Search Documents

By Andreas Rubo, Stephen Gos

In the days of increasing environmental and safety awareness many efforts have been made to prevent losses of both an evident economic nature and also less obvious losses. These losses could be associated with damages due to negative impact on the environment and also people coming into contact in a broader sense with any toxic chemical. This paper deals with how cyanide can be applied in a responsible manner at a modern gold mine. Responsible application is achieved by minimizing losses of reagent and avoiding negative impact on the environment as well as adopting a Responsible Care philosophy to the application of cyanide. It becomes evident that this is quite a complex system with a greater commitment than avoiding reagent losses for economic purposes.

Jan 1, 1997

By Ron VanRiper, Ben W. Burdett, Randy A. Ynchausti, Jeff D. McKay, Dan Lampshire, Thomas W. Toronto

An adaptive process control system was installed in Cortez Gold Mines Mill #2 Grinding Plant in Nevada. The installation, commissioning, and testing of the system took approximately 80 manweeks, but final test results show that the system paid for itself through increased throughput within two weeks of commissioning. Both crisp and fuzzy rules are used in the expert rule base which is also integrated with continually adapting neural network models. The expert rules and models are used by predictors, and optimizers to allow the control system to provide optimum process performance under continually varying feed conditions. The selection, installation, rule and predictor configuration, and statistically verifiable testing of the control system in the Cortez Gold Mines Mill #2 Grinding Plant is described in the paper.

Jan 1, 1999

By P. M. Lin

The problem of surface subsidence over abandoned mine lands is becoming more common due to the development of housing in suburban areas of abandoned mined lands. Subsidence can induce damage to estate properties, engineering structures and the environment. Houses, buildings, roads and utility pipelines may be fractured or broken or may collapse due to subsidence. The ground surface may be depressed and sink gradually or suddenly. The surface and subsurface water flow may be disrupted causing a change in flow pattern or depression of the water table. However, techniques for predicting abandoned mine subsidence are not yet well developed. Presently, one cannot predict when and where mine subsidence will occur. People have to wait until it occurs and then apply a suitable measure to remedy the damages.

Jan 1, 1990

By A. B. Phillips

The Randfontein Estates Gold Mining Company (Witwatersrand) Limited (REGM) operates three metallurgical complexes for the recovery of gold from the Witwatersrand Gold Reefs at the town of Randfontein, 40 kilometers west of Johannesburg. Mining operations in the. area commenced in March 1889 and ceased temporarily in 1965 when the viable ore reserves had been depleted. Exploratory drilling in the 1960's indicated viable deposits of gold in the Elsburg reefs, south of the Witpoortjie Horst Block, _which formed the Southern limit of the previously exploited areas. Three shaft complexes have been established to exploit this area, known as the Cooke secti'on. In 1983 the Doornkop shaft was sunk to the north of the Cooke section to mine Kimberley reef and the South reef.

Jan 1, 1992

By Jim V. Rouse

The decision to hold parallel conferences dealing with hazardous waste and mining waste grew out of the conviction that there were advantages to having personnel serving the two groups talk to each other, as both groups develop cost-effective and environmentally-protective solutions to present and future waste-disposal problems. There has been a certain amount of "reinventing the wheel" which could have been avoided by a better dialog between the two groups. The intent of holding the two parallel conferences is to allow for networking, to minimize future needless redundant effort. The opening session panel speakers represent expertise from both industries; I feel honored to speak as one with a history of serving both groups as a specialist in the subsurface behavior of heavy metals.

Jan 1, 1991

By L. Lichty

Treatment of refractory gold ores containing arsenic has always presented a major problem in their processing to recover the contained precious metal values. The major difficulties are concerned with lower recoveries and production of hazardous fumes, effluents and residues. Due to these arsenic related problems, many otherwise economically attractive precious metal deposits and dumps all over the world are not exploited. In recent years, treatment processes for refractory gold ores and concentrates have been explored. A few commercial operations employing roasting or pressure leaching have resulted. Roasting has limitations due to environmental constraints related to off gases. Pressure leaching involving high temperatures (180° to 200° C or 356° to 392° F) and pressures (2.75 MPa or 400 psi) is accompanied by high capital and operating costs.

Jan 1, 1990

By G. Gaidajis

In this paper, a semi-qualitative methodology is presented and then applied to an aluminium extrusion industrial facility in order to perform an initial environmental assessment. The results of the assessment enable an improved understanding of the environmental performance of the facility and more importantly identify the areas of significant environmental concern. Following, the application of case-specific sustainability indicators related with the areas of significant environmental concern, leads to a more comprehensive sustainability assessment. The applied two-step approach offers a quick and reliable environmental assessment and help focusing on the most environmentally problematic areas. Moreover, the follow-up of the specific indicators seems to be appropriate for the improvement of the environmental performance of the examined industrial facility.

Jan 1, 2008

By David Shuck

On November 1991, Homestake Mining Co. completed the installation of a $5.7-million, 2.7-kt/d (3000-stpd) flotation circuit into the flowsheet of the McLaughlin Mine in California's coastal mountain range, about 113 km (70 miles) north of San Francisco. This addition reduced overall operating costs and improved the gold recovery of the low-grade refractory reserves over that expected from direct cyanidation. In addition, flotation provided a means to generate a sulfide concentrate that is used to supplement feed to the pressure oxidation circuit. The McLaughlin operation started in 1985 as the first pressure oxidation plant for treating sulfide refractory ore. During the mine's short history, efforts have been made to reduce costs and increase production through process development.

Jan 1, 1994

By Dennis A. Beiter, William J. Francart

Barometric pressure changes have been an important consideration in the sealing of mines, especially in the case of mine fires. These changes are caused by storm fronts and regularly, on a daily basis, by atmospheric heating and cooling. In many cases, anticipation of these fluctuations in a mine sealing operation or recovery can be an important consideration when scheduling activities. The barometric pressure changes create pressure differentials across sealed areas, inducing airflows which may create explosive mixtures of mine gasses, cause intensification of fires, and create irrespirable atmospheres outby seals. These effects of barometric pressure fluctuations on mine fire sealing and recovery operations are discussed. Data available from the National Weather Service is also discussed as a tool for predicting barometric pressure changes.

Jan 1, 1997

By Jack G. Pippenger

The Coteau Properties Co.'s Freedom mine is a surface operation near Beulah, ND that produces more than 13.6 Mt/a (15 million stpy) of lignite. Coteau, a subsidiary of North American Coal Corp., ranks among the largest mines in North America. In 1994, Coteau ranked eighth in annual coal sales, becoming the largest mine outside the Powder River Basin of northeastern Wyoming. However, for the Freedom mine to stand alongside the Powder River Basin heavyweights, Coteau had to overcome several obstacles. These included a coal seam with three-quarters the heating value and overburden-to-coal ratios three times higher than Powder River Basin mines. Coteau's ability to compete has been built around a program of continuous improvements in productivity, cost efficiency and innovation.

Jan 1, 1995

By J. C. Danza Errico

The bauxite deposits on the Pocos de Caldas Plateau in the state of Minas Gerais, Brazil, were formed by the differential weathering and leaching of alcaline rocks in a ring structure. Their action on steep topography formed heterogeneous ore posture and chemical grades. Variographic analysis of several of these deposits show nested structures that are probably related to ore genesis. Kriged ore reserves estimation are presented with emphasis on the data pro cessing method that was employed. Programs were written in APL. Its intrinsic use of matrices contributed to faster programming and less computer time. In many cases looping was eliminated. The high resolution graphic resourses of APL. workspace facilitated programming of variogram analysis, fitting, and regularization. APL sub-routines are presented for variogram calculation and kriging.

Jan 1, 1986

By M. K. Pathak, A. K. Mukhopadhyay, D. C. Panigrahi

Changes in machinery operating and design parameters often result in unexpected vibrations or changes in the vibration patterns. Vibration in a system is an undesirable element that can cause machinery distress. Potential damage can be prevented by identifying the vibration level that is due to the changed operational parameters. This is necessary for the safe and reliable operation of plant equipment. This paper presents a documented study on vibration events that resulted from alterations in operating and design parameters in a mine ventilation fan and analyzes the causes by defining the sequence of events that led to its performance deficiency. This paper is based on experimental effort to study the vibration behavior of a ventilation fan under varying operating conditions.

Jan 1, 1999

By M. R. Moon

The fire at Wilberg Mine in 1984 reached the surface resulting in the failure of the vertical ledge forming the roof and entrance for three main intake portals. The fallen material was covered with a concrete cap to seal the air from the mine. As the mine was recovered and ventilation pressure was placed on seals on the perimeter of the fire area, the concrete capped rubble proved ineffective. Due to the steep and rugged terrain and the inaccessibility to the portals from underground, horizontal holes were drilled into the portal entries and three seals were placed remotely. The seals, in conjunction with pressure balancing the seals around the perimeter of the fire area, resulted in the control of the mine fire.

Jan 1, 1994

By Raimondo Ciccu, Francesco Satta, Marcello Ghiani, Piero Carbini

Nonpolar oils are utilized as collectors in low-rank coals flotation processes. The analysis of the mechanism of the hydrophobic film formation on coal particles permits the identification of the main characteristics that these reagents should exhibit in order to render the process technically and economically efficient. Such requirements - low repulsive energy developed in the interaction with coal particles; limited interfacial tension at the coal-oil boundary; relatively low viscosity and, at the sake time, poor ability to absorb into the coal pores - are found in some binary mixtures of oils having different volumic mass. The features of such mixtures as well as the advantages deriving from their use for the flotation of a Sulcis coal sample and experimentally proven, are described.

Jan 1, 1989

By Peter Keppler, Stephen D. Bundy

"Due diligence" is a review or audit of a facility or business to assess and quantify risks and operating status before an acquisition. Due diligence findings can be used to negotiate the price, general terms, and indemnification provisions in the purchase and sales agreement. In addition to assessing out- standing liabilities, necessary capital improvements, and the adequacy of operating budgets, due diligence should include "nontechnical" considerations, such as local community acceptance and relations, and the effect on the company's public image and operations. This paper will discuss how these considerations can be addressed in the due diligence process and factored into the transaction. Also, innovative means for risk reduction and risk transfer, during and after the transaction, will be discussed.

Jan 1, 2001

By K. H. McDaniel, D. M. Loring

The underground ventilation system at the Waste Isolation Pilot Plant (WIPP) provides for the unparalleled ability to ensure the safety of the workers, the public and the environment. Although small spatially, the system can vary the airflow from 31.2 to 217.1 m3/s (66,000 to 460,000 cfm). The system can automatically incorporate HEPA filtration in the event of radioactive contamination. Remote-capable regulators individually control the four main splits, and they can be adjusted from the surface if necessary. A ventilation remote-monitoring and control system provides real-time information. Future areas of concern include DPM compliance, system psychrometry, logic-based real-time mine-ventilation simulation and automation using PLC technology. This paper discusses the evolution of this system.

Jan 1, 2003

By D. A. Stanley, B. J. Scheiner

The U.S. Bureau of Mines has thoroughly investigated the flocculation of phosphatic clay waste with polyethylene oxide (PEO). The studies included both theoretical and applied aspects of the flocculation sequence. The screen dewatering technique developed by the Bureau was field tested at four different Florida phosphate mines. The results of these field studies are presented. Also, to determine the mechanisms of the interaction of PEO with montmorillonite clays common to the phosphatic clay waste, a number of theoretical studies were conducted. An empirical equation was developed to describe the amount of PEO needed for flocculation. Infrared, ion exchange, and rheology techniques were used to study the interaction of PEO with Florida clays. The results of these studies are also presented.

Jan 1, 1993

By G. Sanders

Discussion by G. Sanders The studies reported on in this paper were initiated to draw attention to the severe contamination problem in the Section 30 drilling program at Chimney Creek. The lithologic-subset sampling study reached a different conclusion from that presented in your paper, and I wish to comment on your subsequent analysis of the data and your conclusions. Request for more complete data In the section on subsampling, you mention that the subordinate lithologies were separated and sampled, yet only the dominantlithology gold value is plotted in Fig. 4. In a contamination study, the reader is interested in the assay values for the individual subsets. Please include a table of the subsample assay data in your reply. Also, please indicate which analytical methods were used to arrive at the gold values in the subsampling study. Turning barren rock into low-grade ore Figure 5 is very revealing and typical of all of the cross sections in Section 30. Note the long strings of low-grade mineralization spread out for hundreds of feet below the ore zones. There were some very high gold values found in certain contaminated fractions during the subset sampling. The conclusion, here, was that the distinctive, strongly-mineralized dolomite layer was probably loose and crumbly and continued to disintegrate during drilling. This caused salting of the unmineralized rock samples below. Missing the high-grade part of the ore body In your statistical analysis, you directly compare the reverse circulation assays to the diamond drill assays in Section 30. Two points argue against a direct comparison and suggest the differences are greater than the 3 % that you report. First, any core loss in a gold zone most likely means that the true gold values are greater. The drillers lost significant amounts of the clay-rich, Section-30 gold mineralization. Also, the initiated salt-mud system, an attempt to improve the core recovery, met with little success. Second, the practice of not sampling core geologically, but instead sampling on even 5-foot intervals, adds a deliberate dilution to the core assay values by including a portion of nonmineralized rock in the first and last samples of each high- grade intercept. The result is often a pair of low-grade assay values on either side of a high-grade gold zone. In reality, a high-grade gold zone has a very sharp assay wall that is often bounded by barren rock. This sampling method may make the diamond-drill core assays more like the reverse circulation values and may help explain the statistical similarities you found. However, it does not represent the true gold values in the high-grade parts of the deposit. You cannot deny that, by careful geological sampling of the drill core, higher and sharper assay values will be obtained. The low core recovery and the diamond-drill-core sampling method used act together to lower the diamond-core assay values. The 3% difference you found between the reverse-circulation and diamond-core assay values could be much larger when you consider what the true diamond-drill core values would be with optimum core recovery and a geologic sampling method for the core. Should statistics have been applied here? The statement "... that reverse circulation holes have overestimated the values of some ore zones and underestimated the values of others" (p. 345) is not correct. The subsampling confirmed what the cross sections hinted at in Section 30. Namely, beneath the high-grade zones, the reverse circulation holes created, by contamination, large intercepts of low-grade ore in regions of barren rock. Because the low-grade material was not there to begin with, this is not a process of overestimating low-grade mineralization. The next statement that "the average result is similar to that of the diamond drill holes" may apply to the data set numerically, but it is not true when viewed spatially on cross sections. Adjacent reverse circulation and diamond drill holes are almost impossible to correlate, high-grade zone values vary widely and many low-grade intercepts make no geologic sense. The subset sampling and cross sections presented in the first part of the paper show that the reverse circulation portion of the data set has some serious problems, as highlighted above, and should not have been dealt with statistically at all. Conclusion Each ore body is different, and each drilling method presents unique sampling problems. In this case, the diamond drill is the

Jan 1, 1994

By Y. B. He

The effect of the overflow to underflow (O/U) flowrate ratio of a dense medium cyclone on its performance is tested utilizing a 6" dense medium cyclone and density tracers. The results show that the O/U flowrate ratio is clearly correlated with the separation cut point D50, the separation efficiency Ep, the density differential 0, and short circuiting of the cyclone. Within certain limits, a higher O/U ratio results in a better separation efficiency, a higher D50 and an increased density differential. A lower O/U ratio, on the other hand, reduces the cut point shift and density differential. The phenomenon of short circuiting to the underflow, which is especially significant for fine particles, is directly connected with an excessively low O/U ratio.

Jan 1, 1992

By M. R. Fletcher

Slags generated by the ferrous-metals industry can be used to produce high-tech ceramic materials. The properties of these ceramics can be controlled by judicious choices of composition, additives, and processing parameters. Standard methods of materials handling, such as comminution and mixing, are as applicable to slag as to any other mineralogic raw material. In this study, foundry slag was ground, homogenized, melted and formed to produce a glass, and then heat treated to crystallize it into a high-strength glass-ceramic. The product shows promise as a low-cost wear-resistant tile material which can be custom cast. This and similar materials, made from slags and natural rocks, are candidates for use as construction materials, acid-resistant piping, shock-resistant sheathing, rot-proof pilings, and, when foamed, even as pontoons.

Jan 1, 1988