Search Documents

By Y. Ye, J. D. Miller

Certain bituminous coals are known to contain appreciable quantities of natural fossil or subfossil resin. Such resinous coals are found in the western US, particularly the Wasatch Plateau coalfield of UT. Some of the seams in this field contain an average of 5% resin. This fossil resin has been recovered by gravity and/or flotation processes since 1929. Resin concentrates thus produced are of low quality and are usually refined by solvent extraction. The purified resins are of commercial importance in the adhesive, coating, rubber. and ink industries, etc. An improved flotation technique has been developed which involves ozone conditioning to selectively float resin from high-volatile bituminous coal. With this flotation process, a concentrate product which contains 95%

Jan 1, 1990

By Francis W. Brown, Philip R. Hunt, Douglas N. Halbe

Refractory arsenopyrite ore from Western Mining Corporation's Lancefield deposit in Western Australia is treated by fluosolids roasting of a flotation concentrate followed by cyanidation of calcine and flotation tailings. The project development is reviewed from original testwork through circuit design, operating experience, and subsequent expansion.

Jan 1, 1990

By Bill Sayer

Cadman, a wholly owned subsidiary of Heidelberg Cement, is a leading supplier of sand and gravel as well as ready mix concrete in the greater Seattle area in western Washington State. Cadman's aggregate mine is located in North Bend, 34 miles east of Seattle, WA, and consists of a "Lower Pit" and an "Upper Pit." In 2005, Cadman planned the upgrade of the North Bend mine operation as follows: Upper Pit (Figure 1): 1. Crushing Plant, Stacker and Stockpile 2. Storage Reclaim Belt Feeders 3. Feed Conveyor 4. Downhill Overland Conveyor Lower Pit (Figure 2, Photo 12): 1. Radial Stacker 2. Storage Reclaim and Truck Load-out

Jan 1, 2008

By Richard R. Klimpel

This article introduces the basic definitions and philosophy behind process hazard evaluation procedures and the determination of risk as being a function of accident probabi1ity and accident consequence. The general concepts of good engineering practice and predictive hazard evaluation are discussed. The most commonly employed methods used in the processing industries are reviewed with an eye towards briefly presenting what each method offers as far as information, time and resources required, etc. Some initial references on the actual practical use of each technique in the processing industries are also given.

Jan 1, 1991

By Meliton M. Garcia, Satya Harpalani

The volume of gases produced in major and trace amounts as a result of detonation of explosives in an underground mine was determined. The volumes of major gases (CO, CO2, NO and N02) were measured immediately following detonation, during the mucking operation, and following the removal of muck. Tests to identify and quantify the gases produced in trace amounts were performed following the detonation only. The composition of the gases produced varied significantly depending on the composition of the explosive/blasting agent. An average of 95% of the gases produced were found in the test chamber immediately following the detonation, while 2% was found in the chamber following the removal of the muck. Several compounds were identified in trace amounts. Of particular interest was the detection of benzene, toluene, butenes, ethyl benzene and naphthalene since exposure to some of these compounds, even in trace amounts, could present a serious health hazard.

Jan 1, 1987

By Y. Topkaya, R. E. Johnson, B. R. Palmer, R. B. Bhappu, J. Brent Hiskey, Gürses Öner

Currently there is considerable interest in applying in situ leaching technology to recover copper from oxide ores. In many instances, the distribution of copper mineralization in these deposits is fracture controlled. Laboratory core-leaching experiments have demonstrated that leaching response is sensitive to the dissolution of copper from and the formation of channels along main fractures. Solution short- circuiting can be a major limitation of this technology. This paper describes the application of macromolecular polymers to achieve flow-profile control during leaching. Pre- and post-leached fractures were characterized by computerized tomography (CT) analysis.

Jan 1, 1993

By J. J. Moore, I. Iwasaki, L. A. Lindeke

Correlation of scale-up from small-scale batch laboratory mills to large-diameter industrial mills was established by performing two series of laboratory and pilot plant grinding tests using a magnetic taconite ore and a siliceous sulfide ore. In one series, controlled batch grinding tests in 203-, 508-, and 914-mm (8-, 20-, and 36-in.) diameter mills were carried out followed by a second series involving continuous grinding tests using 305-mm (12-in.) and then 1067-mm (42-in.) diameter pilot plant ball mills in open circuits. The effects of ball diameter on wear and of mill diameter on grinding power and ball wear are illustrated.

Jan 1, 1988

By D. T. Kinard, A. A. Schweizer

An operational 9 meter (30-foot) high gold heap leach pile was investigated by excavating test pits up to 6 meters (20 feet) deep, obtaining bulk and relatively undisturbed thin wall drive samples, and observing the ore distribution patterns exposed in the test pit walls. The clayey ore is crushed, agglomerated with lime and cement, and deposited on the leach pads using a radial stacker. Laboratory tests performed included moisture-density, gradation, compaction, Atterberg limits, permeability (constant and falling head), and triaxial strength tests. Discussion is presented on the effects of agglomeration on the permeability and strength characteristics of the in-place ore. Also discussed is the effect of deposition of the ore using the radial stacker.

Jan 1, 1987

By Lars Lövgren, Jörgen Jönsson

Heavy metals may be retained within deposits of sulfide minerals under oxidation and in the nearest recipients of drainage water by sorption to secondary iron precipitates. The extent of sorption is strongly influenced by solution pH and presence of complexing ligands, such as sulfate and natural organic acids. Desorption of metals and organidinorganic anions to recent secondary Fe precipitates, collected at the Kristineberg mine, Sweden, has been investigated under different geochemical conditions. Elemental composition and structural characterization (X-ray powder diffraction) indicate presence of schwertmannite. While metals such as Ni and Pb were fractionally desorbed from the precipitates under acidic conditions, oxyanions, e.g. arsenatdarsenite and sulfate were desorbed preferably under alkaline conditions. In a separate study the adsorption of NOM onto synthetic goethite was investigated. NOM adsorption showed a strong pH dependence, 95% was adsorbed at pH 3 and 40 % was adsorbed at pH 9. Addition of 2 mM of sulfate desorbed about 10 % of the adsorbed NOM.

Jan 1, 2000

By J. Bartrum, A. Bowler, G. Butcher

The purpose of this paper is to outline the design, specification, and operation of the 8.5-m- diam (28-ft-diam) SAG mill commissioned at Kidston Gold Mines during January 1985. Amenability of Kidston ore to SAG milling, coupled with substantial cost advantages, led to the specification of this mill, equipped with variable speed drive to overcome the large variation in ore hardness. Operation of the mill is effected via a number of automatic control loops. Problems experienced with automatic control plus other electrical and mechanical failures have led to design changes and the formulation of future operating strategies.

Jan 1, 1987

By John Matthews

During 1982 and 1983, it became increasingly clear that North River No. 1 Mine would have to buy a set of replacement longwall shields. Despite extensive efforts to make improvements, the shields that were in place at that time were incapable of holding the roof. North River Energy had limited experience in specifying and acquiring longwall roof supports, but a great deal of experience with our conditions and needs. We there- fore compiled a shield evaluation method that uniquely responded to our situation. The resulting system emphasized teamwork among operating, maintenance and engineering personnel. The charge from management was threefold: select shields to support maximum expected loads, optimize face operations, and pay attention to detail. Final selection was made objectively, based on all available information. We chose a 5516 KN (620 tons) support with a minimum yield load density of 760 KN/m2 (7.9 tons/ft2). This paper reviews our process of specification, design, prototype testing, and fabrication, and offers some relevant suggestions.

Jan 1, 1986

By D. R. Maneval

The vast coal resources of North Slope, Alaska, can be expected to attract substantial interest because the nearly flat-lying coal beds of the coastal plain are specially amenable to surface mining. Mining on a scale large enough to justify coal development in this area could have severe environmental effects. The mitigation would be uncertain because large-scale coal mining and reclamation operations have not been carried out in the arctic. The deficiency of the scientific data base is another factor that requires consideration if coal mining has to develop in accordance with the objectives of PL 95-87. The objective of this paper is to establish the inter-relationship between the problems due to permafrost and factors in reclamation of post-mining land in order to find ways to transform nature in a rational and purposeful manner and to suggest specific reclamation approaches that may be appropriate in this region.

Jan 1, 1987

By S. R. Bryan, J. D. Stephens, D. R. Rothbard

The distributions of gold and associated elements in mineral grains from a pyritic gold ore were studied by optical microscopy, and by SEM and SIMS imagery. Products studied were a sulfide flotation concentrate, a calcined sulfide concentrate, a cyanide leached calcine, and a cyanide leached pressure oxidation residue. Individual pyrite grains are compositionally zoned and solid solution gold occurs in some, but not all zones. Most of the gold in calcined products is present as metallic coalesced grains that are smaller than 100 angstroms. Gold lost into cyanide leached residues from the calcines tends to be in “semi-dense” grains that cannot be distinguished from gold-free grains except by SIMS analysis. The gold in cyanide leached pressure oxidation residues occurs as solid solution gold in unoxidized pyrite remnants.

Jan 1, 1990

By Gregory A. Hope, Kym Watling, Matthew I. Jeffrey, Ronald Woods

Surface enhanced Raman Spectroscopy carried out in real time has been applied to identify surface species formed during gold leaching in chloride and thiosulfate media. Chloride ion is adsorbed prior to the gold dissolution potential, but its coverage is significantly diminished at the beginning of leaching. A gold chloride band is again observed when dissolution is rapid, together with bands characteristic of AuC14- ions in solution. With thiosulfate, a thin gold sulfide layer is formed slowly in the potential region where leaching occurs. At higher potentials, thiosulfate is oxidized to sulfur and sulfate, both products being identified by Raman spectroscopy.

Jan 1, 2005

By Mark Kuchta, Hans Engberg

The Swedish mining company LKAB operates two of the largest underground mines in the world today that together produce around 35 Mton of iron ore per year. During the 1990s, the company embarked on a massive effort to computerize its mine planning system. The goal was to combine various mine planning operations including mine surveying, geologic modeling, mine layout, production planning, and production follow-up into one modular based integrated system. The system was built around a large Oracle database and the Microstation CAD system. This overall design strategy and the various system modules are described, and some experiences gained using the system are discussed.

Jan 1, 2002

By H. Y. Sohn, R. D. Hagni, M. K. Kojo

Reflected light microscopy was used to study the mineralogy and textures of experimental reactions of a nickel concentrate with a slag. Such an interaction is an important step in the bath smelting of nickel sulphide concentrate. Concentrate particles in the central portions of the pellets are rounded and develop vermicular S02 gas porosity. In the outer portions of the pellets, the original minerals of the concentrate, i.e., pyrrhotite, pentlandite, pyrite, chalcopyrite and violarite, have agglomerated and reacted to form two intergrown phases: pyrrhotite solid solution (FeO.75Ni0.18Cu0.01S) and pentlandite solid solution (Fe0.58Ni0.51Cu 0.03S). Magnetite formed euhedral crystals, skeletal crystals and dendrites at the margins of the matte. Prismatic, ferrohypersthene and octahedral Mg-Al-Fe spinet crystals and dendrites are present in the glassy slag. Key words: Nickel sulfide concentrate, Iron silicate slag, Bath smelting, Mineralogy, Microscopy

Jan 1, 2003

By F. F. Aplan

The material known as coal has a highly variable composition. As a consequence, coals show a great variation in their physical and chemical properties as a function of coal rank. The situation is further complicated because the preparation engineer must deal with raw coal, as mined. This is an assemblage of coal, upwards of 30% mineral matter and, typically, several percent pyrite. The kind and amount of the mineral constituents is also highly variable from source to source. A knowledge of coal rank and source location, and the kind and amount of associated impurities, is the first step in evaluating the response of a raw coal to preparation procedures. The raw coal must first be characterized before information from one source can be extrapolated to that of another.

Jan 1, 1988

By Michael J. Nicol

Hydrometallurgical processes involve the recovery of metals from ores, concentrates, calcines, mattes and scrap materials by a series of operations involving leaching or dissolution, separation, purification and reduction of metals in aqueous solutions. The underlying theoretical basis of many of these operations is electrochemical in nature and it is the purpose of this review to identify and illustrate, by way of examples from the author's experience and that of others, the central role of interfacial electrochemistry in the understanding, design and control of these operations.

Jan 1, 1993

By M. Balakrishnan, K. A. Natarajan, J. M. Modak, J. S. Gururaj Naik

The ability of various fungal species isolated from gold mines to uptake gold and base metals such as zinc, copper, iron and lead from gold-process cyanide effluents was investigated. Under identical treatment conditions, different strains showed wide variations in their ability to take up gold and other base metals. Aspergillus terreus exhibited as high as a 60% gold uptake. Almost complete removal of zinc was possible with various fungi and with the yeast Saccharomyces cerevisiae. Studies at various metal concentrations showed a higher gold uptake from dilute solutions, and studies with Aspergillus niger showed that gold uptake by living cells increased gradually as the contact time increased. Metal uptake capacities between living and nonliving cells were also compared. A waste biomass (ABM- I), obtained from a fermentation industry, wasalso identified as having a high gold uptake capacity. At 5% (W/v) solids, ABM-I could efficiently remove up to 83% of the gold contained in an effluent solution within 24 hrs.

Jan 1, 1995

By Wilson I. L. Lim, Jonathan J. Campbell, Luis A. Tondo

An important issue in the use of high pressure grinding rolls when grinding ores is wear of the rolls. Due to the abrasive nature of the ores, significant wear rates have typically occurred. Attempts to address the wear problem require a better understanding of the wear mechanisms. A probable wear mechanism is the abrasion of the rolls surface due to extrusion of the compacted material as it leaves the rolls. This paper presents the results of a study on a number of ores to examine the extent of extrusion that occurs. The study involved laboratory, pilot and full-scale high pressure grinding rolls. The effect of variations in parameters such as grinding pressure, rolls speed, initial gap settings, feed topsize and moisture was investigated. The results indicate that extrusion increases with increasing grinding pressure and rolls diameter, while the use of studded or profiled rolls significantly reduces the extrusion effect compared to smooth rolls. It was also found that rolls speed and feed moisture can have significant effect on extrusion, depending on the material.

Jan 1, 1998