Search Documents

By Immo H. Redeker

The Kings Mountain area of North Carolina is the lithium pegmatite center of the U.S., if not of the whole world. We have two spodumene and by-product mineral producing companies, Lithium Corp. of America, and Foote Mineral Company. We also have Kings Mountain Mica and Kings Mountain Silica Companies producing mica. feldspar, quartz and clay from weathered pegmatites in that area. Figure 1 gives the location of the spodumene pegmatite area in North Carolina. The two spodumene producers mine typical pegmatite ore in open pits after removing amphibolite or mica schist overburden which is sold to aggregate producers. The ore reserves are discussed elsewhere in this session. They are in the order of plus 50 million tons but not unlimited. 1.2 The major minerals found and concentrated from the North Carolina spodumene pegmatite ores are tabulated on Table 1.

Jan 1, 1977

By S. Mathur

Polyacrylic acid (P AA) was evaluated as a selective flocculant for dolomite-apatite system. P AA of 4 million MW was found to flocculate both dolomite and apatite. However, their flocculation behavior was significantly different with 450,000 MW PAA which was the lowest molecular weight fraction capable of flocculation. In single mineral tests, at a dosage of 2kg/t 90% of dolomite and 35% of apatite flocculated. Selectivity was achieved in mixed mineral tests where apatite of 90% grade at 70% recovery level was obtained in the concentrate from a feed consisting of 80:20 mixture of apatite and dolomite. The dolomite rejection was about 75% which corresponds to 1% MgO in the concentrate.

Jan 1, 1995

By Ronald L. Wiegel

In the 2000 page Handbook of Mineral Dressing by A. F. Taggart, the subject of material or metallurgical balances is covered in only six pages of eve-straining type. Although Taggart's work was compiled before 1945, and there has been significant progress since then in most areas of mineral processing, the practicing metallurgist's approach to metallurgical balances remains exactly the same as described in those six pages. There are several portions of Taggart's text appropriate to introduce the subject of this paper which I would like to quote: "Milling Calculations. Computations of per¬formance in milling are complicated by the fact that it is a continuous rather than a batch operation, that the quantities of solid materials handled are large and usually mixed with water, hence difficult or impos¬sible to weigh. Fortunately it is possible to determine many facts concerning perfor¬mance without knowing weights, if the value of various constituents is known in some common unit, e.g., the content of some par¬ticular metal or mineral, or of water, or some ingredient soluble therein, or of par¬ticles of a particular size or falling within some particular size range, or the like."

Jan 1, 1979

By Dolf W. Fieldman

Most recently the geologic setting of the mineral deposits in the Silver Cliff district is described by William M. Sharp in ?Geologic Map of the Silver Cliff and Rosita Volcanic Centers, Custer County, Colorado?, (U. S. G. S. Map I- 1081). The discussion will relate only to the southern half of the Silver Cliff volcanic center and differences in geologic interpretation, which are largely structural, will be pointed out as they arise. Only the manganese/silver zone of the Kate Area will be discussed in detail.

Jan 1, 1980

By BERND SCHÖNHERR, JÖRG DEHNERT, PETER WINDISCH, JENS STOPP

The Quick-Erect Stopping System (QESS) offers a new way of reducing the radon exposure of miners in Germany, especially during remediation work in old mines. The QESS is a lightweight, modular and reusable construction kit of interlocking telescopic aluminum tubes, radon-proof foil and expanding foam. It is designed to seal off radon-rich parts of galleries within minutes. Originally, the QESS was developed to protect miners against radon exposure. Then, the QESS found the attention of several mine rescue teams at a German mining conference. Some mine rescue drills by The Student Mine Rescue of the Technical University Bergakademie Freiberg, Wismut Mine Rescue and Front Range Mine Rescue helped to improve the system and highlighted its potential for mine rescue operations. Now, the QESS is well-suited for small-scale mining. The QESS can be used to both protect miners from radon exposure and to support mine rescue operations. Moreover, the QESS was also successfully used in ventilation experiments.

By C. Dale Elifrits

Observations made from laboratory analysis of samples of fine-grained argillaceous materials (shales) subjected to various changes in moisture content have been correlated to loss of strength in the rock material. This reaction to a change in in-situ conditions (subsequent to mining) at a mine site combined with the observed relationships of surface-disturbing subsidence features at locations where the predominant overburden material is fine-grained, provides a predictive tool for the subsidence engineer.

Jan 1, 1983

By H. Copur

Roadheaders have become widely used in underground mining and tunneling operations because they offer the flexibility to excavate soft- to medium-strength rock formations. A critical issue in successful roadheader application is the ability to develop accurate and reliable estimates of machine production capacity and the associated bit costs. Increased pressure to improve productivity and lower costs in the mining and civil construction industries has been the driving force behind the more wide- spread use of mechanical excavation systems. This has caused both industries to move away from the conventional drill and blast methods. Additional benefits of mechanical mining include improved safety, reduced ground support requirements and fewer personnel. These advantages, coupled with recent enhancements in machine performance and reliability, have resulted in mechanical miners taking a larger share of the rock excavation market. Roadheaders are the most widely used underground partial-face excavation machines for soft- to medium- strength rocks, particularly for sedimentary rocks. They are used for development and production in soft rock mining (main haulage drifts, roadways and crosscuts), particularly in coal, industrial minerals and evaporitic rocks. In civil construction, roadheaders are used to excavate railways, roadways, and sewer and diversion tunnels in soft ground conditions. They are also used to enlarge and rehabilitate underground structures. Their ability to excavate almost any profile opening also makes them attractive to those mining and civil construction projects where various opening sizes and profiles are needed. In addition to their high mobility and versatility roadheaders are generally low capital cost systems com- pared with most other mechanical excavators. Because of higher cutting-power density due to a smaller cutting drum, roadheaders can excavate rocks harder and more abrasive than continuous miners and borers.

Jan 1, 1998

By M. Moats, I. E. Paschalidou, K. Awuah-Offei

Tellurium (Te) is a rare metalloid that is predominantly produced from the treatment of anode slimes formed during copper (Cu) electrolytic refining. The US Government lists Te as one of the 50 critical minerals, partly, because of its use in thin-film photovoltaic (PV) technology. Given policy initiatives to increase Te production, it is important to evaluate the life-cycle environmental impacts of Te recovery as a by-product of Cu processing. The literature contains a few specific life cycle assessment (LCA) studies of groups of metals that include Te without proper regard to impacts per life-cycle stage of Te production or the effect of allocation on the results. This study builds an LCA model of the production system of Te from anode slimes treatment to evaluate the effect of allocation on life-cycle impacts. We build life cycle inventories using data from the Ecoinvent v3.7.1 database, literature, and engineering calculations and allocate impacts in proportion to products’ mass and economic value. The results show that economic value-based allocation yields greater impacts than mass-based allocation indicating the significant effect of the allocation approach on life-cycle impact estimates.

Feb 1, 2023

By MOHAMED WAEL, ANASTASIA GOEVA, ABDULAZIZ TAWFEEQI, IHTISHAM TARIQ, S. M. ZAKIR HOSSAIN, NIAZ ALI KHAN, MUHAMMAD FAISAL IRFAN

Carbon capture and storage (CCS) is an attractive area of research in such fields as CO2 mineral carbonation, global warming and sustainable energy systems. In this study, carbonation efficiency for aqueous mineral carbonation (MC) was achieved through two steps,which include leaching of calciumfrom cement kiln dust (CKD) followed by the reaction of pure CO2 with the calcium hydroxide precipitates formed by the hydroxylation using NaOH. Response surface methodology (RSM) with a Box-Behnken design (BBD) was applied to optimize the calciumleaching yield,while the carbonation efficiency from CKD was assessed using RSMwith central composite design (CCD). Optimization of calcium leaching is highly important, as it is a rate-limiting reaction step in MC and also influences and enhances carbonation efficiency. Different parameters including acid concentration (HNO3), leaching temperature, leaching time, and dose of CKD sample were considered in order to optimize the maximum yield of Ca leaching from the CKD sample. In addition, different CO2 flow rates and temperatures were used as parameters for optimizing carbonation efficiency. Two quadratic regression models were developed for each process, i.e. calciumleaching and carbonation. For calcium leaching, a maximum of 98.55% calcium was extracted under the optimal set of acid concentration 4.13 M, 90 °C, 28 min leaching time, and 13.8 g of CKD sample. For carbonation, the maximum carbonation efficiency of 89.2% was achieved for a CO2 flow rate of 1163 cm3/min at 90 °C. Calcium leaching results indicate that the leaching yield was significantly affected by all the input parameters except leaching time. For carbonation, both factors affected the carbonation efficiency, with the effect temperature shown to be greater than that of the CO2 flow rate. Additionally, the predicted results agreed well with the experimental values for both calcium leaching and carbonation processes, with errors of less than 1% and 5%, respectively.

Jun 5, 2020

By M. Fan, A. Hobert, W. van Dyk

Low flotation recovery and selectivity have been long-standing problems in the treatment of most ultra-fine phosphate ores. This paper investigates the improved flotation of two ultra-fine Brazilian phosphate ores from Itafos’ Arraias project. These ores are predominantly composed of quartz, muscovite, apatite and a Ca-Al phosphate. As a result of fine phosphate dissemination and associated grinding requirements, column flotation was selected for the metallurgical test program to address the inherent limitations of fine particle flotation using conventional flotation cells. Accordingly, both benchtop Denver cell and laboratory column flotation tests were conducted to optimize their respective flotation responses. Improved flotation performance was achieved using column flotation as compared to benchtop mechanical flotation. In column flotation, a P2O5 concentrate grade of 30.5-31.0% was yielded at a flotation recovery of 83.7-85.1% for the 38x0µm generated ultrafines. The benefits of Eriez’ column flotation technology realized from this study include a higher degree of selectivity, increased recovery, and reduced collector dosage as compared to bench-scale mechanical flotation.

Mar 2, 2022

By Wei Victor Liu, Na Zhang, Chengkai Fan, Bei Jiang

This study used artificial neural networks (ANNs) coupled with Gaussian mixture modeling (GMM) to analyze truck haulage data from openpit mines. The proposed weighted ensemble models performed better than benchmark models in predicting truck productivity, providing a new means of solving complex data and improving mine planning and decision-making.

Jun 1, 2023

By Harold J. Schock

This paper describes an experimental method for the monitoring of diesel-generated exhaust gas pollutants in a dead-ended drift for the purpose of assessing the effect of control approaches. Experiments were conducted to determine the relative merits of these ventilation configurations: no auxiliary ventilation, induction ventilation at the entrance to the drift, and ventilation of the dead-ended drift with positive displacement tubing. The drift used in this experimental work was approximately 105 ft. (32.0 mf long and slightly downsloping, with an average height and width of 8 ft. (2.4 m) and 28 ft. (8.5 m1 , respectively. The data were gathered for assessing these ventilation methods and for gathering data to support a computer model of the dispersion and mixing processes. For this drift, it was found that ventilation with positive displacement tubing provided the best removal of diesel-generated pollutants. Induction ventilation appeared to be the least effective of the three methods examined. A comparison was also made between personal monitoring and area monitoring. Results of this analysis showed that in regions of high concentration gradients, it was not possible to get good agreement between point sampling and personal monitoring. In well-mixed areas, good agreement between the two methods of monitoring was obtained.

Jan 1, 1980

By John Hanna

Recently. researchers at The University of Alabama have developed a two-step method for the treatment of phosphorus sludge that includes bulk removal of phosphorus by physical separation techniques followed by remediation of the residual P4 in the sludge using a novel wet air oxidation technique known as "HSAD", Tests made on samples of the electric furnace phosphorus sludge have demonstrated that essentially complete and fast removal of the P4 in the sludge can be achieved by the HSAD wet oxidation treatment, Further studies were made to determine the applicability of the two-step process on sludges of various origins. P4 contents different pre-treatment and storage conditions, The present work discusses the mechanisms and factors controlling the HSAD wet air oxidation remediation approach.

Jan 1, 1992

By M. Yekich, W. R. Reed, G. Ross, A. Salem

"Canopy air curtain (CAC) technology has been developed by the National Institute for Occupational Safety and Health (NIOSH) for use on continuous miners and subsequently roof bolting machines in underground coal mines to protect operators of these machines from overexposure to respirator coal mine dust. The next logical progression is to develop a CAC for shuttle cars to protect operators from the same overexposures. NIOSH awarded a contract to Marshall University and J.H. Fletcher to develop the shuttle car CAC. NIOSH conducted laboratory testing to determine the dust control efficiency of the shuttle car CAC. Testing was conducted on two different cab configurations: a center drive similar to that on a Joy 10SC32AA cab model and an end drive similar to that on a Joy 10SC32AB cab model. Three different ventilation velocities were tested—0.61, 2.0, 4.3 m/s (120, 400, and 850 fpm). The lowest, 0.61 m/s (120 fpm), represented the ventilation velocity encountered during loading by the continuous miner, while the 4.3 m/s (850 fpm) velocity represented ventilation velocity airflow over the shuttle car while tramming against ventilation airflow. Test results showed an average of the dust control efficiencies ranging from 74–83% for 0.61 m/s (120 fpm), 39–43% for 2.0 m/s (400 fpm), and 6–16% for 4.3 m/s (850 fpm). Minor modifications to the shuttle car CAC design and placement improved the dust control efficiency to 51–55% for 4.3 m/s (850 fpm) with minimal impact on dust control efficiencies for lower ventilation velocities. These laboratory tests demonstrate that the newly developed shuttle car CAC has the potential to successfully protect shuttle car operators from coal mine respirable dust overexposures. INTRODUCTION The development of the canopy air curtain (CAC) dates back to the 1970s starting with the initial development of the CAC by the Donaldson Company, Inc. under contract from the U.S. Bureau of Mines [Krisko 1975]. This CAC was originally developed for continuous miner operators when continuous mining machines had cabs. The need for a CAC on the continuous miner was eliminated when the cab was removed from the machine design. However, CAC development progressed to include CAC designs for a roof bolting machine to protect roof bolters from respirable coal mine dust [Goodman and Organiscak 2002, Listak and Beck 2012, Reed et al. 2017]. This roof bolting machine CAC research continues to the present day."

Jan 1, 2018

By T. Dunn

FMC Corporation has achieved a significant cost reduction through a new proprietary solution mining and processing technology at its Green River, Wyoming Soda Ash Facility. In the first phase, completed in October 1995, trona ore is dissolved, recovered and processed with the new technology, and then fed into an existing refining plant, replacing dry mined and calcined trona ore. The second phase, completed in April 1996, produced a fmal high purity product and increased capacity by 635,000 t/a (700,000 tpy). Both phases were completed under budget and well ahead of schedule.

Jan 1, 1998

By S. Torno

The elimination of ultrafine (<10 µm) clay particles is essential to the treatment of abandoned coal-washing plant tailings for the recovery of the remaining coal fraction by enhanced gravity processing. Effective hydrocyclone classification is required to remove this fraction. The highly variable composition and particle size distribution of such wastes creates significant difficulties in the operation of hydrocyclones for such classifications. Hydrocyclone laboratory investigations and their plant setup require lengthy or time-consuming tests. The use of empirical models of such classifications frequently requires modification to correspond to actual operating conditions. Results of the evaluation of computational fluid dynamics (CFD) modeling to predict hydrocyclone classification of coal-washing plant tailings are presented. Results of the standard k-epsilon turbulence, SSG turbulence and large eddy simulation CFD models are compared with the results obtained from analyzed hydrocyclone classifications. The CFD models tested are shown to be very effective in the simulation of hydrocyclone classifications for the determination of the classification particle size and adequate for determining the efficiency index values for many applications. The large eddy simulation model was identified as the most precise, but it is recommended that all three models be improved simulations of classifications above and below the classification particle size.

Jan 1, 2011

By S. S. Peng

In this paper, the precise definitions for a number of commonly used subsidence parameters are given. The subsidence parameters have been determined using an integrated approach for 110 subsidence cases collected in the major US coal fields. Attempts have been made to establish empirical formulae for the parameters. The results of this study indicate that some traditionally-held concepts should be changed.

Jan 1, 1995

By Matthew T. Mowry

As the mining industry continues to hire young professionals to supplant the growing number of retirees, a well-developed engineering curriculum, coupled with practical, real-world training, can prepare mining engineering graduates to make meaningful contributions in the industry. Successful companies can be measured not only by their reserve base and annual production but also by their retention of mining engineering graduates with zero to five years of operational experience. My personal experience in the industry during the last five years has been varied and rewarding. The knowledge and experience I have gained have taught me valuable lessons that prepared me for my current role.

Nov 1, 2013

By S. Tafazoli, D. Cooper, I. Bell, S. Nouranian, B. Sameti, M. Ramezani

"Image-based rock fragmentation sensing in mines and quarries includes an important rock boundary delineation step, commonly referred to as rock segmentation. This paper presents an artificial intelligence-based solution to this challenge. The proposed technique encodes prior knowledge of previously analyzed images into mathematical/statistical models. Human-labeled images are used as inputs to train neural networks through an optimization process. The networks can then be used in real time for rock delineation. To build the models, special deep artificial neural networks are used as a pixel classifier. The proposed classifier labels each pixel (edge, rock or fine) by analyzing a plurality of pixels within the image. Advances in machine learning allow the network to contain many parameters. The increased number of parameters is a strong factor in the classifier’s ability to correctly classify each pixel. Deep learning-based segmentation, combined with 3D imaging followed by post processing, provides a unified fragmentation sensing solution. Results from automatic segmentation are compared to human labeled segmentation using the percentage passing curves for 64 rock images. INTRODUCTION Mines and quarries can see significant productivity and performance benefits by controlling material sizes (McKee, Chitmobo, & Morrell, 1995; Sellers & Gumede, 2012). During the past decade, image-based fragmentation analysis has been applied to estimate rock size distributions in order to optimize procedures in mines and quarries. Using a roving camera and operator assisted analysis Maerz, Franklin, and Coursen (1987) measured the size distribution of the blasted rock and eliminated the need for manual sieve analysis. Since then, many others have introduced automated and manual methods for fragmentation analysis and improved upon existing approaches (Girdner, Kemeny, Srikant, & McGill, 1996; Smith & Kemeny, 1993; Palangio, Palangio, & Maerz, 2005; Tafazoli & Ziraknejad, 2009; Raina, 2013). In image-based fragmentation, rock boundaries are identified in the image, and an image scaling is applied to transform rock pixel sizes into real world dimensions. Usually geometric references, such as regularly shaped objects (discs and basketballs) (Siddigui, Ali Shah, & Behan, 2009), or the known size of an excavator bucket (Zeng, Chow, Baumann, & Tafazoli, 2012), are used to determine the proper scaling factor. In recent years, 3D imaging and sensing have also been incorporated to improve rock delineation. Specific methods include using camera-laser combinations and stereo imaging to measure rock fragmentation on conveyor belts (Noy, 2013; Thurley, 2013; Dislaire, Illing, Laurent, & Pirard, 2013) as well as portable fragmentation analysis devices with 3D imaging sensors (Sameti, et al., 2014)."

Jan 1, 2018

By H. H. Murray

Recently developed clay deposits that will impact regional and world markets are described. These deposits, their location, geology, and physical properties are delineated. Kaolins from the State of Para in Brazil and from Ukraine; bentonites from Argentina and India; and palygorskite and sepiolite from China are world class deposits that when processed using modem technology will produce excellent products. Other deposits that may affect regional markets are l<aolins from China, Australia and Indonesia; bentonites from Georgia (formerly USSR) and China; and palygorskite from India and Ukraine. New ball clay deposits that will affect regional markets are in China and Indonesia.

Jan 1, 1999