Search Documents

By Dong Yang, Jicai Han, Xiaoshuang Guo, Tichang Sun, Zhengyao Li

Straw charcoal was used as a novel reductant in the co-reduction roasting of laterite ore and red mud. The influence of the reductant dosages, co-reduction temperature, and co-reduction time were investigated. Results showed that a powdered ferronickel product of 1.81wt.% nickel and 81.40wt.% iron was obtained under straw charcoal dosage of 15wt.% and roasted at 1250 °C for 80 min. The corresponding recovery of nickel and total iron were 97.21wt.% and 98.87wt.%, respectively. The performance of straw charcoal was also compared to that by the conventional coke reductant. Results showed that ferronickel particles using straw charcoal were larger in size than coke, mainly due to the lower S (0.14wt.%) and ash content (3.80wt.%), which could not hinder the agglomeration of the ferronickel grains, and lower melting point that producing liquid phase and promoting ferronickel particles growth. In addition, the gasification reactivity of straw charcoal is better than that of coke, which is beneficial to the iron oxide reduction and the recovery of iron. To conclude, straw charcoal is a promising reductant for the co-reduction of laterite ore and red mud in coal-deficient areas.

Aug 12, 2021

By A. Founie

The United States continues to be the world’s leading producer and consumer of diatomite. Production of diatomite in the United States during 2004 was estimated to be 635 kt (700,000 st). This was a 2-percent increase from 2003. The value of processed diatomite in the U.S. was about $164 million in 2004. Production was from six companies with 13 processing facilities in four states. Nevada and California were the principal producing states. They accounted for about78 percent of the U.S. production during 2004. U.S. diatomite exports were about 136 kt (150,000 st). Imports were negligible.

Jan 1, 2005

By A. Rai

"This paper provides an overview of the current use of auxiliary ventilation product and the challenges with limited air quantity in dead-end entry or working face. The PVC low frictional factor, low physical constraint and minimum leakage ventilation duct was development with ""made in US and used in US"". The PVC duct development covering operational and total cost of ownership with on-going success will be presented. This paper will discuss mine sites using new PVC vent duct underground and the results from operational and technical side making a difference. INTRODUCTION The Turquoise Ridge Joint Venture (TRJV) is located in northern central Nevada, and is situated within the Basin and Range province, near the northeast end of the Osgood Mountains (see Figure 1). The TRJV mine consists of typical Carlin type- gold mineralization characterized by low strength rock of altered limestone’s, siltstones, and mudstones. The weak nature of the ground facilitates the underhand cut and fill mining methods [3].Mining Method; Underhand cut and fill : The mine uses underhand cut and fill method which has 12’x12’ top cuts and several different size undercuts. The ore body is accessed off of a secondary development heading, utilizing a heading with a cross section of 14W x 14H or 15W x 16H configuration. In the wider and more massive zones, two headings in a production panel may be worked at any one time. Drift round lengths are determined by the type of drilling machine being used. An example of a typical topcut and associated undercut layout is shown in Figure 2. SECONDARY / AUXILIARY VENTILATION IN UNUNDERGROUND METAL MINES The auxiliary ventilation system provides the required air volumes at the face of dead-end developments and production workings, which in many cases may be considered as the primary method of assuring that the air quantity and quality standards in these working areas are satisfied. The Auxiliary fans and ducting systems are usually the primary means of delivering the required air volumes to the face of dead-end developments and production workings. Both centrifugal and axial-flow fans are used in underground auxiliary ventilation systems, usually electric powered. The internally direct driven axial-flow fans tend to be more popular because of their compactness and adaptability to staging. The most commonly used materials for ridged tubing are coated steel, alloyed steel, fiberglass and resin. Flexible (collapsible) ventilation tubing is also used and is usually made from neoprene-coated or nylon material. To add stiffness and reduce collapsibility these fabric ducts can be formed over a steel spring frame. A very important factor in the design of an auxiliary ventilation system is to minimize leakage and reduce the frictional pressure losses along the auxiliary ducting systems by minimizing their friction factors (K)."

Jan 1, 2015

By D. P. Tao, J. G. Groppo, R. Killmeyer, W. W. Wen, B. K. Parekh

Economical dewatering of ultra-fine (minus 74 m) clean coal slurry produced in column flotation to a 20 percent or lower moisture level will be an important step in successful implementation of the advanced fine coal cleaning processes. The main objective of the present study was to evaluate efficiency and effectiveness of three dewatering techniques, namely, hyperbaric, vacuum and screen bowl centrifuge, in dewatering of ultra-fine (D50 ~ 25 m) clean coal slurry produced by the `Ken-Flote' columns operating at the Powell Mountain Coal Company, St. Charles, Virginia. he hyperbaric filter using 3 bar pressure and 165o cake formation angle, provided a filter cake with 23.6percent moisture with a throughput of 800 Kg/m2-h and air consumption of 868 Nm3/t (460 scfm/t). The vacuum filter with 30 percent submergence provided a filter cake with 27.8 percent moisture with a throughput of 122 Kg/m2-h. The screen bowl centrifuge provided a dewatered product containing 32.9 percent moisture at a feed rate of 450 Kg/hr, however, the solids capture was only65 percent. Addition of 1 Kg/t of a cationic surfactant provided filter cakes with 19.1 percent, 23percent, and 34 percent moisture using hyperbaric, vacuum, and centrifuge, respectively. Similarly, addition of 0.5 Kg/ton of copper chloride lowered filter cake moisture to 20.7 percent and 24.8percent, using hyperbaric and vacuum. With the centrifuge no improvement in filter cake moisture was noted. However, use of 80 Kg/ton of `orimulsion' in the centrifuge provided dewatered product containing 26 percent moisture, and the solids capture increased from 65 to 95 percent. The dewatered product appeared dry and was easily handleable.

Jan 1, 1999

By Nikhil Dhawan, Veeranjaneyulu Rayapudi

This study investigates upgrading of low-grade banded hematite quartzite iron ore (Fe ~31%). Conventional beneficiation was found to be futile. The susceptibility of iron phases to microwave exposure and their selective absorption assists in the liberation of iron values. Microwave exposure of coarse particles at 540 W for 10 min yielded a concentrate with Fe 56.30% and recovery of 50.68%. Conventional carbothermic reduction at 500 °C, 60 min and 9% charcoal yielded a concentrate with Fe 57.6% and iron recovery of 68%. The presence of sufficiently bonded silica leads to an easy formation of a fayalite phase. The microwave reduction design yielded FeG of 57.6%, FeR of 47% and a yield of 24% at an optimal condition of 540 W, 8 min and 6% charcoal. It was found that a small fraction of microwave-irradiated ore-charcoal mixture melted rapidly, and pure ferrite balls were observed within 8 min. An optical micrograph of a ferrite ball reveals the retained austenite and martensite phase.

By H. D. Van Veldhuizen

The Multilateral Investment Guarantee Agency(MIGA) is part of the World Bank Group, and has as its mission the facilitation of foreign direct investment by providing political risk insurance (guarantees) to foreign investors and lenders. As a development institution, MIGA is required to ensure that the projects that it insures will bring development benefits to the host country. Demonstration of this includes review and analysis of the environmental and social soundness of a prospective investment. Environmental guidelines and policies developed by the World Bank Group are important components both in analyzing the environmental and social soundness of a prospective investment and in risk management. MIGA has recently formalized and adopted environmental assessment and disclosure policies. The approach taken by MIGA to environmental review of investments and implementation of these policies is described in this paper.

Jan 1, 2000

By David Atkin

This paper presents methods and results of environmental planning conducted for a proposed coal and iron ore transshipment terminal which would be located on reclaimed land west of Lisbon, Portugal. Oceanographic, navigational, marine, structural, material handling, and financial studies of the terminal were conducted along with the environmental analyses. However, because of the proximity of the terminal to heavily used recreational resources, residential areas, and biologically valuable habitat, anticipating and reducing the environmental effects of the terminal to minimum levels was a very important part of the overall project. The results of the study indicate that even the impacts associated with worst-case conditions would be acceptable because of appropriate pollution control measures and planning.

Jan 1, 1983

By J. Richard Kyle

The Pb-Zn ore bodies in the Pine Point district are localized in paleo-solution structures that developed as the result of post-middle Givetian subaerial exposure of the carbonate barrier complex. Sulfides are concentrated in transgressive pale-solution structures that acted as natural bypasses between aquifers and loci for mixing of fluids of different character, one of which contained metals and the other reduced sulfur. Complex ore textures indicate rapid early sulfide precipitation followed by slower sulfide growth. Evidence for both sulfide-carbonate equilibrium and disequilibrium conditions suggest fluctuations in ore fluid composition. District and ore body metal distribution patterns may reflect the nature and movement of mineralizing fluids.

Jan 1, 1979

By Paul D. Tomlingson

World class performance is the ultimate objective of many maintenance organizations. It marks the organization as a leader in its industry and sets it apart as the ultimate achiever. But what is a “world class” standard and how can it be achieved? Is there a yardstick by which an industrial organization can measure the relative performance of its maintenance activity and compare it with performance levels that universally identify “world class” status? Are there financial formulas, achievements, evaluation techniques or indices that provide this yardstick?

Jan 1, 2006

By Donald Towse

Geothermal heat might become an important fuel for several reasons: (1) To substitute for other scarce and critical fuels. (2) Because it may be less costly to the user than alternate fuels. (3) Because its production may be more profitable than production of other fuels. (4) Or for a number of other more or less non-economic reasons such as convenience or because of less environmental impact. In competition with conventional and other non-conventional fuels, geothermal heat must score well on one or more of those points. This study first considers projections of energy needs in several United States economic sectors and the technical possibility of geothermal heat substituting for other fuels in those sectors. Then, reported and projected costs of energy from geothermal heat are compared with costs of other fuels to show the relative costs of fuels in several economic sectors. Relative costs are reported from a sample of real and hypothetical geothermal projects. The actual cost of energy will vary with each application and the particular circumstances of each geographic location.

Jan 1, 1975

The National Mining Association’s (NMA)MINExpo International ’96 is shaping up to be the organization’s largest. About 30,000 mining industry business and technical professionals are expected to descend on Las Vegas, NV Sept. 9-12 to take part in the 25 technical sessions and visit the more than 900 exhibitors who will be showing off their products and services. MINExpo will be the largest mining equipment and services exposition in the United States this year. Exhibits at MINExpo will fill the Las Vegas Convention Center, parking lots and part of the Hilton Center, located next door to the convention center. NMA estimates that this year’s show will cover more than 46,450m2 (500,000 sq ft) of exhibit space. Some of the exhibits on display will include haultrucks, hydraulic shovels and excavators, conveyors, continuous miners and tunneling machines. In addition, an array of computer equipment and software will be demonstrated. A new feature this year will be a helicopter pavilion, located in the Hilton Center. Helicopters and fixed-wing aircraft have become indispensable to many remote mining operations. NMA said that at least one full-size helicopter will be on display.

Jan 1, 1996

By Mirko Martini, Marcelo Benaglia, Andrea Codalli

Riachuelo Lot 3 forms part of a sanitation programme being implemented in Argentina to relieve the Riachuelo river basin from its current contamination. The programme, by far the most important in its kind in the country during the last decades, will expand the sewage capacity of Buenos Aires and will benefit an area of 4.3 millions inhabitants by intercepting a number of waste water discharges and conveying them to a new treatment plant prior to final discharge into the Rio de la Plata. The project foresees amongst other works the construction of an onshore 48 m deep shaft at the outlet of the treatment plant plus a 4,3 m inner diameter outfall tunnel of 12 km length. The last 1.5 km of the alignment is fitted with 34 vertical risers jacked from inside the tunnel to allow the discharge and dilution of the treated effluent into the Rio de la Plata. This paper describes the peculiarities and challenges, both in terms of design and in terms of construction, of the outfall tunnel, which was entirely bored under the Rio de la Plata using a 5.2 m cut diameter Tunnel Boring Machine (TBM). On one hand, the tunnel segmental lining was designed to work in tension during the system flow rate peaks while on the other the tunnel excavation faced a variety of complex conditions, such as crossing water bearing permeable soft ground formations and advancing at face pressures in excess of 3,5 bars for the entire route.

Jun 13, 2021

By John A. Cherry

Groundwater monitoring conducted at an acidic uranium-tailings impoundment in Wyoming and at one in Ontario indicate that at these unlined impoundments situated on unconfined sand aquifers, there exist well-developed plumes of contaminated groundwater. In the literature similar results are reported for three other unconfined aquifers at mill sites in Wyoming. The plumes extend for distances of several hundred to a few thousand metres from the impoundments. They have a zone of low pH beneath and adjacent to the impoundments and a larger zone of near-neutral pH that extends to the outer limits of the plume. The low-pH zones are generally small compared to the neutral-pH zones because the advance rate of the fronts of acidic tailings-derived water is slower than the average velocity of groundwater which controls the advance of the high pH zone. The retardation of the acid fronts is a result of geochemical reactions that cause hydrogen-ion consumption in a slowly-advancing neutralization zone. Within each of the plumes, the low-pH zone has high concentrations of transition metals, heavy metals and radionuclides. In the neutral-pH zones all of the metals and radionuclides occur at significantly lower concentrations and are generally at levels much below those specified in national drinking water standards. An exception at two of the Wyoming sites is uranium, which exists at levels close to the drinking water limit. A second exception is ferrous iron at the Ontario site, which occurs at high concentrations throughout most of the plume. The carbonate alkalinity at this site is much lower than at the Wyoming sites. The field data indicate that even in very permeable aquifers with a low content of silt and clay, there is normally a considerable capacity for acid-front retardation. To take advantage of this capacity to control contaminant movement in the design, operation and decommissioning of tailings impoundments, it is necessary to be able to predict the rate of acid-front movement. This predictive task has two primary components. The first is to identify the important flow paths from the tailings through the groundwater system and the second is to determine the degree of acid-front retardation that will occur as the tailings-derived water moves along these flow paths. Relative to these two tasks determination of the effects of hydrodynamic dispersion is generally of lesser importance and simple approximations that do not involve field or laboratory tests are probably adequate. In order to effectively apply the acid neutralization concept to the prediction of subsurface contaminant migration at uranium-mill tailings, improved representations of hydrogeochemical behavior of iron and aluminum in the neutralization zone and of the consumption of hydrogen ions through reactions with carbonate and aluminum-silicate minerals are required. Along with the hydrogen ions contained in the tailings water the ferrous iron represents a large potential source of acid but the extent to which ferrous iron converts to ferric iron to produce acid is problematic. Detailed hydrogeochemical evaluation of existing contaminant plumes and the performance of laboratory experiments under appropriate redox conditions ore prerequisites for the improvement of predictive models. However, the existing field and laboratory data provide a basis for preliminary predictions of contaminant migration from acidic uranium tailings impoundments.

Jan 1, 1982

By Christopher Mark

Sixty years ago, underground coal mining was the most hazardous job in the United States. Roof falls were a big part of the problem. They killed about 100 miners every year, more than all other causes put together. Fast forward half a century to 2016, which is the first year ever with zero roof fall fatalities. Just three miners were killed by roof falls during the following 6 years. How was this historic goal achieved? This paper starts with a modern analysis of the causes of the roof fall fatalities in 1968. Then it follows the reductions over time by category, using snapshots of the fatalities occurring in subsequent decades. Along the way, it evaluates the influence of the regulatory environment, changing mining methods, and better ground control technology. The paper shows that in 1968, more than half of roof fall fatalities at large mines were attributable to an inadequate safety culture. The immediate effect of the 1969 Coal Mine Health and Safety Act was to reduce the riskiest activities, like needlessly going under unsupported roof. Other hazards, like large roof falls, required technological developments before they were brought under control. Roof control plans, which the U.S. Bureau of Mines had been advocating since the 1920s, played a significant role throughout the process.

Jul 1, 2023

By Manuel Gomez

This report presents prediction equations for eleven factors indicative of metallurgical coal quality which have been developed from data obtainable during exploration. Five coke strength parameters and six carbonization product yields have been predicted for coking coals having volatile matter contents in the range 16.3 to 42.1 percent, dry basis. The prediction models developed contain information from the proximate and ultimate analyses, the size consist, and the petrographic composition of coking coals carbonized in BM-AGA retorts at 800°, 900°, and 1,000°C. The equations reported have been evaluated with independent data derived from the 900°C carbonization of 33 binary blends. Present results show that metallurgical coal quality can be predicted ahead of mining. Capability to forecast coal quality is useful in mine planning and should provide basic information for optimization of blending and crushing techniques, leading to the production of uniform coke.

Jan 1, 1968

By Nord L. Gale

Lead, zinc, copper, silver, cadmium and many other heavy metals which are potentially hazardous if released into the environment in wastewater discharges have been of considerable concern to governmental agencies, industry and the general public. In response to this concern, an interdisciplinary research team at the University of Missouri has been funded by the National Science Foundation-RANN program to study trace contaminants associated with the production of lead for the past eight years. Seven modern mines in close proximity to two lead smelters in the forested Ozarks of Southeast Missouri are the largest source of lead in the world and in 1976 alone produced 504,095 short tons of lead, 82% of the United States total production. This new and rapid industrial development in a sparsely populated. rural forest region has offered a unique opportunity for studying the impact of trace metals and for developing improved techniques to control detrimental effects. Research on the wastewater discharges and two methods of biological and recycle control are discussed in this paper. Although the two mine-mill complexes investigated in this study have many similarities, the differences between the two are substantive and warrant separate examination.

Jan 1, 1977

By A. W. Czarnowsky

More than ever before, mining projects are besieged from growing regulatory, political, public, and special interest group pressure. Administrative and legal appeals to permits and environmental documents can delay project start-up and add tremendous cost to mineral development. Some mining projects have been canceled given undue external constraints. Successful managers must learn to cope with these constraints. This paper will discuss controversy and present a number of environmental management tips to minimize the potentials for delay and to lessen the impacts from government and anti-mining pressures.

Jan 1, 2001

By A. J. Richins, M. G. Nelson, R. Dunne

From the inception of flotation in the late 1800s, coarse particle recovery has been a challenge to practitioners. By the early 1900s, flotation processes included oil flotation, skin flotation, agglomeration flotation, and froth flotation, and for each there was a proliferation of flotation equipment. Ensuring good coarse particle recovery included desliming of the feed and proper conditioning were required. Froth flotation was at first used mainly to treat finer materials from grinding circuits. The maximum size for coarse particles was from 3.18 to 4.78 mm. In froth flotation, large particles with high specific gravity tend not to be recovered. Coal and minerals of low specific gravity and flaky minerals such as graphite, mica, and talc can be floated in larger sizes. In the early 1960s, the phosphate industry began using column cells to recover coarse particle by froth flotation, but early columns suffered from poor bubble generation and sanding at the flat base of the column. Recently, improved coarse particle recovery has been the object of new cell designs—the Eriez HydroFloat™, the Jord NovaCell™, the FLS coarseAir™ cell, and the Cidra P29 integrated system. The paper will follow the development of coarse particle flotation with a focus on the development, laboratory assessment, and operation of the new flotation equipment and technology designed to recover coarse particles.

Feb 22, 2026

By G. J. Olson

This paper describes the microbiology basics underlying heap and tank biooxidation of metal sulfide ores and concentrates. The primary organisms are identified and described along with the reactions they catalyze and their growth requirements. Also described is the interaction between ore leaching bacteria and the leaching environment in terms of solution chemistry, temperature, and mineral precipitation. Specific factors and agents that stimulate or inhibit growth and activity of ore bioleaching will be identified. Some of these factors are organism-specific and others are generic for microorganisms that grow under acidic conditions. Current knowledge of the limits of bioleaching in terms of dissolved ions in leach solutions, pH, and temperature will be summarized.

Jan 1, 2003

By Neel Gupta, Brijes Mishra

Coal mining activity disturbs the natural equilibrium of in situ stress state such that the induced stresses deform the surrounding rock mass. Although the installation of roof supports typically prevents rock deformation, rock mass failure may still occur in bolted roof. The erratic failure of rock mass after few days to months and years of excavation is the result of time-dependent deformation of roof rock under constant surrounding stresses. In the current research, the triaxial laboratory creep experiments proved that Marcellus shale exhibits time-dependent deformation under constant stress that was smaller than the failure strength. However, unlike conventional experimental results, the time-dependent deformation did not depend on the level of constant stress. The often-neglected initial state of specimens and intrinsic heterogeneity highly influenced the time-dependent failure of Marcellus shale.

Jul 27, 2021