Search Documents

By M. B. Mirza, W. A. Sadik, B. T. Stanley

This paper presents the ventilation design for an underground testing facility in a salt medium. The under-ground workings consist of two 3.6 m-diam (12 ft-diam) watertight shafts and about 1830 m (6000 ft) of drifting. These facilities are designed to provide access for an in situ testing of a salt horizon in which a variety of hazardous and nonhazardous materials could be temporarily stored or permanently deposited. The ventilation system includes a design basis for gassy mine conditions and provides for the option of bulk air cooling and heating.

Jan 1, 1987

By Keiichi Fujita, Katsumoto Ueda, Hiroshi Nakauchi, Naohiko Okumura

INTRODUCTION This paper presents (1) modified slipform system which was employed for simultaneous concrete placement for permanent lining and Instruction of a partition wall in the execution of a ventilation shaft 620m deep, and (2) current shaft sinking techniques which have been applicable and efficient for the subsurface conditions in Japan. MODIFIED SLIPFORM SYSTEM FOR PERMANENT LINING OF VERTICAL SHAFT General Information This paragraph deals with rapid construction by using modified slipform system for the permanent concrete lining and a partition wall of ventilation shaft, which has inside diameter of 620m and depth of 620m, of Enasan Highway Tunnel. The general feature of the shaft is illustrated in Fig. 1 and standard section of the shaft is illustrated in Fig. 2. The geological condition surrounding the shaft is mainly of ryolite and surface is of talus, but as a whole, they are rather weak and weathered rocks with faults, fissures and clay seams. 220mm borehole for the geological investigation was used as a drainage hole, predicting the amount of water inflow into the shaft to be 10t/min. The shaft was executed mainly by means of the conventional short step sinking method of 1.2m lift, employing temporary headframe and hoists. For each lift, 40 to 50cm thick temporary concrete lining was used. About 28,600m3 of rocks were excavated and

Jan 1, 1979

By J. A. Ryder

Compressed air is a relatively inefficient yet very convenient vehicle for transmitting mechanical energy. It is inefficient when compared to, say, hydraulic or electric energy systems since compressor and pneumatic machine efficiencies are quite low (in the range 20-65%) and reticulation losses can be quite high unless adequate pipe diameters are used to minimize friction drops. It is convenient in that capital and maintenance costs of pipes and machines are exceptionally low, the equipment is flexible and lightweight, the technological level is simple, the form of the energy supply is intrinsic- ally safe, and as an additional minor but psychologically important benefit, it provides a ready source of cooling and air supply for emergency use in deep hot mines. It is for these reasons that compressed air is a premier source of energy for many forms of underground equipment, in particular hand or rig-mounted rockdrills, some forms of rock- handling equipment, and a host of minor applications including agitators, small-lift pumps and temporary f am installations. In a typical S. African deep-level gold or platinum mine, compressed air generation accounts for 15% of the total mine electrical energy bill - more than is used for hoisting. In these mines it is not uncommon for over 100 km of underground compressed air piping to be installed, primarily to supply handheld rockdrills.

Jan 1, 1979

By Tony Treasure, Ian Ewart

The EMEW® cell has been developed to overcome a number of inherent limitations in conventional electrowinning technology, particularly the high cost and restricted process windows characteristic of conventional hardware. The EMEW technology has been widely demonstrated to achieve high performance for various metals under chemical conditions well outside the limits required for efficient operation of conventional cells. In particular application of the EMEW cell for recovery of silver offers significant operating and capital cost advantages over conventional Merrill Crowe technology used for cyanide based solutions. The cell also offers process advantages for direct silver recovery from nitric acid solutions. The performance of the EMEW® cell on silver cyanide solutions, producing high grade silver metal in a single step, is accomplished by providing a physical mechanism which presents metal ions to the cathode on a highly efficient and continuous basis. The simplicity of design and operation of the EMEW cell offers the following advantages for silver recovery from cyanide or nitrate based solutions: • High grade product in a single step. • Selective for silver over other metals in the electrolyte. • Wide operating concentration range (100,000 - 5ppm). • Ability of the cell to operated in a variety of acid or alkaline electrolytes. (Cyanide, Nitrate). • Simple liquor reticulation. • No pretreatment required - Clarification, deaeration or zinc dust. • High cmTent density and current efficiency compared to conventional electrowinning cell. • Modular design allows for flexible operation and production rate. • Pilot plant results using full scale cell result in accurate scale up design. • Easy/fast installation - cell banks are delivered pre configured with piping and wiring. • Enclosed cell minimizes corrosive vapor and liquid losses in the circuit.

Jan 1, 2000

By Malcolm J. Lake, P. Brad Marchant, Linda M. Broughton

Thiourea is recognized as a technically competitive alternative to cyanide for gold and silver extraction for a variety of ores and concentrates. This paper describes the results of a recent mini-pilot locked cycle test comparing cyanidation with acidothioureation treatment of gold bearing sulphide concentrate. The gold extractability of both methods was similar. The comparative metallurgical operating conditions and test results are summarized. Detailed byproduct solution analyses and environmental toxicity test results are presented and suggest that thioureation might result in acutely toxic byproducts even after treatment. Comparative process economics are summarized based on preliminary commercial operating flowsheets derived for the locked cycle case study. Capital and operating cost estimates are shown. The results indicate that cyanidation is more economically favorable within the constraints of the case study. Considerations for process selection between thioureation and cyanidation, for conceptual case studies, are discussed.

Jan 1, 1998

By V. Fred Swanson, J. Patrick Glynn

The environment for process engineers today is very different from 20 years ago. The ideas and mathematical description of models for a multitude of different unit operations is an ongoing development. The computer tools to deal with the mathematics are readily available and specialist companies have developed, tested and verified their models. The challenge for the process engineer is to know which package to use and to know whether a particular application is the most accurate for the specific process. Metallurgical simulation programs today are well known and proven. Certain programs are specialized while others are broader based. The needs of each user are dependent on the application. Typically, most users require the following operations: • Comminution • Flotation • Hydrometallurgy • Pyrometallurgy • Additional requirements could be defined as: • Thermodynamic capabilities for solids, phases, and gases • Dynamic simulation • Data analysis tools • Coal oriented operations • Diamond oriented operations

Jan 1, 1997

By Robert K. Towner, Francis S. Kendorski

Shotcrete drift linings at the Climax Mine of the Climax Molybdenum Company have undergone four years of extensive evaluations as a replacement for thick poured-in-place concrete linings. Any drift lining at Climax must be able to withstand the rigors of undercut and secondary blasting, weight problems induced by panel caving, and the abrasion of slusher mining. Examined here are the conclusions reached so far on shotcrete drift linings which have not yet completed the approximately six-year cycle from development to ore exhaustion. Properly applied shotcrete is an adequate drift lining for all phases of the Climax panel caving system of mining. Undercut blasting will damage shotcrete unless blasts are correctly timed. Weight problems will destroy shotcrete drift linings as efficiently as it will destroy concrete or steel support systems. Abrasion and secondary blasting results are inconclusive as the shotcrete lined slusher drifts have not entered the ore production stage of the mining cycle. In addition to drift linings, Climax has found shotcrete to be invaluable for lining large underground shops, for temporary support systems, for permanent ventilation bulkheads and for the repair of abraded or weight damage concrete lined slusher and haulage drifts.

Jan 1, 1974

By James R. Oehler

Progress, future challenges, and the continual search for more efficient and rapid methods of excavating underground openings and shafts were main themes at the 1983 Rapid Excavation and Tunneling Conference (RETC) held June 12-16 in Chicago, IL. The event, jointly sponsored by the Society of Mining Engineers, the American Society of Civil Engineers, the Canadian Institute of Mining and Metallurgy, and the Engineering Institute of Canada, offered a diverse program for both civil and mining engineering disciplines. Although all papers given at the three-day conference were noteworthy contributions, and each is included in the conference proceedings currently available from SME, there were a few sessions that had particular mining-related interest. Research, Acceptance Needed for Water-Jet Technology Water-jet-assisted rock excavation is seen by some as a technology moving from the prototype phase to a fully developed, accepted system within the next decade. For an industry that is traditionally fairly slow in accepting significant changes, this development appears especially noteworthy. However, speakers at the water-jet technology session generally agreed that many large US manufacturers are not viewing water-jet-assisted equipment as viable replacements for all-mechanical systems. This, they fear, may mean some US manufacturers will lose a significant share of certain equipment markets to foreign competitors who are moving aggressively ahead in this area. Despite the advantages of increased cutting rates, reduced power requirements, less dust, prolonged bit life, and reduced sparking in many cutting situations, water-jet technology applied to mining is apparently having some acceptance problems in the US. R. J. Evans, professor of industrial engineering at the University of Pittsburgh, noted that there are several perceptual barriers to water-jet coal cutting; such as uncertainties concerning the fu¬ture demand for coal and the reliability of equipment, apprehensions that jet-assisted equipment will make the mine operator dependent on specific types of hard-to-obtain equipment, and fears about accessibility of the equipment for repairs. Evans also said numerous parameters need defining before taking advantage of water-jet-assisted cutting systems in under-ground coal mining in the US. For the cutting head, information must be obtained on optimum bit geometry and spacing, and maximum and minimum torque requirements. For a complete US water-jet cutting system, Evans added, research is needed to establish optimum jet pressures, jet powers, number of jets per bit, and location of jets relative to the bit. One research project making progress towards optimizing parameters for a water-jet-assisted drag bit cutting system for coal mining was described by Levant Ozdemir, director of the Earth Me- .

Jan 8, 1983

By d&apos, J. A. Oliveira, A. K. L. Resende, L. F. G. Assumpção, J. D. Neto

Kaolin samples from Rio Capim Resources were treated in conventional and superconducting magnetic separators to study the main variables that influence the impurity removal process. Two coating clays and a delaminated clay were tested. The variables studied were retention time (cross-sectional velocity), magnetic-field intensity and matrix type. The feed brightness ranged, from 84.7% to 87.6% ISO, for the coating clays and ranged from 80.7% to 85.4% ISO for the delaminated clay. Using a conventional magnetic separator with an applied, field of 1.5 to 2.0 T (tesla), the brightness values were higher than 88% ISO for the unleached coating claw products and were higher than 87% ISO for the unleached delaminated product. With a maximum field intensity in the superconducting machine of 5.0T unleached brightness values higher than 88.5 % ISO were attained for both coating and delaminated clays.

Jan 1, 1997

By D. M. Sloan

While surety capacity for the mining industry continues to shrink, States are demanding greater financial certainty for closure/post closure obligations. To combat these demands, larger mining companies are pursuing a Mining Surety Reinsurance Program that requires a significant up front capital contribution. This paper outlines an alter-native program for middle market mining organizations. The program utilizes a “Blended Finite Risk” environmental insurance solution with surety acting as the “front” in states where insurance is not an acceptable form of collateral. Marsh proposes creating separate programs for each State requiring surety. The reason for separate programs stems from each states’ different surety rules. Insurance companies typically require at least $5 million in future value remediation liabilities for finite risk programs. Since most middle market mining companies have obligations that fall below this threshold, the Blended Finite Risk Program contemplates combining several companies closure/post closure liabilities to accomplish the minimum amount required by the insurance company. Why use a Blended Finite Risk Program? One of the primary benefits is the financial assurance that funds will be available for planned remediation. For example, the financial assurance may be required by a government agency. The certainty may help facilitate a merger or acquisition. Additionally, the funds may be part of a CER-CLA PRP settlement. In all cases, the insurer providing coverage would be a secure independent 3rd party. A Blended Finite Risk Program also provides a long-term solution – up to 30 years and in some select cases longer. The benefit to a state or the BLM is the removal of financial uncertainty. An insurance company writing the policy would have an AA or AAA balance sheet. The hardening of surety markets coupled with the tightening of financial assurance requirements in many states have necessitated the posting of 100% collateral. This program substantially reduces these collateral requirements.

Jan 1, 2004

The research deals with the study of the quality indicators in the productive process and its use for the consuming market, for two types of ores: industrial sand and crushed stone. Companies who represent the profile of the São Paulo producing market in its respective modalities well produce the selected cases. The development of the studies have to be, for the application of consistent methodological models of the fundamentals of the Engineering of Quality, especially how much to the statistical control of processes and its trustworthiness, of form that the results of the research can serve as referential in the boarding for other generic cases of the mineral industry.

Jan 1, 2003

By C. Roldan, C. Garcia, J. D. Miller, C. L. Lin

The ultimate recovery in a heap leaching operation is related to the degree of exposure of the valuable minerals in comminuted particles. Recently, high-resolution cone beam x-ray microtomography (XMT) has been used to determine this parameter. XMT technology consists of examining the extent of mineral exposure for each size fraction of ore in 3D, then, by algebraic calculations, the ultimate recovery can be estimated for different particle size distributions (PSD). To confirm the usefulness of the XMT technology for mineral exposure analysis, column tests were performed to determine ultimate recovery using three PSDs for two composites obtained from the copper heap leaching operation at Zaldivar-Chile.

Jan 1, 2003

By J. Andersen

The very large quantities of energy used for size reduction in the minerals processing industry necessitate the accurate prediction of comminution machine power draw for optimum plant design. The JKMRC has developed effective models for predicting ball mill, autogenous mill, semi- autogenous mill and crusher power draw. When combined with comminution models they provide a powerful tool for evaluating not only the size reduction performance of a plant design, but its power utilization efficiency as well. This paper describes the structure of the mill and crusher power models. Data from a wide range of equipment types are presented which illustrate the accuracy of these models.

Jan 1, 1992

By Jim Morris, Davin Ishii

The major source of water for Southern Nevada is Lake Mead. However, the existing pump station located on Lake Mead is inadequate for one of the fastest growing areas in the United States. In order to keep up with the increasing demand for water in Las Vegas, a parallel system is being constructed. The intake for this system is being constructed approximately 68.58m (225ft) below the surface of Lake Mead. The lake tap consists of installing casing and secant piles to support the shaft collar, excavating a 21.34m (70ft) deep intake shaft, and installing a3.66m (12ft) diameter steel liner.

Jan 1, 1999

By Richard B. Muter

In determining the layout or combination of unit operations to be utilized in a modem preparation plant, several factors must be taken into account. Among these are the washability data, size consist data, the particular market or markets for the coal, the mining method used, the degree to which the coal must be prepared, expected fluctuations in raw coal and markets, and the overall economics of the process. In addition, there are the health and safety aspects of coal utilization and preparation. Chapter 1 of this book discusses the characteristics of coal and coal markets, while Chapter 2 deals with the design of preparation plants. Once the unit operations for a particular plant have been decided upon, these arrangement may be depicted by using a flowsheet. A coal preparation plant flowsheet is a two-dimensional graphical representation of the sequence of operations, the arrangement of machinery, and the flow of materials for a particular coal cleaning operation. The flowsheet is usually qualitative in nature, becoming more quantitative as material balances, water balances, numbers and sizes of various pieces of equipment, etc. are added. The usual convention in preparing a flowsheet is to show the feed flowing from left to right, starting at the top left and working down as in an all-gravity process. Various symbols are used for each unit operation as depicted on a flowsheet, and Fig. 14-37 is a compilation of the commonly accepted international standard symbols for each unit operation. Fig. 14-38 through Fig. 14-40 are flowsheets of various coal cleaning processes as published in the January 1976 issue of Coal Age. Each process has its own unique features which, among others, depend upon the coal being cleaned, the coal market, and the mining operation. Fig. 14-38, for example, is a flow diagram for a jig plant preparing steam coal from two strip mines located a few miles apart. In addition to the jig washer, cyclones are used to treat the finer size coal. Fig. 14-39 is a flowsheet of a heavy media plant using a heavy media washer for + %-in. (+6.3-mm) coal, froth flotation for -28 Tyler mesh (-0.6 mm) material, and dewatering phase units (dwp) for Y, in. x 28 Tyler mesh (6.3 x 0.6-mm) cleaning of steam coal. In addition, thermal drying, centrifuge drying, and the use of vacuum disk filters and thickeners for dewatering are depicted. Fig. 14-40 is a flowsheet of a plant producing metallurgical coal. In addition to the heavy media and froth flotation circuits, a tabling circuit is also employed. These flowsheets are intended to give the reader an example of how the various unit operations for coal cleaning may be linked together. Figs. 14-41 and 14-42 illustrate the conversion of block diagrams into an IS0 prescribed set of symbols.

Jan 1, 1991

By C. W. Schultz

The Mineral Resources Institute at The University of Alabama is engaged in a program whose objective is to develop a beneficiation system for Eastern oil shales. Prior experience (1,2) at The University had shown that the grind required for liberation of the oil rich kerogen was substantially below 20~m. Based on this fact and the rapidly emerging consensus that column flotation is the preferred method for ultrafine particle separation, efforts were focused on the column flotation of oil shale. This paper, which must be regarded as a progress report on a continuing MRI project, describes the observations made and the results achieved to date. The investigation is being conducted in two phases. The first phase has been completed and consisted of a factorially designed experiment conducted for the purpose of screening a set of primary flotation variables. The second phase, which is still in progress, is focused on optimization of the operating conditions and development of a flowsheet for specific shales.

Jan 1, 1989

By Andrew P. W. Briggs, Corale L. Brierley

A considerable economic and technical knowledge base has been amassed with the successful and sustained operation of commercial minerals bioleaching/biooxidation plants to extract copper from chalcocite ore and enhance precious metal recovery from sulfidic refractory ores and concentrates. Economic evaluation ofbio-processing must consider the value of the ore, the sulfide-sulfur requiring oxidation to achieve significant metal recovery, the time required for the biological process and, in the case of precious metal feed-stocks, the down-stream reagent consumption. Of these considerations oxygen requirement for the biologically-catalyzed oxidation of sulfide minerals is the prevailing determinant in the capital and operating costs of aerated, stirred-tank reactors for processing concentrates and bio-heaps for processing ores. Oxygen requirement is dictated by the amount of sulfide-sulfur requiring oxidation to achieve desired metal recovery. The testwork program to evaluate a project for application of biooxidation/bioleaching must be designed to insure that factors critical to economic assessment are fully quantified.

Jan 1, 1997

By Peter M. Turcic

A Mine Safety and Health Administration (MSHA), National Institute for Occupational Safety and Health (NIOSH) and Bureau of Mines (BOM) interagency task group was established to assess the health and safety implications of the use of diesel-powered equipment in underground coal mines. The objective of the group was to conduct an assessment to identify areas of concern, to evaluate the adequacy of existing methods for addressing the identified concerns, and to recommend agency approaches for addressing inadequacies. The interagency group concluded its work in April 1986 and presented a report to the Assistant Secretary for Mine Safety and Health. The report included the conclusions reached by a group and recommendations for regulatory action by MSHA. This paper will present the methods and approaches used by the interagency task group and will discuss the findings, conclusions and recommendations of the group. The paper will attempt to meld together the technical and policy aspects of the issues involved with diesel equipment in coal mining.

Jan 1, 1987

By Klados. T.

MSC.Software assessed the performance of the drive end and non-drive end bearings on a ball mill using the finite element method. The assessment included the effect of mill and pedestal deformation on the performance of the bearings. Oil film thickness, oil pressure distribution and power requirement were of interest. A solution approach coupling a structural solver to a Reynolds equation solver was specifically developed for the project. Results showed that the deformation of the bearing surfaces had a significant influence on the performance of the bearings. For example, for the non-drive end bearing, the minimum oil film thickness computed for the deformable bearing surfaces was significantly lower than calculated for the non-deformable case. The results also showed that cavitation was likely in both the drive end and non-drive end bearings (severe negative pressures were obtained in both bearings). Other design variations were also assessed, e.g. a case with a modified radial clearance which improved the results.

Jan 1, 2006

By James L. Crowe

Electric-power-generating plants fired by fossil fuels are faced with increasingly stringent requirements for control of sulfur emissions. Several approaches for limiting these emissions, or for operating such facilities in an environmentally acceptable manner, are being pursued. Some of the approaches are based on the use of naturally occurring carbonate rocks or of materials derived from them. This paper discusses primarily the carbonate-rock-based processes being developed for control of sulfur dioxide emissions from fossil-fueled electric-power-generating plants. It includes a discussion of the role of carbonate rock materials in removal of sulfur dioxide from stack gases after combustion, capture of gaseous SO2 during the combustion process, and removal of sulfur from fuel prior to complete combustion. Materials derived from carbon- ate rocks are generally used in processes which convert the sulfur to a throwaway product, but there are also proposed processes in which the sulfur is converted to a useful product and the absorbent is regenerated for reuse.

Jan 1, 1974