Search Documents

By Roger Beckie, Leslie Smith, Craig Nichol

To study the hydrogeological processes that control the movement of water through unsaturated waste rock, an intermediate-scale (8m x 8m x 5m) waste rock pile has been constructed and instrumented. The constructed pile is monitored for moisture content, matric suction, temperature, matrix water chemistry, gas chemistry, gas pressure, rainfall, evaporation, discharge volume and discharge chemistry. The pile is built upon a grid of 16 contiguous lysimeters. The experiment is designed to investigate the mechanisms that create rapid water flow through a pile and its exchange with slower-moving matrix water.

Jan 1, 2000

By T. D. Rourke, Fred H. Kulhawy, O&apos

From mid-1976 to early 1978, a 5.64 m diameter tunnel, 2491 m long, was excavated by a modified Robbins full-face TBM under shallow cover in highly stressed sedimentary rock in Rochester, NY. In-situ stress measurements were made, and tunnel behavior was monitored with MPBXs, inclinometers, tape extensometers, and instrumented steel ribs. Detailed geologic mapping was also done. In this paper, the as-monitored tunnel behavior is described, and the TBM performance is evaluated from field records. Recommendations are also made for future tunneling in similar geologic environments.

Jan 1, 1981

By J. A. Finch

The use of pneumatic methods for measuring interface level in flotation columns is analysed. It is shown that errors can vary over a wide range (e.g. 40 cm. in one industrial application) depending on bubble size, particle size, bubble loading, liquid hold-up and bulk slurry density. Accurate measurements (+ 5 cm) can be obtained by measuring intensive properties of the froth near the interface. Methods based on the measurement of temperature and conductivity are described and analysed. Control of the interface level using these measurements subject to various disturbances is demonstrated.

Jan 1, 1988

By P. Sotiropoulos

In the framework of the Specific Programme: ?Promoting Competitive and Sustainable Growth? a detection system was designed and developed in order to provide an added value service beyond standard instrumentation. In the hydrocarbon industry it will be possible for the first time to detect in a pulse regime, two types of radiation emissions using a single device. This means that any saturation of hydrocarbons can be detected, irrespective of the degree of formation water mineralization, which is a major limitation on currently available neutron-gamma tools, where the formation water has a low mineralization.

Jan 1, 2006

By William R. Nash

Introduction As ore grades decline and deposit depths increase, problems and costs of mining construction increase rapidly. Ground water greatly impacts the cost of mining construction. In developing or exploiting ore bodies or coal mines, stored ground water in waterbearing formations is often encountered. Man-made conduits or shafts are constructed, as are raise bores for ventilation (up to 6-m-diam or 20-ft-diam), or smaller diameter drill holes, used for either power cables or rock dust. In underground construction and mining, it is possible to inherit unmapped and abandoned drill holes either from oil or gas exploration, or from previous geological investigations. There also exists within underground work exposure to faults, fissures, and jointing. A mine development may encounter unknown aquifers or, unluckily, have an ore body that is an aquifer. Water may invade an existing underground structure, due to concrete deterioration or to damage that may occur to an existing shaft or tunnel concrete lining. An underground development may intersect a drill hole that was not properly grouted when abandoned. It subsequently formed a conduit or an active path to conduct water into the mine. Water inflow may range from insignificant to a magnitude sufficient to inundate an area or an entire underground development. Corrosion imposes major costs. In shafts, it can cause accelerated wear and deterioration, and subsequent early replacement of hoisting ropes. It can also cause deterioration, misalignment, and subsequent accelerated wear and replacement of timber and steel guides and buntons. Utility maintenance (power cables, air, water, and ventilation lines) also can become a problem. Corrosion imposes major costs. Skips and skiploaders provide a never-ending series of maintenance headaches when exposed to an ingress of water. Numerous problems are found in declines with invert and rail maintenance and with partitions in over-under coal mine slopes. Ground water interacting with an underground ventilation system can result in: • Increased ventilation resistance due to roof falls and the spalling of ribs caused by ice heaving. • Restriction in shaft or slope cross-sectional area due to ice buildup during winter months. This may be a safety hazard to access as well. • An increase in the moisture content entering the ventilation air that condenses underground and causes electrical and equipment maintenance problems. Underground structures also incur water-caused problems. The concrete lining in shafts, slopes, and tunnels may be subject to: • Active mine waters causing concrete and reinforcing steel to deteriorate - perhaps to the point of collapse. • Load redistribution around a concrete lining, caused by soil dislocation due to water movement. The resulting stress may be in excess of the calculated design loading. Backwall injection with grout of the completed concrete lining may solve these water inflow problems through low-pressure injections of cement and chemicals. This fills voids at the interface of the concrete lining with either the soil or rock excavation. Surface structures may be jeopardized by lowering the ground water table, resulting in surface settlements. Surface settlements can occur in buildings, headframes, hoist foundations, mills, conveyor structures, or in rail haulage. Areas of differential settlement can lead to derailments, improper wear of hoisting ropes on sheaves in headframes, and the misalignment of bearings and brakes. Mud jacking and compaction grouting may remedy these problems. To reduce operating costs, increase efficiency, and increase safety, inflow water to the mine should be minimized. For an operating mine with a water problem, a water inflow survey should be taken. Quantities of water flow should be examined at all accesses (shafts, slopes, bore holes, and raise bores) at the faces, haulages (rails or conveyors), and sump discharge. From this examination and quantity survey before and after heavy rainfalls, valuable data for elim-

Jan 3, 1984

By Alfred Weiss, Andrew E. Nevin, Thomas J. Neil, O&apos

As Edward E. Runyan, 1983 AIME President, in an interview excerpt in ME, June, p. 607, stated, "...the AIME Transition Committee has recom¬mended to the AIME Board that each Constituent Society be allowed the option of separate incorporation, whereby each could become its own separate legal entity." Background The American Institute of Mining Engineers (AIME) was formed in 1871 by 22 engineers in Wilkes-Barre, PA. Although originally a mining organization, it became a home for metallurgists, iron and steel industry people, and for the individuals in the expanding petroleum engineering profession. There are now four Constituent Societies: Society of Mining Engineers, located in Littleton, CO, 29,000 members; Society of Petroleum Engineers, located in Dallas, TX, 47,500 members; The Metallurgical Society, located in Warrendale, PA, 10,000 members; and Iron and Steel Society, located in Warrendale, PA, 6,500 members. Each of the four groups has grown and continues to serve the specific and/or diverse needs of its membership. As the needs and requirements of their industries and professions change, each of the Societies has perceived and initiated programs that serve their constituency rather than AIME as a whole. Therefore, each Society has recognized an increasing need for autonomy to better augment their own programs. An AIME Ad Hoc Transition Committee, with Robert Merrill, AIME Past President, as chairman, made a number of recommendations pertaining to AIME operations that were approved in October 1982 by the AIME Board of Directors. One of the recommendations was to endorse separate incorporation of the Constituent Societies on an individual-society-option basis. The AIME Board commissioned a task force of Constituent Society representatives to develop specific revisions to the AIME Certificate of Incorporation and the AIME Constitution and Bylaws. This was done to allow separate incorporation and to reflect the decentralized structure of the Institute. The SME-AIME Board of Directors subsequently approved the recommendation of SME Working Party #69 that SME pursue separate incorporation. Meanwhile, Working Party #69 continues to work with the other Constituent Societies and with the AIME Task Force on Reorganization to determine the form and substance of the separate incorporation. Why Incorporate? George Webster in The Law of Associations quoted Chief Justice Marshall's (1819) definition of corporation as: "A corporation is an artificial being, invisible, intangible, and existing only in contemplation of law. Being the mere creature of law, it possesses only those properties which the charter of its creation confers upon it, either expressly or as incidental to its very existence. These are such as are supposed best calculated to effect the object for which it was created." SME-AIME attorneys, Davis, Graham & Stubbs, have pointed out that the status of an organization operating as an unincorporated association is always unclear. At present, SME-AIME administers assets of almost $3.5 million (mainly property and inventory) but technical ownership and ability to enter into contractual relationships resides with AIME. However, the operation appears to outsiders (particularly those with whom SME-AIME does business) to be an independent operation which would be expected to be a legal entity in its own right. Advantages of Incorporation Liability. Because of legal ownership by AIME of all assets of the Constituent Societies, those assets are subject to the claims of any of the creditors of AIME or any of its constituent parts (i.e., the other societies). Liabilities can be those usually encountered in business but also encompass special risks, which could develop if there were a careless and erroneous publication of material that might be used in practice or if standards are improperly established. The recent US Supreme Court decision in American Society of Mechanical Engineers, Inc.,

Jan 10, 1983

Throughout the 1970s, the US Bureau of Mines rode an ebb tide in Washington political circles. In rapid fire succession, the agency lost its mine health and safety enforcement responsibility (1973), a large portion of its energy research responsibility (1975), and then its fuel statistics functions plus a sizable portion of its coal R&D (1977). By 1978, johnny-come-latelies in the Energy, Labor, and Interior Departments had siphoned away from the Bureau some $125 million in program responsibilities as well as 900 of its employees. The bruising decade came to a close with a Department of Natural Resources proposal that, in its original form, would have scattered the Bureau's responsibilities to the winds. "There is no doubt in my wind," said Lindsay Norman, acting director of the Bureau of Mines (see box), "that were the Bureau to continue down the path it was on, the next step was closing the doors and going out of business." The doors are still open, but erosion of responsibilities had a devastating effect on the resources available to fulfill the Bureau's mission. Devastating, too, in terms of internal morale, considering the Bureau had six directors in a 10-year span. "When the troops are in the trenches and are being shot at," Norman said, "they need a leader-hopefully, a permanent one- that can get them advancing. This is something the Bureau did not consistently have in the 1970s." In September 1978, Roger Markle climbed aboard as director of the Bureau to rejuvenate the 70-year-old agency. He resigned only six months later* but the program Markle set in motion is being carried through by Lindsay Norman. Since Norman's appointment as acting director, he has spent considerable time on the road explaining his agency's redefined goals. At one such stop in Duluth, Norman and his two deputy directors, Charles Kenahan and Mike Kaas, answered the following questions. Lindsay, you were the principal architect in the Bureau's 1979 reorganization. How about a glimpse of what that entailed? Toward the end of the 1970s, after almost a decade of steady dismemberment, we reached what we felt was a critical point in the Bureau's history-we had the choice of redefining and strengthening our organization to meet the mineral challenges ahead, or continuing down the path toward the agency's eventual demise. We felt the Bureau's mission too important to abandon, so in 1978 with Roger Markle as director we initiated a six-month, no-holds-barred intro spection of just what the Bureau should be doing, why, and toward what ultimate national needs. And what did this self-reflection reveal? That there is, indeed, a unique federal role for the Bureau of Mines-that of a lead agency for influencing mineral decisions and pioneering tomorrow's technologic advances. Don't confuse us with policymakers, we're not. But we are policy analysts; we're scientists, engineers, and mineral professionals who can offer a sorely needed source of objective, accurate information to decision makers in both the public and private sectors. I feel there is no better brain trust in government than the Bureau when it comes to mineral expertise-of course, I'm biased. Do I understand you to say the Bureau of Mines is an advocate agency for the minerals industry? We plead no parochial interests, nor ought we, but from our viewpoint a sound minerals industry is extremely important to the broader national goals of security and a healthy economy. US dependence on foreign sources for critical minerals, the increasing noncompetitiveness of some US mineral sectors, and the array of land use issues surrounding mineral-rich lands all have much more serious implications than many otherwise informed people seem to recognize. In your estimation, how vulnerable is the US to foreign mineral suppliers? Let me make a distinction between dependency and vulnerability. The

Jan 4, 1980

By Jasinder S. Jaspal, Bradley J. Bourquin

Introduction Operation is underway at the Dutch Creek No. 1 mine of the first US longwall panel to be mined under the cooperative agreement between the US Bu¬reau of Mines and Mid-Continent Resources. The 244-m (800-ft) wide longwall face is part of a multilift longwall demonstration. A 3-m (10-ft) top slice is being extracted from the 8.5-m (28-ft) coal seam. This occurs in an area of the property where the Coal Basin A and Coal Basin B beds have come together to form one seam. This face, longest ever operated in the US, is being worked on an advancing longwall system. During the first months of its operation, this longwall face has been very productive and safe. Mid-Continent Resources operates two coal mines in the Coal Basin, located in the White River National Forest near Carbondale, CO. The Colorado Fuel and Iron Co. originally opened this property in 1895, and conducted a small mining operation for 10 years on the north rim of the basin and then abruptly shut down. Mid-Continent began operations in 1956, after the Coal Basin fields had lain idle for about 60 years. Operations commenced at the outcrop of the Coal Basin B bed situated at the 3-km (10,000-ft) elevation. At this time, coal was produced from Coal Basin A and Coal Basin B seams in the area. Since 1981, operations have been centralized at two mines, the Dutch Creek No. 1 and the Dutch Creek No. 2, both located in the center of the basin. Since 1981, Mid-Continent has shifted its emphasis to longwall mining as the primary method of production, and each of these mines is equipped with state-of-the-art longwalls using shields as the method of roof support. A 4-km (13,000-ft) long twin-bore rock tunnel is being driven at a lower elevation of 2.4 km (8,000 ft) to intersect the coal seams at depth, as they dip 12° in a westerly direction. This tunnel will enable the company to reduce costs by replacing trucks with conveyor belt haulage (Fig. 1). Mid-Continent began longwall operations in May 1976 with the US's first modern, mechanized advancing longwall face, using chocks. In August 1978, a second advancing longwall face was started. Results from two faces showed that the mining system could be used effectively to manage the difficult conditions encountered in both the Dutch Creek No. 1 and the L. S. Wood No. 3 mines. Unfortunately, low productivity and high costs plagued the company's advancing faces. The problems resulted principally from major equipment failures, poorly designed chocks and face conveyors, and the lack of an efficient, cost effective system for building packwalls. Flushing of rock between chocks and roof control were also major problems. In Sept. 1979, Mid-Continent and the US Bureau of Mines entered into a cooperative agreement to demonstrate the feasibility of mining thick coal seams using the multilift longwall mining method. Two lifts are to be used to mine the 8.5-m (28-ft) thick coal seam in Dutch Creek No. 1 mine. The Bureau provided mining equipment for 180 m (600 ft) of longwall face. This included the shields, face conveyor and drive units, shearing machines, panel belt, and stageloader. As a result of previous experience in advancing longwall mining, Mid-Continent purchased an additional 60 m (200 ft) of face, including roof supports and an additional face conveyor. Design The Dutch Creek No. 1 is a slope mine located on the flank of a plunging anticlinal structure that

Jan 1, 1984

By R. H. Smith

The total energy demand in the United States increased about 4 per cent annually during the 1960's 1 and is expected to increase at the same rate during this decade. Z Fuel oil growth in the 1960's was only Z per cent per year until 1968, but it increased to 8 per cent in 1969 and 11 per cent in 1970. Fuel oil demand is expected to grow at a 6 per cent rate through the 1970's. Part of this rapid increase in demand has been caused by restrictions placed on the sulfur content of fuels. High sulfur coal can no longer be burned in many parts of the country and has been replaced by low sulfur fuel oil. An insufficient supply of natural gas has also contributed to fuel oil demand. Air pollution regulations have not only caused an increase in fuel oil consumption, but they have also caused a reduction of sulfur content in residual fuel oils. Current regulations call for 1 per cent maximum sulfur content fuels over much of the country. Sulfur contents of fuels are limited to 0. 3 per cent in certain areas on the east and west coasts. Sulfur in residual fuel oils from high sulfur imported crude oil is reduced to 1 per cent currently. However, sulfur reduction to 0. 3 per cent is difficult and expensive.4 As a result, refiners may be hard pressed to supply the market for low sulfur fuel oil. The oil shale deposits in Colorado and Wyoming potentially are a huge source of low sulfur fuel oil. It will be shown that the low sulfur content and more importantly the sulfur

Jan 1, 1972

By Henry Antwi

The decade of the 1990s promises to be one of increasing internationalization for domestic minerals producers as they scramble to enhance relative positions in highly competitive, international minerals markets. This "international mining rush" is fueled by developing countries seeking international investment capital to explore for, develop and exploit sizable mineral endowments in an attempt to support the increasingly popular, but expensive, wave of democracy and selfdetermination sweeping the world. This "fuel" typically takes the form of revised mining codes and, often, lucrative investment incentives. These incentives include favorable tax rates, royalty provisions, relaxation of import/ export constraints, depreciation schedules, profit repatriation and other variables that can positively impact mineral investment decision making. Concomitantly, in their attempts to address real and perceived short- and long-term woes associated with enhancing competitive positions internationally, many domestic explorers and producers are attracted to the prospect of finding high-grade deposits in relatively virgin areas. Combined with the investment incentives provided by foreign governments, these high-grade deposits promise lucrative potential returns from projects having short payback periods. Classic examples of this mutual desire to intensify international mining efforts by domestic producers are illustrated by activity levels in countries like Chile, Bolivia and Venezuela in Latin America and, more recently, in Eastern Europe and select locations in the former Soviet Union. As US corporations scurry to send fact-finding, technical, evaluation and financial teams to these presently popular locations, one area of the world has received little attention - Subsaharan Africa. Specifically, the country of Ghana (formerly the Gold Coast) deserves more attention than it appears to be receiving from North American mining companies.

Jan 1, 1992

By Lawrence Neal Post

Introduction Synthetic soda ash production began to decline in the late 1930s. This was due to high operating costs and waste disposal problems. Since soda ash was used as a major component in manufacturing glass, an alternate method of producing that chemical was necessary. A process to produce soda ash from trona was developed by FMC Wyoming Corp.'s predecessor, as well as an economical way to obtain trona. Existing trona operations are located about 40 km (25 miles) west of Green River, WY. Five operators presently mine trona in this area. FMC's property has 153 km2 (59 sq miles) leased. Its eight shafts reach 488 m (1600 ft) deep to the uniform trona deposit. The seam ranges in thickness from 2.4 to 3.6 m (8 to 12 ft). History Egyptian tombs, dating from 4000 to 3000 BC, contained mummies preserved by an embalming process using soda ash. For many years, soda ash was produced by burning marine plants, then dissolving the soluble material (sodium carbonate) from the ashes. The name soda ash is derived from this method of production. In 1791, Nicola LeBlanc developed black ash, or salt cake, from salt, sulfuric acid, coal, and limestone. This process remained in use until 1863, when Ernest Solvay developed a method for producing soda ash from salt, coke, and limestone with ammonia as a catalyst. This Solvay process was widely used. And, in the 1930s, there were 17 plants in the US alone. High plant operating costs and waste disposal problems, however, necessitated finding an alternative to the Solvay process.

Jan 10, 1985

By Fernando H. Muge

The first application of dynamic pro¬gramming to the problem of grade control and scheduling was by Muge et al (1979) and Ribeiro (1982) who applied it to the simple, two-dimensional case of longitudinal open stoping using two sublevels. In this paper the formulation of the problem is extended to cover the general case applied to a cut-and-fill mining method. The criterion for optimization is the total deviation of the average, grades of mining blocks from the overall average panel grade (or the average grade of a set of mining panels or the mine processing working point). This means to schedule the operation by removing a certain number of mining blocks at a time, subject to the geometric (mining) constraints, and such that the total deviation of average block grades from overall average grade is minimum. The method can be applied to complex orebodies with several ore characteristics and the deviation of each one of these characteristics can be further constrained by specifying maximum values. The method can also be generalised in order to take into account any necessary geometric constraints used to define the mining method. In this paper a case study is presented concerning the mine planning of a complex sulphide orebody located in the South of Portugal. As input for the definition of the mining sequence, a geostatistical numerical model of the orebody was built based on a previous ore typology. The short term planning is used to assess specific mining sequences and the production scheduling is performed on the basis of an objective function (e.g. minimization of grade fluctuation).

Jan 1, 1989

By Etienne Simode

When a fire breaks out in a mine access road, the hot smoke, due to heat transfer with the surrounding strata, progressively cools as it moves forward. Depending upon the resulting temperature distribution, the density of the fluid changes. This change will bring about: Firstly, a variation in the resistance of the roads, a static factor which will affect ventilation flow rates; Secondly, the appearance of extensive aerodynamic driving loads in the vertical and angled roads, a dynamic factor which can have an extensive impact on ventilation. Because of the appearance of combustion and distillation products, the vaporization of water, which wets the timbering and strata, and the expansion of gases, fluid rates can at times be increased tenfold in the area of the fire. These disturbances may cause explosions and ventilation inversions, which fill other working areas with smoke toxic to workers, and which can come up upon rescue teams from behind. Due to the progressive heating of the surrounding rocks, which will slow down heat transfer, these dangerous conditions change over time. At the Lorraine Basin Coal Mines, programs have been set up and employed for the computer simulation of these phenomena over time. They serve to anticipate or to understand such phenomena, the input data being the characteristic parameters of the mine ventilation network, the operating curve of the main fans, and measurements or estimates of some temperatures. Two programs, employed together, have been developed for these studies: One program, called RESO, calculates the distribution of flow rates and pressures throughout the entire network; The other, called FEUMIN, determines smoke temperatures over their entire path.

Jan 1, 1980

By Gary Krix

The Amdel Thickener Interface Gauge (TIG) provides continuous on-line measurement of the level of the liquid/solid interface in thickeners and Counter Current Decantation (CCD) washers. Unlike other interface level measurement systems, the TIG also determines the span of the transition zone. The transition zone is the region between the clear liquid overflow zone and the compressed solids zone. The Thickener Interface Gauge determines the level of the interface by measuring the natural radioactivity of the solids in the thickener tank using an array of up to twelve detectors mounted vertically in a stainless steel probe. All solids contain low levels of natural radioactivity while the liquid phase generally does not. The concentration of natural radioactivity at each level in the thickener therefore depends on the concentration of solids. The radiation emitted by the solids is converted to electrical pulses by the detectors in the probe and the pulse-rate provides an accurate measurement of the density. A typical count-rate profile is presented in Figure 1. The vertical axis indicates the depth in the tank referenced to the surface of the liquid. The horizontal axis indicates the count-rate measured by the TIG probe, this count-rate is proportional to the density and can be used to determine the settling rate. The count-rate at the top of the graph is relatively low, this region corresponds to the clear overflow zone which contains virtually no solids. Moving down the vertical axis the count-rate increases dramatically at the level of the transition zone where the solids content increases with the depth in the tank. In this region the settling conditions of the solid particles change from free settling to compression. Moving further down the vertical axis the count-rate reaches a plateau where the count-rate remains relatively constant although there are often small fluctuations, this region corresponds to the solids compression zone. The liquid/solid interface as measured by the TIG corresponds to the depth at which the count-rate crosses the target count-rate which is generally selected to be midway between the liquid count-rate and the compressed solids count-rate. The length of the TIG probe is selected to cover the typical operating range of the liquid/solid interface in the thickener or washer. If, for example, the minimum bed level is 3.0 metres below the surface of the liquid then the probe length is selected to extend 30 metres below the surface. The TIG probe can include up to twelve detectors and the se are spaced over the measurement range. For small measurement ranges of around one metre 4 to 6 detectors would normally be used while for larger measurement ranges of three metres or more twelve detectors would be supplied.

Jan 1, 1993

By Jurgen H. L. Stuve, Rick E. M. Widelski

Any one who has been involved with the mining or the treatment of gold-bearing ores will agree that at the end of the total process, the quantity of gold recovered is never as much as was expected. These short falls are usually explained away by claiming that:- the original evaluation of the ore being mined was inaccurate the plant treatment process is not at its optimum theft is taking place excessive dilution occurs during mining The truth of the matter is that the gold is being "lost". During all the stages of its production, starting from the mining, right through to the smelting process, a certain amount of gold is not recovered. When a newly found gold deposit is being evaluated and the drilling data being analysed, cautionary factors are applied so that the grade is not over-stated. Once the decision has been taken to start mining and development is in progress, the exposed ore is sampled. When Again, when this data is being analysed more safety factors are used to ensure that when a piece of ground is given a block-value, the gold content is not over estimated. mining actually takes place and the ore transported to the plant for treatment, the metallurgical department also introduces certain safety factors when predicting how much gold will be recovered. This shows that the quantity of gold that one expects to finally recover is already a conservative figure. The actual quantity recovered invariably falls short of this figure, in fact, South African gold mines are satisfied when achieving a Mine Call Factor (MCF) of 85%. In the last few years a great deal of work has been carried out to investigate how this unaccounted for gold is lost and what steps can be taken to remedy the situation. Previously mined areas were re-swept using the traditional hand brush method; experiments were carried out with water jets sometimes in conjunction with compressed air and even small portable vacuum cleaners were tried. None of these methods were totally successful in recovering the left over gold but the use of vacuum systems showed the most potential. the In South Africa this has resulted in introduction of high-powered vacuum systems on the gold mines to suck-up this lost gold. These were initially introduced in the mining areas, particularly old areas, to recover any left over ore. The results proved extremely profitable, So much SO that presently, well over 120 suction systems are doing this type of work. This success encouraged plant operators to look at areas of potential loss in the plant itself. This has resulted in an increasing number of machines being supplied to gold plants mainly for clean-up applications with the bonus that the material sucked up invariably contains gold.

Jan 1, 1993

By J. B. Gwiazda

Introduction Thick seams constitute a considerable portion of Polish coal reserves. In producing mines and those under construction, the reserves where the height is more than 4.5 m (15 ft) total about 24v0 of all the hard coal reserves. The reserves that are under urban and industrial areas can be extracted using stowing methods for surface protection. About 50v0 of thick seam reserves can be extracted by caving methods. Thick seam mining methods Thick seams are usually extracted by multilift methods. There are some methods of thick seam mining that generally can be divided into caving and stowing methods. The stowing method is more expensive, but must be used when mining to protect surface features. The more known methods of thick seam mining include: • extraction of thick seam in ascending order with stowing; • thick seam mining in descending order with consolidated stowing; • thick seam mining with gob consolidation; • thick seam mining in descending order with roof caving; • sublevel caving thick seam mining system; and • thick seam mining system using an artificial roof. • Thick seam mining with introduction of an artificial roof The most advantageous method of thick seam mining is the method using an artificial roof. The artificial roof usually consists of wire mesh. Such wire mesh must be durable and must prevent small rock fragments from passing through. The mesh is usually made of steel properly protected against corrosion. The artificial roof is placed on the coal floor of the top slice (Fig. 1). Caving rock falls on the artificial roof and is thus separated from the coal. The next slice is extracted under the artificial roof. The producing face of the next slice must progress within 10 m (33 ft) behind the front of the first slice. As the second producing face progresses, the wire mesh moves down on the coal floor and may be used as an artificial roof for the next slice. Thus, one artificial roof allows the extraction of several consecutive slices. Application of the artificial roof allows for clean extraction and reduces coal losses. It also eliminates the hazard of spontaneous combustion. Introduction of the artificial roof has been limited due to a lack of artificial roof laying equipment. Manual laying of wire mesh is a labor-intensive operation, and it delays face progress, resulting in poor productivity. To eliminate these problems, artificial roof laying equipment was designed at the Polish Central Mining Institute. The support and the method of laying operation is covered by a patent. Artificial roof laying powered support To extract thick seams using an artificial roof; four-leg shield supports with lemniscate linkage were developed (Fig. 2). This shield is used in the first top

Jan 1, 1988

By Brian Mangogna, Clay McNail, Weishi Mang, Adam Steimel

Together with innovatively applying modern flotation reagents and developing the breakthrough mill enterprise expert control and operating system, Doe Run Buick Mill constructed an advanced large copper rougher scavenger to process its complex Pb\Zn\Cu ore more efficiently. The scavenger circuit, featuring its own motor control center, air blower, multiple reagent loops and FrothSense+™ camera, operates both mechanically and chemically to maximize copper recovery and under expert control. Such scavenger features can be applied to zinc rougher circuits for all Doe Run mills to maximize Cu recovery during Cu special runs when the zinc rougher becomes a copper rougher scavenger.

Feb 1, 2025

By T. Tempel

In 1994 Newmont Gold Company commissioned a 2.5 Mt/a refractory gold ore roasting plant near Carlin Nevada. Many unique characteristics of this facility required use of specialized materials of construction in the areas of dry grinding, roasting, gas cleaning, and sulfuric acid production. Process conditions and design criteria that necessitated the use of special materials include; siliceous and abrasive ore, low roasting temperatures, gas streams with high concentrations of oxygen and sulfur, and stringent environmental regulations. Materials selected for use were ceramics, corrosion resistant steels, high temperature steels, and high temperature polymers, lead, polypropylene and low flammability PVC.

Jan 1, 1997

By Wolfgang Baum

The selection of roasting technology is a complex task which is primarily dependent on the ore mineralogy. Key roasting parameters are directly linked to mineralogical characteristics of the feed and vary considerably between different ore types even in the same deposit. In addition to sulfide refractoriness, other refractory conditions frequently exist. Together with various mineralogical features of the feed, they may complicate roasting testwork and process design. For most roasting scenarios, the critical economic factors are gold recovery, capital cost and environmental performance. This paper will show how these economic factors are influenced by the mineralogical ore characteristics.

Jan 1, 1992

By Laura L. Damon, Alastair McNeillie

The use of calcium peroxide for enhanced heap detoxification has been investigated on the laboratory scale using heap leach columns. The addition of calcium peroxide to the ore prior to leaching resulted in a significant increase in the rate at which the leached ore was detoxified and this led to an overall decrease in the total heap leach cycle time. This decrease could allow a minesite to increase the ore throughput or gold leaching time and generate additional revenue. The process is of particular relevance to reuseable leach pad operating though pennanent pad systems could also benefit.

Jan 1, 1992