Search Documents

By Arnold E. Lamm

The degree of economic, progress of a nation is measured by its possession and use of energy, sources. The future of coal in the West hinges on its ability to participate and grow in the energy market. A source of energy is, in the long run, only as good as the ability of the industry to develop its reserves economically. The economic development of the tremendous coal reserves, literally hundreds of billions of tons of coal in the States of Colorado, Utah, Wyoming, Montana, New Mexico, and Arizona, poses a very real question in the light of the known mining technology of our day. Basically in America today, coal is mined from the earth either by the strip mine or underground mine method; in the West, the large long-term, contracts now in force with utilities are mostly from coal mines utilizing the strip mine method. However, the preponderance of the known coal reserves of the West are located deep underground and will have to be mined by the various; underground mining processes. The problems encountered in the West with regard to underground mining vary from state to state but, on the whole, do not present what might be considered a miner's bonanza. I do not mean to' infer that the underground coal of the West is unmineable, but I do want to emphasize that the tremendous reserve figures do not present a true picture in the light of present day technology.

Jan 1, 1965

By I. Duckworth

P.T. Freeport Indonesia operates a mining complex located in the highlands of Papua, Indonesia. This district consists of both underground and surface operations. The East Ertsberg Skarn System (EESS) is one of the major orebodies in this district. Subsurface caving of the EESS has been carried out in a systematic series of mining lifts dating back almost 30 years. Present production is from the third lift (Deep Ore Zone), which is scheduled to peak at 80,000 mtpd during 2009, with this rate sustained through 2015. The orebody is proven below the existing caving level, with the next vertical block called the Deep Mill Level Zone (DMLZ). This paper presents an overview of the DMLZ Mine based on recent feasibility level study. The mine is being designed for a peak production rate of 29.2 million mtpy, with 1,803 total ore draw points spread over a panel caving footprint of about 1.3km by 375m. The present reserves for this mine total 501 million tonnes. Located 1,400-1,800m below the original surface, the DMLZ will be one of the deepest caving operations in the world. Production is scheduled to commence in 2015. Discussion is provided on most design aspects including; caving methodology and layouts, geotechnical predictions and risks, ore handling systems, ventilation design and associated infrastructure, high-lift pumping system, cost estimation and expenditure scheduling.

Jan 1, 2010

By L. Yan, C. Zhou, M. Reyes

"The MINER Act requires the installation of post-accident, two-way communications and electronic tracking systems for all coal mines. One communication system which can satisfy this requirement is an electrode-based, through-the-earth (TTE) communication system, which sends signal directly through the overburden of a mine. The performance of these types of systems relies on several controlling factors such as earth conductivity, overburden depth, operating frequency, TX/RX antenna length, TX/RX offset, TX/RX orientation angle and TX current. In an effort to estimate attenuation through the earth, NIOSH researchers developed an analytic solution for the electrical field distribution of an electrode-based TTE communication system for the extremely low-frequency (ELF) range (< 30 Hz) or DC excitation source. The analytic model was then validated using test data measured at an operating coal mine. The validated model can be used to optimize the operating frequency, estimate the required transmitting current, choose appropriate TX/RX orientation, and predict the performance of an electrode-based TTE system at a coal mine. INTRODUCTION One of the requirements of the Mine Improvement and New Emergency Response Act (MINER Act) of 2006 is the installation of post-accident, two-way communications and electronic tracking systems for all underground coal mines. As one of the through-the-earth (TTE) wireless communication methods available for the mining industry, the electrode-based, or linear, TTE systems establish communication by inducing a current within the earth medium by use of a pair of current probes. The resultant current is detected as a voltage by a similar set of distant probes. These probes could be an insulated piece of wire tied to two electrodes grounded at distant ends, or the grounded ends could be rails, roof bolts, or grounded electric rods. The analytical solution developed in a homogenous half-space, for this form for various transmitter/receiver (TX/RX) configurations, will be presented in this paper. The communication signals can be sent either from underground to surface (uplink) or from surface to underground (downlink). In order to achieve a successful communication link, it is necessary to understand the electric fields within the earth so that the appropriate size of transmitting antenna, TX/RX relative orientation, and operating frequency can be chosen. Hill and Wait gave the explicit forms of partial magnetic fields and partial electric fields of electrode-based TTE downlink communication with finite cable length [1]. In prior research, the E-fields of electric line transmitter were obtained for a static TX current [2] [3]. In this paper, the general and explicit forms for electrode-based TTE electric fields are developed and presented. The solutions for the extremely low-frequency (ELF) range (< 30 Hz) or DC excitation source obtained from these forms are presented. Also, factors that affect the E-field strength at RX are discussed."

Jan 1, 2017

By Deepak Malhotra

INTORDUCTION Mining operations are unique In that they handle large volumes of water (millions of gallons) daily. The water contains dissolved metals, processing chemicals, organics, and other contaminants, There are several sources of water contamination at mine sites: mines, mills, tailings ponds, and Industrial/utility complexes. Utility waste water generally represents a very small portion of the total process water utilized in a normal milling operation and hence will not be addressed in this paper. Mine drainage can represent a significant amount, thus having an Impact on the recovery of metals, especially In Industrial minerals operations, and may have to be treated separately. The National Pollutant Discharge Elimination System (NPDES) effluent limits are becoming more stringent, thereby requiring mining operations to treat process water prior to discharge to the environment. The general trend Is to move toward a closed-loop waste system and treat only that small fraction of process water which Is to be discharged to public lands. The following section discusses the reasons for waste water treatment and the existing and emerging technologies for meeting NPDES effluent limits. REASONS FOR WATER TREATMENT Due to the diverse nature of the mineral Industry, process/waste water contamination problems as well as processing flowsheets are site specific. However, certain generalizations can be made specific to processing of different minerals: • Acid mine drainage Is a problem at sulfide/coal mines. • Cyanide contamination of water Is a problem at gold processing plants. • Organics can be a problem at mines using flotation oils. • Tolling ponds are generally acidic at sites processing industrial minerals such as silica sand and feldspar. The cost for water treatment Is viewed as an added cost of production. Hence, large mines are moving toward dedicating personnel to management of water resources in order to minimize waste water for treatment. Very often, mines having closed-loop water systems will treat waste water for reasons other than meeting NPDES regulations. These Include situations where process requirements dictate use of high-quality water for separation of minerals, neutralization of acid mine drainage water, and portable water for the mill. WATER TREATMENT TECHNOLOGIES Water treatment process has to be cheap and simple because It has to process large volume, and It does not directly add to the bottom line, namely revenue. The water treatment process development has to be site specific because the contaminants In the water vary from site to site. and discharge limits for water vary from state to state. The current technologies for wastewater treatment have been divided Into the following three areas: • Removal of heavy metals • Cyanide destruction • Scale control A brief summary of the current technology In each area Is discussed below. Removal of Heavy Metals The physical and chemical processes for heavy metal removal are summarized in Table 1. The most common and cheapest approach has been the precipitation of hydroxides at high pH followed by sedimentation and thickening of solids. The remaining solids can be removed by filtration. The pH is adjusted back to neutral, and the water Is discharged. This process is most commonly used wastewater treatment technology in the mining industry. The basic processes can be modified by combining other operations in order to meet the objectives of the specific site as illustrated In the following examples: • AMAX&apos;s Mt. Emmons treatment facility uses Lectro Clear® process where the precipitated solids are removed by electroflotation. • AMAX&apos;s Climax Mine water treatment plant used Ion exchange columns to meet the discharge limits on molybdenum.

Jan 1, 1992

By J. S. Hall

The productivity and fuel efficiency of iron-ore blast furnace operations has greatly increased in recent times. These improvements, particularly to the Japanese steel industry, have primarily arisen from process engineering studies of the blast furnace and associated operations such as sintering. The development of fluxed sinter based on iron-ore fines reacted to produce highly reducible, low slag sinters has contributed further to a reduction in fuel requirements. The Pilbara province of Western Australia is a significant source of these iron-ore fines supplied to the international market. Increasingly, this market is being offered high quality ores from other foreign sources. To technically assist companies in improving the processing efficiency of ores, and to improve the technical marketing of ores by modelling the processing characteristics of Australian/international ore blends, the Commonwealth Scientific and Industrial Research Organization (CSIRO) is actively assisting the industry by researching the general theme of &apos;iron ore from mine to metal in this paper we outline progress towards a numerical description of: a. ore deposit classification. b. Degradation during transport. c. Direct reduction of iron ore. d. Liquid bath ore reduction/smelting. e. Industrial sintering.

Jan 1, 1986

By A. M. Marabini, G. Belardi, V. Alesse, M. Acosta

Sotiel mine is situated in the Iberian Pyrite Belt in southern Spain, some 40 km north of the port of Huelva. Although mining operations at the site date back to Roman times, the present mine came into production in 1983 and 5.6 million tonnes of ore had been extracted by 1993. The orebody is volcano-sedimentary and consists of fine grained copper, lead and zinc minerals in massive pyrite surrounded by slates and volcanics. Prior laboratory research had resulted in the synthesis of a new collector, belonging to the MercaptoBenzoOxazole (MBO) class that acts selectively towards Cu and Zn minerals after activation with CuS04. The MethylMercaptoBenzoOxazole (MMBO) version of this collector had been used for the laboratory flotation of Cu minerals and sphalerite activated by CuS04. This resulted in identification of the optimal physicochemical conditions for laboratory-cell flotation of the two minerals from samples of complex sulphide ores, and subsequently the reagent has been tested in the Sotiel plant (Spain). The plant has three flotation sections. With conventional re-agents, the first section yields a Cu concentrate grading 21% with a total recovery of 29%, and the second one yields a 40% Pb concentrate with total recovery of 34% and a 47% Zn concentrate with total recovery of 78%. Application of the new synthetic reagent in the copper and zinc circuits produces a more selective process with a decrease in re- agent concentration grade and recovery are increased by 2 and 9 points respectively in the case of Cu and by 1 and 3 points where Zn is concerned. Moreover, the penalty elements in the Cu concentrate are halved.

Jan 1, 1995

Abraham E.M., 465 Adam K., 151, 203, 249 Agioutantis Z., 137, 389 Alley M.M., 301

Jan 1, 2007

By Stefano Ceccotto, Eugenio Trussoni

"INTRODUCTION Contemporary city is made of layers. Physical structures layers (built fabric, residential, commercial industrial etc. ), infrastructural layers (below and above ground), “green” layers (parks and open spaces), and also informational layers, i.e. connections, links, between sectors of the city and other territories. The “city of layers” concept represents the exercise of “rebuilding the city” per each layer, highlighting those physical built structures that are functional to define a relation. For example, if consider the “connection” relation, the city is re-designed by considering only transportation built structures. The layer obtained in such fashion is hence the “transportation” layer, including below grade infrastructures (subways) and above grade lines (rail, bus, tramways etc.), as below shown in Figure 1.In this sense, the contemporary city is represented by separate constructs assembled together according to a specific functionality (e.g. “connection”). As a consequence, the relation between what is built underground, and the related above-ground development, can be perceived in his most evident appearance. What could happen within the contemporary city if the planning process would begin from below to above and not vice-versa?INTERACTION The question risen in the introduction is strategic when approaching the difficult task of designing (or re-designing) a multi-level organism like the contemporary city. Nowadays, the theme of integration between underground and at-grade master planning has become the subject of many urban renovation projects, where the design process has begun within the transportation layer, underground, and further developed by interacting with at-grade structures already existing or in phase of design.A series of case studies where below/above interaction plays a key role in the project will be further analyzed. Moreover, it is relevant to understand the mechanics of an urban transformation process that originates within the transportation layer and ends up with the design of entire sectors of the city. The Transit Oriented Development approach is a useful tool to clearly understand such transformation process. TOD has become, in particular in the last decade, one of the most effective tools for urban design, in order to solve simultaneously the many different instances related to transit planning, urban design and real estate market."

Jan 1, 2016

By Brandon Barnes, Michael Haggerty

"Around Minneapolis and Saint Paul, Minnesota, the local geology includes the St. Peter Sandstone, which is easily minable and has facilitated construction of interceptor tunnels for storm water and sanitary tunnels since the 1800s. The elevation of the geologic units allowed gravity-driven flows from the downtown areas all the way to the Mississippi River. Through many years of service, some of these tunnels have experienced degradation and require maintenance. Additionally, increased stormwater surface runoff can result in internal pressurization of the tunnels, accelerating degradation. Because structural failure or collapse of any of these interceptor tunnels would create a significant repair challenge, the city of Minneapolis has been inspecting and designating tunnels in its system for periodic review and repair. One of these, the St. Mary’s/Hiawatha tunnel, was rehabilitated using a grouting program. A hydrologic model was also used to improve understanding of pressurization events during some storms, leading to construction of a near-surface pressure dissipation chamber to provide increased hydraulic capacity. BACKGROUND The St. Mary’s/Hiawatha tunnel in Minneapolis has three segments; the first two were constructed in 1942 and the third was added in 1987 (Figure 1). Segment 1 is approximately 4,700 feet in length and outlets to the Mississippi River. Segment 2 intersects Segment 1 approximately 3,500 feet upstream of the river outlet and continues for approximately 2,500 feet in a southeasterly direction. The third and newest segment is approximately 500 feet long. There are four different cross sections of tunnel along the entire system.Originally, tunnel construction often consisted of mining the St. Peter sandstone with a pressurized water lance and constructing wood lagging support (Payne, 1967). An underdrain was generally installed below the invert during construction; this resulted in localized dewatering and provided groundwater control during construction. Non-reinforced concrete liner sections were cast in place. Often void space existed between the tunnel liner and the native sandstone bedrock. These voids, particularly in the crown, prevent direct contact between the liner and the bedrock."

Jan 1, 2016

By S. E. Phifer

The Haile Gold Mine was the largest gold producer east of the Mississippi River prior to 1942. It is currently the only producing gold mine in the Southeastern United States. Current development involves the mining and heap leaching of some 1000 TPD. Carbon is employed as a recovery medium. Due to its clayey nature and excessive fines in the oxide ore, agglomeration using Portland cement is required prior to leaching. The ore ranges in screen size from two inches to -200 mesh. The agglomerating step combined with certain other conditions has enabled Piedmont Mining Company to achieve recoveries of 90%.

Jan 1, 1987

By Lu Yang

In the last two decades, acid iron ore pellets have established their predominant position as the iron-bearing burden material for blast furnace ironmaking in North America. It is a general practice that pelletization plants are asked to produce pellets of certain chemical composition and in a narrow range of sizes. A minimum amount of fines created during handling and transportation is desirable. Such a requirement is often expressed indirectly by the minimum compression load causing a pellet to break. The behavior of pellets inside a blast furnace, of course, is very important for a smooth and efficient operation. Before its melting in the lower part of a blast furnace during this period of several hours the behavior of pellets depends on their properties after induration as well as conditions inside each furnace. Among properties of indurated pellets, the ability to maintain their physical integrity in the burden and to be reducible are most important. To maintain the integrity of pellets (i.e., minimal low temperature breakdown, swelling and softening) so that there will be adequate overall permeability for certain wind rate and local permeability for gas/solid contact for reduction. A higher reducibility will moderate the adverse effects of swelling and softening and contribute to a smooth operation and efficient use of heat and reductants in a blast furnace. An article devoted to the relationships between the quality of iron ore pellets and blast furnace practice has been published elsewhere(1); therefore, no further discussion is needed here. The mechanism of strengthening of iron ore pellets during firing has been the subject of investigation of many authors(2). There is no doubt that the bridging of the growing hematite grains, particularly starting with magnetite concentrates, is very significant in the production of strong pellets. Recently, there are many reports from blast furnace operators that they have noticed the adverse effect of LTB in their plants. It is obvious that the strength derived from bridged hematite grains may disappear when hematite is converted to magnetite with thorough breakdown of grain structures. It is suggested that some other strengthening mechanism may be required in order to improve the LTB index of acid pellets. The influence of porosity on both compression strength and reducibility follows regular patterns. It has been suggested(1) that the amount of liquid slag in pellets during firing determines to a large extent the porosity, hence, indirectly, strength and reducibility.

Jan 1, 1983

By J. E. Urosek

The Mine safety and Health Administration (MSHA) formed the Mine Ventilation Bleeder and Gob Training Committee in 1993. This committee was charged with developing a training course designed to enhance the knowledge and understanding of practical bleeder ventilation systems. The course will probably include a discussion on the theory behind bleeder system design, an in-depth look at the strengths and weaknesses of the basic bleeder system types, case studies, and a review of the systems currently in use. A database on active underground bituminous coal mines, gob areas, and the bleeder systems presently used was developed from questionnaires distributed to nine Coal Mine Safety and Health (CMS&H) districts. Representative systems were selected for thorough investigation to develop case studies. This paper introduces some of the material to be included in the course, including a description of basic bleeder system designs, a review of a portion of the database, and facts about the gob areas and bleeder systems investigated for the development of case studies.

Jan 1, 1995

By Frank W. Schmechel

The subsidence monitoring program at the Old Ben No. 24 Mine was planned in 1976 as part of the on- going demonstration of longwall mining. The construction and installation of the network of surface subsidence monuments was started in Play of 1976 and completed four weeks later after which an initial reference survey was made of all surface monuments. Mining of the first longwall panel started in September of 1976 and was completed in May of 1977. Mining of the second panel started in August of 1977 and is continuing at this time. The Automatic Data Acquisition System (ADAS), which is the subject of this paper, was installed over the second panel on March 29, 1978 near the panel center (Figure 1) and approximately 104 meters (370 feet) in front of the face position at that time. Mine No. 24 is located approximately 5 kilometers (3 miles) Northwest of Benton, Franklin County, Illinois. Coal is being mined from the Illinois (Herrin) No. 6 seam which is at a depth of about 189 meters (620 feet) at the site. The Herrin No. 6 is up to 2.7 meters (9 feet) thick in the mine but a constant thickness of 2.1 meters (7 feet) is being mined by the demonstration longwall with both roof and floor coal being left for stability. Although the seam is flat laying at the mine, it dips north- ward regionally. Topographically, the surface over the demonstration panels is essentially flat and low laying with several areas of standing water. The Rend Lake Dam (United States Army Corps of Engineers) is about 305 meters (1000 feet) north of the demonstration site.

Jan 1, 1979

By J. Stowe

While there has been continual improvement in the models for predicating deposition velocity and pipeline friction losses, the fundamental design philosophy for tailings pipelines has remained the same over the previous three or four decades: design the tailings pipeline to operate in turbulent flow without a deposit on the pipe invert for all expected process conditions. Recent improvements in the understanding of slurry pipeline flows allows for the design of pipelines operating with a deposit on the pipe invert, allowing the system to operate at moderate velocities for high flow rates, optimizing system energy requirements and maximizing pipeline wear life. Tailings pipelines are increasingly operated at higher solids concentrations where there is a greater likelihood the pipeline will operate in laminar flow due to the higher tailings slurry rheology. Historically, slurry pipelines have been operated in turbulent flow. We now know that laminar flow pipeline operation is possible as there are several operational laminar flow tailings pipelines. While our understanding of laminar flow slurry pipelines is not complete, recent research provides guidance on how to approach the design of these pipelines. New sensor technology has led to the development of an instrument that provides reliable indication of bed deposit height within a pipeline. This technology is particularly helpful in operating pipelines with a deposit and has application in better understanding the operation of laminar flow pipelines. Failure of tailings pipelines can result in consequent damage to surrounding structures and unacceptable spillage into the environment. Modern pipeline leak detection technology allows operators to better manage this risk by ensuring safe and reliable operation of tailings pipelines. This paper provides an overview of the each of the above advances in the design and operation of tailings pipelines. OPERATING TAILINGS PIPELINES WITH A DEPOSIT Tailings pipelines, and slurry pipelines in general, are typically designed to operate without a deposit on the pipeline invert. Meaning, the minimum operating velocity exceeds the turbulent deposition velocity. This approach has been adopted due to concerns regarding potential blockage of a pipeline operating with a deposit. Figure 1 shows a typical design duty envelope for a tailings delivery system as a function of solids throughput and solids concentration by mass. If the pipeline is designed to operate without a deposit at the lowest duty flow rate (4,480 m3/h), the operating velocity at the highest duty flow rate (6,590 m3/h) is about 1.5 times the deposition velocity. Considering that the pipeline wear and energy requirements are roughly proportional to the square of operating velocity, this results in an operationally inefficient system when the pipeline is operated close to the maximum design flow rate. Most systems tend to operate at maximum throughput after post-startup debottlenecking optimizations. Alternative Approach An alternate design approach is to ensure the pipeline operates without a deposit for the nominal flow rate and accept that a deposit will form when operating at lower flow rates. This results in the selection of a larger diameter pipeline, but there are significant benefits in terms of reduced energy requirements and lower pipeline wear.

Jan 1, 2019

By W. A. Haley

As far back as 1939 state laws have required reclamation of mined lands. Reclamation has been the topic of many discussions and presentations, especially since the late 1960&apos;s. In the past ten years many states have added legislation concerning the reclamation of coal-mined lands. In the near future, it seems certain that some federal regulations will be passed that will set minimum guidelines for the states to regulate. Besides the requirement of returning the land to the approximate original contour, future regulations will more than likely demand replacing topsoil from one to five feet thick. As regulations become more stringent, costs will rise accordingly. Since no one has developed a machine that can do all reclamation work by itself, it is necessary to review in detail the tools available and to select the most economical means.

Jan 1, 1976

By L. Nahai

In an exchange of views with the Program Chairman for the Technical Session on Industrial Minerals and Investment in Foreign Countries, it was agreed that it would be more interesting to approach the problem of mineral investment in foreign countries in a more general framework and not confine it to industrial minerals. Therefore, this Bureau of Mines report is proposed to examine current attitudes toward investments in foreign mineral resources and restraints that they impose on investments necessary to assure supply for future global mineral needs.

Jan 1, 1976

By James P. Odendahl

Missouri is a state rich in mineral commodities. There is a variety of types of mining as well as minerals in the state. Different phases of mining are controlled by a variety of state and federal laws. What I hope to do today is to present briefly some of the interaction and interplay that has occurred in the recent years between the mineral industry and the Missouri regulatory agencies, as well as some of the interactions by federal agencies. First a little history which dates back to the late 1600&apos;s. For many years Missouri has been a leader in the production of lead and zinc. In fact, recent studies have indicated that Missouri produces better than three-fourths of the nation&apos;s present lead supply. Less well known but important resource is iron mining. Some of these operations were the source of confrontation during the Civil War. Major battles were fought in and around Ironton, Missouri where iron mining has occurred for many years. One of the largest pelletizing operations in the state is currently located within the city of Ironton. Joplin, Missouri, the home of Thomas Hart Benton, the famous Missouri painter, has a history of lead and zinc mining, going back to the later 1800&apos;s. Many of the paintings by Benton contain reference to the early days of mining in Missouri. There is a Benton mural in the City Hall at Carthage depicting the early days of lead mining in that area. Later, the center of lead mining moved to southeast Missouri near Bonne Terre and Flat River. The names of the towns in this area reflect the history of mining, examples - Leadington, Old Mines, Rivermines, etc. The history of lead mining in Missouri has been referred to in some detail in various publications(l).

Jan 1, 1977

By Bernd Hagenah, Eric C. Wang

New tunnels of significant alignment lengths such as mountain tunnels, base tunnels, as well as beneath urban centers pose unique environmental challenges. This paper highlights key environmental considerations for planning, design, construction, and operations by sharing lessons-learned from the authors' extensive project experience on these types of tunnels. Discussion of unique constraints include limited right-of- way, ventilation and emergency egress during the construction phase and revenue service, safety and security, and protection of existing structures. Practical approaches and applied innovative state-of-the-art solutions addressing distinct sustainability challenges and unique requirements are shared from US and international project examples.

Jun 23, 2024

By N. Mehrshad

Research and experience have demonstrated that the operating conditions of the flotation process are reflected in the froth?s appearance. Despite recent advances in image analysis and several algorithms developed for froth flotation, there still is not a comprehensive algorithm to accurately determine bubble features from actual froth images. Being able to accurately and automatically measure bubble size distribution is an important requirement for optimization and control of the flotation process. Segmentation is one of the most effective approaches for accurately determining the bubble size distribution. In the present study, a new bubble segmentation algorithm, which utilizes an adaptive marker-based watershed transform, is proposed to measure the bubble size distribution from froth images. The developed algorithm is validated using some industrial scale froth images from flotation cells at different duties.

Jan 1, 2011

By P. G. Kovalchik

Recent research conducted by NIOSH, Pittsburgh Research Laboratory showed that electrical current levels permitted under present regulations may not limit cable temperatures to less than 90°C in reeled trailing cables. Reeled cables, tightly wrapped with many turns, all carrying current in an enclosed space, can become overheated due to poor heat transfer. This overheating can cause the cable insulation to soften and become easily damaged. The damaged insulation reduces the life of the cable and can lead to shock, electrocution, and mine fires. This paper describes a method of measuring the conductor temperature of mine trailing cables during normal operation. The temperature is measured using a 50/125 micrometer Graded Index Multimode Optical Fiber located in the center of the metallic conductors. Distributed temperature measurements are made using an Optical Time Domain Reflectometer (OTDR). This system is capable of measuring temperature with an accuracy of plus or minus one degree centigrade over a length of 4 km at 1-m intervals. With this unique way of measuring temperature, tests can be conducted simulating actual mine conditions and provide important data to allow MSHA&apos;s Approval and Certification Center to develop approval criteria for cyclically rated reeled machines.

Jan 1, 1998