Search Documents

By Gilbert A. Bonforte, Hugh P. Caspe, Tracy K. Lundin

The Narragansett Bay Commission (NBC) Combined Sewer Overflow Abatement Program is a major effort to address and mitigate discharges from combined sewer overflows in the Providence, Rhode Island area. The proposed system consists of three deep rock tunnel segments totaling 17.8 km (11.1 miles) in length that will provide 860,000 cu m (227 million gal) of storage at depths up to 99m (325 ft). This paper discusses 13.5 km (8.4 miles) of 6.64m (21.8 ft) finished diameter tunnel, four construction shafts, 19 dropshafts and one large diameter pump station shaft tapered from 1 5.2m (50 ft) at the surface to 27.4m (90 ft) at depth. All facilities are in preliminary design.

Jan 1, 1995

By C. D. Elifrits

The required reclamation of land disturbed by surface coal mining often results in the creation of some over steepened slopes which are prone to rapid erosion and sediment production. This natural activity on such slopes is not desirable nor allowed under current regulations. Experience has indicated that novel approaches must be devised to address the problem. Research conducted on field sites in Missouri has indicated that construction, during the reclamation and grading processes, of a man-made drainage system will control the erosion. The drainage system must replicate or exceed the natural system in terms of drainage density and channel frequency. Basic design considerations will be summarized in this paper and field results shown.

Jan 1, 1986

By J. G. Groppo, A. E. Bland, B. K. Parekh, W. F. Stotts

Many coal preparation plants discard fine coal (generally minus 100 mesh) because it is difficult to beneficiate economically. At the Kentucky Energy Cabinet Laboratory (KECL), the waste streams from several Kentucky preparation plants were evaluated for cleaning with counter-current column flotation. A series of performance evaluations were conducted using a 0.05 m (2 in.) internal diameter (I.D.) 7.9 m (26 ft.) high laboratory column. The objectives of these tests were to assess the performance in terms of recovery and percent ash in clean coal and to optimize the operating parameters relative to combustible recovery and grade. Refuse streams containing 30-50 percent ash were upgraded to 2-8 percent ash with Btu recoveries of nearly 90 percent. A pilot scale column flotation cell was installed at the Bell County Coal preparation plant. This pilot plant utilized a 5.79 m (19 ft.) high and 0.15 m (6 in.) I.D. column to verify the performance data of the 0.05 m (2 in.) I.D. column for two different waste streams. Performance evaluation and pilot plant testing results related to scale-up are discussed.

Jan 1, 1988

By M. Misra, I. A. H. Schneider

The flocculation of -38 pm calcite, hematite and kaolinite aqueous suspensions by the yeast Candida parapsilosis and products derived from rupture of the microorganism was studied. Flocculation of hematite suspensions by the microorganism and its derivatives readily takes place between pH 2.8 and 11.4. Maximum flocculation occurs at about pH 6.5. Flocculation of calcite suspensions by the microorganism and its derivatives readily takes place between pH 7.0 and 11.8. Maximum flocculation occurs at about pH 10.0. Flocculation of kaolinite suspensions was less than that for the other two minerals. However, a soluble fraction derived from the rupture of the organism functioned as a good flocculant for the mineral, albeit at an increased concentration, between pH 2.6 and 11.5. Maximum flocculation occurs between pH 6.8 and 7.2. An attempt is made to relate the behavior of the various systems to the surface characteristics of the minerals and the surface and chemical properties of microorganism and its derivatives. Experimentation used to evaluate the flocculation includes actual flocculation tests, microelectrophoresis measurements and scanning electron microscopy.

Jan 1, 1994

By W. M. Schafer

The risk that water quality will be degraded by mining activity can be evaluated using risk analysis techniques. Water quality impacts can occur where water-rock interactions with tailings, waste rock, or leached ore lead to increased loading of constituents into surface or groundwater. Constituent loads contributed by mining facilities are determined by the migration route and chemical evolution of mine water. Mass load contributions from mines can be determined by estimating the prototype pore water in contact with mining waste, predicting the rate and timing of flow, assessing the degree of geochemical attenuation, and modeling chemical mixing with natural surface or groundwater. Mining facility siting and design measures can alter the chemical evolution of mine water by varying the quantity or quality of flow. Stochastic risk management techniques provide a powerful tool for quantitatively identifying the environmental consequences of various siting and design alternatives.

Jan 1, 1998

By M. C. Fuerstenau

A number of interesting and. important phenomena were revealed during a study of the response of beryl to sulfonate flotation (1). Perhaps the most important observation is the effect of various cations on flotation response. Experiments showed that in the vicinity of pH = 3. 0, about three ppm Fe.+++ increased recovery of leached beryl from about 60 to 100 per cent, whereas about four ppm Ca++ reduced the recovery from 60 to 2 per cent. With the exception of ferric iron, all of the other cations investigated reduced flotation recoveries drastically at this pH. As postulated in the paper "Sulfonate Flotation of Beryl", (1) even with low concentrations of polyvalent cations and sulfonate (on the order of one ppm), cation¬ sulfonates are precipitated immediately in solution. That is, blueish-white clouds .were noted to form after given additions of salts to. known solutions of sulfonate. Furthermore, it was also shown that one-hundred-fold more ferric iron than necessary to form the precipitated cloud had to be added to effect complete flotation. In other words, some form of solid ferric sulfonate was found to function as the collector in these systems. The form of the compound was suggested to be Fe (RSC3)2OH and that bonding to the surface occurs through the hydrogen of the hydroxyl. As the form of this compound was shown to be dependent on the extent of hydrolysis of ferric iron, it is to be expected that ferric iron will be unique in some pH region. Further, if the presence of hydroxyl in the neutral precipitated compound is of primary importance, then other cations should function similarly but at different values of pH, since they will hydrolyze at different concentrations of hydroxyl ion. To determine whether the premise of hydrolysis is correct, the study was extended to quartz systems lit the presence of various cations at various values of pH.

Jan 1, 1964

By K. E. Burgher

Since World War II, the need for the use of explosives in construction, mining, and quarrying near congested urban areas has increased dramatically. Often times a coal mine, once isolated from a city, finds itself surrounded by residential and commercial structures. The United States Bureau of Mines and others have researched blast design to a point where ground vibration and airblast damage can be avoided. A problem still exists, however. It is the fact that people often react to only the loud noise associated with a blast although it may not cause damage. Most often it is the concussion of a blast, less than 20 hertz and inaudible, that produces damage. Public fear from the "startle" and "fright" of loud blast noise greater than 20 hertz leads to the complaints which are generally unfounded. See Thackray, Touchstone, and Baily (1975) for a further discussion of the startle effects of loud sudden noises. When blasts are designed in accordance with U.S.B.M. specifications, management generally has little to worry about with respect to damage claims. Complaints, however, still arise when the noise is accentuated from the blast. It is meteorological conditions which dictate how the sound levels will propagate. Some mines use small pilot test shots (generally one-two lbs) to determine when atmospheric conditions favor sound travel.

Jan 1, 1987

By S. Chander

The effect of sample storage in argon and in air on kinetics of oxidation of pyrite from a coal source was studied using accelerated weathering test in laboratory columns. Prior to the weathering tests the samples were crushed, ground, and stored for various time periods in argon and air. The results showed a dramatic difference in the rate of oxidation of the aged samples. The differences were interpreted based on the hypothesis that the aging of pyrite led to the formation of surface coatings which changed with time. The significance of these results in pyrite/reagent interactions in flotation and in evaluating the acid mine drainage potential of pyritic waste materials is discussed.

Jan 1, 1993

By R. Xiong, A. K. Fallaw, G. Wang, L. R. Moore, S. Dobson, J. Gu

"INTRODUCTION The Central District of the Florida phosphate industry is located in southwest Polk and southeast Hillsborough Counties, with the Southern Extension lying in western Hardee, eastern Manatee and northwest De Soto Counties. (Lawver, 1983) Figure 1 shows the major phosphate formations in Florida. Almost all Florida phosphate production has been in the Central district with additional production from a mine in the Northern District. The Central District is comprised of the Bone Valley Deposit, a relatively thin layer of high grade ore which has been the main source of phosphate mining for decades, and the Hawthorn formation, a thick but low grade formation which covers most of peninsular Florida. (Lawver, 1983) Florida phosphate producers use the Crago process where calcium phosphate is floated with anionic, fatty acid type collectors followed by cationic reverse flotation of silica with amine type collectors. The phosphate matrix is put through various size separation techniques to obtain a typical -28 Mesh (< 700 µm) particle size for fine flotation and a -16 mesh (< 1190 µm) to +28 mesh (> 700 µm) particle size for coarse flotation. In some cases this coarse fraction can be sent to shipping as an intermediate product. The +16 mesh (>1190 µm) to – ¾“ (19 mm) fraction is sent to shipping as a final product called pebble. Figure 2 demonstrates a simplified diagram of the mining and processing of calcium phosphate (matrix) through a Central Florida mine. Particle size and mineralogy are important considerations in the Crago process for two main reasons, the mass of the particle and the particle surface area. Both of which are dependent on the coordination of the anionic collector to available Ca2+ sites on the minerals’ surface. The increased surface area, and available Ca2+, of the smaller apatite particles will allow for more fatty acid molecules to coordinate than the larger particles, with a lower availability of Ca2+. So, the larger particle would require more collector to be introduced in the system to sufficiently cover the apatite particles to produce a surface sufficiently hydrophobic to attach to air bubbles allowing flotation to occur. (Guan, 2009) The Bone Valley deposit has very favorable flotation characteristics when compared to other mining ores around the world. The matrix of the Bone Valley is relatively high grade, BPL (Bone Phosphate in Lime) values typically range from 6-18%, BPL recoveries, from such a matrix, can often be achieved above 85+% with fatty acid based collectors dosed below 1 #/ton. As mentioned, the sizing is an important step as there is also high grade apatite in the +16 mesh (1mm) that is screened to a final product grade, 60-65% BPL. The lack of quartz in the larger size fraction has allowed the Central District to produce high quality, low cost phosphate product, called pebble, through effective screening with no further beneficiation. (Guan, 2009)"

Jan 1, 2015

By L. H. Munson, E. H. Carbaugh, D. E. Hadlock, L. F. Munson, R. L. Gilchrist

As a result of the Three Mile Accident and because of evidence indicating radiation protection problems, the U.S Nuclear Regulatory Commission (USNRC) undertook a major effort, with the assistance of the Pacific Northwest Laboratory (PNL), to analyze radiation protection programs at 47 commercially operated nuclear power plants. This effort, the health physics appraisal program (HPAP), using a modified management oversite and risk tree analytical logic methodology (MORT) which consisted of analytical trees with applicable questions for each tree, was subsequently extended to include USNRC licensed uranium mills. In the uranium mill appraisal, a team of four senior radiation safety professionals spent a week at each mill evaluating the total health physics program. Prior to the HPAP, the USNRC inspection efforts were designed to determine if the licensees were fulfilling the requirements of the code of federal regulations and the mills source material license. The HPAP, however, was designed and structured to facilitate an integrated look at the total program. It is also directed into areas for which explicit NRC regulatory requirements may not currently exist. The latitude of the HPAP was designed to allow professional judgement in the evaluation of program adequacy, because merely meeting the explicit regulatory requirements does not necessarily ensure an adequate and effective health physics program. The results of the first eight site visits and the generic health physics problems identified within the uranium milling industry will be identified in this paper.

Jan 1, 1981

By T. Emery, D. Sweet, J. Bourgeois, B. Seymour, D. Porter

Cemented rockfill (CRF) is being used to backfill primary and secondary stopes at the Eagle Mine, an underground nickel and copper mine operated by Lundin Mining. National Institute for Occupational Safety and Health (NIOSH) researchers from the Spokane Mining Research Division (SMRD) are conducting cooperative research with the mine staff to determine if the size of a CRF sample affects its measured strength properties. Based on previous research by NIOSH, cylindrical samples of CRF ranging in size from six to eighteen inches in diameter were cast at the mine and cured underground. The samples were later transported to the SMRD laboratory and the Michigan Technological University where tests were conducted to determine the strength and elastic properties of the CRF. To further analyze the relationship between backfill density and compressive strength, different ASTM International compaction techniques were used to cast the samples. For comparison, tests were also conducted on in-situ core samples that were drilled from a stope which had been backfilled with the same CRF mix. The data collected from this study not only improves our understanding of CRF in-situ properties but also helps optimize Quality Assurance/Quality Control (QA/QC) methods for backfill preparation and testing.

Feb 1, 2023

By J. Loredo

Asturias, in Northwestern Spain, has an extensive mining history. As a result of these historical mine activities where operations have been usually developed with little control on effluents or emissions (environmental regulation of mining activity has only been introduced recently), pollution has been severe in some areas, specially in Hg abandoned mine sites, which constitute one of the major environmental problems related to mining. In many of these sites, materials stocked in spoil heaps can be considered as hazardous wastes because of their chemistry, content on ecotoxic elements and potentiality to spread these to the environment. In the humid climatological conditions of the region, water and wind eroded spoils are dispersed through the environment by different pathways and occasionally surrounding soils and waters are intensively affected by pollution. According to the environmental risks that these unreclaimed mine sites suppose for human beings and ecosystems, remedial options must be considered.

Jan 1, 2003

By W. Z. Choi

In our previous work, a population balance model describing the simultaneous processes of size reduction and mineral liberation has been developed. The experimental verification of this model, however, has been limited to a binary mineral system containing only one composite particle class. When considering multiple classes of composite particles, the estimation of model parameters becomes much more difficult. In the present work, a procedure for estimating model parameters for a multiple composite class model has been developed. Emphasis is placed on the direct experimental determination of these parameters. The physical significance of the breakage rate function and the liberation function in characterizing the liberation process is also discussed.

Jan 1, 1987

By Stuart Ratcliffe, Denis Kidby

The development of Vitrokele™ Technology over the last 10 years is reviewed with reference to mine site piloting and com­mercial applications. The first mine site piloting was conducted in Australia in 1989 followed by a further six continuous site trials in Australia, Canada and the USA. These major pilot plant studies are complemented by over 50 laboratory scale batch and pilot testwork programmes. The first commercial plant using Vitrokele™ Technology was the Connemara project commissioned in Zimbabwe in 1995. Subsequent to this, three commercial scale projects have been designed using Vitrokele™ to recover precious metals, base met­als and cyanide. The various projects are discussed with relation to the differ­ing flowsheets applied to each particular case.

Jan 1, 1998

By S. Vivek

An atomic force microscope (AFM) was used to measure the surface forces between silica plate and glass sphere in sodium oleate solutions. Hydrophobic forces were observed when the two surfaces were activated by CaOH+ or MgOH+ ions. The force measurements conducted in the absence of the surfactant showed that the activated silica surfaces do not exhibit the primary hydration forces that have been observed between unactivated surfaces. The activation mechanism was studied by calculating the contributions from electrostatic and chemical interactions to the total free energy change. The results suggest that the adsorption of the hydroxo-complexes is controlled mainly by the lateral interactions between the adsorbed species on the silica surface.

Jan 1, 1999

By J. P. Ramsey

This is a description of the efforts of a research project intended to demonstrate methods of alleviating pollution from coal mine refuse piles and slurry lagoons. These are mainly derelict barren sites. Some are burning and some are vulnerable to wind erosion which causes air pollution. Some occupy valuable land near metropolitan areas. They are an integral part of the landscape of the Appalachian and Midwestern Coal Fields. They are important in the light of growing civic awareness of the great general problem of waste disposal and environmental improvement. In the V-shaped valleys of the Pocahontas Region, they continue to be piled higher and higher. In flatter topography, they tend to form broad, flat ridges. Some contain more metal forms than others and some have a minimum of metal, but weather to a fine talc, which chokes streams with a fine particle suspension. Most are burning or have burned, but burning or weathering, most all are sources of pollution to the atmosphere and to adjacent waterways. This demonstration project is being carried out at an abandoned mine near the town of Du Quoin in southern Illinois. It is jointly sponsored by the Truax-Traer Division of Consolidation Coal Company and by the Federal Water Pollution Control Administration of the Department of the Interior. The site area is a refuse pile and slurry lagoon, each of fifty acres. It is hoped that basic data from this study will be generally applicable to other sites and will provide a basis for rational and efficient engineering design of future reclamation projects. Most refuse piles have extremely long term capabilities to produce highly potent acidogenic oxidation products typifying the more serious aspects of acid mine drainage contamination. Numerous sites remain where the abandoned mine no longer discharges acid waters, but its associated refuse pile continues to generate significant quantities of acid and other oxidation products even after many years.

Jan 1, 1969

By M. G. Rylatt

The Ekati process plant flowsheet features the common steps in diamond recovery plant design. Primary treatment and concentration is by crushing, scrubbing, high-pressure grinding rolls and heavy medium separation (Fig. 1). Secondary concentration is by an attrition mill; wet, high-intensity magnetic separation and X-ray sorting (Fig. 2). All of these are performed on site, although final sorting of the diamonds into commercial categories will be carried out elsewhere. The initial throughput rate is 9 kt/d (9,900 stpd), increasing to 18 kt/d (20,000 stpd) during the first 10 years of operation. A range of ore characteristics will be encountered that will effect the plant operating conditions during the life of the mine. The adopted design envelope is based on these expected variations. The design is based on the use of large-scale equipment, incorporating the latest and most efficient technology available. Where proven technology exists, no attempt was made to reinvent the wheel. However, where recently developed technology offers a significant advantage, this has been incorporated into the design. The Ekati run-of-mine (ROM) and coarse ore handling facilities are unheated, to take advantage of the better handling characteristics of the frozen ore in winter. The stockpile reclaim features an MMD mineral sizer (a toothed roll crusher) to minimize the problems of handling thawed, sticky kimberlite in the summer and break frozen lumps in the winter. All processing downstream from primary crushing and the coarse ore stockpile is carried out in a temperature-controlled environment in the main process plant building. Personnel involvement in the process is mini¬mized by using a Modicon Quantum series PLC with human-machine-interfaces (HMI) running Wonder-ware software on dedicated personal computers.

Jan 1, 1999

By Paul A. Rittenhouse

Its a pleasure to be with you this afternoon and to talk briefly on one of my favorite subjects -- the U.S. sulphur industry. As our Chairman mentioned, I have been associated with the sulphur industry either directly or indirectly for the last twenty years, both on the production side and as a consumer. Sulphur, while unseen and relatively unknown to most people, is like margarine ... that ubiquitous spread ... that is yellow and nearly omnipresent in the industrial world. It is because sulphur, in some form, is required in nearly all aspects of our economy that makes its study so interesting to me as a researcher. An analysis of the sulphur outlook requires examination of such industries as fertilizer, paints and pigments, copper and zinc, uranium, petroleum, chemicals, pulp and paper and textiles - just to name a few. Of course, because its use is so widespread and ever-changing it is difficult to develop and maintain a good understanding of the sulphur industry. It is also a problem to cover the industry in a short discussion and to project its really dynamic nature. Hut, if you will bear with me, I will attempt the task. First of all, let me say that sulphur today is a world commodity and to a large extent moves freely in world trade; nearly a third of the world&apos;s sulphur or something over 15 million tons in 1974 entered international trade. However, today our interest is in the current changing sulphur picture in the U.S., with particular emphasis on the western part of the country.

Jan 1, 1975

By P. Guliov

In the first part of this paper the authors present an overview of industrial minerals produced in the Canadian provinces of British Columbia, Alberta and Saskatchewan, and supplied to the Pacific Rim countries. The second part outlines some of the unique opportunities for industrial minerals that exist in the three western Canadian provinces and those minerals we feel have development potential for overseas markets. Because of time constraints, it is not an exhaustive presentation on industrial minerals, but is focused on a few selected minerals that we believe have high potential.

Jan 1, 1990

By D. G. Kotlyar

Oxidized sulfide minerals, commonly formed by weathering, increasingly are becoming important resources as primary sulfide deposits are depleted. Oxidation, in general, reduces selectivity and recovery in flotation. The objective of this research was to determine the mechanisms of oxidation and collector adsorption in sulfide systems as a step towards developing improved technologies for beneficiation of oxidized sulfides. Data from microcell flotation tests are combined with electrochemical and spectrophotometric measurements. The adsorption of ethyl xanthate (EX) on oxidized sulfides was characterized using AC impedance techniques and correlated to flotation response. The floatability of chalcocite, chalcopyrite and pyrite was dependent on the extent of oxidation. Oxidation for 1?) d at 65? C inhibited flotation of chalcocite, and chalcopyrite even after the addition of a large amount (1 x 10&apos;) M) of collector. Heavily oxidized (27 d) chalcocite remained unfloatable. However, longer oxidation of pyrite and chalcopyrite restored the floatability. Oxidation resulted in an electrically resistive, nonporous surface layer.

Jan 1, 1993