Search Documents

By R. Thorpe, M. Dosbaba, A. Kopriva, A. Niiranen, J. Ruokanen

"Automated Mineralogy (AM) is an important diagnostic tool in flotation plants as it adds ore and particle mineralogical properties to traditional mass and chemical data. AM is used in project development, for future ore studies and for diagnosing concentrator operations. With the exception of operations who own central laboratory or on-site systems, the use of AM is often limited to the analysis of a comparatively small set of samples. Metrix Plant Technologies has partnered with TESCAN to integrate TIMA AM technology into the implementation of Performance Assessment Campaigns (PAC). Routine daily composite samples from the mill are analysed mineralogically on a size-by-size basis over several weeks. All the relevant metallurgical, process control and mineralogical data is combined into a single large database for mass balancing and interactive examination. This paper describes the implementation and results of a PAC at the Agnico Eagle Kittilä gold mine in Finland. Although challenging, the addition of mineralogical data as dependent variables in multivariate analysis leads to a much deeper understanding of the root cause effect of events driving the flotation performance. INTRODUCTION TO STUDY The Kittilä mine, owned by Agnico Eagle, is Europe’s largest primary gold mine, with annual production of approximately 180,000 Oz. The operation is located in Lapland in northern Finland, and is currently expected to operate until 2035. The location of the operation is shown in Figure 1. Historically, the mine was an open pit, although in recent years ore is sourced solely from underground operations. The processing plant features crushing and grinding, followed by carbon flotation and sulphide flotation. Carbon concentrate is a waste stream, and sulphide concentrate reports to pressure oxidation (autoclave) and CIL circuits for gold extraction. The final flowsheet is shown in Figure 2. Following commissioning in late 2008, the operation achieved commercial production on May 1st 2009. Gold recovery in flotation gradually increased to a 92-96% range at a throughput of ~3500-4000 tonnes per day. In late 2014, the operation commissioned a plant expansion to ~5000 tonnes per day. Following a commissioning period, the operation stabilised with recoveries in a 90-94% range, which over any given period was determined to be ~2% lower with statistical significance. The trends from start-up of gold recovery in flotation and throughput are shown as follows in Figure 3. In early 2016, Agnico Eagle Kittilä mine, along with Agnico Eagle Technical Services (AETS) partnered with Metrix Plant Technologies and TESCAN, to perform a Performance Assessment Campaign (PAC) at Kittilä, involving automated mineralogy on five key streams at Kittilä on 40 days selected from a 50 day period between February 15th and April 4th 2016, when plant operations were stable. In addition to the mineralogical data, metallurgical and operational data were pooled into a single, powerful database to explore opportunities for the operation to improve recovery in a sustained manner, ideally to the levels pre-expansion."

Jan 1, 2017

By Dirk van Zyl

Pad construction costs can impact the overall economics of heap leach projects. Pad construction costs for single-and double-lined pads, using various designs, are listed for a typical small and large project. Double-lined pads are now more often required by regulatory agencies. Unless such designs reduce the risk of site specific contamination significantly, the extra costs cannot be justified from an economical viewpoint. Specific attention is given to the short project life (typically five years) of heap leach projects. A few numerical examples are presented to demonstrate the overall economic impacts of these costs on economic parameters.

Jan 1, 1990

By W. J. González

With the increasing demand for minerals and the decline in the quality of ore reserves, technologies to maximize recovery are critical to a mine?s economic success. Many mining waters exhibit the potential to form hardness-based inorganic scales, which inhibit effective mineral recovery. Often, a continuously-fed chemical deposit control program is implemented by the mine site to inhibit these scales. The use of retractable scale coupons is the current industry standard for monitoring these programs; however, a key drawback to their use is the limited, and sometimes untimely amount of information they provide. A proprietary fouling analyzer has been developed that can be used to continuously monitor the formation of inorganic scales in mining process streams. Consequently, it can be used to continually, and more effectively, communicate the efficacy of an antiscalant program, thereby providing the ability to compare different scale control programs and to optimize their feedrates. Case studies presented validate the applicability of this technology to help optimize mineral recovery.

Feb 23, 2014

By Ruari Soutar-Dawson, Fisher Wang, Alan Boylston, Michael Denzel

Vertical stirred mills are increasingly used for fine grinding applications in the mineral processing industry due to their high energy efficiency. Thus, modeling power draw is of great interest proven by the effort in previous work including analytical models. In this contribution the development of a DEM-CFD coupled model is presented to determine power draw under different operating conditions. These include grinding media filling level, shaft speed and fluidization as well as changes in grinding compartment configuration. An extensive test program on an especially equipped test mill is initiated to validate the model.

Feb 22, 2026

By R. K. Mensah-Biney, M. T. Hepworth, K. J. Reid

The loading characteristics of gold-bromide species onto activated carbon were evaluated using a batch system. The overall loading of gold onto activated carbon was rapid for the first few hours, but it continued without cessation as a result of the reduction of gold. Therefore, conventional equilibrium considerations were not applicable. Although loading continued slowly after several days, an abnormally high, loading capacity value of 10-12 meq/g carbon (650-800 kg Au/t) could be attained in 72 hours. The loading of gold-bromo species by activated carbon was by the mass transfer of (AuBr4)- species to the external surface to be reduced to metallic gold by carbon. Elution of gold from loaded carbon was feasible provided the carbon had not been loaded to high capacity values. If loading is carried to high levels, complete elution becomes impractical, and the gold may be recovered by ashing the carbon. For the high loading capacities observed, this option would appear to be cost effective. The effect of several variables on the loading capacity of the activated carbon for gold-bromo species is discussed.

Jan 1, 1994

By T. M. Barczak, S. C. Tadolini

Reduction in the recovery time required and improvements in safety during a longwall face move have compelled coal mine operators to examine and use pre-driven longwall recovery rooms. The recovery entry is developed at the longwall stop position and supported ahead of time so that the required combinations of standing and internal sup-ports can be installed before the longwall face approaches. A calibrated three-dimensional finite element model, developed in conjunction with an underground test area, provided the critical components and design principals for a comprehensive parametric study. The study indicates that vertical, horizontal, and shear stresses concentrated on the outby abutment pillar corner of the recovery room resulting in deformations in the immediate roof above the primary roof support anchorage level. The results of the numerical model and field site observations indicated that the combination of the internal bolting system and the standing concrete supports are critical for the successful and safe extraction of the longwall equipment. Cable supports installed at and angle over the pillars can help stabilize the disturbed zone above the adjacent fender and outby pillars, however; standing supports are required in most sedimentary roof conditions to increase stability and assure a safe longwall extraction.

Jan 1, 2004

By T. Gupta, T. Ghosh

"In recent years, the demand for Rare Earth Elements (REE) have grown rapidly due to increasing demand and global supply shortage. The supply deficit of these critical elements has encouraged the search for new sources of REEs, possibly Coal and Coal byproducts. Coals from certain parts of the world can be rich in REEs, and can approach a total concentration of 1000 ppm. Two Alaskan coal samples were investigated for the effect of size and density on the concentration of REEs on three selected size fractions. Flotation tests were conducted for finer fractions. Additionally Bottom ash and Fly Ash samples from a power plant have been examined for REE concentration. The results show that the upgrade potential for REEs on ash basis from whole coal basis ranges from 2:1 to 4:1 for Wishbone Hill and Healy coal samples respectively. Flotation of the finer fraction for both coal samples, conducted under similar conditions, reveal higher concentration of REE’s in the tailings. Both coal samples have a comparatively higher LREE content than HREE. Trends of REE content of the power plant products on ash basis revealed that Fly Ash has a slightly higher concentration of both LREE and HREE than Bottom Ash. Keywords: Rare Earth Elements, Coal, Coal Ash INTRODUCTION Rare Earth Elements (REEs) and their compounds are vital components in industrial, automotive, petrochemical, defense and medical applications. Dysprosium in combination with other elements is used in laser materials and nuclear control applications. Neodymium is present in magnets that are used in green power generation such as the manufacture of wind turbines and also in hybrid cars. Europium, Terbium and Yttrium are used for devices that have visual displays such as computer screens and laptops [1, 2]. REEs pose fewer environmental problems of disposal and recycling than conventional heavy metal counterparts [1]. Rare-earth metals are key ingredients for radar systems, avionics, modern national defense and satellites [2-8]. In the last 25 years China has been mining, processing and refining Rare Earth elements at affordable prices thus gaining a virtual monopoly in the market. The many fold rise of the prices of REE elements over the last few years and frequent disruptions in supply has forced various nations to invest in indigenous extraction of REEs by increasing production from previously productive sites and to expand the production from new alternate sources including coal and coal byproducts [9]. Coal and Coal beds have been found to be significantly enriched with certain critical metals and can be a potential source for both Light Rare Earth Elements (LREE) and Heavy Rare Earth Elements (HREE) [10]. Moreover, coals with high REE concentrations have been discovered in Pavlovka and Rakovka coal deposits in Russia, Appalachian deposits in USA, Sichuan Basin deposits in China and others across the globe [10-13]. A recent study from China looked at how different trace elements (including numerous REEs) partition in various size fractions of Antaibao coal from China. The finding indicates that the REEs, phosphorous, and thorium all have their high concentrations in the particle sizes 0.5 to 3 mm, and 6 to 25 mm. REEs are also often present in the form of phosphates such as monazite in coal [13, 14]. The objective of the study is to identify the concentration of REEs in Alaskan coals and to investigate the effect of density and size in the distribution of REEs in coal and coal byproducts."

Jan 1, 2016

By F. E. Senftle

Preliminary geophysical surveys for nickel deposits are usually carried out by airborne magnetometer and surface electrical methods. Once an anomaly is discovered by these techniques, one must resort to chemistry to identify nickel and determine its concentration. Consequently, a method to determine nickel quickly and quantitatively at the exploration site could help guide detailed sampling and provide analytical data that might otherwise be delayed at distant laboratories. In addition, borehole probes capable of indicating nickel in the rock adjacent to the hole, should prove attractive to the exploration geologist. With these needs in mind, preliminary investigations have been made to demonstrate an in situ analytical technique which appears feasible for nickel exploration. The method depends on the very high energy gamma rays emitted when nickel absorbs a thermal or low energy neutron. These neutron capture gamma rays should be distinguished from the lower energy gamma rays emitted during decay of radioactive nuclides as in conventional activation analysis.

Jan 1, 1971

By . A. Drouin, J. -M. Lalancette, D. Lemieux, C. Chouinard

"A gold bearing pyrite concentrate was treated at the demonstration scale (15 t/d) for the extraction of gold using a cyanide-free process. The pyrite was depressed in the flotation circuit in order to promote the flotation of copper and to achieve a sufficient copper grade to meet the copper smelter criteria. However, the recoveries of copper were 80% and only about 50% for the gold was found in the copper concentrate. The balance of the gold (50%) and copper (20%) contained in the pyrite concentrate as a reject from an overall flotation circuit. The gold grade in the pyrite concentrate is 5.40 g Au/t and copper about 0.77%. About 170 tons of pyrite concentrate were processed in the DST demonstration plant. The concentrate was first oxidized using a fluid bed to produce a calcine. Copper was then extracted as copper sulphate using diluted sulphuric acid. The residual solid was submitted to the DST chlorination process for gold extraction. Thereafter, the gold was recovered from the pregnant brine by precipitation over silica using DST proprietary process. The maximum gold recovery by chlorination was 90%. The average gold recovery by cyanidation of these calcines was 71%. INTRODUCTION Dundee Sustainable Technologies (“DST”) has developed a chlorination process as an alternative to the conventional cyanidation process for the extraction of precious metals from ores or concentrates. The technology offers viable and efficient gold recoveries and the ability to handle refractory ores and contaminated material (As, Hg, etc..). The process was successfully demonstrated on hundreds of samples provided by various mines, exploration and development projects and has evolved from laboratory experiment to demonstration at an industrial scale. DST’s chlorination process operates in a closed loop circuit, which implies that no liquid effluents are generated. The chemistry and process design allows precious metal deposits containing base metals to be treated viably. The tailings from the process are inert and non-toxic, sulphide depleted and thus non-acid generating. The efficiency of the process has demonstrated excellent gold recoveries within a fraction of the time needed for cyanidation to obtain similar results. The company completed in 2015 the construction of the first industrial demonstration plant operating with the DST technology. The plant has a capacity of 15 tons per day of mineral concentrate, and the ability to extract gold and silver utilizing DST chlorination technology. DST has tested its chlorination technology at demonstration scale on the refractory pyrite concentrate containing 5.40 g Au/t and 0.8 %copper. This auriferous pyrite concentrate, was by-product of copper concentrate respecting the copper smelter norms, is produced in a country where cyanide is prohibited and refractory to cyanidation. The pyrite concentrate was initially processed successfully (gold recoveries: > 90%) by the DST technology at laboratory (2011: 20 kg) and pilot (2014: 5 tons) scales to extract gold. About 170 tons of this pyrite concentrate were processed in the DST demonstration plant located in Thetford Mines."

Jan 1, 2017

By T. McCallum, C. Cooper, B. Hutzler

"In copper solvent extraction, managing the quality of the organic phase is a key parameter to ensure optimal physical and metallurgical performance in the plant. Increased throughput as a result of declining ore grades coupled with advances in plant design and practice, resulting in reduced organic losses, has pushed the limits of the status quo with respect to organic quality. Clay treatment of plant and recovered organic at the optimal dosage is critical in maintaining quality, however, achieving the optimal dosage through existing filtration capacity and practice can be difficult. Cytec has developed a process aid that increases efficiency of existing filtration equipment that has been successfully implemented at two commercial SX operations. ACORGA® CB1000 enables higher dosages of clay while allowing for more efficient use of existing filtration capacity. This study analyzes results from commercial trials and demonstrates that improved organic quality and clarity is achievable through optimization of current treatment practices. INTRODUCTION Decreasing ore grades have prompted copper solvent extraction operations to raise PLS flow rates, increasing plant throughput to maintain production1. The ability to process higher flow rates through existing mixer-settlers historically came at the expense of increased entrainments2. However, advances in mixer-settler design, practices and improvements in organic recovery processes have enabled operations to maintain, and in some cases reduce organic losses while achieving higher flow rates through existing equipment. Based on the increased demand on the SX equipment and reduced losses (or more efficient recovery) maintenance of the circuit organic quality through efficient clay treatment is now more important than ever. This paper discusses common industry practices and related issues in organic clay treatment, and presents benefits achieved in commercial operations through the use of ACORGA® CB1000 Clay Binder. IMPROVEMENTS IN DESIGN AND PLANT PRACTICE Mixer-settler design has improved since the first commercial copper SX operation in the late 1960s. Advanced designs in mixer, settler, and settler internals have contributed to reductions in entrainments. For example, improved impeller designs have been reported to decrease organic in aqueous entrainment from the ‘old designs’ of 50-200 ppm3 to as low as 4 – 10 ppm confirmed via diluent and reagent consumptions . Similarly, operations are reporting a 20-50% decrease in reagent consumption when compared to the original design criteria3. Operations have optimized settler internals to increase coalescence and have improved settler operating practices which have been shown to reduce entrainments7. Comparison of the SX world operating data from 1999 and 2007 shows reductions in organic entrainment losses with increases in flow rates."

Jan 1, 2015

By Knezicek Zeljko, Knezicek Tihomir

Lignite open cast mine "Dubrave" is the largest lignite mine in Bosnia and Herzegovina. The open cast mine was designed with two external waste dumps. Waste dump "West" is the major dump, while "Cajici" dump is used for dumping waste taken from leveling the terrain. The major waste dump contains 14.6 million cu.m. of waste, while the side waste dump contains 3 million cu.m. of waste. Existing situation with available sites for depositing the waste shows that additional space for dumping the waste must be provided. Three options can be taken into consideration. The fact is that none of the three options are suitable for the current production situation. This article deals with the optimization process for obtaining the optimal variant where a waste dump can be located and selection of the most valuable option.

Jan 1, 2002

By T. S. Golosinski

This paper identifies the components of belt conveyor shifting force as a vertical force. Pv, horizontal force, Ph, and longitudinal force, P1. A method for estimation of these forces is proposed, which relates their value to the properties of the conveyor structure and rails, shifting operation parameters, and other site-specific conditions. The effect of this force on shifter behaviour is analysed and guidelines are developed for selection of a suitable shifter. Also discussed are the requirements of the shifting operation for other equipment.

Jan 1, 1986

By Mostafa Benzaazoua, Bruno Bussière, Mukendi Kongolo

The desulphurization process has been proposed over the last few years for acid mine drainage control at certain mines, which generate low to medium grade sulphidic tailings (-3 to +25 wt% S). The environmental sulphur recovery, which means the sulphur to be floated to produce a non-acid generating final tailings, depends mainly on the intrinsic neutralizing potential of the tailings. However, in some cases the sulphur cleaning is complicated by other parameters which affect the flotation probability of the sulphide particles. In this study, a number of tests were conducted with a Hallimond tube and Denver Cell on both pure mineral and mine tailings. To develop a better understanding of the mechanisms of non-selective sulphide flotation, three types of approach were investigated in this work: (i) pure pyrite at progressive milling degrees, (ii) artificial mix of pyrite and quartz at different calibrated granulometry and (iii) same composition tailings with 26 % wt sulphur at progressive milling degrees. The effect of the granulometry on the sulphide flotation was demonstrated both. The results allow us to define a granulometry model, which can then be considered in the whole desulphurization modeling.

Jan 1, 2000

By Blair K. Salisbury

Dissolution within Permian evaporites of the Delaware basin has created extreme lateral geologic and physical property inhomogeneity within and above the evaporites. Discriminating a sulfur deposit's geophysical signature from other variances is difficult. This is particularly true of porosity-dependent gravity and electrical methods. However, other techniques that detect alteration of strata above sulfur deposits may be applicable individually or in combination with other types of data. Relationships between sulfur deposits and gravity, magnetic, gamma radiation, spontaneous potential, and soil geochemical measurements are illustrated by data from several Delaware basin geophysical and geochemical surveys.

Jan 1, 1992

By Thomas Konstantis, Spyridon Konstantis, Panagiotis Spyridis

"Tunneling and Underground works are unequivocally subject to a diversity of inherent uncertainties associated with the geotechnical, hydro-geological and environmental regime that surrounds them. On many occasions, these uncertainties can provoke loss events of considerable consequences. The present contribution elaborates on losses that the insurance market has suffered in the recent years, following a construction failure event. These losses are being considered and analysed on a quantitative basis through evaluation of cost related data, with explicit discretization of the applied construction methodology and of the subsequent developed failure type since both of which are considered of major importance. Given the identified persistence and regularity of some loss-contributing factors, recommendations are provided on the basis of a proactive risk engineering management approach that are envisaged to reinforce the understanding of project risks and alleviate the incurred insurance cost. 1 INTRODUCTION The underground construction sector has always been a very challenging area for all involved parties, including the insurance market. Main reason for that remains the uniqueness of the uncertainties sources and the subsequent inherent risks that the tunneling and underground projects are exposed to. In many instances, these risks materialize, leading to loss events with substantially high impact on reinstatement cost and incurred delays, which depending among others on the insurance coverage will have to be bared by the Insurance market. In the recent decades and as the tunneling industry boomed and expanded with many major and significant projects undertaken around the world, the insurance market was faced with additional challenges. Increased competition during tender coupled with the scale and complexity of the projects and politically driven decision making exerted pressure on the project timelines, completion dates and budget. The pressure for on-time or even early project completion- to avoid liquidated damages or achieve bonus payments, respectively- along with cost reduction efforts and the incentive for innovative failure events. That, in turn, put additional pressure on the Insurance market which had experienced a significant amount of losses with substantial cost. One of the triggered mitigation actions was the introduction of the Code of Practice for Risk Management of Tunnel Works (ITIG, 2006 & 2012; MunichRe 2006, Wannick, 2007, Spencer, 2008, Adeyemo, 2011)."

Jan 1, 2016

By R. R. Klimpel

The industrial processing of ores containing precious metals such as gold is generally very mining site specific, e. g. McQuiston and Shoemaker (1985), vanZyl et. a1. (1988), Fuerstenau and Hendrix (1990), and Hausen et. a1. (1990). The variety of various mineral processing techniques employed is extensive and includes size reduction, size classification, gravity separation, roasting, cyanidation, chemical and/or bacterial leaching, ion exchange and/or solvent extraction, and froth flotation. Gold occurs in the earth's crust on the average in very low concentration estimated by various sources to be between two and five parts per billion. For a specific ore deposit to be considered as an economic source of gold, generally a concentration of near one part-per million (one gram / Mton) or more is required. From a mineralogical viewpoint, gold often occurs in its native or free form. However, it can also occur as gold compounds of telluride, antimony, and selenium contained within either sulfide minerals such as pyrite, arsenopyrite. and pyrrhotite or, to a less extent, within silicate, oxide, and carbonate minerals. In many locations, alloying of gold with silver is found. The optimal processing method for recovering gold is determined by many factors such as the mineralogy of the gold bearing minerals as well as the associated mineralogy of the gangue minerals, the type of liberation profile of the gold bearing minerals upon' size reduction, and the particle size of the gold itself. Free or native gold particles can vary in size from the extreme of large nuggets to very finely disseminated gold associated in a complex sulfide mineral matrix. Typically free gold particles of several hundred microns or larger are efficiently recovered by one or more of a number of gravity based techniques due to the large specific gravity differential of gold (19.3 to 15) versus typical gangue minerals (5 to 2.7). When gold is associated with a sulfide (usually pyrite) matrix, historically most industrial plants involving size reduction and subsequent liberation have operated in a size range of 50 to 80 percent less than 75 microns. Grinding finer than this has been normally not economical unless the ore has a high gold content in the feed ore.

Jan 1, 1998

By M. D. Johnson

The San Andres mine, located in the western mountain region of Honduras, Central America, contains epithermal gold mineralization as disseminations, in quartz-chalcedonic veins and stockworks. Host rocks include a thick sequence of Cretaceous to Tertiary conglomerates, sandstones, rhyodacite tuffs and andesites. Mineralization is controlled by northwest and northeast striking, normal faults and fractures which dip steeply east and west. Currently, 500 STPD of 1. 93 Grams/MT gold ore is being open-pit mined from the conglomerate and andesite. The mine is at the west end of a mineralized zone that can be traced over an area of approximately 1.5 square kilometers.

Jan 1, 1993

By Sathit Tandanand

Geological differences among various coalfields restrain the applicability of subsidence prediction using existing European methods. To modify these methods for domestic conditions, the Bureau of Mines, U.S. Department of the Interior, developed a method of assessment to evaluate the lithological effects on subsidence in the Northern Appalachian basin by examining data collected from 16 longwall panels in the coalfield. The assessment is partially completed, and the results to date show that the ratio of maximum subsidence to the extraction thickness, known as the subsidence factor, can be expressed in terms of the width-to-depth ratio by a simple exponential equation which has a coefficient tentatively considered as the subsidence index. This index varies with the lithology of a particular site and can be expressed in terms of the percent distribution of weak and strong rocks in the overburden.

Jan 1, 1982

By Enrique Levy

Central America is graduating this year into large scale mining with the start up of Inco's multi-million dollar nickel laterite processing plant in Guatemala. In the other extreme of the Isthmus in Panama Texas Gulf Sulphur is doing check diamond drilling and foundation test drilling at the Cerro Colorado copper porphyry. The higher price of gold and silver has spurred development and exploration of several small precious metal mines. The purpose of this presentation is to make a brief resumé of the most important mines operating in the area and a list of significant exploration projects. Also, tables will be shown to compare mining codes and taxes. Unfortunately these tables lack information on Panama. Before starting I like to express my appreciation to Kennecott Copper who permitted the use of some of the data compiled by the author on their behalf during the year 1975. Other persons which did not want to be named also have my gratitude.

Jan 1, 1977

By Yuting Xue, Khaled Mohamed

Rib control is a critical component of underground coal mining operations, and comprehensive rib support design is essential for ensuring the safety of miners. However, there is currently no standardized approach for rib support design in the United States. To tackle this issue, the National Institute for Occupational Safety and Health (NIOSH) has developed a standalone application, Design of Rib Support (DORS), for rib stability assessment and rib support design under development load. The rib support design in DORS starts with the rib support density, which is determined from the unsupported rib factor of safety (RibFOS). The relationship between rib support density and unsupported RibFOS was obtained from the collected field data. The objective of this research is to validate DORS rib support design by analyzing the extent to which the proposed design capability was utilized to support the coal ribs using numerical simulations. A series of numerical models with varying overburden depth and rib height were built and the ribs were supported with the DORS-recommended rib support design. The bolt load was analyzed under different conditions and the results show that bolt load varies with the overburden depth, the location of the bolt and bolt length. The load in the bolt(s) increases with the reduction in unsupported RibFOS. The bolt(s) start to yield when the unsupported RibFOS falls below a threshold value of 0.8 and secondary support is necessary.

Jun 25, 2024