Search Documents

By Stephen Navin, Pablo Ferradas, Carlos Silvestri, Alexander Markov, Jon Kaneshiro

In the high Andes of Peru, two tunnels are being constructed totaling nine kilometers in length at an elevation of over 4,500 meters. The tunnels convey freezing and crystal-clear waters from rainfalls, streams, and lakes for the consumption of Lima. The drill and blast 3-meter wide by 4-meter high tunnels are being driven from both ends through folded and sheared volcanic tuff, andesite, agglomerate,and limestone, where groundwater inflow is high. This paper describes the design geological and groundwater inflow investigations and construction.

Jan 1, 1999

By Corneille S. Ek

Flotation of several copper and lead-zinc ores has been carried out with mercaptobenzothiazole (MBT) as promoter. The results of laboratgory batch flotation tests have been compared with those obtained when using more common collectors like xanthates or dithiophosphates. It generally appears that MBT is an effective collector of all the sulfides, including pyrite, but that high selectivity is rather difficult to attain, except for gangue drop-out. Some kinetic tests have been performed to check the froth production rate by MBT as compared to other collectors.

Jan 1, 1995

By Jack G. Pippenger

This report focuses on the procedures required to review, prepare specifications, bid, and purchase a fully integrated computer system for utilization by engineering personnel in all phases of mine engineering. The presentation is based on the experiences encountered in 1984 in procuring an engineering computer system at The North American Coal Corporation's Western Divi- sion. A two-phase report detailing the purchasing process and subsequent utilization of the engineering computer system will be given. Special detail is also provided on the final system hardware and software setup.

Jan 1, 1989

By Fred A. Breu, Jerome C. Neyer, James F. Peters, John W. Critchfield

This paper describes experiences with methane and hydrogen sulfide gas encountered during design and construction of a sewer tunnel in rock, in Rochester, N.Y. Design explorations are summarized, including geologic setting, measurements of gasses in test borings, laboratory analyses of gas samples, and measurements of gas pressure and flow rates from a sealed borehole. Contract specifications regarding gas are outlined. Results of the Contractor's additional explorations and testing are presented, along with a description of selected equipment and provisions for ventilation and degassification.

Jan 1, 1985

By Douglas R. Shaw

The results are discussed herein of laboratory and pilot scale research which has demonstrated some exciting prospects for the exploitation of refractory gold resources by heap leaching. The research examined practical and cost effective methods of chemical; i.e., non-biological, oxidation pretreatment of refrac­ tory old ores to enable successful conventional cyanide heap leachmg. The work has focused on regenerable chemicals, in order to minimize process consumable costs. A nitric acid method has emerged which offers rapid oxidation rates (eg, 0.5 to 6 hours) on ore samples crushed typically to% to ¾-inch. Gold recoveries in simulated heap leaching tests, after nitric acid oxidation of crushed ores, were as high as approximately 80 to over 90%, in contrast, typically, to negligible gold solu­bilities without oxidation. Nitric acid oxidation was effective when applied to several sulfide-bearing refractory gold ores which required either partial or essentially complete sulfide sul­fur conversion for high gold solubilities in cyanide. Ores rich in organic preg-robbing matter also were treated successfully, as were ores which contain significant quantities of acid-consum­ing constituents. Base metals also were recovered with nitric acid oxidation from some of the ores which contain these ele­ments. The work related oxidation and solution diffusion behav­iors and the important physical, textural, and mineralogical characteristics of the different ore types. Conceptual-level feasi­bility studies have defined the principal capital and operating cost components of the nitric acid method, sufficient to allow reliable comparisons with other oxidative technologies.

Jan 1, 1996

By S. Tavani, R. E. Browner, R. Dunne

Lead is used in CIP/CIL circuit to increase the leaching rate of gold from ores. At least four mechanisms have been proposed for the action of lead in gold leaching circuits: (I) precipitation of sulphides as highly insoluble lead sulphides preventing consumption of cyanide and oxygen; (2) su,face reaction on sulphide particles forming an insoluble lead sulphide layer peventing dissolution of those sulphides; ( 3) precipitation of lead sulphide, which undergoes further oxidation to soluble lead sulphate recycling the lead to solution,· ( 4) contact reduction of lead onto the gold szaface which then acts as a secondary oxidising agent. Rotating disc studies using a pure gold disc show that small amounts (5ppm) of sulphide ions are sufficient to significantly reduce the leaching rate of gold. Lead increased the leaching rate at small concentrations but at higher levels decreased the rate of leaching. The detrimental effects of lead were only found for a pure solution when leaching the gold disc. Ores mediate the amount of lead available by ads01ption/reaction, thus, reduced leaching rates from excess lead are not serious even when 500ppm of lead ions are added to the sluny. The detrimental effects of sulphide ions could be countered by lead addition during the leaching process. A penalty, in the form of reduced leaching rate, will occur the longer lead addition is delayed. A time lag was noted between the addition of lead and the increased leaching rate when a large concentration of sulphide ions was present.

Jan 1, 2000

By J. J. K. Daemen, C. Fairhurst

Two aspects of tunnel support design are considered, and for both particular attention is paid to the influence of rock failure around the tunnel on the loads developed on the supports. 1) In general it has not been possible to extend analytical methods for the study of rock failure around tunnels to three dimensions. As a consequence it was not possible to calculate either the influence of the face or the actual sequence of support loading as the face advanced. The finite element method made this extension possible. A simplified analysis of the influence of the face and of the sequence of support installation has been made. The influence of the original stress field and of the rock behaviour on the length of tunnel which can be left unsupported (related to the stand-up time) is shown. The degree to which a 2-dimensional analysis can be used to approximate the final support load is shown to be dependent upon the post-failure behaviour of the rock. 2) Tunnel support design requires a knowledge of the forces and of the -rock displacements which cause stressing and deformation of the support system. A 2-dimensional model incorporating a detailed representation of several support systems, of the rock behaviour in the broken zone and of the interaction between rock and support is given. The model allows the calculation of the stress distribution in the support. The significance of the relative stiffness of support and rock on the stresses developed in the support is shown.

Jan 1, 1997

By S. Ubaldini

Acid mine drainage (AMD) is a common problem in different areas with a past history of mining activities, which is characterized by low pH (2-4.5) and significant toxic metals concentration. The main aim of the present work was to perform a process feasibility analysis in order to remove heavy metals (Cd, Zn, Ni, Mn, Cu) from AMD (Acid Mine Drainage) in a relatively cheap and environmentally friendly way, by means of electrowinning and biosorption. A first characterization of an Italian AMD sample was performed evidencing a zinc concentration around 2 g/L, cadmium and nickel content of about 4 mg/L, manganese of 85 mg/L and iron 190 mg/L. Electrowinning tests lead to the following metal removal after three hours treatment: Zn 99%, Ni 99.9%, Cd 99.9%, Cu 99%, Mn 87%, Fe 96%. Moreover, an high grade of purity of the metal deposit has been achieved (Zn>95%), as observed by X-ray diffraction analysis. Considering that metals concentration in the effluent was still above legal limits (in particular for Zn, Mn and Fe), a further biosorption treatment was planned in order to produce an effluent fitting environmental limits. Experimental electrowinning tests and literature multimetal column biosorption data have been used in order to perform a preliminary techno-economic feasibility analysis of the process aimed at metal removal from AMD. A treatment cost of about 6.5 ?/m3 AMD has been estimated, for a plant capacity of 10 m3/h AMD inlet flow rate.

Jan 1, 2006

By K. L. Kayler

Ball clay production in 1991 amounted to about 800 kt (880,000 st), about the same as in 1990. 1992 estimates show a 5% decrease to 750 kt (827,000 st). This decrease continued a trend of reduced production that began after the peak of 900 kt (1 million st) that occurred in 1988. Use of ball clay in sanitary ware was about 2% less in 1992, although levels of use in floors and wall tile, dinner ware and pottery remained constant. Filler, extender and binder applications continued to be important end uses, accounting for about 17% of total market. Refractory uses maintained their market share of about 17 kt (18,700 st). Use of clay liners in toxic and waste dumps is an application widely found in Germany. However, its use has not been fully exploited in the United States. This could represent an opportunity for domestic clay producers. Tennessee remained the leading source of ball clays. Other producers were Indiana, Kentucky, Mississippi and Texas. Tennessee's production, however, decreased about 3% in tonnage produced and its value dropped from 68% to 65% of total production. The ceramics division of Southern Clay Products, Inc., was bought from LaPorte plc by United Clays of Texas, Inc., a US subsidiary of Watts Blake Bearne & Co. The purchase included ball clay reserves at Troup, TX. The acquisition makes United Clays the second largest ball clay producer in the United Sates. United is also the only company mining clay in Texas. Fire clay production decreased 5%

Jan 1, 1993

By S. Serata

Background Results of the above study in the August 1991 issue of Mining Engineering offer valuable lessons in the solution of cutter-roof problems. The original study plan was initiated by the discussion authors to solve the problems using the "stress control method" of mining (Serata 1976,1982; Serata, Carr and Martin, 1984; Serata and Gardner, 1986; Serata, Gardner and Preston, 1986; Serata, Gardner and Shrinivasan,1986; Serata and Kikuchi, 1986; Serata, Preston and Galagoda, 1987) However, the plan and the planner were changed to the arrangement reported in the paper. The change was considered reasonable at the time due to the mine engineers' uncertainties about the stress control method. Consequently, the basic principle of the study was shifted from the original stress control method to the method described in the paper, which will be called the "yield pillar method" for the purposes of this discussion. The paper convinces the reader that the yield pillar method fails to solve the cutter-roof problems. This doesn't mean that the stress control method also fails. Actually the contrary is true, as discussed below. Limitation of the yield pillar method The paper illustrates clearly how poorly the yield pillar method performs in solving the problem. The reason for this failure is the lack of the protective stress envelope needed to stabilize the cutter roof. Unfortunately, the protective envelope cannot be formed properly without utilizing the stress control method of mining. Changing the pillar size does not make much difference in the roof stability.

Jan 1, 1992

By D. C. Willett

INTRODUCTION The Symposium on the Development of Underground Space, held in Seattle, Washington, from October 1 through 3, 1980, was organized by the "Deep Space" subcommittee of the ASCE's Underground Research Technology Council. The primary objective of the symposium was the exploration of the interfaces between the investigation, design and construction of large underground facilities in "deep space" which, for the purposes of the committee, has been defined as starting at 100m below ground surface. The meeting focussed primarily on tunnels, caverns and shafts in hard rock; the meeting format comprised a number of brief presentations concerned with the technical aspects of investigation, design and construction, followed by an open discussion, and concluded with the assembly of recommendations regarding the interface problem by the symposium participants. The principal considerations brought out during the symposium, and a general review of the conclusions, are briefly presented in the following paragraphs. INVESTIGATION The sessions dealing with "Investigation" were chaired by Dr. H. Pratt. Presentations were made by Dr. D.C. Banks, Dr. W.A. Hustrulid and Dr. Pratt. The extent of the interface of the investigation phase with the other (design and construction) phases of an underground facility will depend in large measure upon the nature of the facility; at one end of the spectrum, the investigation must be in continuous and closely coupled relationship with the design of a radwaste facility. At the other end of the spectrum, for (say) a small mining operation, the interface is largely associated with the initial development, with only minor on-going involvement.

Jan 1, 1981

By S. C. Suboleski

Underground long-range planning and mine design is an iterative process beginning with a specified production level, quality criteria, and geology of the deposit. Given these factors, face equipment is selected, the number of units needed and production per unit are calculated, and the mine infrastructure needs are developed. The scheduling of units then follows, with the design of the various support systems coming next. The support systems needed to maintain production can be grouped as follows: (1) outby haulage of mined material, (2) supply and manpower haulage, (3) ventilation and associated environmental considerations, (4) drainage, fresh water, and related considerations, (5) rock mechanics, and (6) power, supply. Thus, long-range planning may be viewed as a three-tiered structure, with the data on required production, product quality, and geology at the upper level; the development of face production capacity and the scheduling of units sufficient to meet the needs of the first two at the second level; and the development of support operations for the production units at the third level. Changes at any level may affect not only the items on that tier but may also cause a change to the items on the tier above and below. For example, if the rock mechanics data indicate that desired opening sizes will not be stable, then this situation will affect not only the ventilation design but also the production rate and possibly the selection of equipment itself. These, in turn, may affect the scheduling of units and the number of units, ultimately influencing the entire third tier of systems.

Jan 1, 1979

By Bruce W. Cavender

In an effort to lower production costs and improve profitability, mining companies have adopted a variety of management practices emphasizing productivity and cost containment. One set of practices that has been used successfully in the manufacturing and electronics industries is "world-class manufacturing" (WCM). It is applicable to mining as well. World-class manufacturing is based on the twin concepts of "just-in-time" inventory practices and total quality control. A few mining companies have implemented quality control programs that are similar to WCM in some ways and substantially different in others. This article considers the use of WCM in the processing environment, although the techniques are applicable throughout a mining operation. The article is also mindful of the variety of customers to whom mineral products are sold. Industrial minerals producers may sell brand-name products to specific customers with exacting requirements, while metals producers often sell their fungible output on a faceless commodity market. Customer requirements are emphasized in WCM, and so the range of these requirements must be recognized. World-class manufacturing In any milling process, specific goals are set for product and process characteristics - concentrate grades, minimum daily throughput, moisture content, etc. WCM has two overriding objectives: the reduction of deviation from these standards, and the reduction of variability in all aspects of the process and product. By definition, reduction of deviation also includes minimizing plant downtime for repairs or process changes. WCM plants use just-in-time inventory practices and total quality control. WCM plants use these techniques to simultaneously improve productivity and reduce costs.

Jan 1, 1993

By Chapman Young, Donald E. McCarthy

Many hard rock tunneling projects, where the majority of excavation can be accomplished with TBMs, will still require considerable specialized excavation which can not be done with a TBM. This secondary excavation, involving cross cuts, galleries, flattening of the invert, increases in bore diameter, et cetera, may be accomplished with conventional drill and blast, applied on a small scale and usually with fracture control techniques, or with mechanical splitters. The problems of using explosives in many of these cases and the high cost of mechanical splitting excavation make the consideration of other approaches attractive. The PCF rock excavation method, which has recently been reduced to commercial practice for mine-development excavation, offers an attractive alternative to drill and blast and mechanical splitters. With the PCF method the rock is excavated utilizing a small-charge, propellant-driven, controlled, penetrating-cone fracture process. Excavation is carried out continuously by combining the PCF hardware with integrated mucking capabilities on a carrier which remains at the excavation point. In addition to the benefit of providing for complicated excavation geometry, the PCF method also causes minimal damage to the remaining rock which will significantly reduce ground support requirements. In very bad ground, the continuous nature of PCF excavation allows ground support to be applied as limited sections are exposed thus reducing both the duration and extent that the ground would be free to move. Data on PCF excavation parameters, as measured in actual mining operations, indicate that crosscuts, galleries and the like could be excavated at considerable cost savings compared to drill and blast or mechanical splitters.

Jan 1, 1995

By R. A. Pond

Two 6.17 m (20 ft 3 in.) diameter raises, concrete-lined to 5.49 m (18 ft) inside diameter, were completed in 1978 at the Monterey Coal Company Number One Mine near Carlinville, Illinois, by Frontier-Kemper Constructors. These two raises are the largest in cross-section yet completed by full-face upreaming, and the success of this project is expected to increase the application of raise-boring to coal mine shaft construction. WHY 6.17 M (20 FT) DIAMETER ? Raise boring is well accepted in the metal mining industry for a variety of applications, and is gaining in acceptance in the civil works construction industry. The use of raise boring to construct vertical openings for coal mines has not been as widely accepted, even though coal mining requires, per mine, the greatest number of openings to the surface of any underground activity. Several factors have influenced the low utilization of raise boring in coal mining: 1. Coal mine shafts must often be of large diameter to pass the required high volumes of ventilation air at acceptably low water gage pressures. Cross-sectional areas of finished shafts exceeding 23.23 sq m (250 sq ft) are common. 2. The life of ventilation shafts is comparatively long, and the typical sedimentary strata overlying coal seams normally require that the shafts be lined. Shafts on the intake ventilation circuit must have permanent water-tight linings. 3. Unconsolidated overburden at the surface is often thick, and as reaming cannot be safely utilized in unconsolidated material,

Jan 1, 1979

By Allan T. Fisk, Carl R. Peterson, Robert G. Lundquist

A long recognized goal in high speed tunneling and mining has been the development of a continuous drill and blast excavation capability. Both the advance rate and the economy of drill and blast tunneling can be significantly improved if the conventional cyclic process can be carried out continuously. Obviously, any continuous drill and blast tunneling machine must be an "all function" device, performing drilling, explosive loading, initiation, mucking, ventilation, roof support (if necessary), and perhaps other functions, essentially simultaneously, while remaining at the face throughout. Furthermore, such a machine must do all these things under remote control. THE SPIRAL BLAST PATTERN Several continuous drill and blast tunneling concepts have been proposed. Of these the Rapidex spiral blast pattern, taking advantage of a partially self-shielding geometry, seems to require the least shielding and hence offers the maximum access for mucking, although from the outset it was clear that remote mucking would present a major design challenge. The Rapidex continuous spiral blast concept uses an unusual blasting pattern that, under the geological conditions tested, has proven to be an effective and efficient means of fragmentation. The concept has a self-shielding characteristic which permits a lightly shielded machine to remain at the face during blasting. The pattern produces a spirally proceeding tunnel face, much like one turn of an auger. The leading portion of the spiral surface is connected to the trailing portion by an axially extending plane surface or bench. The ideal geometry is illustrated in Figure 1 for a horseshoe tunnel section.

Jan 1, 1979

By Susan T. Bagley, Linda D. Gratz, Kirby J. Baumgard

The extensive use of heavy-duty diesel engines in underground mines has raised concerns about the potential adverse health effects to miners exposed to diesel particulate matter (DPM) which contains mutagenic and carcinogenic organic compounds. The purpose of this study was to compare the levels of DPM, biological activity, and polynuclear aromatic hydrocarbons (PAH) attributable to diesel engines in underground coal mines and similar data collected in engine laboratory facilities to assess whether laboratory data could be used to predict in-mine levels of diesel emissions. Mean in-mine DPM and SOF concentrations varied from 0.90 to 1.9 mg/m3 and 0.08 to 0.40 mg/m3, respectively. DPM-associated mutagenicity (mean) levels at two of the mines varied from 400 to 970 revertants/m3. Concentations of three PAH differed by up to four-fold between two of the mines, largely reflecting differences in DPM and SOF levels. The laboratory raw exhaust data were divided by 100 to obtain expected or predicted values for in-mine concentrations. The predicted DPM, SOF, mutagenicity, and PAH values based on laboratory samples were not significantly different from many of the in-mine values. Using a potential in-mine dilution ratio range of 20 to 200:1, virtually all in-mine data fell within the predicted range. Therefore, an estimate of in-mine concentrations can be determined by evaluating laboratory data. This will allow for extrapolations from laboratory tests with particulate emission control devices to assess potential health-related benefits due to their in-mine use.

Jan 1, 1991

By P. Hornby, S. Henley

INTRODUCTION The project described in this paper is designed to provide a standard and flexible method by which data can be exchanged among different systems and packages in common use for geo- logical modelling and mine planning, with substantial savings in ad hoc programming which is expensive and produces interface software that is difficult to maintain. Such packages include specialised applications such as Vulcan, Surpac, Datamine, and Gemcom software, and the Whittle pit optimisation programs, and more general products such as AutoCad, Microstation, and Maplnfo, and database management systems through a generic SQL interface. The data translator is built around the CSIRO Data Model and GeoEditor, and will make widely available the benefits of the Data Model by adding functionality to its implementation in an industry- standard language and style, with interfaces to important geological and mining software products used by the industry, while including also the visualisation and editing capabilities of the GeoEditor which provides the functional framework within which the Data Translator is developed. The Data Translator is intelligent in the sense that it is not a black-box solution but allows visualisation and validation of data during transfer; furthermore it provides a means for changing abstraction levels during the transfer operation. There have been few similar efforts to address this problem. It is not a problem which is likely to be solved in any general or long- term way by any individual commercial software vendor. THE CSIRO DATA MODEL A wide variety of software tools have entered the exploration and mining industries via different pathways. Examination of these pathways and the origins of the software illuminates the types of data transfer problems and difficulties which might occur in the day to day life of exploration and mining operations. In exploration, the focus is normally on a large area (>5000km2) which is explored primarily in two dimensions. For 20 exploration purposes, geographical information systems (GIs) software, image processing software, and, in some cases, 20 computer aided design (CAD) software have been employed. Typically, GIs soft- ware is used the most by lands and tenements personnel and government geological survey organisations, image processing software is used the most by geophysicists, and 20 CAD software is used the most by drafting and geology personnel. In contrast, within the mining environment, almost all activities have 3D character. In this realm, 3D CAD software and specialised mine planning and design software are important. Specialised mine planning and design software is similar to 30 CAD software, but typically has additional capabilities such as specialised modules for surveying, drill hole data operations, open pit design and optimisation, underground mine design, mining block model creation, and/or ore reserve calculations. Unfortunately, the different origins of the software in exploration and mining lead directly to problems in data exchange and the design of seamless software systems. These problems result from the different data management strategies employed by the different classes of software. In order to address these problems, CSIRO Exploration and Mining and CSIRO Division of Information Technology have been investigating the structure, character, and syntax of data and soft- ware present in computer-aided exploration and mining activities since early 1993. The goal of this effort is to 1) systematically ex- amine the breadth and depth of the data in use within exploration and mining, and to 2) promote a data organisation strategy which is broad enough and comprehensive enough to enable wiser soft- ware design and easier data transfer. In the short term a data model can be used to improve data transfer; in the longer term it is hoped that a data model framework will help object-oriented concepts to enter the next generation of geoscientific software. The data model is described in more detail by Power et al., 1995. THE DATA TRANSLATOR PROJECT The CSIRO Data Model provides a basis for a very wide range of applications in geology and mining. It has been developed over the past two years by a joint team from the Division of Exploration and Mining and the Division of Information Technology, and its principal purpose is to provide a comprehensive and self consistent model of the geometric and topological properties of geological and mining data. The project is being carried out by CSIRO with the support of Australian mining companies through AMIRA (the Australian Mining Industries Research Association). Eight companies are sup- porting the project : • North Ltd Minenco • MIM Exploration • Fractal Graphics • BHP Australia Coal • Pacific Coal • Gencor CRA Exploration The systems to be interfaced have been decided by comparing the priorities of the various sponsors, to produce a final combined priority list as follows : • Vulcan • Minescape • Micromine • Mapinfo INTRODUCTION The project described in this paper is designed to provide a standard and flexible method by which data can be exchanged among different systems and packages in common use for geo- logical modelling and mine planning, with substantial savings in ad hoc programming which is expensive and produces interface software that is difficult to maintain. Such packages include specialised applications such as Vulcan, Surpac, Datamine, and Gemcom software, and the Whittle pit optimisation programs, and more general products such as AutoCad, Microstation, and Maplnfo, and database management systems through a generic SQL interface. The data translator is built around the CSIRO Data Model and GeoEditor, and will make widely available the benefits of the Data Model by adding functionality to its implementation in an industry- standard language and style, with interfaces to important geological and mining software products used by the industry, while including also the visualisation and editing capabilities of the GeoEditor which provides the functional framework within which the Data Translator is developed. The Data Translator is intelligent in the sense that it is not a black-box solution but allows visualisation and validation of data during transfer; furthermore it provides a means for changing abstraction levels during the transfer operation. There have been few similar efforts to address this problem. It is not a problem which is likely to be solved in any general or long- term way by any individual commercial software vendor. THE CSIRO DATA MODEL A wide variety of software tools have entered the exploration and mining industries via different pathways. Examination of these pathways and the origins of the software illuminates the types of data transfer problems and difficulties which might occur in the day to day life of exploration and mining operations. In exploration, the focus is normally on a large area (>5000km2) which is explored primarily in two dimensions. For 20 exploration purposes, geographical information systems (GIs) software, image processing software, and, in some cases, 20 computer aided design (CAD) software have been employed. Typically, GIs soft- ware is used the most by lands and tenements personnel and government geological survey organisations, image processing software is used the most by geophysicists, and 20 CAD software is used the most by drafting and geology personnel. In contrast, within the mining environment, almost all activities have 3D character. In this realm, 3D CAD software and specialised mine planning and design software are important. Specialised mine planning and design software is similar to 30 CAD software, but typically has additional capabilities such as specialised modules for surveying, drill hole data operations, open pit design and optimisation, underground mine design, mining block model creation, and/or ore reserve calculations. Unfortunately, the different origins of the software in exploration and mining lead directly to problems in data exchange and the design of seamless software systems. These problems result from the different data management strategies employed by the different classes of software. In order to address these problems, CSIRO Exploration and Mining and CSIRO Division of Information Technology have been investigating the structure, character, and syntax of data and soft- ware present in computer-aided exploration and mining activities since early 1993. The goal of this effort is to 1) systematically ex- amine the breadth and depth of the data in use within exploration and mining, and to 2) promote a data organisation strategy which is broad enough and comprehensive enough to enable wiser soft- ware design and easier data transfer. In the short term a data model can be used to improve data transfer; in the longer term it is hoped that a data model framework will help object-oriented concepts to enter the next generation of geoscientific software. The data model is described in more detail by Power et al., 1995. THE DATA TRANSLATOR PROJECT The CSIRO Data Model provides a basis for a very wide range of applications in geology and mining. It has been developed over the past two years by a joint team from the Division of Exploration and Mining and the Division of Information Technology, and its principal purpose is to provide a comprehensive and self consistent model of the geometric and topological properties of geological and mining data. The project is being carried out by CSIRO with the support of Australian mining companies through AMIRA (the Australian Mining Industries Research Association). Eight companies are sup- porting the project : • North Ltd Minenco • MIM Exploration • Fractal Graphics • BHP Australia Coal • Pacific Coal • Gencor CRA Exploration The systems to be interfaced have been decided by comparing the priorities of the various sponsors, to produce a final combined priority list as follows : • Vulcan • Minescape • Micromine • Mapinfo • Medsystem

Jan 1, 1996

By J. R. Johanson

Many solids processes that look feasible on paper or even in pilot studies become disasters in full scale. Changes in solids flow characteristics from pilot scale to full scale because of larger so lids contact pressures, thermal shocks or unforeseen temperature excursions often cause full scale solids flow problems not encountered in the laboratory or pilot studies. Fortunately, proper applications of solids flow principals and solids flow property measurement at full scale conditions can anticipate the problems and thus provide an accurate basis for full scale design or existing plant modifications.

Jan 1, 1988

By James P. Sabogal

A control and monitoring system is being developed by Betz Laboratories for the heap leach process in gold recovery. Called Betz 14000GL, the system is designed to improve gold leaching and provide savings in chemical consumption by controlling and monitoring key parameters in the heap leach gold recovery circuit. The system uses information from on-line sensors to control antiscalant chemical addition, pH and cyanide levels. The proprietary graphics and report features of the computer system allows the user to monitor and critically evaluate the performance of the process.

Jan 1, 1998