal is produced. The remedies devised by the federal government and many coal-producing states in the past to "se-cure" the future of the regional coal industries have focused on the physical task of removing sulfur rather than the economic challenge of doing so at a cost that will enable high-sulfur coals to survive and compete. The past remedies, generally, were not specific enough to account for the characteristics of regional coal deposits and did not look at the coal market as an integrated national and international entity. The State of Illinois has, in recent years, taken a more comprehensive approach to the solution of the problem.

Jan 1, 1992

By Z. Yunquan

The flocculation and dispersion behaviors of microsize wolframite and quartz are systematically studied in this paper. For synthetic mixtures, the floc separatory method on gravity units--electromagnetic vibration table (EVT) and lifting column (LC), have been approached. Satisfactory results can be obtained with a weak shearing. A better metallurgical performance can also be achieved for natural ore slimes through the combined technique. The efficiency is better than that of single gravity separation. Finally, the mechanism has been investigated.

Jan 1, 1990

By D. H. Lynch

This paper is a general description of current Central Florida phosphate mining, beneficiation and product transportation. It is directed and believed to be of interest to engineers not familiar with this industry.

Jan 1, 1978

By Hoke M. Garrett

The domestic cement industry demands about 550 trillion Btu annually, at a time when reduced fuel use has become a necessity due to the energy shortage. In terms of the overall power picture, that 550 trillion Btu, which includes both fossil and electrical energy, means about 0. 870 of all energy consumed in the U. S. The various factors influencing reduction of this energy consumption are the subject of this paper. Nationally, the energy shortage is being tackled on two fronts--increasing supply and reducing demand. Making cement consumes energy; therefore, the industry cannot join the effort to increase the energy supply except indirectly as noted later. Demand can also be attacked on two fronts--by reducing cement consumption or by reducing the amount of energy required to make cement. The following discussions on reducing cement industry energy consumption center briefly on the prospect of reducing cement consumption followed by a broad evaluation of the potentials for improving cement-making thermal efficiency.

Jan 1, 1974