Search Documents

By J. Kuti

In room and pillar mining a large number of working points are arranged to follow a mining pattern. Geological and roof control problems can be overcome or their effect minimized by varying this pattern. Longwall mining on the other hand, fixes the mining pattern for anyone panel. This aspect of longwall mining leads to constancy, so that a well-conceived organization, ventilation, dust and roof control systems lead to daily repetition and subsequent simplicity of control. All the same, a fixed mining pattern calls for a very careful consideration and selection of design parameters. (Ref. 1.)

Jan 1, 1971

By Frederick B. Brien

For many years tin mining in Bolivia has been very important to the economy of the country. In recent years the tin content of the ore reserves has been steadily declining. An improvement in concentration efficiency is highly desirable in order to increase productivity from the present-low-grade mine ores and to allow retreatment of the many millions of tons of tailings from past operations, some of which equal the present ores in tin content. A number of investigators have been or at present are working on various phases or approaches to the problem. Gravity concentration is used in Bolivia today as it has been in the past to recover tin minerals from the mine ores. An objective of the work reported in this paper was to examine the possibility of treating present low-grade ores and sink-float tailings products, at a relatively coarse grind, in order to produce a higher grade feed material to the present gravity concentration plants. The possibility of using heavy liquids in cyclones to treat large tonnages with a minimum of outlay presented itself and is of particular interest since appropriate heavy liquids are available and with physical properties which lend themselves to simple recovery methods. Tests were carried out using a closed circuit laboratory cyclone assembly. It was desirable to determine the value of using the SG50 concept and Tromp curves for analyzing the cyclone concentration test results. The effects of entrained water on the behavior of ore particles in the cyclone were examined.

Jan 1, 1964

By R. V. Ramani

Demands on available lands will continue to increase due to the projected increase in population and industrial expansion. Though there is an upper limit on the available lands, the multi-use nature of the lands will make it possible to meet these demands. However, this will not happen without adequate planning. Land uses can be broadly categorized as non-renewable and renewable. Lands with mineable resources can be dedicated at some point in time to the extraction of resources. Such a dedication, however long-term, is only temporary because of the non-renewable nature of the mineable resources. Implied here is that the land will be available before and after mining for other uses. Planning for such lands must have the objective that, as far as practicable, no non-renewable uses are pre-empted and no renewable uses are permanently destroyed. The primary aspects of this planning process will be addressed in this paper, These aspects include a discussion of planning responsibility, data needs and availability, the integration of mine planning and post-mining land use planning and a long-term plan for resource conservation and utilization. Minerals, together with agriculture and forestry products, are the primary sources of wealth. Therefore, to avoid land development that may pre-empt future mineral resource utilization, the local planning groups must be aware of the mineralization and mining potential. Much work needs to be done to identify and characterize the mineral resources. Even more work is needed in land use planning for lands with mineral deposits.

Jan 1, 1982

By Verya Nasri, Jaeseoung Lee, Ashish Bhargava, Shashank Gupta

This paper presents the unique design and construction challenges for the Technoparc Station, located in downtown Montreal as a part of Réseau Express Métropolitain (REM), a light rail rapid transit system. The station is located 15 m below the street with rock-bearing secant pile wall as the primary structural system working as both the retaining and gravity structure. The paper highlights the challenges related to the support of excavation structure, invert slab resisting high hydrostatic forces, waterproofing tightness etc. It also focuses on the importance of Building Information Modeling (BIM) in underground tunneling projects for effective coordination, clash-free, optimized design and costs.

Jun 13, 2021

By Ronald M. Hays

The White Pine Copper Division of Copper Range Company is a large copper producer operating an underground mine, mill, and smelter on Michigan's Upper Peninsula. Principal water discharges are from the tailings basin where these discharges are high in dissolved solids because of mine water pumped into the basin. Principal air emissions are from the smelter where SO2 emissions are uncontrolled. Although water discharges and air emissions have not had significant environmental impacts, environmental regulations could require additional control procedures. Because of low copper prices and poor profitability, cost of compliance with possible new environmental regulations could have serious impact on White Pine with no apparent significant beneficial environmental impacts.

Jan 1, 1979

By Alistair James, James Alcorn, Chaitan S. Sandhu, Andy Small

The Risk-Informed Decision Making (RIDM) working group is a group of industry professionals formed under the joint initiative undertaken by United States Society of Dams (USSD), Tailings Dam Safety Committee and Canadian Dam Associations (CDA) Mining Dam Safety Committee (MDC). The working group was organized to develop a guideline on implementation of a RIDM process relating to the design of mining water dams and Tailings Storage Facilities (TSF). Since its formation in 2022, the group has completed a literature review of more than one hundred (100) cross industry publications on applications of RIDM in mining water dams and TSFs, has held two industry workshops in Niagara Falls, Ontario in 2024 and Saskatoon, Saskatchewan in 2025 to capture industry input relating to the understanding and application of RIDM. The working group has subsequently formulated a process that constitutes good industry practice as it relates to application of RIDM in mining dams and TSFs. The authors, through their engagement and leadership in the working group and facilitating the two industry workshops in 2024 and 2025, are of the opinion that the successful application process of RIDM across Canada and United States (U.S.) is still not clear to many industry practitioners. There is confusion over terminology, good versus poor RIDM, and in some cases reluctance to use the RIDM terminology. This paper addresses critical knowledge gaps identified in the RIDM implementation for mining water dams and TSFs through three years of stakeholder engagement. It provides clarity of the process via a joint position statement and implementation roadmap, resolves terminology confusion, and documents contradicting industry opinions to promote adoption of good RIDM practices in Canada, U.S. and beyond.

Feb 22, 2026

By H. K. Lin

Elemental sulfur is founded to be the predominant sulfur-containing species in a leaching residue resulting from ferric chloride leaching, under given conditions, of a chalcopyrite concentrate. The mineralogical study of the leaching residue which consists of 52% elemental sulfur reveals that the sulfur formed at the end of leaching process is in the form of discrete crystal rather than coating film. Flotation has been applied to recover the sulfur successfully using xanthate as a collector. Dispersants arc needed to prevent the mechanical entrapment of silicate and quartz by sulfur. Very high recovery of sulfur with satisfactory grades can be achieved with a relatively simple notation scheme.

Jan 1, 1991

By Wayne D. Gould

Planning for a project does not start with the announcement of the approval for a project. Planning actually begins when the project is only a prospect and it involves the years of experience of many people because their expertise influences the final decisions. In partial anticipation of the Pinto Valley project, as well as a search for improvement in the Copper Cities operation, two projects were undertaken. The first project was to substitute one 26" cyclone for three 20? cyclones in the single stage grinding circuit. The second project was to replace the Hunt air flotation cells with 300 cubic foot mechanical cells. The 300 cubic foot cells were just being introduced, consequently two types of cells were selected for testing. The results from both projects influenced the decisions on equipment for the Pinto Valley project.

Jan 1, 1975

By William Gleason

Since 2004, Dave Kanagy has served as the executive director and chief executive officer of SME. In that role, he has worked with 22 SME Presidents, traveling the world to represent the Society. His prestigious one-million-mile status with United Airlines is a testament to these efforts. He has been to six of seven continents while leading the Society on a journey from a struggling association in 2004 to the largest and arguably the most influential professional mining society in the world. In the following pages, some of those past SME Presidents reflect on their time with Kanagy and paint the picture of a visionary leader who was willing to make the hard decisions for the betterment of the Society while remaining open to new ideas and opportunities. One of his first accomplishments as the executive director was to streamline the SME Boad of Directors from 29 members to nine, making it much more effective. With a keen financial sense, he was able to add value while cutting excess to expand the Society in every measure. As the leader of SME, Kanagy helped facilitate much of the Society’s growth and innovation as the world’s largest mining related organization. He has a B.S. degree in industrial education from the University of Maryland, an M.S. degree in technology education from Eastern Illinois University and is a certified association executive by the American Society of Association Executives. Under his leadership, several unique programs were created or advanced, including OneMine.org, the world’s foremost online mining research library. He enhanced legacy programs and increased collaboration with international organizations. Kanagy is the recipient of prestigious awards, including the Colorado Society of Association Executives’ Professional of the Year award and the Mining and Metallurgical Society of America’s Gold Medal award.

Feb 1, 2026

By Shani Engelbrecht, Belinda McFadzean, Avuyile Wali, Natalie Shackleton, Vratislav Malysiak

Frothers play a crucial role in sulphide and PGM ore flotation recovery, and AECI Mining Chemicals studies on PGM ores have shown significant flotation kinetic increases with the optimal frother-collector combinations. Using Senfroth 200 as the industry baseline, remarkable kinetic increases were observed with AECI Mining Chemicals developed frothers in the first concentrate. Even in the worst-case scenarios, 4E PGM recovery increased by 5% at a slightly higher concentrate grade. It is important not to limit frother dosage to a fixed value. Instead, enough frother should be added to maintain a stable bench float, measuring the dosages by frother volume before and after tests. Frothers can be specialized blends and their importance should not be underestimated. The results produced by formulating and innovating frothers to address specific industry challenges have been encouraging. Testing a frother on a plant scale does not have to be as daunting as with collectors, enabling the identification of the best frother-collector combinations at an industrial scale. AECI Mining Chemicals bench scale testwork has motivated plant-scale trials that have successfully transitioned to commercialization. This paper compares the results from metallurgical and froth stability tests and shows that occasionally frothers that have a less stable froth can have improved valuable mineral recoveries, while still exhibiting better drainage for reduced entrainment and mass pull. It was shown that caution should be used when relying only on simplified froth stability tests in the evaluation of new frothers.

Feb 1, 2025

By Samuel A. Rasmussen

Lead anodes are used in commercial copper electrowinning operations, yet there is no method to calculate anode life. To be discussed in this paper are operating characteristics of rolled plate (Pb,Sn,Ca) alloy anodes at Morenci's electrowinning tankhouse along with fundamental operating conditions and how the anode reacts to these conditions. These include anode maintenance, electrolyte temperature and viscosity, cobalt concentration, and manganese concentration. Also to be discussed are anode substrate characteristics under normal operating conditions and how the corrosion rate is affected by changes in operating conditions.

Jan 1, 1995

By R. Frim, S. D. Ukeles

The present U.S. production of bromine is from inland brines located in Arkansas and Michigan. The most concentrated domestic brines (up to 5,000 ppm bromide) are situated in Arkansas. Less concentrated brines (about 2,500 ppm bromide) are located in Michigan. The amount of bromine sold or used in the United States came from three companies operating in Arkansas and Michigan. Arkansas, with its six plants, was the leading U.S. state in bromine production. Bromine being the leading mineral commodity valuewise produced in the state. The Michigan bromine production was a byproduct of magnesium compounds production.

Jan 1, 2006

By Kenneth K. Landes

So far my consulting in industrial minerals has been confined principally to carbonate rocks,-salt, coking coal, and glass sand. Much of this work has been for companies either too small for a full-time geological staff or unaware of the value of employing one or more qualified geologists permanently. It gave me considerable personal satisfaction to see several of the latter companies employ one or two full-time geologists after the completion of a consulting contract with them. One possible reason why some companies lack the wisdom to hire geologists is that they are dominated by engineers who still subscribe to the old idea that engineers are self-sufficient in all fields. They could have learned this from their professors. I once knew a Dean of Engineering who got purple in the face when a faculty committee was discussing the financing of a broad gauged engineering project and suggestions were made that assistance be obtained from the Schools of Business and Law and from some of the science departments tie pounded the table and shouted "Engineers are trained to handle all this!" In teaching engineering geology some years ago I used to tell the class repeatedly that the course would not make them geologists, that the purpose was to teach them

Jan 1, 1972

By Fathi Habashi

THE MINERAL monazite (µ?v??e?? = to be alone) is a rare earth phosphate containing some thorium and small amounts of uranium. It is widely distributed in the earth's crust. It occurs in small proportions in granites. Table 7-1. Mineralogical analysis of Rosetta black sands, U.A.R. (Nakhla, 1958). [Black sands Concentrate Augite 10.8 - Calcite 1.1 - Felspar 0.1 - Garnet 1.8 - Hornblende 2.4 - Ilmenite 50.7 8.0 Magnetite 15.3 Monazite 1.1 84.3 Quarz 7.3 - Rutile 1.0 0.5 Titanite 0.2 - Zircon 7.3 7.1 Others 1.0 0.1 100.0 100.0]

Jan 1, 1970

By Karl R. Zipf

A tube bundle system (TBS) is a mechanical system for continuously drawing gas samples through tubes from multiple monitoring points located in an underground coal mine. The gas samples are drawn via vacuum pump to the surface and are typically analyzed for oxygen, methane, carbon dioxide and carbon monoxide. Results of the gas analyses are displayed and recorded for further analysis. Trends in the composition of the mine atmosphere, such as increasing methane or carbon monoxide concentration, can be detected early, permitting rapid intervention that prevents problems, such as a potentially explosive atmosphere behind seals, fie or spontaneous combustion. TBS is a well-developed technology and has been used in coal mines around the world for more than 50 years. most longwall coal mines in australia deploy a TBS, usually with 30 to 40 monitoring points as part of their atmospheric monitoring. The primary uses of a TBS are detecting spontaneous combustion and maintaining sealed areas inert. The TBS might also provide mine atmosphere gas composition data after a catastrophe occurs in an underground mine, if the sampling tubes are not damaged. TBSs are not an alternative to statutory gas and ventilation airflowmonitoring by electronic sensors or people; rather, they are an option to consider in an overall mine atmosphere monitoring strategy. This paper describes the hardware, software and operation of a TBS and presents one example of typical data from a longwall coal mine.

May 1, 2013

By V. Svalbonas, S. M. Jones, A. Boughey

In June 1998, the world's largest grinding mill, the 40 ft (12.2 m) diameter 20 MW Cadia gearless SAG mill, was commissioned. This was a leap of over40% above the largest operating SAG mill. A significant saving in capital cost gave the incentive necessary for a single mill line at Cadia, resulting in the selection of the 40 ft (12.2 m) diameter mill. Now, after 18 months of operation, this paper will review the significant items involved in the development, design, manufacture, installation, and operation of this mill.

Jan 1, 2000

By Arthur W. Ruff

Estimated reserves of high-grade iron ore at Serra dos Carajás total 16 billion metric tons and have an average grade of 66.7 percent iron, 2.2 percent combined silica and alumina, and 0.05 percent phosphorous on a dry basis. Hematite is predominant and no significant sulfur or other deleterious elements are present. Figure 1 illustrates the comparative magnitude of the Carajás reserves. Serra dos Carajás is located in northern Brazil, about 550 kilometers southwest of Belém, Pará. It is six degrees south of the equator between the Xingu and Tocantins Rivers. Both rivers flow northward toward the Amazon River. The greater part of the area is covered by thick jungle, and the most practical means of access is by air. Figures 2 and 3 show the location of Serra dos Carajás. Figure 4 shows the distribution of the major iron-ore deposits.

Jan 1, 1973

By E. J. Karges

[For reasons well known to Mining Engineers, fine grinding in the wet form is quite universal inn plants engaged in the traction of metallic values from crude ore In the processing, of non-metallic and industrial minerals, however, fine grinding in dry form is the more common method. The crude materials generally contain less moisture than required for wet grinding, and the products are usually marketed or used in the dry form, most of them as powders. To grind wet would therefore entail the addition of water and the expense for drying the product, which is not justified. This paper will concentrate on the particle size reduction or fine grinding of materials to produce a dry powder]

Jan 1, 1963

By Sandeep Kumar Jeripotula, Govinda Raj Mandela, Aruna Manglapady

Dozer operators are frequently exposed to whole-body vibration (WBV) during the execution of their work. Occupational exposure to WBV in Indian surface coal mines was evaluated by measuring vibration intensity and duration of exposure. A triaxial accelerometer was placed on the operator seat surface for taking the readings. Based on frequency-weighted root mean square acceleration equivalent to 8-hr shift duration, i.e., (A(8)) all dozer operators have exceeded an Exposure Action Value (EAV) of 0.5 m/s2 , and 90% of dozers did not exceed Exposure Limit Value (ELV) of 1.15 m/s2 . Based on Vibration Dose Value (VDV (8)), all dozer operators have exceeded Exposure Limit Value (EAV) of 9.1 m/s1.75, but no dozer operators have exceeded Exposure Limit Value (ELV) of 21 m/s1.75. Further, an epidemiological study was performed for identifying the extent of musculoskeletal disorders (MSDs) among dozer operators. For the detailed study, 42 dozer operators and 22 controls were selected from 2 surface coal mines. The control group was not exposed to WBV. It was seen from the cross-sectional study that pain in the lower back was predominantly higher (83.33%) in the exposed group when compared with the control group (31.81%). Likewise, pain in the neck (47.61%), shoulder (42.85%), knees (42.85%), and ankle (11.90%) was higher in the exposed group than that of the control group (22.71%, 0%, 45.45%, and 4.54%). A significant observation among the exposed group was that there was degradation in the quality of life. The outcome of the study would assist in monitoring and mitigation of machinery-induced vibration diseases (MIVD) in India and generally applicable to most of the mechanized mines as well. However, comprehensive studies are still needed to enunciate the magnitude extent.

By David Newman

"Horizontal stress can have a profound effect on the stability of an underground limestone mine. The presence of horizontal stress is usually determined once the mine has been developed and the orientation of headers and crosscuts are well established. Multiple attempts are typically made to control roof falls without re-orienting the mine. Once the decision has been made to change the orientation, pillar centers, mine opening widths, and the question of how to determine the correct orientation must be answered.A case history is presented to illustrate how geologic structure, ground conditions and roof falls in adjacent mines, the World Stress Map (Heidbach et al., 2016), in-mine measurement of “cutter” roof orientation, the orientation of strata offset (cats eyes) within borescope holes, and the diametral deviation method of determining horizontal strain from drill core were used to establish the most likely range of horizontal stress.The main headers were re-orientated in a direction parallel to the median of the range of horizontal stress. The crosscuts were angled 60° to the headers to avoid being perpendicular to the horizontal stress direction. Pillar centers and opening widths were increased in the favorable stress direction of the mains and decreased in the less favorable crosscut orientation. The major principal horizontal stress magnitude was estimated using the strain measurements from the diametral deviation method and elastic modulus obtained through testing.INTRODUCTIONOver the past decade, there has been a significant increase in the number of underground stone mining operations in the United States. As stripping ratios at surface quarries become uneconomical and reach the extent of the mineral boundary, coupled with the encroachment of urban development on previously rural mining operations, the remaining mine reserves are best accessed through underground development.Although the majority of underground limestone mines in the Midwest are in relatively flat lying deposits with minimal geologic structure, many Appalachian mines are in folded and faulted environments. Tectonic horizontal stresses associated with multiple orogenic episodes are locked in the formation and are released as the underground mine is developed.A common misconception is that horizontal stress impacts are more prevalent at shallow depths where the ratio of horizontal to vertical stress may be high. However, field observations and academic research indicates that horizontal stress conditions may be encountered at any depth due to the tectonic compression of the limestone formation (Esterhuizen et al., 2007; Dolinar and Esterhuizen, 2007; Iannacchione et al., 2003; Slaker, Murphy, and Miller, 2017; Kuhnhein and Ramer, 2004). This paper outlines mine design and layout guidelines for the mitigation of horizontal stress impacts on underground stone mining operations through a case history example. This approach to mine planning and the ability to anticipate horizontal stress can significantly improve future production of multiple levels (Newman and Newman, 2019). As underground stone production continues at deeper depths and in more geologically and geometrically complex mining conditions, an emphasis on ground control and the anticipation of horizontal stress can provide safer and more productive single and multiple level mining operations."

Jan 1, 2019