Search Documents

By Behrooz Abbasi, Seyedsaeid Ahmadvand, Thom Seal, Babak Azarfar, Bryan Ulrich

Hydro-Jex® is a new enhanced method for heap leach treatment with significantly higher mineral recovery. In this case study at the Los Filos Mine in Mexico, the Hydro-Jex operation is evaluated for heap leach stability. This is pursued by numerical modeling of the heap leach pad stability and well monitoring of the phreatic surface before and after the Hydro-Jex operation. Experimental and numerical results both indicate an improvement in mineral processing under the influence of Hydro-Jex. Numerical results show an insignificant decrease and a significant increase in stability during and after Hydro-Jex injection application, respectively. The integrity of the liner is maintained in both cases. The zonal injection pressure, operationally below the overburden pressure, is found to be negligible compared with the dimensionality of the heap, and stability of the structure is not exposed to any significant risk, even up to 25%above overburden pressure. Furthermore, heap leach factor of safety increases after Hydro-Jex application. This is attributed to breakdown of the water solution build-up and thus a decrease in the phreatic surface depth below the top of the pad. It is suggested that injection wells be drilled, based on thorough geophysical data, in locations where overcompaction of heap material results in water solution build-up and pore pressure enhancement. Compared with traditional heap leaching, the Hydro-Jex technique not only expedites mineral processing by increasing chemical kinetics extraction but also increases the stability of the heap by unclogging drains.

Jun 29, 2020

By M. J. Virnig, B. D. Boley, G. A. Wolfe, J. M. W. Mackenzie

A flowsheet for the recovery of nickel and cobalt from laterite ores has been developed which involves acid leaching followed by hydroxide precipitation of the metal values and then releaching of the hydroxide cake with ammonia. Investigations of the chemistry of extraction of nickel by LIX® 84-I and a developmental reagent, XI-84-IT, along with the physical properties of the organic phases are described. Based on these investigations, suggestions with regard to design of a solvent extraction plant and operating conditions are made.

Jan 1, 1999

By James E. McNulty

The planning and development of new coal mines is requiring the increased use of geologic, geologic engineering and hydrogeologic investigations. This is caused in part by the fact that new mines must deal with less favorable conditions than existing mines as well as higher costs of development and in part by the dictates of regulatory authority. High costs of new mines require greater reliability of geologic assessment using best available geotechnical and geophysical methods and technology. Although the increased cost of additional subsurface data is significant, the more important factor may be the impact on project lead time.

Jan 1, 1981

By E. -R. Niinikoski, M. A. Islam, H. Mischo, G. Barakos, J. Joutsenvaara, G. Meissner

European Union's transition to a low-carbon and digital economy highly depends on securing the strategic autonomy of the Critical Raw Materials (CRMs) supply chain. This paper introduces a European Commission-funded research and innovation action, AGEMERA, which aims to create detailed geological and people's concerns maps to unlock the CRMs potential in Europe. Furthermore, the project will develop educational packages for schools and universities, publish online CRM-related games and news flashes, and arrange public events to ensure a basis for socially accepted and sustainable exploration and mining of CRMs in Europe. 1. IntroductionCritical Raw Materials (CRMs), crucial for shifting to a low-carbon and digital economy, should focus on maintaining Europe's overall supply-demand balance (Birol, 2022). Therefore, to proactively address the surge in demand and ensure the strategic autonomy of European industrial supply chains, the exploration and extraction of CRMs must be scaled out across the continent. Moreover, mobilizing Europe's domestic potential is vital for the EU to become more resilient and to establish open strategic autonomy as the demand for CRMs continues to increase quickly on a global scale (European Commission, 2021). Base metal extraction and mining have a long history in Europe. Nevertheless, CRMs mining projects have shown less success, although these have a lot of potential (Guzik et al., 2021). The main barriers are a lack of investment in mining and exploration, complicated and drawn-out national permitting processes, and low levels of public support (European Commission, 2020). It is necessary to have a vast amount of knowledge and intelligence about CRM's potential and market impact. Novel non-invasive geophysical survey techniques that enable sustainable exploration must be created and used to enhance mineral system models of ore deposits incorporating CRMs. The minerals policy framework significantly influences the mining industry's performance, stability, and sustainability. However, the EU Member States' mineral policy frameworks differ significantly (MINLEX, 2017). In addition, the Fraser Institute Annual Survey of Mining Companies offers concrete information on how managers and executives of mining companies view key policy areas that impact mining activities in the jurisdiction in which they operate or are familiar (Jackson & Green, 2015).

Feb 1, 2023

By M Ali, E Satriawan, M Napitupulu, A Munandar

The Deep Mill Level Zone (DMLZ) panel cave mine is one of three active caving mines at PT Freeport Indonesia’s Grasberg Underground Mining Complex. The DMLZ mine is located at a depth of approximately 1,500-1800 m below the surface, making it one of the world’s deepest panel cave mining operations. This depth results in both high in-situ and induced stress that acts on the hard and massive rock mass, triggering rockburst conditions. As a result of the bursting conditions, ground support and maintaining the support capacity are an essential part of operating the DMLZ mine in an efficient and safe manner.

Apr 26, 2022

By Jung-Hum Lee, Young-Joon Lee, Eui-Joon Hong, Seon-Hong Kim, Chan-Dong Kim, Keon-Woong Jeong, Ki-Lim Kim

"Subsea tunnel needs to be built over 50km long to connect between nations and continents. However there are only 19 tunnels longer than 5km in Korea, and there is no history of constructing and operating a tunnel longer than 50km. As the concept of a subsea tunnel, which withstands high water pressure and has an extremely long length is completely different from that of a land tunnel, all kinds of the latest technologies for tunnel construction are required such as survey and analysis of geology, design and construction under high water pressure, ventilation and prevention of disasters within an ultra long tunnel. Therefore, this paper describes the determination of tunnel cross-section under a high speed railway, structural stability, ventilation and fire safety under construction and operation, etc. through the virtual project for the length of 108km subsea tunnel under high water pressure of maximum 20bars from Honam to Jeju island in Korea. 1. INTRODUCTION The Honam-Jeju virtual project is subsea tunnel project to link from Honam(land) to Jeju(island) extending the currently operating Honam high speed railway line, and the same express train(t=18, design speed 350km/h, total train length 200m) operating at Honam line is applied in this project. As Honam-Jeju site is approximately 80km in straight distance with 160m maximum depth, subsea tunnel project should determine the various issues such as air quality/ventilation, aerodynamics, temperature, drainage, fire & life safety, structural stability. Figure 1. is the plan of subsea tunnel, with be constructed using Shield TBM. This double tube-Single track is composed of cross passages (every 350m in general section and 40m in emergency station), service tunnel, pressure relief ducts (every 250m), cross-over tunnels, shafts and emergency stations. 2. ALIGNMENT AND SITE CONDITON This project is planned as an ultra long tunnel of total length more than 105km via existing islands between Honam and Jeju island because straight alignment requires an artificial island which has high cost and construction risk, by deep water depth, though this is the shortest distance (see Fig 2). Water depth and topography in project site is divided into two blocks by Chuja Island. In first block to Chuja Island, depth of the water is 40m on average and maximum 60m, which indicates gradual change of water depth relatively. Also, outcrop bedrock is widely distributed near island."

Jan 1, 2016

By E. Steel

The asbestifom habit is most commonly developed in certain amphiboles and chrysotile, but other minerals may also crystallize with this unususual habit, The habit may be characterized by 1) a fibril structure, single or twinned crystals of very small widths (generally less than 0.5 inn) which have gram with a common fiber axis direction but which are disoriented in the other crystallographic directions, 2) anomalous optical properties, primarily parallel extinction, 3) unusual tensile strength, 4) high aspect ratio, and 5) flexibility. In addition, there is evidence to indicate that some amphibole asbestos may have unusual surface properties.

Jan 1, 1979

By Mark J. Zdunczyk

"Frac sand is industrial silica sand much like glass, foundry, filtration and blast sand. The sand must meet certain specifications set forth by the industry that consumes the product. The production and consumption of frac sand has experienced record growth in the last 10 years because of new oil and gas drilling, new horizontal well drilling, multi-stage fracturing and the stimulation of older wells that have little or no production. Frac sand is needed to “prop open” the fractures in the rock reservoirs to allow oil and gas to flow out more freely.According to the U.S. Geological Survey (USGS), the estimated production of frac sand in 2015 was 71 percent of the total production of industrial silica sand or 67.4 Mt (74.3 million st). This is a decrease of about 12 percent from 2014. However, the silica sand industry and other industry sources estimate only 50 Mt (55 million st) of frac sand were produced in 2015. In recent years both the USGS and industry studies have been very close in estimating the production of frac sand but with the recent downturn in frac sand production, perhaps, reporting to the USGS was not as accurate. These discrepancies may be that the USGS statistics are based on voluntary reporting by the industry and some companies report their approximate production, others may not. It is always difficult to obtain accurate production figures of any industrial mineral or construction aggregate operation as most companies tend to keep those figures somewhat confidential. It is certainly accurate to report that the production of frac sand had decreased since the last quarter of 2014 and through 2015. The oversupply of oil and natural gas has led to this decline in frac sand usage. Oversupply has idled drilling rigs and well completion activities. World Oil Magazine reports that 2015 was the worst year for rigs in a quarter century. The only wells being completed are those that have contract agreements to do so, others have been capped. Very few new wells are being drilled. Since about 98 percent of well completion is sand and water, the sand supply has caught up with the demand. There are some bright spots in the “oil patch” as the Permian Basin in Texas and the Woodford Shale in Oklahoma have kept pace somewhat with drilling and completion. It has been reported that the frac sand producers in the Brady-Voca, TX area are producing to nearly capacity. The northern frac sand producers like those in Wisconsin, Illinois and Minnesota are feeling the downturn because of the cost of shipping sand to these moderately active basins and plays. The “rule of thumb” is that freight is 2/3 and sand is 1/3 the cost."

Jul 1, 2016

By W. R. Reed, G. W. Luxbacher

Mine worker exposure to respirable coal dust and silica dust can result in coal workers’ pneumoconiosis and silicosis which are occupational respiratory diseases that have no cure and are ultimately fatal. In 2021 the Mine Safety and Health Administration reported just over 11,000 operating metal/nonmetal mines with the potential for silica dust exposure for just under 200,000 miners. The National Institute for Occupational Safety and Health (NIOSH) conducts respirable coal and silica dust research associated with mining through its Office of Mine Safety and Health Research. NIOSH respirable coal and silica dust research began under the U.S. Bureau of Mines (USBM), which initially examined silica dust, progressing to include coal dust, with a stronger focus after 1969 with the passage of the Federal Coal Mine Health and Safety Act. A review of extramural research to develop real-time respirable silica dust monitor is presented along with a brief history of silica dust regulation.

Feb 1, 2024

By Justin R. Patts, Andrew B. Cecala, A. KYLE LOUK, Emily J. Haas

The National Institute for Occupational Safety and Health (NIOSH) and the former U.S. Bureau ofMines (USBM) have given a significant effort over the past four decades in researching and developing engineering controls and interventions to reduce mine workers’ dust exposures during the bagging and palletizing of industrial minerals. Workers performing manual bagging and palletizing of 50- to 100-pound bags typically have some of the highest dust exposures of all workers at mining and mineral processing operations. This paper will provide an overview of available dust control technologies for bagging operations and present the findings of a recent case study that was conducted at four different industrial sand operations to identify the current types of bagging and palletizing technologies being used and to evaluate their effectiveness in reducing workers’ exposures to respirable crystalline silica dust. An evaluation will also be performed to determine if further reductions in respirable dust levels can be achieved by incorporating additional modifications or improvements into the existing technology.

Apr 3, 2020

By Z. Hyder, M. D. Cleason

"INTRODUCTION Mine Ventilation has come a long way over the years. The main purpose of mine ventilation is to keep conditions in the mine safe for the worker so that the mine will be productive and profitable. Technological developments to the mine ventilation system itself and the development of mining techniques have helped improve the safety and productivity of the miners and the mine. Most of the developments to mine ventilation and to safety devices came as the result of serious mining disasters. Another effect of those mining disasters, especially in the late 19th century and after, was legislation to set specific safety standards for mines, especially in the underground coal mines. This paper will focus on the connection between mines disasters and the mine safety legislations promulgated because of those disasters. A BRIEF HISTORY OF MINE SAFETY LEGISLATION Mine legislation has a long history in the U.S. dating back well in the 1800’s. However, mine safety legislation is considerably newer. In 1891, the U.S. Congress passed the very first version of mine safety legislations setting up minimum safety standards. By today’s standards, the 1891 legislation was incredibly basic (7). It took a series of horrific mining disasters for Congress to take action a second time. In 1910, Congress established the Bureau of mines. The role of Bureau developed and changed over next 60 years. In 1995, Congress voted to disband it (27). Initially the Bureau was only charged with investigating and coming up with ways to reduce accidents in coal mines. It was not until 1941, when Congress formally allowed Bureau of Mines’ Inspectors into the mines. In 1947, the Congress enacted and adopted a set of federal safety regulations for the inspectors to follow (1). Finally, in 1952 Congress granted the Bureau of Mines the authority to inspect the mines and to issue citations and/or orders of withdrawals. This act was known as the 1952 Coal Act and the penalties were limited to civil penalties. It would take a couple more iterations of mine safety legislation for monetary and criminal penalties to be introduced (10). Up until 1966, mine safety legislation was directed primarily at underground coal mines and surface coal mines. Congress passed the Federal Metal and Nonmetallic Mine Safety Act of 1966, thus providing a set of standards for all mines to follow (1). The 1952 Coal Act was amended again to be the Federal Coal Mine Health and Safety Act of 1969. This amendment was the beginning of modern mine safety legislation (13). In 1973, Congress created what can be considered the first ‘version’ of the modern day MSHA (Mine Safety and Health Administration). The initial version was the Mining Enforcement and Safety Administrations or MESA. Congress created MESA to act as the enforcement agency, relieving the Bureau of Mines of that responsibility so they could focus on their initial purpose, the development of countries natural resources (14). As mining industry grew, mine safety and health became a greater concern and priority. More efforts were put in legislating the industry. The Federal Mine Safety and Health Act of 1977 provided the platform for today’s mine safety and health legislation. Under the Federal Mine Safety and Health Act of 1977, also known as the Mine Act, MSHA came into being (1)."

Jan 1, 2016

By Santosh Kumar Ray, DEBASHISH MISHRA, Niroj Kumar Mohalik, SOMU MANDAL, Jai Krishna Pandey, Asfar Mobin Khan

Coal is a low-cost and high-calorific-value fuel. The coal mining industry worldwide has been suffering from severe accidents due to coal dust explosion hazards since its inception. Statistically, it was observed that 12,489 fatalities had occurred in 104 reported mining accidents from coal dust explosions during 1900–2020. There are numerous methods for detection, prevention, and control of coal dust explosions in mines. The underground mining environment is unpredictable and has an array of variables. These undulating factors make it difficult to prevent or control the coal dust explosion hazard. However, coal mining is done aggressively throughout the world, especially in developing countries as coal is a major source of thermal energy used in power plants contributing to about 38% (IEA, (2019), World Energy Outlook, IEA, Paris https:// www. iea. org/ repor ts/ world- energy- outlo ok- 2019.) of world electricity. Worldwide, coal dust explosibility studies are carried out in experimental mines, laboratories, and simulations. The complexity, lack of proper infrastructure, and unavailability of laboratory equipment sometimes make it difficult to study coal dust explosibility. The authors have discussed in detail and proposed that the CFD modelling can be a viable option for studying and evaluating coal dust explosibility.

Jun 29, 2022

By Milton Gomez, Nico Sutmoller

Low-density cellular concrete (LDCC) was first introduced to the market in the early 1900s and since then has made continuous technological advances. There are two primary types of LDCC: permeable and non-permeable. Both types of cellular concrete offer advantages in different types of geotechnical engineering applications. Because of its unique characteristics of low density, high compressive strength, and high fluidity during placement, LDCC offers an effective solution for a wide variety of engineering applications, and in many cases provides a more cost-effective, labor saving alternative to traditional fill materials. This paper will review the history, characteristics, and technological advances of LDCC, highlighting multiple real-world case studies that showcase the high-performance capabilities of both permeable and non-permeable LDCC.

Dec 1, 2022

By C. K. Blankenship

The competitive forces now driving the electric utility industry and the constraints of regulation at all levels are changing the way we will all do business now and into the next century. Utilities are using every technological tool at their disposal to find optimum solutions to challenges in every aspect of operations. In fuel planning and procurement, these tools include models that predict which dispatch line-up will comply with environmental regulations at minimum cost. This paper presents how those tools are being used for Duquesne Light Company.

Jan 1, 1995

By DEVY DYSON, Brian Hart, JOHN LANGHANS, Stamen Dimov, STEVE YOPPS

A recent Nevada Gold Mines research program focused on pressure oxidation pre-treatment of a Carlin-type double refractory ore from the Turquoise Ridge Mine. The research team found that both arsenian pyrite and carbonaceous matter were highly oxidized within an hour at 300 °C using a bench-top autoclave reactor and that the gold recovery from the residues after cyanide/carbon-in-leach approached the technical limit set by the amount of gold encapsulated by silicate minerals. Although the 60-min pre-treatment at 300 °C yields robust performance when treating a whole ore, copper additives can catalyze the oxidation rate of carbonaceous matter and reduce the residence time needed at elevated temperature. Certain gangue minerals are susceptible to dissolution in acidic solutions at 300 °C, and this may cause poor gold recovery. This recovery challenge is mitigated by keeping free acid in the discharge solution below a key threshold.

Jun 21, 2022

By Peter Riba

Up until ten years ago the industry had arrived at a relatively conventional, and consistent design of coke ovens. Through the years the designers and builders were not being heavily taxed to come up with revolutionary new designs. However, the stimulus for design change was ever present. These stimuli for change are quite important and they are the driving force which produce improvements. The most obvious stimulus to change a design is commercial. To "build a better mouse trap and the world will beat a path to your door" is the well used cliche which best befits this philosophy. As in all businesses, coke oven designs require that all of the considerations, which affect the cost or the desirability of the design, be optimized. One way to increase the desirability of the particular design, 1s to make the design in- expensive to operate. Or, put another way, to increase production for the same operating cost

Jan 1, 1980

By Edwin K. Maughan

The Rocky Mountain region contains part of the paleocontinental shelf that lay in Arizona and New Mexico through Utah, Colorado, and Wyoming into Montana and North Dakota. The shelf was bounded by the northeast-southwest-trending Transcontinental arch and the Cordilleran miogeocline in late Paleozoic and early Mesozoic time. Major tectonic features that affected middle Phanerozoic sediments on the shelf were the Big Snowy trough and Williston basin in the north and the ancestral Rocky Mountains in the central part of the region. The Zuni uplift and similar positive areas occurred along the axis of the Transcontinental arch in the southern part. The late Paleozoic and early Mesozoic sedimentary rocks record transgressive-regressive marine cycles in which the Cordilleran shelf and much of the adjacent craton were inundated by epeiric seas. Early in the Carboniferous, an epeiric sea covered most of the shelf. Greater topographic relief developed in Late Mississippian, was at a maximum in Middle Pennsylvanian, and then diminished through Permian and Triassic time. The development in the Pennsylvanian Period of horsts and grabens along northwest- trending faults on the northwest flank of the Transcontinental arch resulted in the ancestral Rocky Mountain system. The eastern part of the region was emergent by Middle Triassic, and the emergence lasted until Middle Jurassic, owing to uplift along the Transcontinental arch. During the early part of the Mesozoic, the sediments were dominantly terrigenous and were deposited mostly in shallow littoral marine environments shifting to continental. Most middle Phanerozoic structural elements within the area of the shelf are characterized by lineaments that have either an east-northeast or a conjugate north-northwest trend. The east-northeast lineaments closely parallel the northeast trend of the continental slope (miogeocline) in Nevada to southern Idaho. The conjugate set closely parallels the northwesterly continuation of the miogeocline north of an approximately right- angle bend in south-central Idaho. The northeasterly trending Transcontinental arch and the northwest-trending margin of the Canadian Shield are parallel structural elements with the north- east and northwest trends of the miogeocline. The rectangular lineament pattern on the shelf suggests a system of rectilinear fractures within the underlying Precambrian crystalline basement rocks that moved several times in the Phanerozoic in response to external forces applied against the continental crust. Movement of these blocks influenced erosion, deposition, and lithofacies of the sediments in middle Phanerozoic time. Zones of crustal weakness, represented by the lineaments bounding these blocks, probably were influential in localizing sedimentary mineral accumulations and petroleum deposits, as well as later igneous intrusions, volcanism, and emplacement of hydrothermal ores. Igneous activity in this region was rare during the middle Phanerozoic, but these conjugate fractures seem to have been avenues for later passage of hydrothermal solutions responsible for ore emplacement.

Jan 1, 2013

By H. Yen, D. E. Walsh, H. K. Lin

"Comminution circuits are widely used in nonferrous and precious metals milling. Steel crushers, grinding mills and grinding media are typically used in comminution circuits. Comminution circuit wear products, in the form of metallic iron (steel) fines, are unavoidably produced and report to undersize products in the classification circuit, i.e., flotation or leach feed, while tramp grinding steel (TGS) reports to classification oversize products and returns to the grinding mill, building up in the circulating load. In laboratory studies, TGS reduced grinding efficiency significantly, the impact being dependent upon the size of the TGS present in the mill. Because iron fines adsorb flotation reagents effectively, iron fines increase reagent consumption and reduce flotation recovery. Iron fines are also capable of reducing gold recovery in cyanidation circuits via a cementation reaction. When using filtered gold solution from the cyanidation circuit of an Alaskan gold mine, the gold concentration in solution was reduced by 0.2 to 2.6% over various reaction periods when iron fines were present in the solution.IntroductionComminution circuits are widely used in copper, lead, zinc, nickel, cobalt, molybdenum and precious metal mills. Flotation and leaching processes are usually preceded by comminution (crushing and grinding) circuits in order to liberate valuable minerals for effective separation, concentration or dissolution by the subsequent flotation or leaching processes.Steel crushers, grinding mills and grinding media are typically used in comminution circuits. Comminution circuit wear products, in the form of metallic iron (steel) powder, are unavoidably produced and report to undersize products in the classification circuit (flotation or leach feed), while tramp grinding steel (TGS) reports to oversize productions during classification and returns to the grinding mill, building up in the circulating load. Variables affecting the amount of metallic iron powder and TGS produced in a comminution circuit include ore hardness, grinding mill operating conditions, comminution circuit design and the metallurgy of the steel used for manufacturing crusher liners, mill liners and grinding media. As one example, a comminution circuit product of 80% passing 200 mesh at the Pogo Mine, AK is estimated to contain approximately 2 kg/t of metallic iron. A finer grind will generally produce a comminution circuit product with higher metallic iron fines content."

Jan 1, 2015

By Ali Soofastaei

Mining operations are increasingly data-rich yet decisionconstrained. Fragmented systems, variability in geology and operations, and sustainability obligations create multiobjective trade-offs that classic analytics cannot reconcile at operational tempo. This paper proposes an end-to-end framework that fuses digital transformation practices (governed data platform, semantic layer, feature store, and MLOps) with generative AI (retrieval-augmented generation, tool-use, and agentic workflows) and decision intelligence (simulation/digital twins and multi-objective optimization). We formalize sustainability-aware objectives, define a practical stack and governance controls, and demonstrate how an AI “decision copilot” can surface options, quantify trade-offs, and document rationale. Two figures illustrate a production-grade architecture and a Pareto frontier for cost–emissions trade-offs; two tables operationalize decision-domain mapping and a transformation maturity rubric. The approach is product- and company-agnostic.

Feb 22, 2026

By C. K. Man

Coal dust explosions in underground coal mines are prevented by generous application of rock dust (usually limestone). If an explosion should occur, the rock dust disperses, mixes with the coal dust and prevents flame propagation by acting as a thermal inhibitor or heat sink. To investigate this process in more detail, a number of explosion experiments using various coal dust and limestone rock dust mixes have been carried out at the Lake Lynn Experimental Mine (LLEM). These were conducted in a single entry of about 1600 ft (488m) in length and initiated with a methane gas explosion. A consistent set of post-explosion floor dust samples were taken along the entry after each test. These dust samples have been analyzed in the laboratory using thermogravimetric analysis (TGA) and solubility to determine how the limestone rock dust behaved during the coal dust / rock dust explosions. The preliminary results are reported in this paper and indicate that the chemistry of limestone plays an important role in its capacity to inhibit coal dust explosions. The results also show that it may be possible to estimate the intensity of the explosion using these conventional methods of analysis. Disclaimer: The findings and conclusions in this report have not been formally disseminated by the National Institute for Occupational Safety and Health and should not be construed to represent any agency determination or policy.

Jan 1, 2009