Search Documents

By Marcos Vieira, Gil Vilela, Wanderson Silvério, Livia Faustino, Pierre Fernandes

New global industry standards and regulatory changes regarding mining tailings management are driving installation of tailings filtration plants to decommission existing tailings dams and implement dry stacking. Target of this project was to reduce ultrafine slime tailings deposition. Previous investigation at Samarco concentrator has showed a 35% decrease in tailings filtration throughput when feeding a mix of 95% flotation tailings with 5% slime tailings (compared with 100% flotation tailings), also worsening geotechnical aspects such as material workability during dry staking. Industrial trials using a proper filter aid at tailings filtration plant feeding a mix of 94% flotation tailing and 6% slime tailing (equivalent to 30% of total slime generation) have provided filtration performance maintenance (throughput and cake moisture), and dry stacking the dewatered material. Results achieved will enable life expansion of existing slime disposal structures, as well as potential life of mining extension. Furthermore, reagent chemistry influence is discussed by the light of geotechnical aspects, which has been showing improved KPIs, such as workability, compressibility and permeability.

Feb 1, 2025

By P. Zhang

This paper gives a review of promising technologies for phosphate processing, and covers flotation, analysis and process control, as well as tailings treatment and utilization. Air bubbles of less than a µm in size, combined with relatively large bubbles, have been demonstrated, both in the lab and on a pilot scale, to improve flotation dramatically, by reducing reagent use while improving product grade. Innovative use of polymers has allowed rapid dewatering of fine tailings with a final product that does not segregate. The first online laser-induced breakdown spectroscopy (LIBS) analyzer was created, allowing rapid analysis of wet samples using the laser technology. Many large commercial projects are successfully pursuing the utilization of phosphogypsum.

Feb 1, 2012

By Stanley J. LeFond

The Republic of Botswana, one of the newer countries of southern Africa, attained independence on September 30, 1966. It covers an area of about 225,000 square miles (582,000 square kilometers) which makes it slightly larger than France, or slightly smaller than Texas. It is bounded by Zimbabwe, the Republic of South Africa and Namibia, including the Caprivi Strip. Angola and Zambia are close neighbors. (Map 1). Botswana lies at the center of the southern African plateau at a mean elevation of 3,300 feet (1,000 m). It is a natural habitat for most species of African fauna. The rolling sands and extensive grasslands of the Kalahari Desert cover the southwest. The climate is sub- tropical. Summers, although tempered by north- easterly breezes, are hot, but mean maximum temperature seldom rises above 100°F (38°C). Winters are dry with wide temperature variations, which often give rise to frosts.

Jan 1, 1981

By HASAN SERKAN GOKCEN, SERKAN CAYIRLI

The purpose of this study was to investigate the dry grindability of calcite powders in a vertically and horizontally orientable laboratory batch type stirred mill. The experimental results were evaluated using stress intensity analysis. The performance was also compared in terms of mill orientation. The results showed that the d50 values decreased with increasing stress energy down to a certain point and then increased for both milling orientations. Even though the optimum stress energies for both vertical and horizontal orientations were in the range of 1*10−3 to 5*10−3 Nm at 750 and 1500 kJ/kg energy consumption, the product size was finer for the horizontal orientation at the same stress energy value. Additionally, to the best of the authors’ knowledge, this is the first study to compare mill orientation (vertical vs. horizontal) for the same mill and under the same test conditions.

Apr 21, 2021

By George E. Valadão, Iván A. Reyes, Mizraim U. Flores, Armando C. Araujo, Rubén H. Olcay

Dewatering tailings to higher grades than paste produces a stable deposit that typically does not require retention dams and is called a “dry stack.” A proposal of different dewatering techniques applied in the fine tailings produced after final desliming phase, obtained from the treating of phosphatic ores, is the main objective of this work. The dewatering techniques evaluated were column thickener, deep cone classifier, and hyperbaric filtration. Calcite and dolomite were the main mineral contained in the phosphate tailings and these have a very fine granulometry; the tailings presented different behaviours related to the dewatering technique applied. The test column thickener and deep cone classifier with the best operational parameters found to obtain a maximum percentage of solids in mass were ~ 71% and ~ 67%, with values of yield stress ~ 200 Pa and ~ 100 Pa, respectively. In the hyperbaric filtration, a cake with ~ 10% moisture was obtained. This indicates that the transportation conditions are not the same. The overflow turbidity levels obtained from column thickener and deep cone classifier test did not exceed the value 100 NTU, whilst for the filtrate of the hyperbaric filter obtained values ~ 800 NTU. It was possible to preliminary estimate the recovery direct of water, considering each dewatering technique for final disposal of the tailings. The best dewatering techniques obtained were in the following order for the disposal in phosphate fine tailings dams; the hyperbaric filter showed an excellent dewatering capacity with productions rates around 160 kg h− 1 m− 2 for moisture cake of 10%, followed by the column thickener and deep cone classifier with paste ~ 71% of solids (W/W) and high-density slurry ~ 67% of solids (W/W), respectively.

Dec 23, 2023

By Alistair James, Mo Shahsavari, Leon Botham

The 1889 Johnstown Flood, which killed 2,209 people, was a preventable disaster stemming from systemic decisionmaking failures. This paper applies modern Risk-Informed Decision Making (RIDM) frameworks to analyze the historical context and explore alternative outcomes through hypothetical multiverse scenarios. By reconstructing the risk landscape of the South Fork Dam, we demonstrate how structured hazard identification, risk assessment, and stakeholder communication could have mitigated or prevented the catastrophe. Three counterfactual scenarios—proactive maintenance, community engagement, and regulatory oversight—are evaluated to quantify potential lives saved and economic benefits. The study acknowledges historical barriers, including technological limitations, lack of governance, and socioeconomic disparities, which constrained risk-aware decisions in the 19th century. The analysis draws critical parallels to contemporary engineering challenges, particularly in tailings storage facility (TSF) management, where similar risk blind spots persist. The paper concludes that RIDM is not merely a technical tool but a governance imperative, essential for ethical and sustainable engineering practice. By learning from historical near-misses and failures, the modern engineering community can strengthen resilience and accountability. This work contributes to the growing body of retrospective risk analysis, offering a methodological framework for applying RIDM to historical disasters to inform future safety standards.

Feb 22, 2026

By Fabrizio Fara

The Ship Canal Water Quality Project (SCWQP) includes a 2.7-mile long, 18'-10" internal diameter tunnel which is located inWest Seattle. Tunneling in urban areas and soft ground conditions (Till and Till-like soils in Seattle) is associated with the risk of settlements, especially in presence of groundwater above the alignment. The Designer foresaw the use of soil improvement (jet grouting) outside of the launch shaft to mitigate the risk of flowing ground and to provide a redundant sealing. The Contractor proposed and ultimately successfully executed a different approach by using a “Steel Bell System” or Pressurized Can as described in this paper.

Jun 13, 2023

By Sahendra Ram, Ashok Kumar, Rakesh Kumar, AMIT KUMAR SINGH, Dheeraj Kumar, Arun Kumar Singh, Rajendra Singh

This paper describes the successful mechanized extraction of coal pillars in 11 panels using the fish-tail method from 2010 to 2017 at Pinoura Mine in India. This method proved its potential of coal recovery with efficient strata control under weak roof due to faster rate of extraction in a single lift. Observations of strata and snook behavior during the field studies in different panels of the mine are included.

By K. J. Ashley

Over the last six years I have been involved with the calculation of ore reserves and mine planning using various computer systems and soft- ware packages. This experience has given me a unique perspective from which to view the needs of the engineers and geologists whose job it is to produce geologic and mineable ore reserves. The purpose of this paper is to share that perspective with those who are in this field or are thinking of purchasing computer software to aid in these calculations. My first experience with computers in mining was the creation of a mini-computer based coal reserve and mine planning package written as part of my Easter's thesis. This package took about ten weeks to write, four weeks to document, and two weeks to install at the mine for which it was written. It did what it was designed to do, which was to emulate the hand procedure which had been used prior to its installation. The package was specific to its application which involved several small seams of coal being mined simultaneously and would have required major modification for it to be applied to a mine where, say, one thick seam was mined in two benches.

Jan 1, 1985

By Aixiang Wu, Minjie Zhang, Zhuen Ruan, Yiming Wang

 The paper combines theoretical and experimental analysis to improve the accuracy of predicting paste yield stress by slump flow. It derives an analytical model of slump flow for yield stress, providing a theoretical basis for quantifying the rheological properties of paste with slump flow. The study uses three different tailings-prepared pastes and constructs an empirical yield stress model, showing high accuracy and good generality.

Aug 1, 2023

By Hussin A. M. Ahmed

Oxidized coals are difficult to float. Therefore, in this paper, a special flotation procedure was investigated for upgrading this type of coal. The procedure is called direct contact flotation. It relies on mixing dry coal either with pure (anhydrous) flotation reagent(s) or microemulsion. By applying the new direct contact flotation procedure, a coal yield reaching > 95% using anhydrous flotation reagents was achieved, but with relatively high consumption of reagents (up to 30 g/kg). This high reagent consumption may be attributed to the fines included in the flotation feed (100% less than 0.5 mm, with 40% less than 75 µm). On the other hand, the clean coal yield was found to be approximately 88% when mixing dry oxidized coal with microemulsion droplets from dodecane and dodecyl tetra (ethylene glycol) ether (C12E4) in water at a total reagent dosage of 10 g/kg. The direct contact of coal either with unhydrous reagents or microemulsion also provided a high flotation selectivity.

May 1, 2012

By Jim Buckley, Ryan Sibley, Scott G. Giltner, Thomas Pallua, Joe Schrank, Robert Cidlik

Because of variation in rock type and site conditions, it is important to create site-specific prediction models for peak particle velocity (PPV) and understand instrumentation mounting locations to better interpret the readings provided following blasting operations. The Atlanta Airport is expanding the section of underground tunnels for its Plane Train people mover, and drill and blast operations were determined to be the suitable method of excavation for the project. Extensive work was done to begin creating prediction models and determining levels of concern based on readings from various types of instrumentation. This paper analyzes the effect of close quarters construction blast vibrations and observed frequency spectrum on existing structures with data from 22 different seismographs mounted in various locations and ground conditions.

Dec 1, 2022

By Michel Dagbert

In the exploitation of porphyry-type deposits, the quality of the ore is mostly defined according to its grade. Besides the simplest distinction, ore-waste, several grade categories may exist and they correspond to the different ways in which the ore is further processed. At the time of mining the selection of the different categories is done from extensive information available from blast holes. But planning has to be done before this information is available and it is necessary for the geologist to forecast, from exploration and development data alone, the possible outcome of the selection done later on a block, a level, or the whole deposit and ultimately predict the ore reserves and value of the deposit. A good statement of this problem has been presented at the 1976 AIME annual meeting by Williamson and Hueller (1976). They have shown that, if the cut-off values are directly applied to the estimated grade of blocks, a gross overestimation of the recovered tonnage of ore (14%) will occur. This problem, now termed "the vanishing tons problem" (DaVid, 1977) seems to be common in many open-pit operations and it has been explained several times (DaVid, 1972; Huijbregts, 1975). In order to solve it l.Jilliamson and Mueller proposed a solution based on compiling masses and masses of blast hole data available from mined-out portions of the deposit. They derived empirical correction factors which provide for every block, given its estimated grade, the expected tonnage and average -grade of each category of material within that block. The purpose of our work is to repeat the same exercise but ignoring the blast holes data i.e. we want to derive the correction factors from the only DOH data. Doing this, we are more in the real conditions where the valuation of the mine and are reserve analysis has to be made before production actually starts. Two possible ways to achieve this goal will be investigated and the emphasis will be on recently

Jan 1, 1977

By T. W. Martin

The use of conveyors in large, open pit mines and their drawbacks are discussed. Technological developments such as long distance conveyors capable of handling large rocks are explored. The development and testing by the Bureau of Mines of a prototype crib and cable conveyor for handling large rocks are discussed, and possible modifications of the concept for a production model are examined.

Jan 1, 1984

By Giovanni Barla

The stress-relief method for the determination of the ground stress tensor is a common procedure in rock mechanics. In particular, the method of applying gauges to the end of a borehole is a well-established technique. Investigations, both experimental and theoretical, indicate that large discrepancies can exist in the determination of the ground stress tensor when the rock substance is not the ideal elastically isotropic material assumed for the reduction of data. The purpose of this paper is to extend the analysis of strain gauges applied to the end of a borehole to rock material more closely approximate to an orthotropic substance.

Jan 1, 1969

By Michael P. Connor, O&apos

The Wing Hill Garnet Deposit, located near Rangeley, Maine, forsed through assimilation of Early Paleozoic metasediments by an intrusive Devonian gabbro. The resulting ore body is exceptionally large and high-grade, consisting of 50-70% almandine garnet. Following open-pit quarrying, the ore is trucked to Industrial Garnet Extractives' mill in West Paris for final processing. Two grades of abrasive are produced - a pure, premium grade INDUSTRIAL GARNET and the Lower grade co-product IGE UTILITY GRIT, both of which are available in a variety of sizes. INDUSTRIAL GARNET is marketed world- wide into a diverse marketplace including both loose grain and bonded applications.

Jan 1, 1985

By Richard H. Johnson

White Pine Copper Company, a subsidiary of Copper Range Company located in Michigan's Upper Peninsula, mines a Precambrian sedimentary deposit containing finely disseminated chalcocite, native cop- per and native silver. Silver occurs predominately in certain strata and presently provides a mill head averaging 0.25 ounces per ton. This technical publication traces the development of silver recovery at White Fine beginning in early 1961. White Pine refined copper contains an excess of silver over and above that required to impart Lake Copper properties. The copper does not require electrolytic refining to meet industry purity requirements, nor is there sufficient silver to justify electrolysis.

Jan 1, 1970

By Diler Katircioglu-Bayel

The effects of the operating parameters of media filling ratio, solid mass fraction, grinding media size and grinding time on the stirred media milling of talc were studied. The findings were assessed based on the product particle size (d50, d10), surface area (Sw) and energy consumption (Em). Furthermore, after determining the optimum grinding conditions, Box-Behnken statistical design was used to determine the effect of parameter interactions on the d50 size. The media filling ratio significantly affects d50 size decrease compared with solid mass fraction and grinding time. The minimum d50 size was also achieved under optimum grinding conditions.

By Charles M. Pelanne

Without insulation we could not survive on this planet. This may sound like a self-serving statement but it is a fact. The blanket of air which surrounds us is a very effective insulating blanket, allowing some shortwave solar radiation to warm us during the day while retaining the longer infrared radiation at night. Our life on earth is very much dependent on materials performing an insulating function without being thought of as insulation, clothing, fur, window glass, the ice of an igloo etc. The mechanisms of heat transfer involved in these materials are analogous to those involved in engineered insulations - Engineered insulations are designed for maximum effectiveness for given conditions within the applicable retraints. Engineered insulations are very effective! As an illustration let us consider this graph (Figure 1). It represents: 1. The radiative heat transfer between two 1 foot2 (0.0932) radiantly black surfaces, one at 100F (38C) and the other at the temperature indicated on the bottom scale. This does not include the convective and conductive heat flow of the air, both of which are significant but small in comparison. 2. The heat transfer resulting from the placement of 1 inch (25.4 mm) of insulation [10 pcf (160 kg/m3) ceramic fiber] between these two plates.

Jan 1, 1976

By William J. Robinson

What is the cummulative rate of recovery of copper from a sulfide leach dump? This is one of the most frequently asked questions today. We, in the industry, ask it of each other when we meet; however, the technical answers may vary from "I don't know" to 'quite good" from people within the same company. Management also poses this question because it plays a vital role in our planning for future production. The answer is difficult because of the many variables between different operations such as physical construction of the dump, topography of the original site, characteristics of dump material, mineralization, water application, etc. Each has a bearing on the rate of recovery. OPERATIONAL DATA Our method of water distribution is unique in that each dump is drilled to allow physical injection of water into the dump. The in¬jection holes are drilled vertically, on 251 centers, from the surface of the dump. Normally, the holes are drilled 40' deep and cased with 4" PVC perforated pipe.. The pipe is perforated at one-foot intervals with four V diameter holes at 901 spacing on the pipe circumference. We formerly alternated shallow holes (20'-40') with deep holes (80'-l80') in an effort to cover the entire dump and hasten oxidation. The shallow hole depth varied according to the compaction thickness. The deep hole depth varied according to the height of the dump and the original ground profile, We prefer to have the deep holes end 20'-30' above the original ground level. This generally allows us to penetrate the coarse material at the bottom of the dump. We had to discontinue the deep holes_ in order to cover more dump area in a shorter period of time to meet increased production requirements.

Jan 1, 1972