Search Documents

By R. D. Peterson

As underground mine operations expand, the ventilation systems supporting them become complex. Complexity increases with periodic ventilation changes. New diagonal connections require a rebalance of resistance to maintain airflow in affected splits in the system. Incidents of mine fires and explosions have occurred in U.S. coal mines when diagonal connections resulting from ventilation changes have resulted in changing airflow directions. MSHA regulations prohibit the reversal of airflow and poor ventilation practice in general, but regulations cannot stipulate or recommend proactive preventative measures because every situation is different. This paper discusses the phenomenon of diagonal branches and recommends practical precautionary measures that can be taken to prevent airflow reversal in planned ventilation changes.

Jan 1, 2012

By Delon Hampton, Francis K. Mensah-Dwumah

INTRODUCTION The state-of-the art in the area of soil-structure interaction is not sufficiently developed that one can accurately predict the earth load distribution on buried structures. This lack of knowledge has led to the use of high factors of safety in their design and conservative assumptions for the loading diagrams. As a step towards the improvement of the design methodology for buried structures, it is important to be able to apply new analytical techniques and monitor the performance data obtained on full-size buried structures. The performance data should preferably include: 1) the actual stress distribution on the buried structure, 2) stress distribution in the buried structure and surrounding soil media, 3) vertical and lateral movements in the soil adjacent to the buried structure, and 4) deflection of the buried structure. Brown (1967), Davis (1972), Krizek, et al (1974), Krizek and MacQuade (1978), and some few others have compared the performance of full-size culverts with finite element results. Despite all these efforts, a complete understanding of the soil-structure interaction problem has not yet been fully achieved. In an effort to make improvements in the existing design procedures for buried structures constructed in an open-cut, the Department of Environmental Services (DES), Washington, D.C., in conjunction with Howard University, undertook a detailed study of Section II of the Capitol Hill Relief Sewer (CHRS). Inclinometers were used to measure lateral movements of the excavation wall and the total normal interface stresses acting on the concrete sewer were obtained using glotzl total pressure cells. This paper describes the results of the field instrumentation program for acquisition of data, their comparison with the design assumptions, and the results of a series of post-construction finite element analyses of the CHRS project.

Jan 1, 1979

By M. J. Sapko

From 2001 to 2007, the Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) conducted studies to develop alternative methodologies to full-scale explosion testing for deter-mining the ultimate strength of mine seals. As a result, the PRL developed and proposes an alternative seal-strength evaluation method based on a hydrostatic pressure-loading concept. The researchers suggest pressure loading a seal using water to twice the expected dynamic design load. The hydrostatic chamber test offers a means of validating seal designs, establishing appropriate resistance functions and determining the ultimate strength of seals through testing to failure. This article contrasts the full-scale explosion and hydrostatic testing of mine seals using a simple dynamic system model and principles.

Jan 1, 2008

By John E. Newby

Washington?s King County is constructing a new regional wastewater treatment facility, called Brightwater, in response to growth in the greater Seattle region. Planning conducted in the late 1950s identified the need for two regional treatment facilities. Constructed in the 1960s, these plants have served the region well. However, an eventual need for a third facility was also recognized. The Brightwater project implements the final phases of the long-term plan. The project includes a new treatment plant and an extensive conveyance system. When completed in 2010, the Brightwater facilities will treat sanitary sewer flows from growing populations living in northern King County and southern Snohomish County. The new system will fulfill commitments to provide wastewater services to local jurisdictions and sewer service providers in the King County Service Area. It will also provide more flexibility in the operation of the King County regional wastewater system. The Brightwater wastewater treatment plant will provide secondary treatment capacity using membrane bioractor technology in 2010 for 36 million gallons per day (mgd), with anticipated expansion in 2040 to 54 mgd, using membrane bioreactor technology. These capacities are for average wet-weather flows. The plant will also accommodate peak hourly flows of 130 mgd by 2010 and 170 mgd by 2040. The Brightwater Conveyance System consists of more than 8.1 km (13 miles) of tunneled influent and effluent conveyance lines, five tunnel portals/shafts, microtunneled influent and outfall connec-

Jan 1, 2007

By Robert J. Timko, Charles D. Taylor, Edward D. Thimons, Tom Mal

A test system was developed for measuring airflow in the National Institute for Occupational Safety and Health (NIOSH) ventilation gallery using a three-axis ultrasonic anemometer. The gallery was used to simulate face airflow conditions in underground mines having a blowing curtain. Airflow data collected at multiple sampling locations between the face and the end of the curtain were used to draw airflow profiles for different curtain setback distances, intake flow quantities and entry widths. In addition, methane was released at the face, measured at the sampling locations, and displayed as methane distribution in the area between the curtain and the face. Entry geometry had a significant effect on airflow patterns, and the flow patterns affected the distribution of methane in the entry. Flow measured at and parallel to the face was a good predictor of methane dilution and removal within two feet of the face.

Jan 1, 2005

The stability of surfactant-free foam films was studied using the thin film pressure balance (TFPB) technique. In pure water, it was not possible to produce foam films due to weak film elasticity and strong hydrophobic force. In the presence of NaCl, however, the hydrophobic force was sufficiently dampened to allow metastable films to form. At 10-5 M NaCl, the equilibrium film thickness reached a maximum of approximately 130 nm at pH 6.0-7.3. The thinner films obtained on either side of this pH range was due to the increased ionic strengths associated with the HCl and NaOH additions for pH control.

Jan 1, 2009

By M. Z. A. Bakar

To investigate the differences in the radial drag pick cutting performance in dry and saturated sandstone, a suite of linear rock cutting test was performed using linear rock cutting machine (LRCM). Experimental results of 50 data passes, incorporating 350 data cuts were used to compute cutting, normal and side forces required for determination of other performance related parameters. Although the forces required to cut the dry and saturated rock were in congruence for most of the spacing and depths of cut combinations; but the overall averaged cutting and normal forces for saturated rock cutting were found to be 9.9% and 9.4% respectively higher than the dry rock cutting. The increase in the overall averaged forces was attributed to strength variability of one of the saturated block affecting the overall forces. The side forces experienced a negligible drop in saturated rock cutting. An increase of 28% and 9% in the actual and nominal specific energy values respectively was also recorded when cutting saturated rock as compared to the dry rock cutting. The increase in saturated rock specific energy is attributed to production of large amount of fines and few large sized chips directly contributing towards increase in specific energy. The optimum s/d ratio for dry rock tests was found to lie between 6 and 8 whereas for saturated rock cuts this value lied between 5 and 9.

Jan 1, 2012

By Carlos Henrique Turolla Maia, Ulrich Maidl, Marc Comulada, Julio Claudio Di Dio Pierri

"Pure sands are typically the domain of slurry shields due to their high permeability and their granular characteristics. However, the Earth Pressure Balanced (EPB) shield machine technology has advanced in recent years with improved conditioning agents and shield machines that are equipped with slurry injection facilities and alternative mucking methods. These new so-called hybrid EPB machines have steadily increased the range of application of the EPB technology. The contribution discusses the capacities and operational features of hybrid EPB vs. slurry shield technology in pure sands. At the example of the Metro Line 4 in Rio de Janeiro (Brazil), the contribution shows that hybrid EPB tunneling in pure sands is possible and it is compared with a state-of-the-art slurry shield project as the KASIG project in Karlsruhe (Germany). Furthermore, the control of the support pressure by means of foam conditioning and slurry injection in conjunction with a close, real-time monitoring of machine parameters is discussed. INTRODUCTION Slurry shield and EPB technologies have both undergone significant developments in recent years, leading to the use of parts of one technology in the other and even to completely hybrid systems. Also the ranges of application (see recommendations by DAUB (DAUB 2010)) of both technologies have been shifted far beyond their original limits and are largely overlapping by now. Nevertheless, the basic principles of face support remain unchanged. Exploiting the possibilities of process data analysis (Maidl 2014), the interactions between the ground and the shield machine are a matter of research and have been intensely investigated. PRINCIPLES AND CALCULATION OF FACE SUPPORT PRESSURE Figure 1 shows the principles of two approaches for the determination of required support pressures: kinematic methods and numerical methods. Kinematic methods that are employed for the assessment of face stability only consider the situation in front of the TBM. The required face support force is determined by means of an assumed failure wedge that would form in ultimate limit state. Based on the ground properties, the vertical surcharge and the self-weight is transformed into a horizontal force along a virtual sliding surface. This horizontal force is to be balanced by the face support. The calculation results are amended by respective partial safety factors for water and earth pressure and the method-specific support pressure fluctuations are added."

Jan 1, 2016

By TOMI GIORGIO DE, Ricardo Tichauer

Mineral exploration is a key factor for success in the mining industry. However, exploration best practices are often ignored in small-scale mining. This works presents the Tichauer-DeTomi Matrix, a methodology that measures the level of compliance of exploration programs in small-scale mining with the industry best practices. The matrix has been applied to three projects in Brazil: an artisanal gold mine in the state of Pará, a small-scale manganese project in the state of Bahia, and a small-scale manganese project in the state of São Paulo. The application of the matrix resulted in indexes that represent the level of maturity of the exploration program in each project and indicate priority actions for reduction of the geological uncertainty. Therefore, the Tichauer-DeTomi Matrix has shown potential to be a useful tool for assessment of geological uncertainty in small-scale mining. As a risk indicator, it may contribute to promoting investment in small-scale mining and development for communities that depend on this activity around the world.

By M. Pérez-Tello

A mathematical model to represent the expansion and fragmentation of copper matte particles oxidized under flash converting conditions is presented. The model assumes that the particles are initially nonporous, have a constant mass prior to fragmentation and travel at a constant velocity throughout the reaction chamber. The model requires the specification of the following five parameters: the particle expansion rate, a fragmentation diameter factor, a fragmentation size distribution parameter and the fractions of the finest and the coarsest particles in the feed that undergo fragmentation. The model predictions show good agreement with the experimental data collected in a laboratory furnace over a wide range of experimental conditions. The evolution of the size distribution of the particles along the reactor length was computed, and the model parameters were correlated with the experimental operating variables. Model predictions indicate that particle residence time is an important factor in the generation of dust. The presence of two maxima in the particle density function may be attributed to turbulent conditions prevailing in the furnace, which cause particles to follow different trajectories within the furnace even if they are injected at the same location.

Jan 1, 2008

By J. Hunter, E. Jackson

This paper describes work done by Placer Dome Technical Services Limited, a subsidiary of Barrick Gold, and Nautilus Minerals Inc. in support of the conceptual design of a subsea mining system. It describes an overall concept design plus specific studies into mechanical excavation at depth. The concept design includes one or more subsea excavators connected to a suction riser, which transports the cut material to a shipboard dewatering and offloading system. A multi-phase investigation was performed into the mechanical excavation of seafloor massive sulphides at depths of around 1600m. Rock samples were recovered and tested for rock properties and cutting behaviour. A small pick drum cutter was procured and tested on a representative concrete slab in a lab and tested again while submerged in a test tank. Finally the cutter was tested on a massive sulphide ore body at 1600m depth. The cutting performance results, e.g. pick forces and specific energies, should provide valuable input to the design of future full scale subsea mining systems.

Jan 1, 2007

By I. Yildirim

Water contact angles of talc powders were determined from the values of the heats of immersion measured using a flow microcalorimeter. The results were used to calculate the contact angles using a rigorous thermodynamic relation. In the present work, the calculation was carried out using the temperature coefficient of the contact angles determined experimentally using another method. The results obtained in the present work on several different talc samples are compared with those obtained using other methods.

Jan 1, 2001

By Phillip Crowson

The annual surveys of corporate exploration expenditures carried out by Metals Economics Group (MEG) show that estimated total spending rose to a record $13.2 billion in 2008 ($14.4 billion including expenditure on uranium exploration). This compares with the previous peak of $5.2 billion in 1997. MEG does not adjust its figures for the effects of inflation but recognizes that the substantial increase in budgets of recent years has not been reflected in a proportionate rise in actual activity on the ground (MEG, 2009). In recent years, costs were boosted by rising prices of fuel and other inputs, and acute shortages of qualified staff and drilling rigs. The inflation rate for exploration substantially exceeded increases in general price levels as measured by national indices. Just how much exploration costs in-creased, however, is probably not widely appreciated. Figure 1 compares the MEG estimates of total annual dollar spending in Australia, Canada and the United States combined with their drilling activity, measured in meters drilled, as reported by national agencies. These three countries accounted for 39 percent of MEG?s estimate of total spending on minerals exploration in 2007 and 40 percent in 2008. Expenditure is shown both in money terms, as reported by MEG, and adjusted to real terms, with the U.S. implicit gross domestic product (GDP) price deflator. The comparison is of index numbers based on 2000 as 100. Comparisons for the individual countries are shown in Fig. 2 to 4. National figures for drilling activity and expenditures cover some minerals like iron ore, coal and industrial minerals (29 percent of Australian spending in 2007 to 2008 and 10 percent of Canadian in 2008) that are not included in the MEG estimates of spending. Such exploration has risen more than the total since 1997 so that the index of drilling activity in the figure may be overstated for recent years on a like for like basis with the MEG data. MEG only includes spending on uranium exploration in recent years whereas the national agencies include it throughout. Figures 5 and 6 com-pare national and MEG estimates for Australia and Canada. No comparable figures are available for the United States. The national estimates have been converted to U.S. dollars at the appropriate annual average exchange rates, and the Australian annual totals have been summed from the published quarterly data. Not only is spending cyclical, but so are unit costs. Australian and Canadian data show that total exploration spending per meter drilled rose by 2.5 to 3 times between 2001 and 2008. These rises may partly reflect increasingly complex drilling methods, and an increased share of assaying and testing in total exploration costs. In Canada, however, diamond drilling accounted for a lower footage of the total in 2005-2007 than in the preceding few years, and spending on exploration, as opposed to deposit appraisal, made up a higher proportion of the total. Figure 7 compares index numbers of exploration spending per meter drilled in U.S. dollars for Australia and Canada. These figures raise a number of questions. First, is the relationship between total expenditure and meters drilled in the three countries for which data are available typical of the global experience? Secondly, has there been a significant change in the make-up of exploration spending in recent years? The Canadian data do not suggest that there has been, but is Canada typical? Has drilling become less important relative to other exploration techniques, or is it just as important as ever in confirming the existence of viable ore deposits?

Jan 1, 2009

By H. Do, R. Yoon

Mineral flotation is effective over a relatively narrow particle size range of approximately 10 to 100 µm. If the upper particle size limit can be increased, however, a run-of-mine ore may be coarse ground, and only the middlings are ground further to achieve required grades. This will result in significant energy savings and increased throughput. In this communication, methods of increasing the upper particle size limit will be discussed on the basis of a flotation model that can predict flotation from both hydrodynamic and surface chemical parameters. An example of increasing flotation recovery by control of a chemistry parameter is given.

Jan 1, 2007

By M. Javier

Mining is an industry of experimentation throughout human history. Recently, societies are giving a clear message about mining because many projects are being rejected around the world. These refusals are a generational reaction to the activity of mining. In practice, it generates the perception that mining is using the same methodology without attending to the gradual initiation of conflicts. This is in spite of the best engineering and technology of the time that are put in place at the presentation of those mining projects. Some of these rejected projects are geographically distant from each other, but the communities? rejection occurred during many cases under similar characteristics. This concern shows that the current model of mining projects needs to be replaced with a new one: A new Design, one within which the socio-environmental values of this millennium are inherent. This paper describes Mining Project 101 to help the industry to set the highest and cleanest standards for mining. It also presents its aspects to sustainability and nature, which provides the principles and procedures for designing, planning, and operating mining projects with sensitivity to nature. It offers methods of diagnostic, remediation, and extraction while at the same time preventing and preserving a physical, chemical, and biological equilibrium of nature. This emerging process will be a step up from having a mining industry unaccountable to the socio-environmental conflicts it perpetrates and will abandon the ?cosmetic? repair on the caducity of traditional models in today?s practice. In conclusion, we have the opportunity to change this model. KEYWORDS: Equilibrium in Nature, Geomímic, Deproduction, mine design.

Feb 27, 2013

By R. B. Crookston

This paper presents the status and mining method chosen by each of the active underground oil shale projects in the united States today. Potential improvements in equipment and methods on the near-term horizon are discussed. The problems and potentials that lie in the long-term future of oil shale mining are examined in light of the demands which must be met by this developing technology.

Jan 1, 1981

As ore deposits become finer grained the requirements for regrinding before cleaning or leaching have increased substantially. Despite this increasing need, there is no standard test to predict grinding energy requirement below 70 microns. The standard Bond Mill test applies for coarser ball milling, but is not appropriate for stirred milling with fine media grinding to 70 microns. With no industry -standard test, the energy requirement is often made on the basis of supplier estimates or benchmarking against similar applications. Yet suppliers use vastly different scale-up methods which result in widely different energy estimates. Estimates can differ by 100-300% even for similar mills. This must result in serious errors to install either too much or too little grinding power. This paper explores this by comparing the actual performance of full scale regrind mills against their original design estimate. It confirms that serious scale-up errors have been made, and have then been perpetuated by ?benchmarking?. The test conditions to achieve accurate power estimation are discussed. The essential test conditions are: continuous (not batch) tests, ensure steady state (no coarse fraction retained in test mill), correctly account for classification, measure energy directly (not inferred), and using the same media size as the full scale installation. Failure to correctly address even one of these factors can bias results by 40%; failure to address several multiplies the error.

Jan 1, 2011

By A. D. Davis

Limestone-based material shows great promise for removal of arsenic from water. In laboratory tests, it has removed more than 95% or arsenic and more than 99% of cadmium and lead. In addition, the waste material appears to be suitable for recycling or disposal in an ordinary landfill. However, the efficiency of limestone for arsenic removal could be improved. Recent research has shown that iron treatment of limestone can enhance its arsenic-removal efficiency greatly, increasing its attractiveness as an alternative to other methods.

Jan 1, 2012

By L. A. Weakly, D. A. Weiss, R. B. Crookston

A presentation of experience gained from using mechanical and conventional equipment for excavating shafts, raises, tunnels and other openings in various Colorado oil shale mining properties.

Jan 1, 1983

By Daniel Journeaux

Introduction Daniel Journeaux is President of Janod Incorporated. Janod is a family owned and operated company that has been working in the field of slope stabilization since 1970. Daniel has worked in the rock stabilization industry for 25 years and has been President of Janod since 1992. Daniel has been an invited speaker for the Federal Highways Administration for the Northwest and Southwest divisions, Queens University in Kingston Ontario, The University of Laval, Vulcan Materials Company, CSX annual meeting for the Northeast Division. Daniel has written several articles and has been published in Pit and Quarry, World Tunneling, and American Shotcrete Association magazines. What is Required to Remediate Highwalls There are several techniques available to stabilize highwalls or temporary rock walls to allow for safe mining practices. The following are some of the techniques that can economically be used.

Jan 1, 2005