Search Documents

By Steven W. Hunt, J. Patrick Powers, Roger C. Ilsley

Artificial groundwater recharge has been used successfully to mitigate water level drawdown in upper alluvial deposits during construction of the Milwaukee deep rock tunnels. Recharge wells in rock as well as soil were used. The effort reduced settlements from consolidation of compressible estuarine deposits, and has minimized damage to existing structures. The paper describes the geology that presented the consolidation problem, and the hydrogeologic conditions that caused the drawdowns. Also presented are the details of recharge well design, construction, operation and performance in an urban environment. The project design calls for grouting and lining of the tunnels to control groundwater in the long term.

Jan 1, 1991

By J. L. Huiatt, D. G. Foot, J. D. McKay

The US Bureau of Mines compared column flotation using either fine or coarse bubbles with conventional flotation on a Montana chromite ore. On deslimed ore, fine-bubble column flotation produced a &.7% Cr2O3-grade rougher concentrate with 87% recovery, compared with 43.8% and 43.5% Cr2O3-grade rougher concentrates with 85% and 77% recovery for coarse-bubble column flotation and conventional flotation, respectively. On undeslimed ore, coarse- and fine-bubble column flotation produced rougher concentrates containing approximately 41.5% Cr2O3 with 95% recovery, exceeding conventional flotation, which produced 35.6% Cr2O3 -grade concentrates with 87% recovery.

Jan 1, 1987

Introduction The art of ripping has been around since the Romans built the Appian Way, but only in the last decade has ripping emerged as a close competitor with drilling and blasting in breaking up heavy rock formations. That is not to say ripping is as effective in every case, or even applicable in all cases, but it does provide a cost efficient option in many situations-if the optimum ripping techniques are used. Originally designed only to loosen hard pan, the ripper has evolved into a powerful tool, its capability increasing as the weight and horsepower of tractors increased. The tractor-mounted ripper extended the range of ripping because of the additional weight it brought to bear on the ripper tooth. Tandem ripping added the weight and power of a second tractor, extending the rippability range even further. Of course, the use of ripping depends on the type of material to be ripped. Not all rock can be ripped. Determination of rippability-an art in itself-is often inconclusive but there are certain universal principles that can be considered in the first step toward optimizing ripping techniques. Each of the three basic rock types, igneous, sedimentary, and metamorphic, exhibits characteristics that bear on rippability. Igneous rocks are the most difficult to rip because they lack the stratification and cleavage planes essential to ripping hard rock. Sedimentary rocks are generally the most easily ripped since they are built of layers differing in material, texture, color, and thickness. Metamorphic rocks vary in rippability with degree of lamination or cleavage caused by transformation from pre-existing rock. The condition of rock also affects its rippability. Although sedimentary rocks offer the best opportunity to rip and igneous and metamorphic the least, decomposed granite and other weathered igneous and metamorphic rock often can be ripped economically. Little or no trouble is encountered with hardpan, clays, shales, or cemented gravel. Likewise, highly stratified or laminated rocks offer good possibilities for ripping. However, thicklybedded rock formations generally must be drilled and blasted. The physical characteristics that favor ripping may be summarized as follows: • Fractures, faults, and planes of weakness of any kind; • Weathering, resulting from temperature and moisture changes; • Brittleness and crystalline nature; • High degree of stratification or lamination; • Large grain size; • Moisture permeated clay, shale, and rock formations; and • Low compressive strength. Ripper Types A second fundamental to optimal ripping is choosing the right equipment for a particular job. There are three types of rippers-the hinge, the parallelogram, and the adjustable parallelogram. In the hinge ripper the linkage carrying the beam and shank pivots on a fixed point at the rear of the tractor. The resulting arc from up and down movement causes up to 30° differential in the tip-ground angle. Thus, the tooth angle changes as it enters and proceeds to ripping depth. The parallelogram ripper's linkage maintains the same tip-ground angle regardless of tooth depth. This type of ripper has advantages over the hinge-type when ripping above maximum depth, but does not provide the aggressive tooth angle necessary for hard-to-penetrate materials. The adjustable parallelogram combines the benefits of both the hinge and the parallelogram rippers. It has the additional benefit of being able to vary the tip angle to the optimum angle of penetration. It can also be adjusted while moving, for the optimum ripping angle in any material. Several other factors that are important in selecting the right ripping equipment are down pressure available at the tip of the ripper, tractor flywheel horsepower, and the tractor's gross weight. Down pressure at the tip determines whether ripper penetration can be obtained and maintained. Flywheel horsepower rating determines whether the tractor has the power to advance the tip. The tractor's gross weight determines whether the tractor will have sufficient- to use the horsepower. The best ripping procedure depends on the job's actual conditions. While conditions, vary, it is still possible to apply certain proven techniques to a typical ripping situation. Caterpillar Tractor Co.'s Handbook on Ripping says optimum ripping efficiency can be realized if-before actual ripping begins-these questions and answers are considered.

Jan 1, 1983

By Basil S. Fee

INTRODUCTION Probably the most important family of chemicals used in mineral processing today is a category of basic commodity chemicals loosely denoted as pH regulators. Typical chemicals which are referred to as pH regulators include lime, magnesium hydroxide, soda ash, caustic soda, ammonia, sulfuric acid, and hydrochloric acid. These chemicals are often used in very significant amounts in almost all of the major mineral processing operations such as flotation, hydrometallurgy, etc. (in dosages up to ten pounds per ton of feed ore treated). While cheaper in cost per unit weight of chemical than more specific chemicals such as collectors, frothers, extractents, etc., the overall cost to the mill operator is generally higher with pH regulators per ton of ore processed than with any other given processing chemical. For example, a rough rule of thumb in sulfide mineral flotation is that the cost of lime is double that of the collector(s) used. The symbol pH is used to designate hydrogen ion concentration. When acids, salts, and bases are dissolved in water, individual molecules are dissociated into their constituent radicals or ions. The strength of an acid or a base increases with the extent of such dissociation or ionization. An alkaline solution is one in which the number of Qydroxyl ions (OH ) exceeds the hydrogen ions (H ). In an acid solution, the hydrogen ions predominate. In either case, both ions are always present as water itself ionizes to a limited extent, that is: [ ] The pH scale is logarithmic and the pH value is the negative of the logarithm (base 10) of the molar concentration of hydrogen ions per liter of solution. For example, a pH of 5 means that the molar concentration of hydrogen ions per liter is 0.00001 (1 x 10-5). Likewise, a pH of 9 means that the molar concentration of hydrogen ions per liter is 1 x 10-9. Normally, the relationship between hydrogen ion and hydroxyl ion concentration is based on the relationship: Concentration of H ion x concentration of OH- ion = constant. Eq. (1) In dilute and/or moderately concentrated solutions that are normally used in mineral procygsing processes, the constant at 25°C is 10-14. On the pH scale, the value of pH equal to 7 represents the hydrogen ion concentration of a neutral solution. pH values lower than pH 7 indicate increasing acidity and higher values than 7 indicate alkalinity. Table 1 shows the nature of the pH scale at 25°C. Temperature affects the extent of ionization of dissolved acids, salts, bases, and water so that the hydrogen ion concentration (hence pH) of a solution is also affected by temperature. As a means of demonstrating this dependency, Table 2 shows the change of the exponent of the constant (base 10) in Eq. 1 and the pH value corresponding to neutrality as a function of temperature. It is also important, for example, that alkalinity or acidity expressed by pH not be confused with total alkalinity or total acidity. For example, total alkalinity is commonly determined by titration with a standard acid solution (usually HC1). pH is a measure of the hydroxyl ion concentration of an alkaline solution, whereas titration is a measure of an alkaline solution's acid neutralizing capacity. Thus, if one takes a series of various alkaline solutions prepared using different chemicals but all of exactly the same pH (and temperature) and then subsequently carries out a titration on each solution with a standard acid, it would be observed that the various alkaline solutions would neutralize entirely different amounts of acid. As an example, 0.08 grams of caustic (NaOH) , 6.32 grams of soda ash (Na2CO3), and 8.17 grams of ammonium hydroxide (NH4OH) all have a pH of 11.3 at 25°C. One liter of each of the above solutions neutralizes 0.073, 4.348 and 8.496 grams of HC1, respectively. Therefore, depending on the specific use of any given pH regulator, special tests need to be run by the mill operator to determine factors such as: the specific technical goals to be accomplished by

Jan 1, 1986

By Jonathan Ludlow, Robert A. Jankowksi

Introduction A longwall operator can make few changes to increase output, significantly reduce respirable dust, and decrease power consumption. Reducing drum speed, and thereby cutting with increased pick penetration, is one. This article defines the benefits of deep cutting in terms of reduced dust production and power consumption. It also identifies the practical aspects of high pick penetration in terms of shearer performance and coal loading. Before examining some practical aspects of reducing drum speed and looking at the theoretical background, it is worthwhile to summarize what is meant by high penetration and deep cutting, and what potential benefits and pitfalls may be expected. Deep cutting (in the sense of high penetration rather than wide web) can be defined in one or more of the following ways: • Cutting with an average pick penetration distance higher than that used in the past. • Cutting with a pick penetration higher than the longwall operator would have used if the advantages of deep and slow cutting were not considered. • Cutting with a well-designed shearer drum below 40 rpm. All these definitions are slightly arbitrary. They are given to provide a basis for discussion and to make the point that any move towards deeper, more efficient cutting can result in operational benefits. The benefits of deep cutting appear in many different areas. The most noticeable benefit, provided suitable instruments are available, is the reduction of airborne respirable dust. During an experiment on a longwall in the Pittsburgh seam, a nearly four to one reduction in dust levels was seen when drum speed was halved. Not all studies have shown such a big reduction, but it seems that some benefit is almost always obtained when drum speed is reduced. Production rate and specific power consumption are also affected (in a positive sense) by reducing drum speed or increasing pick penetration. Although these changes may not be as spectacular as those in dust level, they contribute to the economic return of the longwall operation. Similarly, improved washability through fines reduction may have a beneficial economic effect. Cutting with shearer drums operating at lower speeds does have some possible deleterious impacts that an operator should be aware of. For example, cutting reactions - loads imposed on the picks by the coal being cut - will be increased as a deeper cut is used. Steps must, therefore, be taken to ensure the stability of the shearer and provide an adequate haulage effort. These increased cutting reactions also result in higher loads on the power transmission system (gearboxes, ranging arms, pick boxes, etc.) from the shearer motor(s) to the pick tip. These higher loads must be anticipated and provided for with the necessary hardware. In particular, extra haulage power must be provided with low drum speeds, since haulage effort required increases roughly in proportion with pick penetration. Because the drum will be rotating more slowly or will have fewer picks, the load on shearer components will also be more variable. If suitable, robust equipment is not used, this increased vibration will decrease reliability. Benefits of Deep Cutting Lower dust levels, decreased specific power consumption, and improved product washability are the most noticeable benefits of reduced drum speeds. Although the benefits will vary greatly with mining conditions and the type of coal, some examples of what can be expected are described below. Reduced Dust Levels Figure 1 shows principal results of a study on the effects of reduced drum speed conducted on a longwall in the Pittsburgh seam (Ludlow, 1981). This figure shows that average dust production was reduced by about 70% when drum speed was halved. By making some assumptions about such quantities as coal density, it is possible to apply this proportional reduction to the quantity of respirable dust liberated per ton of coal mined. When this is done, two kinds of results are obtained: • At 70 rpm, about 1 g (15 gr) of airborne respirable dust is created for every ton mined (roughly one part per million). At 35 rpm, only 0.28-0.37 g/t (3.9-5.1 gr per st) of coal mined become airborne respirable dust. • At 35 rpm, nearly four times the amount of coal may be mined before the compliance level is exceeded, compared with 70 rpm.

Jan 3, 1984

By Frederick B. Henderson

On 10 August 1976, The Geosat Committee was organized in Denver to institute The Geosat Program. This program is an industry backed effort to evaluate and help select optimum space remote sensing systems for geological purposes. It is believed that the recommendations of The Geosat Committee can be supported by industry as additional exploration tools which can materially benefit industry and the Nation with respect to our energy and other natural resources needs. Appended is a general summary of The Geosat Committee Organizational Meeting and general review of The Geosat Program. The Geosat Workshop Report. The Geosat Committee, and The Geosat Program will be reviewed at a special afternoon session, Friday, 3 September.

Jan 1, 1976

By T. Zoltai

Asbestos is a generic term for industrially useful fibers recovered from exploitable deposits of the asbestiform varieties of five silicate minerals: chrysotile, anthophyl-lite, actinolite-tremolite, cummingtorute-grunerite, and rie-beekite. Asbestos and asbestiform fibers of some other minerals are known to be carcinogenic. Minerals crystallized in the asbestiform habit-are characterized by unique properties (morphology, strength and flexibility, physical and chemical durability, and defect-free surface structures). The key to the unusual properties, and health effects, of asbestiform fibers appears to be in their unusual surface structure. In contrast, non-asbestiform crystals of the same minerals, including the five so called asbestos minerals, do not have these properties and are not carcinogenic.

Jan 1, 1989

By Daniel G. Ganey

Kerr-McGee Coal Corporation has used diesel face haulage and support equipment at its dual-seam Galatia Mine in Southern Illinois since production activities commenced in 1983. The mine began production from its lower seam, the Harrisburg No. 5 coal seam, in October 1983 and from the upper Herrin No.6 coal seam in April 1985. Before production began, the company developed a program designed to make use of the flexibility offered by diesel equipment. While productivity was an important goal, the top priority of the program was to provide a safe and healthy work environment for the miners. Management believed that high productivity would naturally follow. History has proven this belief to be true.

Jan 1, 1990

By J. Jeremy Burden, Bruce S. Brown

A major question in the design and permitting of a tailings storage facility is the quality and quantity of seepage which will occur from the base of the tailings facility into the underlying foundation and groundwater regime. A corollary to this is what liner system, if any, is necessary to protect the groundwater regime from unacceptable contamination. Modern tailings storage facilities are generally designed as drained tailings deposits whereby all free water is removed from the facility by decant, drainage and evaporation. This removes the source of on­going seepage and allows for efficient and timely reclamation of the facilities. Quantifying the residual seepage from the base of the tailings deposit is complicated due to the following factors:

Jan 1, 1992

By C. H. Bucknam, A. M. Raichur, M. Misra

Simultaneous dissolution of mercury along with gold occurs during cyanidation of gold ores. A method has been found for the efficient removal of mercury from the gold cyanide solution by treating with dithiocarbamates which form stable compounds with mercury. The mercury concentration in the leach solution can be brought down to low levels by adopting this treatment. Furthermore, it is also possible to stabilize the mercury in the ore heap itself by addition of this reagent so that mercury does not dissolve in the cyanide solution during heap leaching. Only trace amounts of mercury were detected in the pregnant solution obtained from a heap treated with dithiocarbamates. In this paper, process parameters are discussed in detail.

Jan 1, 1997

By James H. Lammers

Over the years, the chemical processing industries have con­tinued to move from batch to continuous processing in order to obtain better quality control, simpler designs, and often reduced capital and operating costs. One exception to this trend has been the carbon elution circuits in the gold industry. Although some successes have been achieved on a pilot scale, no continuous elu­tion circuit using Anglo American Research Laboratory (AARL) methods has ever been used on a commercial scale until now. This paper describes the continuous elution circuit which was recently commissioned at a major gold project. The paper also presents the economic justification for the selection of the process over conventional batch technology.

Jan 1, 1998

By Bruce W. Cavender

There is a tendency for managers of mining companies to regard the performance of a process plant as essen­tially fixed, with only incremental improvements to be realized by optimizing individual unit operations. However, a number of op­erations management methods are available that will substantially improve plant performance, through both productivity increases and cost reductions. Known collectively as "world-class manufac­turing" techniques, these include total quality control, just-in-time production and inventory management, the systematic develop­ment of innovative plant practices, and progressive management accounting and business control systems. The implementation of these techniques by plant managers and operators will enable the plant's performance to exceed levels that are currently believed to be maximized.

Jan 1, 1993

By J. H. Heintz

This paper discusses the law as it relates to appraising operational mining properties in the context of a takings claim. Topics include the need for valuation expertise, the differences between de jure and de facto takings, an overview of the law of condemnation, including jurisdictional issues, and defining your strategic options according to the controlling statute. State condemnation law varies by jurisdiction and just compensation can be calculated by comparable sales unit-times-price, before ¬after-valuation, capitalization of income and discounted cash flow methods. Takings under Federal laws are reviewed, as is the necessity of assembling a team including attorneys, valuation experts including a mineral appraiser, a real estate appraiser, economists and geologists.

Jan 1, 2002

By William R. Bond, Jim V. Rouse, Laura L. Damon

As noted by Damon (1990), "The time that a heap (of gold ore) is on the reusable leach pad is of critical economic importance." The Interim Neutralization Study, conducted by Brohm Mining Corporation (Brohm), at the request of the South Dakota Department of Water and Natural Resources and reported by Damon indicated that improvements could be made in leaching and pointed out the need for a better understanding of the gold ore leach procedures. To provide data on an actual heap, personnel from Brohm and GEOCHEM installed a series of pressure/vacuum lysimeters in an active Brohm heap, and conducted subsequent testwork to evaluate the efficiency of leaching. The objectives of the testwork included efforts to:

Jan 1, 1992

By R. Z. Pyrih

Pressure/ ,acuum lysimeters were used to instrument column tests containing several lifts of tailings slurry, and to sample pore water as the tailings lifts dried. The results of the column testwork demonstrated that air oxidation of sulfide minerals associated wilh the tailings residue neutralized the alkalinity of the tailings pore water. Neutralization of the alkaline pH volatilized cyanide which, in turn, destabilized copper-cyanide complexes and caused the precipitation of insoluble copper from solution. Analyses of pore water samples for microbial activity indicated high plate counts. The presence of viable microorganisms in the pore water implied that degradation of cyanide was enhanced by growth and activity of cyanide-consuming microorganisms in the tailings material.

Jan 1, 1991

By D. Royston, D. Denlay

Pulp lifters are used to discharge ground pulp from non-overflow grinding mills. In straight-radial channel pulp lifters, discharge is often incomplete and back-flow down the pulp lifter can occur. Leading-curve channel pulp lifters can be used to ensure complete discharge, especially at high mill rotational speeds. The complex motion of solid materials in pulp lifters has been modelled mathematically for both straight-radial and curved pulp lifters in order to make comparisons between the two types. The model is supported by practical observations of the performance of curved pulp-lifters in a commercial 24ftSAG Mill as well as observations of the discharge from several commercial straight-radial pulp-lifter AG/SAG Mills.

Jan 1, 1999

By R. L. Grayson

Compliance standards for respirable dust, which are reduced because of high quartz concentrations, have become an industry-wide problem. Research on the physical and chemical character of quartz-classified particles in respirable coal mine dusts indicates that they may exist in intermixed layers or may he coated by clay or coal material. The relative amount of intermixing varies with the coal seam being mined. If most of the quartz particles of a mine dust are "pure," then the dust may have a high fibrogenic risk potential because of truly free silica and the compliance standard should he lowered. If, however, the quartz is locked inside another material matrix, or coated, a reduced compliance standard may not he appropriate.

Jan 1, 1991

By John E. Tilton

Looking back on the second half of the 20th century, future historians, I believe, will be fascinated by two major political upheavals. The first is the environmental revolution in the 1960s. It erupted in the United States and parts of Western Europe and then swept across the rest of the globe like a wild fire. The second event is the collapse of the Soviet Union. It was the last of the world's great imperial empires. With its demise went central planning as a viable economic system. History, I suspect, will see this second revolution as an offspring of the first. This is because economic and environmental issues were largely responsible for the unraveling of the Soviet Union.

Jan 1, 1994

By Michael Brittan

For several years, Independence Mining Co. (IMC) has routinely used oxygen fluid-bed roasting to pre-oxidize refractory gold ores ahead of conventional carbon-in-leach (CIL) processing. Oxygen serves jointly as the fluidizing medium and the combustion gas. This technology has proven to be reliable, environmentally sound and cost-effective. IMC is a subsidiary of the Minorco group. The company operates the Jerritt Canyon (a joint venture with FMC Gold) and Big Springs gold mines in the Independence mountain range north of Elko, NV. Ore bodies in the range contain characteristic refractory ore. It requires pre-oxidation ahead of conventional CIL processing. This article describes the technology developed specifically to treat these difficult ores.

Jan 1, 1995

By Clifford R. Haryett

The potash industry in Saskatchewan, Canada, has advanced in numerous mining and ore processing areas over the last decade. This article describes these innovations and their effect on the industry in the area. During the 1970s, Canada's Saskatchewan province became a world leader, second only to the USSR, in potash production for crop fertilizer. Despite a serious oversupply in the early part of the decade, and a drop in demand due to the agricultural impact of the oil crisis, the Saskatchewan potash industry continued to make extensive capital expenditures to bring mining and processing innovations onstream. These innovations were directed at reducing production costs, improving work conditions, and overcoming environmental concerns.

Jan 8, 1982