Search Documents

By Viggo C. Bertelsen, David G. Hammond

LOCATION AND EXTENT OF BART TUNNELS The San Francisco Bay Area Rapid Transit District (BART) during the past six years has become the Owner of 23.5 miles of single-bore tunnels. The tunneling experience gained while working closely with our Engineer and Contractors in the design and construction of these major transit facilities provides a basis for our "Owners" viewpoint. The 23.5 miles of tunnels are divided into two categories. Fifteen and one-half (15-1/2) miles of tunnels were constructed in soft ground underlaying the downtown areas of San Francisco, Oakland and Berkeley. Eight (8) miles of tunnels were built in "hard ground" in the hills separating Oakland and Berkeley from Contra Costa County and in the San Francisco hills on the Mission Line. Location of tunnels within the BART system are shown on Figure 1. The tunnels comprise 15.7% of BART's 75-mile dual track system. Their 176 million dollar costs (excluding rail, electrification or ventilation features) are 12.4% of the system's total estimated cost of $1.4 billion. The tunnels constructed in soft ground were shield and boring machine driven with ground support provided by steel liner rings. The exterior diameter is 17 foot, 6 inches in the majority of tunnels; however, on two tunnels with a 500 foot radius of curvature, the diameter was 18 feet. BART awarded 14 contracts for soft ground tunneling. The work was accomplished under free air or compressed air depending upon the ground water and soil conditions, safety requirements, and considerations for protecting adjoining property from damage either from the de-watering operations or settlements due to excavation. The tunnel bores, except on curves, were normally parallel being spaced at 32 foot centers on the Mission

Jan 1, 1997

By A. C. Lyons, A. J. Reed

INTRODUCTION A trend which is obvious in the United Kingdom and is thought to be evident in other parts of the Western world is the disproportionate rise in the cost of tunnel mining labour compared with other tunnel cost increases. This disproportionate increase in labour costs has been accompanied by, and may be the result of, a shortage of skilled working labour. To combat this problem there has been a steady increase in the use of machines for excavation and for the erection of tunnel linings to keep the amount of skilled labour working below ground to a minimum. The typical tunnelling cycle, where the ground needs continuous support can be excavation, temporary support, temporary lining, grouting and permanent lining. It is obviously an advantage to combine as many of these operations as possible and carry out as much as possible by machine. Machines have been developed which will, either alone or used in combination with a shield, excavate and, when necessary, temporarily support the excavation. If a segmental lining is used, it can be so designed that it will form the permanent lining and reduce the cycle time and skilled labour requirement to a minimum. In cases in which the ground can be cut accurately to a smooth profile and will stand without support for a sufficient time, the lining can be expanded against the ground and the necessity of grouting eliminated. In cases in which ground will not stand without support, the usual method is to use a bolted lining and to grout behind it preferably as the shield is shoved forward. Whichever technique is used (this is largely determined by the ground) it is an advantage to make the segments as large

Jan 1, 1974

By D. C. Torre

Ever since the introduction of the first successful continuous mining machines some twenty odd years ago, there has been an obvious, and steadily increasing, need for some form of continuous haulage machine, or system to work with them. There is universal agreement that the continuous mining principle, and the various continuous mining machines in particular, have done a great deal for mining. However, coal mining men, who have the longest and broadest experience with them, agree that continuous miners do not truly mine continuously. In fact, their estimates, and actual studies, show that the real mining time of these machines ranges, on the average, from 20% or less to about 30% of the available shift time. Part of the failure of the continuous mining machine to mine continuously may be ascribed to breakdowns in its intricate machinery. Most of the failure, however, is blamed on a variety of other factors. Of these, there are two which are given particular blame: face haulage and roof control. The relative importance of the two as the major negative factor in continuous mining is a moot point. However, there is an extensive concensus that haulage is the number one problem. Roof problems and their control are inhibiting factors regardless of the type of mining or mining machines employed. But the truth of the matter is that a continuous mining machine, like any type of loading machine, whether underground or on surface, is only capable of mining or producing in direct ratio to the mineable, or loadable, material that can be kept ahead of it and equally, if not more, important, that can be taken away from it. While the first commercially successful continuous miners were developed for, and proved successful in, coal mining, they were soon

Jan 1, 1974

By R. Gong, R. Bhaskar

[Full-scale laboratory experiments were performed to evaluate the effect of ventilation and water spray pressure on the potential dust capture efficiency of a ventilation system comprised of blowing ventilation and an underboon scrubber. The tests were performed for a 1.52-m (5-ft) roof height and 2.36 m-3/s (5000 cfm) blowing ventilation volume, and a 2.44-m (8-ft) roof height and 4.72 m3/s (10.000 cfm) blowing ventilation volume at three face positions of the miner. The scrubber suction rate was varied for the tests to study the effect of scrubber flow rate on capture efficiency. The airflow patterns and scrubber efficiency were determined by performing tracer gas tests. Tracer gas was released through a manifold placed in front of the rotating miner drum. The gas was sampled in a grid fashion using a real-time multi-point gas sampling system. The capture efficiency of the scrubber was evaluated based an the peak gas concentration of the gas laden air drawn through the scrubber and the amount of gas passing, through the scrubber as a fraction of the gas released at the face. The data were analyzed to yield scrubber peak concentrations, potential exposures at various operator locations and the gas removal percentage (GRP). The underboom scrubber appears to work best in the end sump position, relative to the start sump and start slab positions. The capture efficiency scrubber was higher for 2.44-m (8-ft) roof heights compared to 1.52-m (5-ft) roof heights. The data also showed that the scrubber air discharged behind the mining machine may be drawn into the face area by the action of the blowing ventilation system, resulting in recirculation.]

Jan 1, 1994

Because of the different types of reagents used for the flotation of sulfide and nonsulfide minerals, it is convenient to consider these two groups of ores separately. The metal sulfides and native metals are substantially all floatable with xanthate and similar collectors.

Jan 4, 1982

By D. Kruse, M. Sanaei

"3D finite element models of the Segmentally Lined Shaft (SLS) structure are simulated as means of numerical analyses of the system’s structural behavior. Top-down constructed rings, comprised of precast concrete segments, create a large diameter, relatively shallow underground space that can be utilized for various applications. To further investigate the effects of soil conditions and different loadings on the shaft structure, the FE model was run under various boundary conditions. Simulations include a) effects of various soil layers on the SLS, including a circumferential boundary of modified ground, b) effects of various soil layers on the SLS without any ground modification, c) Seismic analysis of the SLS with ground modification and d) Seismic analysis of the SLS without any ground modification. Comparing the analyses outcomes emphasizes the significance of the inclusion of the ground modification boundary in the structural performance of the SLS. INTRODUCTION TO SLS Underground structures are classically built rectangular in shape, which normally requires a two-step construction process beginning with installation of temporary shoring to support earth loads during the excavation, followed by the construction of the permanent structure. Attractive and practical alternatives are circular shafts referred to as segmentally lined shafts (SLS). The structure consists of a stacked series of rings formed from an assemblage of precast concrete segments. Top-down constructed systems of large diameter, relatively shallow SLS structures provide both temporary earth support during excavation and permanent structural support for many civil and building applications. The circular shafts sustain the lateral earth pressure mainly through hoop-stress mechanism, resulting in improved stability and structural efficiency. Cylindrical shell structures with large diameter to wall thickness ratios are prone to buckling under external pressure. In typical designs of small diameter shafts and tunnel linings with small diameter to wall thickness ratios, nonlinear buckling analysis (i.e., nonlinear geometric analysis) is usually not considered, since the buckling capacities for those structures are much higher than typical pressures encountered at their design depths. With an economically viable wall thickness, buckling becomes a critical issue, which should be addressed, for circular shafts with very large diameters. In the design and construction of the SLS, the stability of the structure can be improved by modifying the soil surrounding the circumference of the shaft to a limited thickness and to about 10 ft below the finished shaft structure. This thick wall of soil mixed with cement creates a composite integrated structure while serving additional purposes such as ground control and ground water seepage cutoff."

Jan 1, 2016

Introduction One hundred years ago, a recent college graduate created the US aluminum industry. He found an economic way to crack the primeval bond that makes the metal so special. Aluminum doesn't "rust" - oxidize progressively. Rather, when exposed to air, it instantly forms a gem-hard but microscopic oxide coating. This seals off oxygen from the metal underneath. Scratch it and the seal reforms instantly. That tight chemical bond is the reason the metal is not found in nature; it exists only as a compound. The bond had to be broken to free the shiny metal. But once it is free, that self-sealing protection, alongside a remarkable strength-to-weight ratio, offers a marvelous material. Until 100 years ago, finding a way to do that economically was a challenge that defied science. Then it was solved, in a remarkable coincidence, on both sides of the Atlantic. And the way was paved for a material that would become the second most widely used metal in the world. Until that time, aluminum was a rare and precious metal. But then two young scientists independently invented the process that took aluminum outside the laboratory and into applications ranging from pots and pans to spacecraft. Discovery of aluminum Other major metals - copper, iron, lead, gold, and silver - had been used for thousands of years. But aluminum was entirely unknown until 1782, when French chemist Antoine Lavoisier suspected its presence. It was not actually discovered until Sir Humphry Davy, in England, detected it in clay in 1807. It was first isolated as a free metal only in 1825, by Denmark's Hans Christian Oersted. For years, laboratory methods yielded aluminum only in tiny amounts costing about $1200/kg ($545 per lb) - $13,333/kg ($6000 per lb) in today's dollars. Methods developed by French scientist Henri Sainte-Claire Deville in 1854 cut the cost to about $200/kg ($90 per lb). King Frederick VII of Denmark had a helmet of aluminum and gold. And Emperor Napoleon III of France reportedly served his most exalted guests at a state dinner with aluminum plates. He left the lower ranks to dine from pure gold. Deville and others continued to reduce production costs. But the price of aluminum still rivaled silver - $31/kg ($14 per lb) versus about $35/kg ($16 per lb) for silver. Then in 1884, a 2.8-kg (6.25-1b), 230-mm-tall (9-in.-tall) aluminum pyramid was cast as the tip of the Washington Monument. It was probably the first architectural use of aluminum. And it is still there after more than a century. The attractive properties of aluminum were obvious: it is lightweight but strong, conducts heat and electricity, reflects light and other electromagnetic radiation, and resists corrosion. But its commercial promise was blocked by its cost. In 1885, the price of aluminum was $17.70/kg ($8 per lb). It stayed there for the next couple of years until the Hall-Heroult process brought it down sharply. Hall-Heroult process lowers aluminum costs The characteristic that kept aluminum hidden so long continued to thwart chemists. Aluminum clings to oxygen so tightly that it is never found as a free metal in nature, and it is hard to break that bond chemically. The best chemical methods of the 1880s required sodium, and sodium itself was expensive. At Oberlin College in Ohio, chemistry professor Frank Fanning Jewett advised his students that anyone who could make aluminum inexpensive would do humanity a favor and get rich as well.

Jan 3, 1987

By James W. White

From Modular's first truck-dispatching system for Phelps Dodge Corporation in 1979 to today's alliance between Modular and Komatsu, Ltd., innovation has been Modular's main product. This paper describes the growth of a mining products supplier and the philosophy and decisions behind that growth.

Jan 1, 1998

By Gordon P. Riddler

IMMM Reporting Code 2001 – Some Developments -General definition of a Competent Person -Rules of Conduct with Guidelines -Table of Generic Terms with Guidelines -More specific to non-metallic minerals -Word ‘ore’ is not used for reserve/resource categories -More definitive on Mineral Exploration Results

Jan 1, 2003

By S. J. Chadwick

The majority of small gold plants constructed around Western Australia were designed for short lives and treatment of oxide ores. The crushing plant frequently bore the brunt of capital cost savings resulting in inadequate design and equipment selection. The exhaustion of oxides and progressionto more competent ores is _ resulting in plant operators seeing their he majority of small gold plants constructed around Western Australia were designed for short lives and treatment of The net result of many of extended operating hours, low inability to achieve fine mill blow out in operating costs, the above is throughput, feeds and a oxide ores. The crushing plant frequently bore the brunt of capital cost savings resulting in inadequate design and equipment selection. The exhaustion of oxides and progression to more competent ores is resulting in plant operators seeing their operating costs spiral upwards. Steps taken at Jubilee mine to improve plant productivity and lower mechanical failure will be discussed. operating costs spiral upwards. Steps taken at Jubilee mine to improve plant productivity and

Jan 1, 1991

By Jim McMaster, Charles W. Kenney

The role of oxygen in cyanide leaching ia well understood in the gold industry. Oxygen enrichment has taken on a real, practical meaning to operators with the were to evaluate the effect of oxygen enrichment on the kinetics of heap leaching gold ores, to examine methods of oxygen application in the heap, and to develop preliminary economics for the process. Several series of column tests were completed increasing preaeration, applications. use of pure oxygen for leaching, and in CIL in the test program. Oxygen enrichment may have a significant place in heap leaching as well. In preliminary column tests sponsored by Kamyr at Hazen Research, Inc. , oxygen-purged columns showed an increase in both the leaching rate and maximum recovery of gold and a reduction in cyanide consumption compared to columns run with air. Potential benefits of using oxygen in heap leaching include faster leaching kinetics, shorter cycle time, higher recoveries, and more efficient use of permanent or reusable pad space. The concept requires confirmation of technical and economic feasibility on a commercial scale.

Jan 1, 1990

By Sean E. Armstrong, Deepak Malhotra

The current trend in gold ore processing is the development of lower grade or highly refractory deposits. The perplexity of treating low grade oxidized ores has been adequately addressed by heap leach technology. However, refractory gold ores are very difficult to positively characterize the gold association within the mineral matrix. Gold accompanied with refractory sulfitlc or carbonaceous mineralization can often be sub­micron In size and occur interstitially. Mineralogical examination of these ores Is difficult, expensive, and occasionally Inconclusive. Hence, the metallurgist Is given little information for the selection of processing alternatives. The purpose of this paper Is to demonstrate the use of diagnostic leach procedures to assist the metallurgist' s decision-making process to solve some of these problems. By sequentially liberating and/or leaching gold associated with specific minerals, the amount of recoverable gold in each stage can be determined. Through careful interpretation of the results obtained by diagnostic leaching, the metallurgist can devise a flowsheet for treating the ore or solve a problem at an existing plant

Jan 1, 1992

By Stuart K. Nicol, Malcolm D. Engel, Neville T. Moxon

Ion flotatir,n of gold is a process being developed to selectively float extremely dilute aurocyanide liquors using a novel surface active complexing agent. The principle of ion flotation is also applicable to a wide range of other metal-containing solutions. The market potential of the gold flotation process would be enhanced by the possible combination of the gold recovery capabilities with both cyanide recovery and metal removal. For example, recovery of copper cyanides from a return liquid strean1 would be a useful means of reducing operating costs and satisfying environmental pressures to treat tailings dams. Experimental work is described where samples of tailings solution from a far north Queensland gold mine were subjected to ion flotation to remove copper cyanide species from a clear recycle solution. The form in which these products was removed was of secondary importance compared to the need to produce a clean solution for use in the plant. Recovery of the anionic copper cyanide species was accomplished using a quaternary ammonium surfactant.

Jan 1, 1991

By Chris Campbell-Hicks

Methods used for assay of gold values in resource estimation, grade control or downstream processing are based almost entire­ly on Fire assay or Aqua Regia techniques. Both these tech­niques frequently produce spurious results. The mechanism of error is explained. Major decisions are made based on this often flawed data. This is what our operating budgets and projected cash flows are based on. Project economics demands metallur­gical accountability for performance predicted. Accountants and more astute members of the board are often not sympathetic to gold out-tum from plant production which is occasionally or consistently less than that predicted. Equally importantly, better than budgeted gold out-tum, resulting from under assaying will produce reconciliation or accounting problems (surplus cash flow) often denying correct timing of expansion or acquisition. Both these scenarios can be avoided if 'real world' extractable gold values are presented to financial managers at all stages. Such extractable gold results are now possible, and compared to fire assay and aqua regia, the assays are faster, cheaper, simpler and more accurate.

Jan 1, 1996

By V. I. Lakshmanan, Chris Dodson

Refractory gold ores or concentrates are pretreated in general by physical, chemical and biological oxidative pretreatment processes prior to cyanidation for the economic recovery of gold. The thermal treatment processes generally include fluid bed pro­cessing(!>, chemical with pressure<') or atmospheric (Caro's< ·'>, 3 Nitrox1')) pretreatment leaching and physical with ultrafine grinding!"). Roasting and aqueous pressure oxidation pretreat­ment methods have several commercial applications (Homestake, Barrick) and biological oxidation methods have recently found industrial applications in Africa. The roast pretreatment methods to treat refractory sulphide ores or concentrates transform iron sulphides generally to a porous iron oxide matrix assisting the lixiviant cyanide to effectively diffuse the calcine for cyanidation and hence with improved gold recovery. Jha and Kramer<') made an extensive review of roasting chemistty and practice to tt·eat refract01y gold ores. Industrially two stage pretreatment roasting is generally employed. During the first stage roasting is carried out under oxygen deficiency conditions to provide a low arsenic calcine, mainly magnetite and in the second stage magnetite is trans­formed to haematite under oxidizing conditions.

Jan 1, 1998

By David Lunt, Evan Kirby, Peter Mason, Ian Ritchie

The treatment of refractory gold ores, in particular the "competing" technologies and their relative advantages and economics, has become a major segment of most mineral technology oriented conferences in recent years. A common theme is the increasing refractory nature of gold ores being treated. This is despite ores such as those at Kalgoorlie having required roasting for liberation since the last century. Papers on refractory gold treatment have examined the characteristics of refractory ores and the causes of reduced recovery (eg La Brooy 1994), the available technologies and their relative economics eg Litz 1990), and the selection of a suitable process route (eg Nicholson 1993, Weston 1994). The most comprehensive collation of data on such processes is provided in the different editions of Randol. A variety of classifications and definitions of "refractory ore" have been published. Due to the many factors which can impact on the recovery of gold it is perhaps not feasible to develop a universal characterisation that can be applied to all gold bearing rocks. La Brooy et al have provided the framework for characterisation shown in figure 1.

Jan 1, 1995

By A. Anderson, G. May, C. Kubank, S. Meik

The Kori Kollo operation is owned by Empresa Minera Inti Raymi S.A., a Bolivian mining company. Inti Raymi is an eighty-five percent owned subsidiary of Battle Mountain Gold Company (BMGC). The remainder of Inti Raymi is held by Zeland Mines S.A., a Bolivian mining company. The project is located near the village of La Joya, approximately 220 km south of La Paz, and 40 km north west of Oruro on the Bolivian altiplano. Inti Raymi started a heap leach operation in 1985. By 1988, following several expansions, 4,000 tonnes per day of oxide ore were being treated. At this time drilling was started to delineate the larger sulfide orebody. A feasibility study for the development of this deposit was completed in 1990, and following project approval, the engineering design was started later that year. During this period orders were placed for the major items of mechanical equipment. In July 1991, Minproc Engineers Inc. was awarded a firm price contract to design and construct the 14,000 tonne per day sulfide ore process facility.

Jan 1, 1993

By M. Kavvadas

Geotechnical design using Factors of Safety recommended by Codes of Practice is based on largely unknown ?margins of safety?, usually without consideration for the importance of the project (i.e., potential consequences of failure) directly or explicitly. On the contrary, probabilistic modelling can be a useful tool in risk management as it provides the means to measure the risk to be managed. This is achieved by calculating the probability of failure associated with a specific design, i.e., by relating the classical factors of safety with the corresponding probability of failure and by using a cost optimization procedure to achieve ?optimal? designs, accounting for the expected costs in case of catastrophic failure. This paper describes the methods used to calculate the probability of failure and its correlation with the classical Factor of Safety using sampling techniques and a simplified method based on the moments of the factor of safety considered as a random variable. These procedures are illustrated in an example which investigates the stability of a slope.

Jan 1, 2005

At present, increasing focus of public perception is placed on the environmental and social benefits, risks and impacts of metals and metal-bearing products. To address these issues, the concept of product stewardship has recently been introduced into the political debate. In this paper, results from a survey of existing environmental and social reporting practice in the copper mining, smelting, refining and fabricating industry are presented. In this context, particular emphasis is placed on the reporting practice regarding products and product performance over the life cycle. In a few companies there has recently been a shift towards adopting product stewardship principles and putting them into action. As part of an ongoing exercise within the Non-Ferrous Consultative Forum on Sustainable Development sponsored by the International Copper Study Group (ICSG) key issues of interest to the non-ferrous metals sector are being addressed. The Forum, for example, has developed a series of principles, criteria and indicators that could form the basis for a voluntary, industry-lead product stewardship scheme. Current achievements and way forward of this product stewardship initiative will be presented.

Jan 1, 2003

By Suresh K. Bhatt

Appalachian coalfields have been the predominant source of quality coals since the inception of commercial mining in the United States. In a broad sense, Appalachian coalfields can be considered those east of the Mississippi River, representing about 55% of total US coal production. In this special feature on Appalachia in MINING ENGINEERING, emphasis is given to the four coal-producing states of Pennsylvania, West Virginia, Virginia and (eastern) Kentucky. These four states produce more than 90% of the coal from the total Appalachian region, or about 40% of the total US coal production. Historically, Appalachia has been the principal source of coal for domestic industries and for export. There have been numerous fluctuations in the Appalachian coal industry during the past 20 years. Appalachia was affected by cyclical and structural changes in various industries, particularly the US steel industry, and changing world coal markets. It was also the region of more mine worker labor stoppages than other parts of the country. In general, the factors that affected Appalachian coal production over time are identical to those that determined changes in coal production nationally.

Jan 1, 1995