Search Documents

By G. Deschênes

In Part I of the work, gold and silver were shown to be efficiently extracted from Kupol samples using lead nitrate in a cyanide leach system. In Part II, a comparison of the technical and economic merits of a new technology called CELP (CANMET Enhanced Leaching Process) was made with the cyanidation/AVR(Acidification-Volatilization-Recycling) process using 8 metallurgical variability samples as well as a large composite sample which represented initial two years of Kupol mill feed. The composite sample had 33.4 g/t Au and 289 g/t Ag. The metallurgical demonstrated that the CELP produced very similar gold and silver leach extractions compared to the standard Cyanidation /AVR leach conditions at 1/2 the cyanide concentration (1000 ppm NaCN in CELP vs. 2000 ppm for cyanidation/AVR leach conditions). It was estimated that the total cost per ton, were approximately the same for the two technologies (total cost of the CELP with the use of Merrill-Crowe at $46.48/ton, with cyanidation/AVR at $46.13/ton). However, the implementation of the CELP would eliminate a capital expenditure of approximately $5 million. Eight variability samples used to confirm the previous results showed that on average the gold and silver leach extractions with the CELP and the feasibility leach conditions were very similar for gold extractions, but 4.6% higher for silver extractions compared to the conventional cyanidation. The decision was made to remove AVR cyanide recovery from the Kupol flowsheet and implement the CELP at Kupol. The ability to use conventional leach equipment with the CELP and simplify the flowsheet was also a factor, given the remote location of the Kupol Mine.

Jan 1, 2009

By John Fred Rivera

Since its inception during the hectic days of World War II, Kaiser Steel Corporation has developed and maintained a solid reputation as a progressive company with an incessant penchant for attempting innovative ideas to improve its stature in the American and world corporate framework. The very latest in technology is aptly demonstrated in the new Basic Oxygen Process recently placed into operation at Kaiser's huge Fontana Steel Mill. Daring ventures such as this and other developments on pollution control devices have propelled Kaiser Steel Corporation into the forefront as the largest steel producer in the western United States. Kaiser Steel's boldness and willingness to attempt new ideas and the very latest in technology is by no means limited to its steelmaking operation. It extends into every phase of Kaiser's corporate structure.

Jan 1, 1979

By A. Jolly, A. R. Kumar, T. Novak

"Coal dust in an underground mining environment has always been a health and safety issue, especially with longwall faces. Efforts to integrate a flooded bed scrubber within a longwall shearer are underway at the University of Kentucky (UK) in order to reduce worker exposure. Small scale physical modeling, along with numerical modeling and full-scale experimentation, are engineering tools being used by the authors for simulating operating conditions underground. Recent advances in affordable 3D printers offer a means for fabricating accurate, scale models for obtaining timely insights prior to building large, expensive test setups. Comparing scale-model results with those of numerical modeling, such as computational fluid dynamics (CFD), lends guidance and confidence in a proposed design. This paper discusses the small scale physical modeling of a longwall shearer with an incorporated flooded-bed dust scrubber in its operating environment. A tracer gas was used in the model in lieu of dust to measure dust-capture efficiency. Results obtained from the physical model are presented and compared with those of CFD model. The small scale model and the CFD results demonstrate good agreement. Dust capture results show the usefulness of the approach in advance of actual design implementation. INTRODUCTION Dust generation is an undesirable, but innate, byproduct of all mining processes. It is particularly problematic in underground coal mining, where coal dust poses potential hazards from two fronts – health and safety. Coal workers’ pneumoconiosis (CWP), commonly referred to as black lung, is a chronic lung disease that results from the long-term overexposure to respirable coal dust. Although the prevalence of CWP has steadily and significantly declined over the three decades following the Federal Coal Mine Health and Safety Act of 1969, a study by the National Institute for Occupational Safety and Health (NIOSH, 2008) indicates that significant health hazards associated with respirable dust still exist within the coal mining industry. In addition to being a health hazard, coal dust can also create a potentially catastrophic safety hazard. Dust that is not captured or removed at its source is suspended and transported throughout a mine by the ventilation airstream. This float dust is subsequently deposited on all mine surfaces along its travel path. Without adequate application of rock dust to these surfaces, forces from a localized methane ignition can reintroduce settled coal dust into the airstream creating an explosive mixture. Therefore, capturing and removing coal dust at its source mitigates the probability of two major hazards that continue to plague the mining industry."

Jan 1, 2016

By Wen Tao Liu, Tong Tian, Fu Sheng Niu, Xiu Man Liang

The level of automation employed in flotation production is relatively low. In an actual concentrator, operators use their judgment to adjust the production state based on the visual characteristics of the flotation froth surface. There are shortcomings, such as strong subjectivity and lagging process operation, that easily cause the waste of manpower and material resources. Machine vision technology is introduced to replace human visualization, achieving a quantitative description of the visual characteristics of the froth surface. The state variable parameters are provided for the identification of the flotation conditions.

By K. Dagdelen

The definition and shortcomings of traditional cutoff grades are discussed. The concept of optimum cutoff grade policy which maximizes the Net Present Value (NPV) of annual cash flows coming from a mining project is introduced within the basic framework outlined by K. F. Lane. Several examples are used to demonstrate the shortfalls of cutoff grade policies obtained by various heuristic optimization techniques. An algorithm to obtain an optimum cutoff grade policy which maximizes the NPV of a project is given and described in detail.

Jan 1, 1993

By P. Mills

The four top barite-producing countries in the world are China, India, Morocco and the United States. China is currently the largest exporter of barite followed by India. More than 95 percent of the barite mined today is used by the petroleum industry as driller’s mud. The rest is used in the industrial market and the medical field. Most of the barite mined in the United States is in Nevada. This year, mining activity has increased due to an increase in oil exploration/development. This was caused by an increase in the crude oil prices.

Jan 1, 2005

By Simon E. Rodriguez

This paper presents sulfur isotope data obtained for the deposits and country rocks of the Bailadores and Aroa Mining District, Venezuela. The study is a part of an extensive geochemical investigation of the mineralized belts that has as their aim the elucidation of the genesis of ores. The Bailadores deposits are located at about 600 Km. west-southwest of Caracas, or about 10 Km. southeast of the Town of Bailadores, Merida State (Fig. 1). The mine concession is held by the Ministry of Mines and Hydrocarbons (De Lima I, De Lima II and La Cascade areas). In a straight distance the mine is about 90 Km. southwest of Merida, the capital of Mérida State. From Mérida to Bailadores, through La Victoria and Tovar, it takes 3 hour by car. From Bailadores to the mine site it is about 40 minutes by jeep. The Aroa deposits are located at 4 Km. east of Aroa Village, Yaracuy State, about 220 Km. west of Caracas. It is 83 Km. from San Felipe, the capital of Yaracuy State to the mine (Fig.2). The mine is about 600 m above sea level, situated on the northern foot of the E-W trending Andes. The topography of the mine are shows a mature stage and is somewhat rugged. As the climate is warm and humid, the area is thicky covered with jungle.

Jan 1, 1974

In the screening process, used to prepare particles for many applications, shape is known to have a significant effect. The degree of flakiness of construction aggregates has been considered particularly important. The objective of this research was to find values of operating parameters that optimize the separation of flaky from non-flaky particles by slotted screens. Thus an investigation was conducted to experimentally determine the influence of the particle size and thickness on the screening process. The Response surface method was employed for modelling and analysis of the data. Experiments employing a central composite design were performed on a pilot-scale, rectangular-aperture, vibrating screen to examine the effects of the screening variables the mass recovery of flaky and non-flaky particles to the oversize product. The SAS statistics package was used to fit a second-order model to each response and to analyze the fitted surface to determine the optimum levels. The optimization associated with a dual response system was then considered. The results of this study should provide a basis for optimizing screening conditions to obtain maximum recovery of non-flaky particles to the screen oversize while minimizing the recovery of flaky particles, which should be of interest to the aggregate industries.

Jan 1, 1999

By F. J. Susko

The Bureau of Mines applied a flotation model to the hydrodynamics of the Bureau-developed rapid flotation system. Rapid flotation is a process which separates the bubble-particle attachment and froth-pulp separation stages of the flotation sequence into two discrete unit operations allowing the operations to be individually optimized. Both an air-injected hydrocyclone and an in-line mixer were used as the bubble-particle attachment unit and a shallow-depth froth separator was used to separate the ore-laden froth from the pulp. A 10-L/min batch system was tested on a coarse coal feed sample. The system was tested using two different bubble-particle attachment units at various aeration levels in order to test the flotation model. The results of the flotation model reflect general trends observed in the experimental data.

Jan 1, 1993

By Arvid E. Anderson

The paper describes the unique operating features of the Lebanon Concentrator Plant wherein both magnetic concentration and froth flotation are used. Chalcopyrite is selectively floated by the use of dual collectors, Aerofloats and secondary butyl xanthate. Both potassium ethyl xanthate and sodium isopropyl xanthate (dual collectors) are dissolved and emulsified with pine oil for the flotation of the pyrite. Sketches describing the plant operations are presented and plant operating metallurgical results obtained are also given. The optimum production of minerals by the froth flotation process is normally achieved [ ] smooth operating conditions, The process, because of its many variables, becomes an art as well as a science. Therefore, any phase of the operation which will aid the operator in his control of the numerous variables will help produce a smoother operating plant, One of the most important variables which the operator deals with is the addition of reagents, These are usually costly items and should be used discretely with minimum amount of waste, The danger is that ,this emphasis may reduce the reagent amount to a point below that required, or, on the other hand an excessive amount is added, Both conditions usually yield poor results. The drea of the metallurgist is to provide the operator with the tools enabling him to produce a good mineralized froth at all times. Normally the operator has no control concerning the type of reagents which he must use. This has usually been worked out for him in the laboratory and by plant-scale tests. He does have limited authority to control the amounts of the reagents at his disposal. This, I believe, is as it should be. However, the operator should be provided with the best combination of reagents for his particular job. The providing of this combination of reagents for his particular job, The providing of this combination is often difficult, yet it is very important in order to yield good results, With this in mind, the dual collector idea was introduced for the selective flotation of chalcopyrite, and also later for the flotation of pyrite at the Concentrator Plant of the Bethlehem Cornwall Corporation in Lebanon, Pennsylvania, Supplying several types of collectors has given the operator an additional effective tool, even though great variations are encountered in ore tonnage treated and in ore composition, This paper deals with the use of the dual collectors and with the addition of the reagents in the form of a pine oil emulsion, or more accurately, a pine oil suspension. It is hoped that other operators may find the ideas helpful. There does not seem, to me, to be definite scientific fact which would substantiate the necessity for the use of dual collectors. However, in actual operations, the metallurgical results at Lebanon became more uniform with the use of dual collectors, I look upon it as an "insurance policy" which greatly aids the operator during those periods when he is having trouble, One theory has been advanced, i.e. one collector has a greater tendency to float the coarser minerals, whereas the other one may float the finer ones. Consequently, a combination of the two collectors will result in optimum recoveries, There has been some evidence that this is true, but it is not conclusive, on the other hand, the use of a xanthate-pine oil suspension (or emulsion) should speed up the surface reaction of the collector with the sulfide minerals, result¬ing in more uniform flotation, This has definitely happened in our particular case. A more interesting unexplainable observation has also occurred; i.e., the xanthate solution does not appear to lose its strength as rapidly when it is in the form of an emulsion (or suspension), This was first observed when a 50 gallon drum of a 20% ethyl xanthate solution was taken to Wilmington, Delaware, for a laboratory test, using a homogenizer to produce the xanthate-pine oil emulsion. Upon arrival, the drum of xanthate had developed a considerable internal pressure, The relief of this pressure was accompanied by a strong odor, When the emulsion was returned to Lebanon for the plant test orders were issued to release the pressure prior to emptying the emulsion. Nopressure had developed within the drum and there was no unusual odor present, Since this time it has been observed that xanthate pine oil suspensions have greatly decreased the possible decomposition of the xanthate solutions. In fact, suspensions have been exposed for more than a month without apparently effecting their reactions in the flotation plant. On the other hand, we found that the regularly mixed concentrated xanthate solutions, after standing for several days, did not give the same results as the freshly made ones. This effect was greatly reduced by the use of xanthate pine oil suspension (or emulsion)

Jan 1, 1958

By J. E. Friant

The Mini-Disc TM cutter drill bit is a radical design departure from the traditional tri-cone rock drill bit. Miniature disc type cutting tools as small as 3.25 inches (82.5 mm) diameter are fitted to a bit body to cut individual concentric kerfs. The action is the same as that commonly used on large tunnel boring machines but miniaturized. The high performance rate and efficiency of a disc cutter are the result of producing a large proportion rock chips rather than sand or powder. The Mini-Disc TM drill bit, referred to as the "Disc Bit" has other unique features as well. It can be re-greased between runs. It can be rebuilt in the field in about 15 minutes, cutters can be replaced and the Disc-Bit appears to require less down hole hydraulic power than conventional bits. Thoroughly tested in the laboratory, the bit has recently been undergoing field trials in well drilling, blast hole drilling and shaft drilling. As any engineer knows, the laboratory cannot shake out all the problems but it eliminates the more glaring weaknesses. Performance results have been exhilarating, and a few mechanical problems were discovered and largely overcome. This paper is a progress report.

Jan 1, 1999

By Andy Ingriselli, Andrew Famiglietti, John Westland, Greg Landry

Atlas Dewatering was contracted to install and maintain a groundwater control system for the new Bessarion Subway Station and the Tail Track Structure on the Toronto Transit Commission’s new Sheppard Subway Line. Atlas met the challenges presented by the project by closely reviewing the contract documentation provided by the Program Geotechnical Consultant, Golder Associates and by working with the general contractors, Bondfield Construction Company and PCL Constructors Eastern, inc., throughout the duration of both projects. In addition to concerns about soil loss, excessive settlement and seepage, the consultant was concerned about spreading hydrocarbon-contaminated groundwater between the two aquifers present at the Bessarion Station site. By installing a system of multi-level vacuum eductor wells around the perimeter of the excavation, Atlas was not only able to provide a dry excavation for construction, but, due to a unique well design was also able to prevent cross-contamination of the aquifers.

Jan 1, 2001

By Frank E. McCall, John K. Marshal, Fred Garcia

Since the advent of longwall mining systems in the United States, mine operators are increasingly relying on methane drainage techniques to supplement the ventilation system. The most commonly used technique is the vertical gob borehole. The number and spacing of vertical gob boreholes per panel is generally based on experience and underground conditions. To design a more efficient methane drainage systems, mine operators must accurately determine methane gas produced. Thus, mine operators must monitor gas flow and methane gas concentration on every vertical gob borehole on active panels at least once or twice during each 8-hr shift. As the mine grows, it is possible to have more than one operating longwall and many vertical gob boreholes. Thus, daily visits to each vertical gob borehole site can become very time consuming. During weekends when methane gas concentrations typically drop because there is no mining activity, borehole sites may not be visited. To obtain accurate gas flow data, a gob borehole monitoring system was designed and constructed by the U.S. Bureau of Mines (USBM). Gas flow, methane gas concentration, gas temperature, barometric pressure, and vacuum pressure of the exhaust fan are the parameters collected by the system. The system also includes circuitry for automatic shutdown of the exhaust fan and an alarm system before an unsafe condition is created. Telemetry components were also integrated into the system to allow for transmission of borehole data to the mine office. As a test, the system was installed and operated on a vertical gob borehole for six months. Test results indicated that intermittent measurements with hand-held instruments from vertical gob boreholes were always higher than gas flows measurements made by the gob gas analyzer system. This paper describes the system components, operational characteristics, and the results of the test program.

Jan 1, 1995

By Carrie Smith

Mining has historically been one of the most male-dominated industries in the world. From underground operations to executive boardrooms, the presence of women has often been slim. Women had often been excluded from operational, leadership and decision-making roles, both by cultural norms and systemic barriers. According to PwC’s Global Mine Report (2023), women represent around 14 percent of the global mining workforce. Leadership representation, however, remains sparse, with S&P Global’s 2023 report showing women holding approximately 12 percent of C-suite positions and only 3 percent of senior leadership roles globally. These figures reflect persistent gaps, but they also highlight the progress driven by a new generation of women transforming the industry. Despite the gender imbalance among mining workers, women have continuously made grand strides within the industry, resulting in pivotal changes. At the forefront of this transformation is Kimberly Morrison, one of several women who have played pivotal roles in shaping the mining sector.

Aug 1, 2025

By P. M. Soupios

A near geophysical surface investigation of a landfill area close to the Hania city, in Crete Island, Greece, was conducted as inextricable phase of a preliminary geotechnical, geological and hydrogeological study of the area under investigation. Electrical Resistivity Tomography (ERT), one of the most promising prospecting techniques mainly concerning its effective contribution to resolve several environmental problems, was applied for the geophysical modelling. ERT is a robust imaging method the theory and implementation of which are well documented in geophysical research literature. The survey site is located in Akrotirion Peninsula, about 7km east of Hania city in Crete I. The geological setting comprises Trypalion limestones, marly limestones and a clayed weathered layer. Cavities are also identified at various scales which are recent tectono-karstic voids resulted from the combined actions of karstic erosion and tectonic stress on the Trypalion limestones where they are located. Due to the above-mentioned geological singularity and in the light of the requirement for an environmentally safe construction of the landfill, an ERT survey was carried out by deploying the dipole?dipole electrode configuration. Specifically, seven geoelectrical tomographies were conducted reaching the prospecting depth of 36m. The resulted images conduced, a) to overcome geotechnical problems, b) to plan the future sites for waste disposal and c) to reliably estimate the thickness of the already deposited wastes.

Jan 1, 2005

By David T. Kao

The energy situation the world faced during the decade of the Seventies resulted in actions throughout the free world to reduce its dependence on OPEC oil. Many nations heeded the indicators early in that decade and commenced efforts to reduce their oil requirements. Those nations which did not heed these warnings had the message brought to them more emphatically in the last portion of the decade with the further rapid and continuing rise in prices of OPEC oil. Furthermore, the demonstrated unstable nature of large oil-producing countries has made it clear to all free world nations that their energy demands of the future must be provided for by some more stable and assured supply. Now, early in the decade of the Eighties, we see the need for expanded use of coal as an energy supply to be essential. The result in 1980 and 1981 has been a great increase in demand for steam coal worldwide. In essence, a new business for the United States has developed in steam coal export. In the United States, the large growth in foreign demand for our steam coal is now well recognized and documented. A major impediment in meeting this growing demand became abundantly clear in 1980. This impediment is the congestion existing at U.S. coal export ports. With the recognition of this constraint, a plethora of activity has been observed in announcements for alleviating the problem by improving and expanding current export port facilities. In addition to improvement and expansion, an abundance of totally new facilities has been announced in an effort to find ways to meet this large demand in the new business of steam coal export. This is needed; and hopefully, many of these plans will be translated into action. While total implementation of all stated plans is not expected, much of the implementation depends upon large- scale dredging, large waterside ground storage sites, and improved handling equipments in the conventional type of export ports. The time and capital required for implementation is great, and environmental problems associated with dredging are substantial. Host significantly, and unfortunately, implementation that does include dredging our ports will still not permit use of the truly large colliers of 140,000 DWT and greater, which are evolving as the "state of the art" in long-distance sea transport.

Jan 1, 1981

New Mexico?s active coal mines have reclamation challenges that are being successfully resolved through the application of geomorphic grading methods. Soils and overburden material are often of poor quality, and annual precipitation is low. Revegetation on south and west aspect slopes often failed to persist. The New Mexico Mining and Minerals Division had therefore been encouraging topographic diversity on reclamation to improve water harvesting and reduce the percentage of south aspect slopes. Steeply dipping, multiple coal seams may be mined by open pit methods. Structurally-controlled trellis drainage patterns that exist premine have to be replaced with dendritic drainage patterns on reclamation where the overburden had been pulverized. Sodic spoil material is prone to differential settling and the creation of piping features in areas where runoff ponds, which may lead to downslope instability. In each of these scenarios, the approximation of natural drainage patterns on the reclamation has reduced erosion and sedimentation by creating shorter slopes with correct profiles, and by improving conditions for revegetation establishment.

Jan 1, 2010

By D. C. Martin

Stability analysis and design of open pit slopes is generally based on an assessment of rock cores and rock exposures on surface or in underground workings. Until recently, core for such assessments has been readily available from exploration drilling programs. In recent years, many exploration programs have reduced the amount of coring and rely more heavily on less expensive rotary or percussion drilling programs where drill cut-tings are sampled for geological evaluation and assay. This paper describes a technique whereby costs of the geotechnical investigation are reduced by using rotary percussion drilling information to assess geotechnical properties of the rock mass. A limited number of core holes are required to establish basic relationships between the mechanical properties of core and the characteristics of the percussion chips. These properties are used as a basis to extrapolate the coring information to encompass the entire area of the rock mass for which percussion drilling information is available.

Jan 1, 1990

By Terry Owen

Not since 1917 has a foreign company developed a standalone, grass roots gold mine in Russia. With Russia's political changes of the late 1980s, development of mineral prospects once again beckons foreign investors. Cyprus Amax's interest in Russia began before the mid-1991 breakup of the former Soviet Union. In 1990, Cyprus Amax began searching for such an opportunity. Early this year, production will begin at the Kubaka gold project located in the Russian Far East, near the Arctic Circle. The Kubaka project is a 1.75-kt/d (1,930-stpd) open-pit operation that will produce more than 9.3 t/a (300,000 oz/year) of gold. Identifying Russian mining opportunities In late 1990, the first Cyprus Amax people travelled to Russia. The trip was to determine the potential for western firms to develop profitable mines. This encouraging visit suggested that Cyprus Amax focus on the Russian Far East with its mineral riches and its easier access to the United States. The company's initial efforts thus focused on working with the Soviet Union's Northeast Geologic Expedition, the then government agency for exploration and geology in Russia's Far East. After the breakup of the Soviet Union, Cyprus Amax continued working with the same people, but they now represented new independent, nongovernmental entities. For three years, Cyprus Amax investigated numerous deposits. This resulted in the identification of two properties of significant interest, one of which was Kubaka. Location Kubaka is located in the Northern Evensk District of the Magadan Oblast in the Russian Far East. This is an area east of Siberia. The project is situated in a mountainous area of the Kolyma Range, about 300 km (985 miles) south of the Arctic Circle. It is 285 km (180 miles) north of the fishing village of Evensk and 380 km (235 miles) northeast of the silver-mining town Omsukchan. The site is 950 km (590 miles) northeast of the regional capital city of Magadan. Magadan, the political and economic center of the Oblast, has a population of about 150,000 people. It is served by a year-round deep-water port (with icebreaker assist) and an international airport with service to Moscow and Anchorage, AK. Access to the Magadan region

Jan 1, 1997

By Yi Luo, Jian Yang, YUJIA LIAN

Scale physical models, constructed according to the principle of similarity theory, have been widely used to simulate the mining disturbances to surrounding strata and to evaluate the effectiveness of implemented ground control techniques. This technique has also been used for studying mining-induced surface and subsurface subsidence. The movements of the observation points installed on the physical model at different mining stages are currently measured using total station which is time-consuming and inaccurate especially on small scale models. A photogrammetry-based measurement system has been developed. During a physical modeling process, photos of the model can be taken during the simulation process reducing survey time from hours to a few seconds. A program, Photogrammetry Analysis for Physical Modeling of Mine Subsidence Process (PAPMMSP), developed based on photogrammetric principle is used to quickly identify the installed observation points and accurately determine their coordinates. The measurement accuracy is well under submillimeter level—an ultra-important advantage as any measurement errors in coordinates are magnified by the model dimension scale (commonly 20 to 400). A physical modeling case of subsurface strata movements and deformations associated with longwall mining operations is presented in the paper to demonstrate the functions and capabilities of the developed photogrammetry program.

Aug 11, 2020