Search Documents

By D. R. Nagaraj, Napoleon Tercero, Raymond Farinato

Historically, as for most reagents used in flotation, the wide-spread use of dialkyl dithiophosphinates as collectors in practical applications has preceded a detailed scientific understanding of how they work. Dialkyl dithiophosphinates are a technologically and commercially important class of collectors used in the flotation processing of Cu-Au, complex polymetallic, and precious metal ores. Plant usage has demonstrated that dithiophosphinates exhibit higher selectivity and flotation rates for Cu sulfides, galena, and precious metal values in the presence of other gangue sulfides, than the traditionally used collectors such as dialkyl dithiophosphates and xanthates. They also have an attractive health, safety, and environmental (HSE) profile. Although dithiophosphinates received little attention in the past in the flotation research community, recently, there has been significant interest in this chemistry, and numerous studies have been conducted to understand the fundamental interactions of dithiophosphinates with several base metal sulfides and precious metals. A critical overview of fundamental studies, laboratory ore flotation, and plant practice of dithiophosphinates is given in this paper. The findings from these studies are rationalized and explained by drawing on concepts and insights from coordination chemistry. A comparison between the interactions with various minerals and metals of dithiophosphinate and dithiophosphate analogues brings out some of the subtleties that seemingly minor changes in collector chemistry can make. The critical overview and analysis given here is useful in identifying gaps in knowledge regarding this important class of compounds. This in turn can provide a basis for the design of studies to advance our understanding of dithiophosphinate flotation performance.

By Todd Schrauf, James Scott, Mark Smith

"Cyanide heap leaching of gold ores in areas with extremely low winter temperatures requires special considerations to prevent freezing of the leach solution. Factors that impact the solution temperature include ore temperature at the time of stacking and during operation, burial of drip irrigation lines, use of geomembrane covers and heating of the leach solution. Thermodynamic modeling was performed to simulate expected ore and solution temperatures under different operating strategies for Kaminak Gold’s Coffee gold project in the Yukon Territory. Mean monthly temperatures at the site ranged from a low of -22.5 °C (-8.5 °F) to a high of 13.6 °C (56.4 °F), while in situ ore temperatures ranged from -0.5° to about -1.5 °C (31 ° to 29 °F). The modeling results were used to optimize the operational parameters and indicated that a combination of drip line burial and heating of the leach solution during the winter months was required to maintain solution temperatures above freezing during the initial years of stacking, although as the size of the heap increased, heating was no longer necessary.Modeling objectivesThe successful operation of a cyanide heap leach under extremely cold winter temperatures requires the implementation of operational strategies to prevent freezing of the leach solution and the ore within the heap. Thermodynamic modeling of the heap provides the means to quantify the effectiveness of these different operational parameters on maintaining the required operating temperatures to avoid freezing within the heap. The operational parameters that were evaluated with the model included:"

Apr 1, 2016

By Jacek B. Stypulkowski

This paper discusses the challenges faced by the design team of the under-river crossings of electric transmission feeders in New York City, a densely populated urban area. The under-river crossing of a 345 kV feeder was initially designed as Horizontal Directional Drilling (HDD), but was redesigned as a utility tunnel because of site con¬straints on both sides of the river. Multiple studies addressed location, available tech-nologies and costs. Multiple soil investigation phases addressed design aspects of HDD, as well as tunneling. Contractual issues varied from a design build alternative with Geotechnical Data Report (GDR) to design tender approach with GDR & Geotechnical Baseline Report (GBR).

By Rolf Birger Pedersen, Alden Ross Denny

"Synthetic Aperature Sonar (SAS) is a powerful tool for ultra-high resolution marine survey. The Kongsberg HiSAS system deployed on the HUGIN AUV has a rangeindependent resolution of 3x3 cm for sonar image and ~10x10cm for the interferometric bathymetry product [1]. This resolution is achievable for areas up to 50 km2 on a single survey mission providing huge multi-attribute datasets. This technology, originally designed for military and oil-industry applications, has the potential to revolutionize scientific seafloor mapping. The extreme resolution of this technique allows for deposit mapping in and around seafloor hydrothermal systems, including the discovery of extinct venting structures. By clearly distinguishing between volcanic and hydrothermal landscapes based on features below the resolution of conventional multibeam systems, SAS enables an entirely new level of hydrothermal deposit survey. Additionally due to the extreme resolution of this survey technology, repeat survey and change detection should allow centimeter-scale changes in deposit morphology to be routinely detected over an entire hydrothermally venting region. In collaboration with the EU funded MIDAS project, the Centre for Geobiology at the University of Bergen will deploy the HUGIN AUV this summer at two distinct shallow venting systems on the Arctic Mid-Ocean Ridge system. The AUV will collect repeat bathymetry at the Jan Mayen Vent Field, and extend the SAS coverage to include newly discovered venting sites. We will present the preliminary findings of this expedition, including the first deposit estimations made from full-resolution SAS mosaics."

Sep 1, 2014

By A. D. S. Gillies

The use of refuge chambers for use in handling underground emergencies is an issue of topical relevance within the US mining industry. Chamber design is of importance to meet some new safety requirements of US federal and some state government mine regulations. A review has been undertaken of a steel mine refuge chamber design to predict what will be internal temperature within the chamber over an extended period with miners present? The design has been examined for the situation when the chamber is sited in still mine air. Spreadsheets have been developed to allow various design assumptions to be tested. The evaluation has been undertaken using thermodynamic heat transfer models with some assumptions specified to produce a model of appropriate simplicity but with adequate degree of accuracy. Under normal still air conditions it can be seen that internal chamber conditions rise quickly to often arduous conditions. There will always be quite a few assumptions necessary in complex heat transfer process evaluations. Some important refuge chamber design parameters are: ? External surface area of the chamber, its wall thickness and construction. ? Metabolic heat generated and number of persons making use of the chamber. ? The temperature of the external mine atmosphere to the chamber over the year and the influence of geothermal gradient on temperature at depth. ? The maximum internal chamber Apparent Temperature considered safe. ? The distance inside the underground mine and adjacent ventilation conditions.

Jan 1, 2012

By R. Snoby

Since its introduction in 2002, the modern air jig has processed a wide array of coals throughout the world. This paper explores the reasons and justifications for the installations and provides case history performance data. Specifically highlighted are air jig plants processing metallurgical coal in Colombia, bituminous coal in the United States and India and lignite in the United States and Spain. Each installation has unique reasons to justify an air jig facility. It is important to note that not all of the justifications were based on the ?most cost effective yield?, normally a mantra for coal preparation plant designers and owners. Dry jigging of coal has long been a proven technique for upgrading coal, the modern air jig, with its improved efficiency and operating systems simply extended the range of applications. In some cases, it even allows market quality coal to be produced when no other option is possible.

Jan 1, 2009

By Nasser Madani, Yerbol Tussupbekov, Sergei Sabanov, Zarina Mukhamedyarova

A case study was conducted on a metal mine operating in Kazakhstan, in which problems were associated with use of a complicated and outdated ventilation system and its high expenses. The mine needs to reconsider its existing ventilation system and identify the risks associated with operational losses when using this ventilation system. The aim of this study was to develop an efficient risk analysis method capable of estimating operational risks and financial benefits of the existing mine ventilation system. The developed risk analysismethod considers ventilationmodelling, riskmodelling, and financialmodelling.Ventilation modelling comprises ventilation simulation and ventilation financial simulation. In risk modelling, the number of risk events occurring with the use of existing ventilation system and the operational losses during these events is estimated. Financial modelling considers operational losses and ventilation financial simulation benefits and uses a dynamic cash flow model to estimate how cost variability influences the cash flow. As a result, the improved ventilation system attains an additional NPVa ranging from 3.2 to 8.5 million US$ at the corresponding defined probability of 90%. The results of this study reveal that the developed risk analysis method can efficiently estimate the financial benefits of ventilation modelling and consider risk events and their total operational losses associated with use of the existing ventilation system. This approach provides a range of possible outcomes and helps with deciding whether the ventilation system is appropriate or whether it should be updated to better suit the project financial benefits.

Jun 3, 2020

By Bhaskar B. Thapa

The design of the Caldecott 4th Bore, located along State Route 24 in Oakland, California, is based on the principles of the New Austrian Tunneling Method (NATM). Typical NATM initial support design practices used in Europe were adapted for this project to account for U.S. conditions and requirements, such as degree of experience with NATM construction, the prevailing contractual environment, and preferences for contractual simplicity. Key design features are: (1) support selection criteria based on ground behaviors and ground conditions; (2) a prescriptive design with allowance for support adjustments based on observations during construction; and (3) organization of support requirements into only four major support categories, while permitting some adjustment for variations in ground behaviors and conditions using a few subtypes and additional support measures.

The Forestry Reclamation Approach (FRA) specifies that the upper 1.22 m of material on the reclaimed surface should be left as uncompacted as possible to facilitate tree root growth. One of the main concerns about applying the FRA to steep slopes is that the upper 1.22 m of material could cause the reclaimed slopes to be unstable. Successful application of FRA on flat and rolling surfaces precipitated this investigation. Details of a field investigation conducted at a steep-slope mine are available in an earlier publication (Kumar and Sweigard, 2011). A total of 70 survey monuments were driven into the slope in a regular pattern to monitor slope movement. Quarterly surveys of the monuments were done to quantify any type of mass movement either horizontally or vertically. The methodology proposed for slope movement was verified using numerical models. Analytical models based on limit equilibrium technique and numerical models based on the finite element method were developed for slope stability analysis. The limit equilibrium analysis was done using Geo-Slope software following the Simplified Bishop Method. The finite element (FEM) numerical model was developed using the Plaxis computer program following the strength reduction technique. Two kinds of slope stability analysis were performed: first with the top 1.22 m of loose material and second without top loose material. Finally, the field investigation results were compared with stability analysis results. Both of these approaches showed that application of the FRA on steep slopes is not causing any significant instability problems that would not exist otherwise for overly steepened slopes. Keywords: Forestry reclamation approach, steep slope, slope movement, factor of safety

Feb 27, 2013

By Snehamoy Chatterjee, Sanjay Kumar Palei, Smarak Das

Machine manufacturers’ recommendations on maintenance strategies of capital-intensive draglines are not always based on real data and therefore lead to losses from downtime. This paper proposes a preventive maintenance strategy for a dragline deployed in an opencast coal mine based on reliability-centered maintenance and failure-mode-effects analysis using real operational data. Reliability-centered maintenance replaced a cluster of critical failure components of the dragline while satisfying two specific conditions: (i) the components should be replaced at the earliest mean time to failure (MTTF) within the group and (ii) the time taken to replace all the parts should be equivalent to the maximum downtime within the group. Estimated threshold weightage factor identified twenty-six critical failure components for the preventive maintenance strategy, and clustering of components divided them into nine groups. In a group, the loss that is expected to occur by replacing some of the components before their failure, and the gain by reducing the overall maintenance downtime, has been explained through a cost-benefit analysis. The total net profit generated is calculated as US$200,178. This clustering activity also led to a reduction of annual downtime by 231 h, whose approximate market price as equivalent coal production costs $295,365.

May 28, 2020

The recovery of coarse particles has been widely recognized as being limited by the froth in mineral flotation. In response to this, FLSmidth has developed the Selective Froth Recovery (SFR) System. The SFR System is an extraction system that vacuums material from select locations within the froth and separates the recovered solids into coarse and fine fractions with a hydrocyclone. The SFR is supported and located by an actuator connected to the cell?s level control so that the suction heads are maintained at an offset distance from the slurry level. This can increase the recovery of coarse material by selectively recovering the material close to the bottom of the froth where drop-back of coarse particles typically takes place. The SFR System has been tested at two separate mine sites, and has been proven to increase the copper recovery in both trials. TEST RESULTS The SFR prototype was installed in a copper recovery circuit, on a rougher scavenger 160-m3 flotation cell. Figure 1, shows the SFR System, which consists of four conical skimmer heads that are plumbed together and share a common actuator. The SFR System, raised out of the froth prior to a test, can be seen in Figure 2. The SFR prototype was able to maintain a variety of set points using the level control to determine the slurry height.

Feb 27, 2013

By M. A. Reyes, L. Yan

Heat and humidity buildup within refuge alternatives (RAs) may expose occupants to physiological hazards such as heat stress. The Mine Safety and Health Administration (MSHA) regulations require RAs in underground coal mines to provide a life-sustaining environment for miners trapped underground when escape is impossible. RAs are required to sustain life for 96 h while maintaining an apparent temperature (AT) below 95 °F (35 °C). The National Institute for Occupational Safety and Health (NIOSH) tested a 10-person tent-type RA, a 23-person tent-type RA, and a 6-person metal-type RA in its underground coal mine facilities to investigate the thermal environment over a 96-h period. The test results showed that mine air and mine strata temperatures surrounding an RA occupied by simulated miners (SMs) increased over the 96-h test period. The test results suggest that RA manufacturers should consider this increase in temperatures when calculating and evaluating RA components during surface and laboratory tests. The findings can equip stakeholders with additional considerations for calculating the interior heat and humidity temperature profiles for occupied RAs not tested in situ

Nov 22, 2019

By A. B. Cecala

Over the past decade, a substantial effort has been made to improve the air quality inside enclosed cabs of both underground and surface mobile mining equipment to reduce respirable dust exposures to the equipment operators. As part of this effort, the National Institute for Occupational Safety and Health, (NIOSH) completed a comprehensive laboratory study which determined the significant factors for cab filtration and pressurization systems. From this information, a major underground mining equipment manufacturer designed a filtration and pressurization system which was incorporated into the enclosed cabs of its equipment. A long-term evaluation was performed on the effectiveness of this filtration and pressurization system to improve the air quality in the enclosed cabs of two different pieces of equipment, being a face drill and a roof-bolter machine, at an underground limestone mine. This long-term evaluation demonstrated a significant reduction in dust levels comparing outside to inside cab respirable dust concentrations. During this evaluation, a modification to remove one of the filters on the roof-bolter machine simplified the design without sacrificing the system?s efficiency. Testing using particle count instruments performed during non-production time periods on both pieces of equipment indicated Protection Factors greater than 100 when comparing respirable-sized dust particles inside the enclosed cab relative to outside.

Jan 1, 2012

By Nikhil Dhawan, Shrey Agrawal, Veeranjaneyulu Rayapudi

India’s steel vision of 2030 requires a huge amount of quality iron ore. The utilization of low-grade iron ores such as banded iron ores will play an important role to achieve the same production. The absence of alumina impurities in the banded hematite jasper (BHJ) ore provides it an edge over other low-grade iron ores. The conventional beneficiation techniques such as magnetic separation and washing were found to be ineffective to produce suitable feed (Fe ~ 60%) for the blast furnace. It was found that microwave exposure provides significant enrichment to the low-grade iron ore and can be used as a pretreatment step in the beneficiation of similar low-grade iron ores. The above study reveals that hematite phase is susceptible to microwave exposure which enhances the separation of iron values from impurities. Under optimum conditions, an iron-enriched concentrate with 61% Fe, 85% Fe recovery at 50% yield can be achieved from BHJ feed ~ 38% Fe. The pretreatment process for BHJ beneficiation includes only microwave exposure without any chemical additive and may prove economical and industrially feasible.

By C. Meyer, J. J. Eidel

C. W. Hunt I wish to register strong disagreement with the choices of drilling sites chosen by the Continental Scientific Drilling Committee, while endorsing the stated objectives. Of special significance is the lack of any site involving the metals most needed today in the US, while 9 to 13 km of drilling are allocated to gold and silver districts and 11 to 17 km to base metal (mainly copper) districts. Why is nothing proposed for platinum group or chromite? Is this because the committee did not know of such a site? If so, I offer such a site in California (see Fig. 1). The mineralization shown in Table 1 occurs in a large peridotite body in western Tehama County, CA. Petrography has demonstrated unequivocal evidence of migrated PGE deposited in peridotite and chromite of hypabyssal nature. Active diapirism (due probably to serpentine buoyancy) above a reactivated mantle to surface conduit marks the position of the conduit. Young explosion breccia cemented loosely by volcanic glass and tuff demonstrates the significance of the conduit as the prime source of the various emissions. Deep drilling could result in major metals discoveries as well as shedding light on the grand questions of platinum group mineralization. What role water has played in this occurrence is not yet certain; but chlorine and asphaltite have been detected in and adjacent to native PGM, suggesting a major role for water. The explosion breccia suggests that this excellent site could overlie entrapped geothermal steam.

Jan 6, 1987

By R. J. R. Cornelissen

The elimination of the incidence of silicosis in employees in industries such as mining and pottery is an ongoing international initiative. After many decades of industrial activity in these industries and many dollars spent on preventative measures, silicosis is still occurring. The exposure-prevention measures taken so far have certainly improved the working environment dust concentrations; however, the illness is still regularly diagnosed in workers. More funding is needed for interventions to improve working conditions. Many aspects of dust prevention and suppression will be researched and exposure assessment methodologies and equipment will need to be reviewed for the purposes of improvements in effectiveness. This paper presents results from laboratory tests carried out on gravimetric sampling pumps and cyclones. It highlights the erratic flow produced by gravimetric pumps of three different manufacturers who claim their respective pumps are equipped with flow stabilisers. The standard BS EN 1232:1997 is used as a basis for the tests. A method, albeit impractical for fieldwork, is shown for the elimination of the pulsation in the flow. This method serves to prove the method and protocol used in this study. The pressure loss caused air-flow resistance of cyclones is measured. The air inlet aperture size of cyclones is measured. The large discrepancy in the two criteria between individual cyclones is shown. The paper concludes that all the pumps tested failed the prescribed limits of BS EN 1232:1997 regarding the pulsation of the gravimetric sampling flow. The difference in flow characteristics of the cyclones, together with the erratic flow produced by the pumps, throws into question the accuracy of the exposure assessments. It is suggested that substantial resources be channelled towards solving these flow problems in parallel with measures taken to reduce exposure. In principle, the accurate assessment of exposure and dust concentration levels is a prerequisite for effective management of the problem of silicosis.

Jan 1, 2009

By S. K. Oraee

Most management decisions at all levels of the organization are as directly or indirectly depends on the circumstance of future. With regard to predict the future events in the process of decision-making plays a main role, therefore, forecasting is very important for every organizations and institutions. There is a variety of methods to predict time series. In general, these techniques can be divided as following: statistical, artificial intelligence and analytical techniques. Two of the most common methods for time series prediction is autoregressive integrated moving average (ARIMA) and artificial neural network (ANN) methods, these methods are the subset of statistical and artificial intelligence techniques respectively. In this paper, a hybrid model of ARIMA and ANN models are employed to predict the number of fatal injuries in the USA underground coal mines. This research showed the result of hybrid model is better than split model.

Jan 1, 2011

By John M. Dale

Now that the price of sulfur has reached unexpected high levels, it is little wonder that sulfur from surface ores is again receiving attention. In most instances, it is advantageous for an ore to be at or near the surface. However, it is a distinct disadvantage for sulfur ore to be close to the surface because it precludes the use of the Frasch process. The Frasch process depends on the presence of at least 180 m of uniform overburden to allow pressure injection of superheated water into the sulfur-bearing formation to melt the sulfur. In the Frasch process, sulfur separates cleanly from the gangue underground and comes to the surface in a very pure form. Surface sulfur deposits, particularly those in the Western Hemisphere, exist largely due to volcanic activity, and sulfur separation from the gangue is a formidable technical problem. None of the surface deposits are large compared to some of the Frasch deposits, but at the present sulfur price, they are certainly of economic importance. From the turn of the century until 1975, the price of sulfur was for the most part $18-$28/t. However, with the price of sulfur now over $154/t, there are a variety of technical alternatives to consider for sulfur surface ore separation that may not have been economically attractive a few years ago.

Jan 9, 1981

By D. W. Leyshon

The fluidized solids technique for the calcination of phosphate rock has been well established for over 10 years. This paper is intended to review the recent performance of many of the Dorr-Oliver FluoSolids* calciners. In addition, design features of these three compartment refrac¬tory construction reactors will be described and a comparison made with fuel requirements for single compartment calcination. Also presented will be certain, aspects of the use of the rock including a discussion of non sulfate sulfur in the rock. A system is described for producing a blended mixture of calcined and uncalcined rock.

Jan 1, 1972

By R. T. Langland

The U.S. Bureau of Mines has conducted underground tests and computer analyses to study coal mine roof behavior. Southern Ohio Coal Company provided test sites it) their Heigs mines located near Athens, Ohio. Testing apparatus was adapted for monitoring roof behavior at the face of mining from a remote surface location. Finite element analyses were applied to study the structural conditions present. Test sites were located at three different intersections of entries and crosscuts of the room-and-pillar mine. Electrical read-out instruments were used to record roof bolt loads, roof sag, and roof-floor convergence. They were installed during the roof bolting cycle of a conventional mining section and data was recorded for several months. Normal mining operations continued throughout the test period with minimal interruptions due to the installation and monitoring of the instruments. A computerized data acquisition system, partly underground, partly on surface, permitted continuous monitoring of data and its retrieval, display, manipulation, and storage. The finite element code used to model the test sites accounted for three-dimensional geometry, nonlinear material behavior, and the mining excavation and bolt installation sequences. Results of the test are highly variable. Comparable values between test and analysis results were obtained by applying statistical averaging of. roof test data. Results of the analyses indicate that bolts have a lesser effect on the gross behavior of mine roofs than has been indicated and that bolt load changes are strongly influenced by mining excavation sequence, bolt-placement sequence, and face distance

Jan 1, 1977