Search Documents

By V. Z. Sun

One of the major concerns of ground control in a coal mine is safety against failure of one of three components (i.e. roof, pillar, or floor) of the mine entry. In order to better design and evaluate stability of the mine entry with a certain confidence, a reliability approach is introduced rather than using the conventional safety factor (SF) method only. Advantages of using the reliability approach is that it not only takes variability of both rock/coal properties and stress distribution into consideration, but also assesses the stability of each component and mine entry as a whole system. Therefore, it is anticipated that, by using this approach, the current ground control technology in coal mine will convey a better sense of confidence. The results of a case example show a significant influence on the current design concept and stability evaluation of mine entry.

Jan 1, 1997

By Kunzo Amano

Fully-bonded rock bolts have been widely used in construction sites and mines in recent years. The purpose of this investigation is to prove the effectiveness of rock bolt supports in unstable ground through in-situ tests and numerical analysis. 2. MEASUREMENTS AND PROCEDURES OF IN-SITU TESTS The fully-bonded rock bolts as the mine road¬way supports were tested in the Fukasawa mine which is located in the northeast district of Japan (Fig. 1). The Fukasawa mine (one of the Kuroko mines) started the production in 1973, and the present monthly production is slightly less than 20,000 tons. The ore deposit which exsists at about 400 m depth is divided into several small lenticular shaped bodies. They are distributed apporiximately 1500 m in NW-SE direction and 700 m in NE-SW direction. The hanging wall is basaltic lava and the footwall is tuff. The rocks surrounding the ore bodies are soft but relatively intact, so the trackless mining system has been adopted from the beginning of the development.

Jan 1, 1982

By D. J. Lachel, Douglas E. Hansen, Bruce Kennedy

The very high cost of exploration and development for new mines requires that a carefully planned, complete, and technically competent geotechnical evaluation be applied to the ore body and the surrounding rock. The ground conditions must be predetermined sufficiently so that, during the development and exploitation stages, unexpected conditions will be of minor consequence. Ground conditions are a major factor affecting the cost of excavated items such as shafts and inclines. For example, shafts cost less to sink in tight dry ground than in highly pervious ground below the water table, with all other factors being equal. The proper mining methods also is dependent upon the ground conditions. Bad ground for room-and-pillar mining may be ideal for caving methods; whereas, ideal ground for room-and-pillar mining would be extremely difficult for a caving operation. To do a proper engineering design, the parameters of strength, deformability, and permeability must be determined, in addition to the loads that will be applied as a result of the mining activity. The required degree of accuracy for each parameter depends upon the individual case. For example, the strength of massive rock in which openings of small cross-sectional area are to be driven at shallow depths needs to be resolved only within several thousand kilopascals (pounds per square inch). Under such conditions, the rock strength is not likely to be of great economic importance unless the rock is very weak. Large openings at great depths require a much more accurate appraisal of rock strength and deformation characteristics. Ground water conditions are important at any depth. Today, a number of techniques exist for evaluating conditions before opening up the ground for development. These techniques and their applications are described in more detail later in this text. The evaluation of ore body ground conditions should start at an early stage, as soon as the deposit has been proven viable for a mine. Economic geology investigations mainly serve to define the value and limits of the ore deposit. To do this properly, the geology of the site is determined in at least as much detail as is necessary to define the "controls" for the ore body. The ground-condition evaluation must determine the engineering properties of the ore body and the surrounding material. This includes the structural geology as it relates to rock strength; i.e., the frequency, extent, and orientation of discontinuities such as faults, joints, bedding, etc. Ground water conditions also must be determined. It is important that the detailed geology of the site be determined at an early date. Reasonable geotechnical parameters must be established during this time period, so they can be used in mining model studies that include both physical and mathematical models. The ultimate goal bf-the geotechnical evaluation is to predict the ground behavior as the excavations are made and how the ground behavior will affect the safety and economic well-being of the mine. The formulation of a ground-condition evaluation program should be planned carefully to determine the particular geotechnical parameters only in as great a detail as will have a bearing on the mine design. For instance, it is not necessary to make numerous triaxial tests in strong rock when the mining will be conducted within a few meters (feet) of the surface in a regime of gravity loading and an absence of tectonic stresses. Similarly, it is not necessary to invest large amounts of time and effort in the determination of joint strengths if the orientations of the joints are such that the failure could not occur along them. Generally, the determination of ore body ground conditions can be divided into four main steps: 1) The general and structural geology of the site must be determined; this is determined primarily during the economic evaluation. 2) The material behavior characteristics of the deposit and the vicinity must be determined. 3) The ground water hydrology of the deposit and the vicinity must be determined. 4) Miscellaneous ground support considerations must be established. Gross features are defined first, followed by a series of increasingly detailed investigations. Specifically, the geology study should start by utilizing techniques such as remote sensing, topographic map interpretation, geologic mapping, etc. After the gross features, such as major faults, have been delineated, the studies are directed toward defining the more detailed elements of jointing, rock strength, ground water hydrology, and other characteristics. This information is used to formulate an assessment of the strength of the ore body and the surrounding rock. Finally, all of the gathered information is integrated to make an assessment of the rock behavior in relation to the types of openings, the excavation methods, the support requirements, etc., that should be used for the rock conditions that are present. The mine design and the geotechnical assessment should be an iterative process. General conclusions about the rock conditions will dictate a type of mine plan. The specific mine plan then should be modified by specific geotechnical considerations. For example, an initial assessment may conclude that the ore body is strong and that a strong rock unit is present over the ore body. Thus, one definite possibility is to mine the deposit by room-and-pillar methods. However, subsequent investigations may reveal faults through the deposit, requiring relocation of the mine openings so that pillars and other structures are in sound rock. In other words, the final mine plan should be compatible with the geotechnical aspects of the ore body.

Jan 1, 1982

By T. BoBo

"In the 1990’s metal prices were trending in a long term decline and the usual cost cutting exercises were adopted. Cuts to research and development made innovation difficult and the outlook was grim. But necessity is a strong motivator, and these conditions spurred the Mine-to-Mill movement which optimised across organisational “silos” and utilising new technology tools, innovative software and increased computing power. Many applications of Mine-to-Mill exploited the fact that comminution is usually the site processing bottleneck, and that blasting is more efficient at breaking rock than grinding. This approach sought to: • Understand and characterise rock breakage from mining to the mill • Develop models and simulators for blast design, fragmentation, crusher and mill circuits • Develop tools to measure in real time the particle size distribution of rocks on conveyors and Run of Mine (ROM) muckpiles • Ensure effective communication across the silos between geologists, blast design engineers, mining engineers and metallurgists These methods and the technology tools available in the 1990s were widely adopted at numerous sites around the world with significant benefits. SAG mill throughput increases of 10-20% were common. This was the advance the industry desperately needed. It was low capital cost; it was obvious. It was here to stay. Except, in too many cases, it didn’t. In the minerals price boom of the 2000’s Mine-to-Mill was no longer necessary to “survive”, even though it was still good business. Some operations, including some of the early success stories, slipped back to old habits of optimising within organisation silos instead of across them. Fortunately, other operators still embraced Mine-to-Mill and developed new techniques. Mine to Mill was still successful, but it not as widely adopted as we had expected it to be.Now the boom has ended and operations are again under cost pressure. Since these are the same circumstances that created Mine-to-Mill, it seems time to achieve the wider adoption. Since the 1990s many new or advanced technology tools are available for Mine-to-Mill projects: blast-hole sensors, new explosives formulations, new blasting techniques and modelling, ore tracking devices, improved image analysis to determine size, texture and colour of coarse ore, grade sensors, whole-stream simulation tools, even more powerful computing hardware and data analysis software. If we could achieve so much in the 1990’s, how much more can we achieve today when we have the same imperative, the same potential and a larger number of high technology tools?"

Jan 1, 2017

By D. M. Larsen

Since start-up in 1985, the Cannon Mine has produced and shipped a 170-g/ton (5 oz/ton) gold flotation concentrate to various smelters for gold and silver recovery. Several processes have been investigated to economically produce done' at the mine site from the refractory concentrate. This paper describes laboratory and pilot scale test work used in the process design and engineering. feasibility study of a 73-t/d (80 stpd) pressure oxidation and carbon-in-leach (CIL) facility. The designed pressure oxidation circuit utilizes a series of verti¬cal autoclave units operating at 170°C (338F) and 1.4 MPa (200 psig). Projected operating costs are discussed.

Jan 1, 1993

By Bobby G. Cahoon

The ( ) Tayaaja ( ) . The deposit ( ) 130 kilometers due east of the continental divide and approximately 290 kilometers east-southeast of Lima (Figure 1). Relief in the immediate vicinity of the mine, which lies or the west side of the Mantaro river, is in excess of 2,000 meters, and the elevation varies from a low of 2,000 meters above sea level on the Mantaro River to a high of 4,386 meters at point T-27 (Figure 2). Although the Cobriza deposit was first reported by the Italian Geographer Antonio Raimondi in 1866, only three reports have been published on the deposit, which began production in 1966 (Duefias, 1908; Fernandez Concha and Garcia y Garcia, 1961; Petersen. 1965). Many private reports have, however, been written by geologists employed by the Cerro de Pasco Corporation. These reports and the author's observations, while employed as the Cobriza Division Mine Geologists form the basis of the present paper, which describes the relations between-the ore controls in the Cobriza mine and the regional and local structure.

Jan 1, 1971

By J. R. Nawrot

Reclamation of potentially acid producing coal processing waste requires a 4-foot cover, and/or treatment to allow vegetation establishment. If not planned properly, soil covering alone does not prevent refuse acidification or formation of acid seeps. Adequate neutralization enhancement prior to soil covering can maintain an alkaline environment in the soil refuse interface and prevent acidification. Direct vegetation establishment using only limestone amendment (without soil cover) can successfully reclaim aged and weathered fine (Blurry) and coarse (gob) refuse if adequate neutralization treatment is provided for the oxidized surface zone. Acid seeps, representing an "after-the-fact" verification of an imbalance of acid-base equilibrium may also be corrected using upslope alkaline recharge techniques. Concentrated alkaline recharge pools have been constructed above previously soil covered acid gob at the Peabody Will Scarlet Mine to abate acid seeps. Preliminary monitoring results (1989-1992) from a concentrated alkaline recharge pool demonstration project in the Pit 4 area of the Will Scarlet Mine have documented a 50 to 80 percent reduction in acidity in the principal recharge pool groundwater zone. A 22% reduction in acidity has occurred in the primary seeps located downslope from the alkaline recharge pools. The initial improvements in water quality are seen as a positive indication that groundwater acidity will decrease further and amelioration of the acid seep will continue.

Jan 1, 1993

By Furuyama Takashi, Mori Sukeyuki, Hara Tsuyoshi, Fukushima Yujin

In mineral processing practice, flocculation is largely established as an engineering technique of waste water treatment and the study of parameters increasing the settling velocity of particles is still of great importance to improve the process. Further investigations were made using quartz (Q89) and fluorite samples (F91) which included 58.8% and 65.8% of -2.3 µm particles respectively. In all the experiments the flocculation phenomena were observed varying the pH value of the aqueous suspension. In contrast to quartz particles (Q89) which did not flocculate for all pH values, it was, noticed that fluorite particles (F91) flocculated in the alkaline range of pH over 11. With an aqueous suspension containing equal quantities of Q89 and F91, a hetero-flocculation of particles was observed at a range of pH below 10. In this case, the maximum floc size of the hetero-flocculation was 37.0-26.2 µm This size was about three times larger than when quartz (Q84) and fluorite particles (F85) were used with 32.4% and 40.4% of -2.31 µm particles respectively. Besides, in the experiments using Q89 and F91, the maximum size of hetero-flocculated single particles was found to be 6.54 µm instead of 3.27 µm as obtained with Q84 and F85.

Jan 1, 1995

By William Hodder, Ehsan Alavi, Nader Ghasempour, Daniel Cressman

The Don River & Central Waterfront Coxwell Sanitary Bypass Tunnel (CBT) Project in Toronto will extend approximately 10.5 km from Ashbridges Bay Treatment Plant west under Lake Shore Boulevard, north under Bayview Avenue and east through the Don River park area to the Coxwell Ravine Park. The tunnel is currently being mined by using a shielded dual-mode tunnel boring machine (open and close) capable of operating in EPB mode and lined by using a precast concrete segmental tunnel linear with an internal diameter of 6,300 mm and external diameter of 6,900 mm. The CBT is expected to be excavated mainly through shale bedrock of the Georgian Bay Formation, at approximately 50 meters deep. The tunnel crosses a buried bedrock valley in two locations, in the southern portion of the alignment, adjacent to the Don River, and at the northern portion of the alignment approaching the CX-1 shaft. In these two locations, the bedrock cover is expected to be less than 6 meters. The risk of encountering weathered bedrock, significant ground water inflows or surficial soil deposits through these buried valleys was identified during the design phase. The contract required the TBM to be designed with the ability to probe drill ahead of the TBM and convert to EPB mode if necessary, to cross this area. This paper will discuss the additional exploration that was performed by the contractor to identify the extent of this buried valley, the plan going into the zone of potential weathered shale, and the actual conditions encountered.

Jun 13, 2021

By W. H. W. Husband

Rock salt has been mined by the solution method for many years in many countries. Attempts have been made in the past in Canada and various other countries to produce potash by the' same method. However, only Kalium Chemicals Limited (1) has been successful, possibly because the conditions in Saskatchewan are the most favorable conditions to be found so far for the development of a solution mining method for potash. There are significant differences in solution mining of rock salt and solution mining of potash. First, rock salt deposits are relatively pure in respect to soluble minerals, whereas potash is never found in the pure state and contains Substantial amounts of other soluble minerals, particularly rock salt. In comparison to rock salt, much less potash is dissolved and brought to the surface for the same amount of water circulated through the orebody. The amount of water to be evaporated per unit weight of product is a major difference. Much greater amounts of water must be evaporated when producing potash and the treatment of the brine is more complicated because other dissolved salts have to be separated. Secondly, the rock salt deposits, particularly the domes, are much thicker. Bed thickness is of prime importance because it determines the yield of a well and consequently the economics of the process. Furthermore, as rock salt provides a strong roof structure, larger cavities can be developed and this prolongs the life of the rock salt well.

Jan 1, 1971

By D. Tahija

"Hecla's Greens Creek silver-gold-lead-zinc mill began using carbon dioxide rather than sulphuric acid to control pH in April, 2015. High pH levels in the grinding and lead flotation circuits are caused by the presence of re-mined cemented paste backfill in mill feed and need to be lowered to achieve good flotation response. Carbon dioxide has proven to be quite effective at controlling pH in the lead circuit with greatly improved pH target attainment. The allowable amount of carbon dioxide used is not limited by effects on lead-zinc selectivity and by poor froth characteristics, as was the case with sulphuric acid. Startup and implementation went smoothly, with few operational issues needing to be resolved. Early results from implementation of the system and its effects on mill performance will be presented. INTRODUCTION Hecla Greens Creek is a silver-gold-lead-zinc mine producing flotation lead and zinc concentrates, as well as a gravity gold concentrate. Besides their base metal contents, both the lead and zinc concentrates carry precious metals. The circuit is largely conventional, with SAG and ball mill grinding being followed by graphite removal preflotation, then conventional lead flotation and conventional zinc flotation. Both rougher concentrates are treated in regrind steps, followed by cleaner flotation. The cleaners tails are treated in an unorthodox bulk circuit to produce a low-grade zinc-lead concentrate marketed to Imperial Process smelters (1). BACKGROUND Backfill and Flotation pH The Greens Creek mine is an underground operation in which mined areas, after ore extraction, are backfilled, using rammed paste or pumped slurry. The backfill consists of mill tailings to which approximately five percent Portland or similar cement is added to enhance its compressive strength. Later mining near backfilled areas inevitably results in a considerable amount of old backfill being mixed with new ore before being shipped to the mill. Depending on orebody geometry, mining methods etc., the amount of backfill in mill feed is often 20% to 25% and sometimes even higher. Commercial cement, and consequently backfill prepared using it, contains excess lime. Because of this, backfill in mill feed is indistinguishable from the addition of a large amount of lime, so mill natural pHs often range above 10 or even 11. Similar situations have been recognized for many years at mines throughout the world (2)."

Jan 1, 2016

By C. D. Harrison, J. W. Parkinson

This paper compares the ash slagging potential of Illinois No. 6 seam coal as raw coal, as commercially cleaned coal processed in a baum-jig plant, and as coal cleaned to a reduced ash specification at the Electric Power Research Institute's (EPRI) Coal Cleaning Test Facility. The comparison is based on ASTM ash fusibility data, a slagging index, gravity fractionation analyses of critical mineral matter compounds, and comparative pilot combustion tests. The first three grounds of comparison are laboratory data. The final comparison involves burning about 13.6 t (15 st) of each coal at Conoco's 4.40-kW/h (1.5 million-Btu per hr) test combustor. The evidence of these four comparisons indicates that lowering the ash specification of coal before combustion can significantly improve the ash slagging characteristics of Illinois No. 6 seam coal.

Jan 1, 1987

By M. A. A. de Klaver

Functional Description Figure 1 is a typical flowsheet for a system for solid fuel addition to filter cake. Solid fuel, coal, coal breeze, or charcoal, is fed from a,stockpile to a surge hopper. The solid fuel is metered into a grinding mill. The fuel is dried and ground in a grinding mill. The on-size particles are removed from the mill by air sweeping. The ground solid fuel is separated from the air stream by a cyclone and stored in a surge hopper. The ground solid fuel is then pneumatically conveyed to a small hopper in the balling area. The fuel is proportioned into the filter cake just prior to mixing. An efficient mixer is very important to have a successful operation. The exact flowsheet would depend on a number of factors including what fuel is used, how the fuel is received, and the cnaracteristics of the fuel as received. Availability of floor space in the plant may also affect the flowsheet. For example, drying air may be supplied from the pellet furnace if the grinding mill can be located near the grate, or the pneumatic conveying system and a surge hopper may be eliminated by placing the grinding mill adjacent .to the mixing area. Also, for a multiple line plant, a ball mill rather than a roller mill may be more suitable.

Jan 1, 1980

By William Gleason

"Despite the difficult economic climate for the mining industry, more than 6,300 people joined SME for its 2016 Annual Conference & Expo in Phoenix, AZ, Feb. 21-24.Nearly every commodity has been bruised and battered during the past year, leading to one of the more difficult cycles for the industry in the past decade. Coal has taken some of the hardest hits and other commodities, such as copper and iron ore, have felt the sting of a slower growth in China and an oversupply on the market.The difficult conditions could not be ignored, but they did not deter SME from offering a forum for the industry to share knowledge, network with peers and learn about the best products and practices while visiting the sold-out exhibit hall (844 booths and 627 vendors) or while attending any of the 121 technical sessions that were offered.The current state of the industry was one of the overriding themes of the conference and during the challenging times there are often cutbacks as operations look to become leaner and more efficient, however, there is one area that cannot be cut – health and safety.The conference kicked off with a fascinating presentation from Colonel Mike Mullane, a former NASA astronaut who, in 1978, was selected as a Mission Specialist Astronaut in the first group of space shuttle astronauts. He completed three space missions and logged 356 hours in space aboard the shuttles Discovery and Atlantis before retiring from NASA and the U.S. Air Force in 1990.In his speech to a packed audience, he warned of the dangers of cutting corners to get the job done more quickly by guarding against the “normalization of deviance.”Normalization of deviance is a long-term phenomenon in which individuals or teams repeatedly accept a lower standard of performance until that lower standard becomes the norm. Usually, the acceptance of the lower standard occurs because the individual or team is under pressure (budget, schedule, etc.) and perceives it will be too difficult to adhere to the original higher standard. Their intention may be to revert back to the higher standard when this period of pressure passes. However, by getting away with the deviation from the higher standard, it is likely they will do the same thing when the same stressful circumstances arise again. Over time, the individual/team fails to see their actions as deviant."

Apr 1, 2016

By G. R. Luster

In most current practice, the methods that are employed in technical evaluations of cement raw materials are deterministic; i.e., decisions among alternative raw mixes and alternative plant designs are reached with the aid of only "average" compositions and "representative" samples of the available raw materials. Nevertheless, cement plants are sensitive to raw-material variability, and uniformly high-quality raw materials are not so abundant as they once were. Some simple examples will illustrate how geological techniques can be combined with geostatistical and operations-research approaches to customize mining and processing systems to deal with variable raw-material compositions.

Jan 1, 1987

The dissolution kinetics of gold in iodide solutions with oxygen in an autoclave was investigated. The leaching process was described by a gas-liquid-solid heterogeneous reaction. The effect of stirring speed, temperature, partial pressure of oxygen, and concentration of lixiviants on the overall leaching rate was investigated. It was found that the dissolution of gold was limited by a heterogeneous chemical reaction. The apparent activation energy was measured to be 34.7-54.3 kJ/mol under the conditions studied. Experimental findings were in good agreement with the kinetic model proposed.

Jan 1, 1996

By Peter Zhang, Daniel Su, Mark Van Dyke, Heather Dougherty

The integrity of shale gas wells in longwall chain pillars under the influence of longwall mining is a safety concern for both coal and gas operators. Previous modeling studies of gas wells in longwall pillars have shown that a FLAC3D model can predict longwall-induced stresses and deformations in gas well casings with reasonable accuracy. The predicted casing deformations can be verified by multi-finger caliper survey. This study concerns the influence of longwall mining on eight shale gas wells in a shale gas well pad located in the chain pillars between two adjacent longwall panels under 1,030 feet of cover. FLAC3D modeling was performed to predict longwall-induced deformations in gas well casings based on site-specific mining and geological conditions. Small deformations less than 0.5 in were predicted in the intermediate casing above 600 ft depth, and very small casing deformations less than 0.15 in were predicted below 600 ft due to high abutment pressure and high frictional resistance along the weak bedding interfaces. After the first panel was mined, a 56-arm caliper survey was performed on one of the wells to measure the longwall-induced casing deformations in the intermediate casing. The predicted casing deformations were then compared with the measured deformations, which indicated that the prediction was generally in good agreement with the measurement in terms of deformation locations and magnitudes. Findings from this study provide valuable information not only for stability assessment of shale gas wells in longwall chain pillars but also for developing engineering guidelines to preserve casing integrity through adequate pillar and casing design.

By M. Ishaq, J. Rosami, J. Brune, E. Sidrow, C. Tsai, S. Slouka

Respirable rock dust poses serious long-term health effects to workers in mining and tunneling underground hard rock environments. When inhaled, respirable silica particles commonly found in quartz and other minerals will scar sensitive lung tissue and cause irreversible lung diseases. Characteristics such as concentration, type of mineral, particle size, and particle shape inhaled can harm workers to various extents. Therefore, this study characterizes rock dust particles less than 100µm in aerodynamic diameter that are released from cutting hard rock in the underground mining environment. In this study, laboratory full scale cutting tests on samples of potash rock were performed with radial picks to generate dust. Three stages of pick wear were tested: new, moderately worn, and severely worn. Comparisons between different stages of pick wear to dust concentration, size distribution, and particle shape characteristics are drawn from this study to start determining the scenarios when the released airborne dusts become potentially most hazardous for workers. Although further testing needs to be conducted to make viable conclusions, the moderately worn pick, or the pick with the most blunt tip, in these experiments are potentially the most dangerous. The blunt pick tip released the highest concentration of dust and generated particle shapes with the highest aspect ratio compared to the other two picks. The preliminary results of this study allow for the further development of optimum bit management and maintenance systems to control the exposure of respirable dust to mine workers.

Mar 2, 2022

By Brian Fulcher, Matthew Bartlett, Jarrett E. Carlson

This paper discusses the challenges to complete the construction of two large underground Metro stations and connecting tunnels in the Tren Urbano system. The completion work includes the installation of specialized mechanical and electrical systems, extensive architectural finishing as well as coordination with systemwide power and controls installed by others. A unique feature of this project was the simultaneous design and construction of the structural/civil/architectural/mechanical/electrical works by KKZ separately from the power and control systems under the management of the Owner, its consultants and other contractors. Completion of this project comes after almost six years of continuous design and construction in a dense urban environment. The project was confronted by many challenges that could only be met with the combined efforts of the Joint Venture team in close cooperation with the Owner and its System wide Contractor. This paper will also address many of the major design and construction changes implemented to suit the Owner’s requirements.

Jan 1, 2003

By W. J. Wuest

The U.S. Bureau of Mines (USBM) has recently developed a rock mass classification system for evaluating the structural competency of bedded roof strata; the Coal Mine Roof Rating, or CMRR. When compiled with the companion Lotus 1-2-3 spreadsheet, which is simple to learn and use, CMRR data are a useful tool with applications to longwall gate road pillar design, safety hazard mapping, and artificial roof support analysis. This paper demonstrates these applications under actual conditions found in current U.S. mining operations.

Jan 1, 1995