Search Documents

By D. M. Muir

Thiosulfate offers a non-toxic alternative to cyanide for processing gold ores. The mechanism of leaching gold using ammoniacal thiosulfate solution is driven by the Cu(II)-Cu(I) redox couple and is complicated by competing ligands such as NH3 and S2O32-. It is shown that an understanding of the copper speciation and sulfur speciation is required to optimise this system. This paper presents Eh-pH and speciation diagrams for varying concentrations of Cu(II), S2O32- and NH3 and discusses the conditions under which various copper and sulfur species are stable.

Jan 1, 2001

By H. Razavizadeh

The recovery of copper from oxide ores containing from 2% to 4.1% acid-soluble copper from the Sarcheshmeh mine in Kerman province of Iran was investigated by agitation leaching in sulfuric acid media. Quartz, as a major constituent, and malachite, as the major copper mineral, were identified in the ore by X-ray diffraction (XRD) and microscopic studies. A series of leaching experiments on the ore was performed over a concentration range of 10 to 20 g/L and temperatures from 15° to 50°C for a maximum of 3 hours. An initial high dissolution of copper was followed by a very slow reaction. By increasing acid concentration and temperature, the dissolution rate of copper was accelerated. However, by increasing acid concentration, the acid consumption of ores was also increased. Surface morphology of solid residues at various leaching times was examined with a scanning electron microscope (SEM). All SEM micrographs of the partially reacted particles displayed a needle structure. The kinetic studies showed that the malachite dissolution rate could be modeled in two stages. About 85% of the malachite dissolution occurred in Stage 1, while the remaining 15% occurred in Stage 2. The data obtained for the leaching kinetics indicate that the dissolution for Stage 1 was a diffusion-controlled reaction with an activation energy of about 20.6 kJ/mole, and the dissolution for the Stag 2 was a chemical-controlled reaction with an activation energy of about 87.6 kJ/mole.

Jan 1, 2008

By Sakai Kunito, Nigel B. Sugden

If an Earth Pressure Balance (EPB) TBM is operated effectively tunneling can be carried out producing negligible ground movements. Using the methods given in this paper face losses of the order of 0.5% and less are generally obtainable using an EPB. Operating the EPB TBM in this manner reduces the requirement for the building protection measures used to protect surface structures. This can result in a considerable cost saving for the construction of a tunnel under built up areas. This paper to give guidance on the causes of ground movements around a TBM and the methods of running an EPB TBM that will minimize those movements. Details of how this was successfully done during the construction of the Bangkok Metro are given. The paper is split into three parts as below. 1.Causes of ground movements due to TBM tunneling 2.Methods of controlling those movements using an EPB TBM 3.Case history Bangkok Metro (water main)

Jan 1, 2001

By P. J. Bethell

Background Increasingly complex geological conditions, with the presence of high ash binders in the mining horizon were encountered at the A.C. I. Dugout Mine near Price, Utah. This led to the production of high ash coal from the Dugout Mine during 2003 and 2004. This material had poor marketability and posed operating issues for the utilities burning the coal. Ash levels increased from typical levels in the 9-12% range to between 15 and 25%. etween 15 and 25%. Reviews of the mine plan and expected geological conditions indicated that further periods of high ash production could be expected. Action Plan Detailed sampling of the mine high ash production was carried out. The majority of the coal from the Dugout Mine is trucked to the Savage Coal Terminal (SCT) at Wellington, Utah where it is stored in multiple piles by quality. Coal at the mine is segregated by a CoalScan 2600, on-line analyzer into high ash, low ash and rock chute (waste material). From these piles, the material is crushed prior to shipment to SCT. The samples obtained from the various high ash piles were subjected to detailed sizing and washability analysis. Once this information was obtained, alternative circuit configurations were evaluated to process this material into a salable product. Water supplies in the arid terrain where the plant is located are scarce. This factor played a part in the final circuit design.

Jan 1, 2008

The title of “the world’s biggest volume-produced hydraulic breaker,” that was held for more than a decade by the Atlas HB 7,000, changed hands with the launch of Atlas Copco’s HB 10,000 at bauma 2007. A service weight of 10 t (11 st) and up to 50 percent higher productivity represent major steps toward a new market segment: the use of hydraulic breakers as cost-efficient production machines for primary breaking and as a true alternative to drilling and blasting. The HB 10,000 has all the technical features developed by Atlas Copco for its hydraulic breakers and includes: StartSelect — the breaker’s start-up and shut-down behavior can be adapted to the conditions. AutoControl that ensures an optimized balance of impact energy and impact frequency to maximize percussive performance. Auto-Control also reduces blank firing force and controls energy recovery. PowerAdapt — if oil pressure is too high, the breaker shuts down automatically. This prevents downtime and is particularly useful when breakers are used on different carriers. DustProtector II — a combination of multiple strippers prevents abrasive rock dust and foreign bodies from penetrating the lower breaker section. Conti- Lube II — the automatic lubrication unit guarantees optimal lubrication of the breaker at all times.

Jan 1, 2007

By Adam Shang Robert Fu

The Yung-Chung-Tunnel in Taiwan, constructed for the Taiwan-East Railway Bureau, collapsed during construction when a water bearing, fractured marble zone was intersected. The inflow was approximately 4,000 liters/second. In spite of 30 relief holes the total inflow into the tunnel remained constant. The pre-excavation grouting through the re-aligned tunnel had to be conducted under extreme flow-conditions. A hot bitumen grouting program was selected for technical and economical reasons out of 13 international proposals. The technical challenges were: grouting under severe flow conditions high formation water pressures to be injected with hot bitumen at high temperatures and pressures The hot bitumen grouting program resulted in a dramatic reduction in the hydraulic conductivity and stabilization of the formation and facilitated a problem-free excavation.

Jan 1, 2007

By D. R. Wilburn

This summary of international mineral exploration activities for 2008 draws upon available information from industry sources, published literature and U.S. Geological Survey (USGS) specialists. The summary provides data on exploration budgets by region and mineral commodity, identifies significant mineral discoveries and areas of mineral exploration, discusses government programs affecting the mineral exploration industry, and presents analyses of exploration activities by the mineral industry based upon these data. Two types of information are reported and analyzed in this annual review of international exploration for 2008: 1) budgetary statistics expressed in U.S. nominal dollars provided by Metals Economics Group (MEG) of Halifax, Nova Scotia (Metals Economics Group, 2008a, b), and 2) information on regional and site-specific exploration activities that took place in 2008 and compiled by the USGS. The MEG information summarizes planned company budgets for worldwide exploration activities in 2008, primarily for precious metals (gold, platinum-group metals and silver) and base metals (copper, lead, nickel and zinc). MEG includes information on additional mineral commodities only where it is available. Information on uranium exploration was included in the MEG overview for the first time in 2007, although this information was not included in the USGS analysis. The MEG survey methodology was changed in 1999 to include companies with exploration budgets between $100,000 and $2.9 million, as well as those companies included in prior studies whose anticipated budgets were above $2.9 million. MEG estimates that its post-1999 surveys cover at least 90 percent of world nonferrous nonfuel mineral exploration budgets. The 2008 survey is reported by MEG to cover an estimated 95 percent. Companies that chose not to participate in the MEG study, private companies that do not publish data, and government-funded exploration activities make up the majority of the remaining 5 percent. MEG included 91 more companies in its 2008 survey than it did in 2007 USGS compilations of site data described here primarily include nonfuel minerals, with an emphasis on base metals, diamond and precious metals. Analyses are based on information provided by USGS mineral commodity and country specialists and by other USGS scientists, as well as industry contacts and trade journals.

Jan 1, 2009

By Alfred Weiss

Selecting a minicomputer is not unlike selecting a costly piece of mining equipment such as a truck, shovel, crusher, or conveyor belt system. A marked difference might lie in the frequency at which such selection takes place; another difference might be mine management's familiarity with mining equipment vis a vis a minicomputer. These basic differences might prompt a mining company to seek the aid of a consultant when selecting a minicomputer system. Advantages and Disadvantages The fundamental advantage of employing an independent consultant is that it provides management with a source of knowledge and breadth of experience not readily available within the organization. If the consultant has a minerals background, such knowledge and experience are further enhanced by actual experience in exploration, mining, and mineral processing. If the consultant has worked within a mining company, such hands-on experience is supplemented with a meaningful understanding of the client's business; this facilitates communication between the consultant and members of the client organization. The consultant has been, so to speak, "in the client's shoes." There are several other advantages. Since computer systems cut across organizational boundaries, the independent consultant may be able to move within the organization more easily than an inside staff person to collect necessary information. Also, detachment from any manufacturer should provide the client with an objectivity and a set of recommendations as near optimal as feasible. The principal disadvantages lie in the area of continuity and accountability. Once the consultant's report has been submitted and his recommendations implemented, a discontinuity might occur. Also, if implementation does not provide the desired results, the consultant might not be available to correct the situation or account for actions taken. Proper selection of consultant services, relative to kind and duration, and the consultant's method of operation, will often prevent many of these aftereffects. Services Offered The professional consultant can help a client: •Define and summarize information systems technology* needs; • Evaluate alternatives such as in-house capability and capacity, time-sharing, or service bureaus; • Prepare a formal request for proposal (RFP) to be submitted to vendors; •Evaluate vendor proposals; •Evaluate the economics of lease vs. purchase; and •Assist in the conversion and installation. Thus, consulting services may range from evaluating an existing system and upgrading to a larger piece of equipment, to selecting a new first-for-the-organization computer. First, Define and Summarize Needs Regardless of circumstances, the most valuable document required before equipment selection is the information system plan (I/S plan). It helps insure that the company's information needs are met in a cost-effective manner. An I/S plan is usually a comporient of the mining company's overall business goals. Since an I/S plan is a formal vehicle for establishing and communicating the direction the organization intends to take to satisfy information requirements needed to achieve goals and objectives, most initial systems services are likely to center around creating such a document or updating an existing document. The trend toward company-wide I/S planning is increasing in the mining industry; however, smaller scale efforts focused at the information systems needs to support an individual

Jan 11, 1981

By N. Ward

The Gualcamayo Mine is located in the Andes Mountains north of San Juan, Argentina (Figure 1). A property of Yamana Gold Inc, it declared commercial production in July 2009 and has a total mineral reserve and resource base of approximately 88,000 kg of gold. Crushing operations for the open-pit mine are located in a 13,500 m3 underground cavern with a ceiling height of 22 m. More than 3,600 m of tunnels are used to access the cavern and convey the ore. The Project as described in this paper relates to the design and construction of the Main Cavern, Conveyor System Exit Tunnel, the Mechanical System Access Tunnels, and two 4.20 m diameter shafts (Ore Pass #1 and Ore Pass #2) as shown in Figure 2. [ ] Preliminary engineering for the Project was performed by Hatch Chile. Rizzo Associates Argentina, S.A., a division of Paul C. Rizzo Associates, Inc (Rizzo) was contracted to provide geomechanical and geotechnical support for the construction of the access tunnel system and geomechanical design and construction supervision for the cavern and shafts.

Jan 1, 2011

By Rick Frechette, Bryan Ulrich

Representatives from several mining operations in three western states left their mines behind for a day in February to discuss with their peers the issue of water. The event was Knight Piésold and Co.’s Roundtable 2007, held in Elko, NV. It was third such event put on by the company. The issue this year was site-wide water considerations.

Jan 1, 2007

By A. L. Williamson, G. Savci

Hydrologic assessments of existing and proposed waste rock stockpiles (WRS) are typically required for application of operating and closure permits at mine sites. The results of these assessments can be used to determine the applicability of the state groundwater permit program requirements to the operation and closure of these stockpiles. The objective of this hydrologic assessment was to ascertain whether or not the WRS at the Ajo Mine have a reasonable probability of discharging potential pollutants to the underlying aquifer under the operational mine conditions. The hydrologic assessment was performed based on an evaluation of climatic data, prediction of the net infiltration rate through the WRS and prediction of additional hydrologic factors such as the time required to deplete available moisture storage in WRS. The predicted net infiltration rates ranging from 0.13 inches/year (1.1x10-8 cm/s) to 0.24 inches/year (1.9x10-8 cm/s) are below the threshold value of less than 10-7 cm/s recommended by Hutchison and Ellison (1992) as being characteristic of conditions that produce no or negligible quantities of seepage. In addition, the total time required to deplete available moisture storage within the Ajo Mine WRS and for any potential seepage from the WRS to reach the underlying aquifer is estimated to range from 260 years to 1,950 years. Collectively, the climatological and geotechnical investigations and the hydrologic predictions demonstrate that the WRS at the Ajo Mine hydrologically do not have a reasonable probability of discharging pollutants to the underlying aquifer. As a result of this prediction, the stockpile will not be regulated under the state groundwater permit program and operational and reclamation requirements will be limited to managing surface water runoff.

Jan 1, 2002

By Wolfgang Roth

In 1990, a residential area above the North Outfall Sewer (NOS) tunnel constructed in 1924, experienced subsidence. After sewage was diverted into the North Outfall Replacement Sewer (NORS), soil probing from within the tunnel was conducted, soil-improvement options were developed, and a preferred grouting scheme was analyzed by numerical modeling to evaluate the stability of the 80-year+ old tunnel liner under grouting-induced loading conditions. This paper discusses the initial field investigation and the development and analysis of a grouting scheme originally intended to be implemented before relining of the tunnel. The scheme was later modified, and the new liner was installed before the final probing and grouting work was done.

Jan 1, 2008

By Maurice Grieves

GC. Waterman Mr. Grieves' paper on "Shaft Sinking Today--A Boring Business Tomorrow" in the Dec. 1981 issue of MINING ENGINEERING is an excellent description of recent improvements in speed and costs of shaft sinking. However, shaft boring techniques are not a recent development. In 1935-36, the Idaho Maryland Co. (gold), Grass Valley, CA, bored the vertical 1.5-m-diam Idaho No. 2 ventilation and supply shaft to a depth of 346 m. The equipment was designed and perfected by Branner Newsome and was, I believe, described in "Transactions." Pickands Mather later bored a 1.8-m-diam shaft to a depth of about 305 m using Newsome's design. The Idaho No. 2 shaft cut through hard gabbro, diabase dikes, soft serpentine, very incompetent ankeritized serpentine and a strong fault zone. The completed shaft did not require timber support; the fault zone was cemented. Equipment consisted of a rotating 1.5-m or 3-m core barrel with a slotted bottom which cut a 76-mm kerf. The cutting agent was chilled steel shot introduced into the slot as needed. The driving mechanism and core barrel were lowered into the shaft, the former secured to the wall and the inshaft "engineer" operated the motors which controlled core barrel rpm and advance. After an advance of 1.5-3 m the equipment was lifted out of the shaft, a half(?) stick of powder cut off the drilled core, and it was hoisted to the surface with a cable attached to an eye bolt at the tope of the core. A "shift" consisted of three men: hoistman, equipment operator (down the shaft), and a surface laborer. Advance was variable as equipment and techniques were perfected. Near the end of the job advance was, as I remember, 1.5-3 m per shift. Costs were, as I recall, about $115/m. Up to 4 m cores were lifted out in one piece and swung to the dump by a stiff leg derrick. The Newsome equipment was relatively inexpensive to build and operate and his method should be (more than?) competetive with the methods described by Grieves. W.E. Hawes The author, in mentioning the South African developments of the cactus grab, ignores the parallel development of the Cryderman mucker in this hemisphere. Perhaps a slightly longer history of blind hold drilling would have been in order. Blind shaft boring got a major boost at the Nevada Test Site, as part of the nuclear weapons development, when it was essential to be able to quickly assess depth for weapons testing. One of the early civilian attempts to utilize this technology occurred when Kerr McGee drilled the shaft at the Section 19 Mine at Ambrosia Lake, NM. This twin masted drill rig belonged to a subsidiary of Kerr McGee, not Shaft Drillers. This was a difficult hole, due to bentonitic shales that decomposed. Later advances in drilling fluids eliminated this problem. The Conoco project referred to is not entirely correct, and needs minor amplification: The depth of the development (not pilot) shaft drilled was 684 m, at a diameter of 3.05 m, with a 2.16 m ID hydratatic casing being installed to a depth of 669 m. Conoco Inc., not Challenger, executed the drilling, however Conoco did use Challenger Drilling Company's Rig 14-S. Rig 14-S is unique in that it is specifically designed for shaft drilling, rather than being an oil field rig used for this service. All work was planned and directed by Conoco personnel. Deviation of the aforementioned shaft from vertical was 31 cm. Two smaller shafts (pilot shafts) were drilled with the same rig. These smaller ones were drilled 1.8 m in diameter, to depth of 665 m and cased with .91-m-diam casing, to depth of 650 m to be used as pilot holes for 5.5 m diameter shafts. The total elapsed time for all drilling, casing, cementing, and rig moves was 50 weeks. The constraints mentioned of vertical accuracy, torque, wall collapse, rig set up time, lining time etc., pumping out, etc., may not be as serious as the author implies. First, vertical accuracy: The record achieved by Conoco indicates that with reasonable care, good accuracy can be obtained, primarily by having a fair amount of weight in tension, rather than on the drill bit. Second, the amount of torque that can be applied to the drill stem has been greatly increased by the introduction of larger diameter drill stems, such as the new Hughes rig uses. Third, risk of collapse of shaft walls is minimal with the proper mud program. Basically, the walls are supported by the weight of the mud and it is not removed until some type of casing is installed and grouted in. Here in the real challenge of blind drilling shafts to devise a more economical method of lining bored shafts than using steel casing. The remaining issues were minor at Conoco, provided adequate planning and scheduling takes place. An excellent paper, "Shaft Drilling--Crownpoint Project" by Hassell H. Hunter, presented at the Fifth Uranium Symposium in Albuquerque in Sept. 1981 contains details of this project. A combination of blind boring, with enlargement by either mechanical means (boring machine, or tunneling type shield) or slabbing down, with muck removal through a larger bored shaft would seem to be the future trend in shaft development. The economics, especially for wet conditions, favor this concept over conventional sinking, as has been demonstrated at Kerr McGee --Churchrock, UNC--Churchrock and Conoco at Crownpoint.

Jan 3, 1983

By J. M. Wempen

Booster fans, large underground fans, can increase the volumetric efficiency of ventilation systems by helping to balance the pressure and quantity distribution throughout a mine, reducing leakage and reducing the total power requirement. However, in ventilation systems that use booster fans there is a potential for system recirculation, the leakage of return air to intake air, and also for localized recirculation near the fan through the bulkhead and airlock doors. Air that is recirculated locally decreases the system efficiency because the quantity of air flow through the fan increases without increasing the airflow throughout the system. To understand the detailed flow characteristics of a ventilation system with a booster fan, two-dimensional computational fluid dynamics (CFD) models were developed using the software Ansys-FLUENT. Though two-dimensional models do not represent the full complexity of the flow dynamics, they do provide a good representation of the flow characteristics and they allow for a qualitative analysis of how the flow dynamics are affected by the system characteristics. The CFD models were used to evaluate how the number of booster fans, the booster fan placement, the location and geometry of the fan installation and the construction of the airlock system affect the flow characteristics and the localized efficiency of the ventilation system.

Feb 27, 2013

By Erik Sundström, Magnus Nygren

Having seen significant improvements to accident rates in the last 40 years, companies in the Swedish mining industry now show a greater focus on the development of safety cultures throughout their organisations and workplaces. However, there is a lack of research examining the different safety initiatives and strategies practiced in the industry today. This study explores the potential influence and consequences such initiatives may have on the development of safety cultures in the Swedish mining industry. Twelve interviews with experts on safety initiatives from four different Swedish mining organisations were conducted and analysed in a process based on qualitative thematic analysis to identify notable connections to safety culture development. The results of these interviews highlight proclivities in the implementation and use of safety initiatives such as subjects of focus, methods and desired effects. This enables the interpretation of the conceptualisation and methods for the development of safety culture in these organisations based on their approaches to safety development. We believe the results of this study can serve as support for discussions on safety culture development in the Swedish mining industry, and be of interest for international mining industries, in addition to approaches to research in this field. However, we also believe it is important to emphasise the opportunities to approach safety culture in mining from different perspectives than those common today.

Jul 19, 2023

This study was conducted to determine the effects of a machine-mounted scrubber and water sprays on face methane levels. Testing was conducted in the NIOSH ventilation test gallery which was designed to simulate a full-scale mine entry. In the test entry, a model mining machine, equipped with water sprays and a simulated dust scrubber, was located at the face of a 20-ft box cut. Blowing ventilation was provided using a curtain with a 40-ft setback distance. Methane released from a pipe manifold located inby the mining machine was monitored at six locations that were 1 ft outby the pipe manifold. Tests were first conducted to evaluate the effects of using sprays and scrubber separately on face methane levels. Additional tests were conducted to determine how a scrubber used with various water spray systems would affect face methane levels. The use of either sprays or scrubber reduced face methane levels significantly. The combined use of sprays with the scrubber further reduced face methane levels a small amount. Primarily the sprays affected methane levels by changing airflow distribution close to the face.

Jan 1, 2001

By Ramon LaRusso, Frank Wheby, Richard Acker

Field investigations and office studies were used to develop criteria and cost parameters related to the geologic aspects of the proposed project. These results were employed in optimization of layouts and comparison of alternative schemes, leading to selection of the recommended program. Study of project features included the development of subsurface shafts, tunnels, and mined storage areas, and the utilization of existing surface quarries. These project features were proposed for construction within the bedrock units underlying Chicago. Principal geologic considerations included bedrock structure, stratigraphic sequence of units, rock competence and uniformity, and requirements for aquifer protection. All geologic factors were interrelated with other project considerations such as surface hydrology, hydraulics, and urban setting. Data for analyses was acquired through an exploration program conducted intermittently between 1967 and 1971, in addition to that already available through numerous explorations and well constructions in the project area. The exploration program included seismic surveying, core drilling, geophysical borehole logging, and water pressure testing of boreholes, and water well drilling and testing. Extensive laboratory tests were conducted on core samples. The data formed the basis of studies enabling the formulation of preliminary design and siting criteria resulting in construction cost evaluation.

Jan 1, 1997

By M. Kuchta, A. Newman

LKAB’s Kiruna Mine, located in northern Sweden, produces about 24 Mton of iron ore yearly using sublevel caving. For efficiency, the mine must deliver planned quantities of three ore products. We use mixed integer programming to schedule Kiruna’s operations, specifically, which production blocks should be mined, and when they should be mined to minimize deviations from planned production quantities while adhering to mining restrictions (e.g., sequencing). A new production block database and a well-formulated mixed integer programming model dramatically reduce the size of the original problem; in less than ten minutes we generate five-year schedules with time fidelity of months.

Jan 1, 2002

By K. Severin, B. Flanigan, P. Marion

“Plutonic-related” gold deposits in Interior and SW Alaska (Tintina Gold Belt) vary significantly in size, grade, vein/deposit morphology, depth of emplacement, distance from causative pluton and metal association. Metal associations such as Au-Bi and Au-As-(Sb-Hg) are a good empirical indicator of depth of emplacement and distance from causative pluton and have been used successfully in exploration. Results from a variety of analytical techniques also suggest a phenomenological cause for these metal associations, e.g. gold and bismuth have linked metallogenesis at high temperatures and thus are best correlated at deposits that are deep and/or close to causative intrusions.

Jan 1, 2000

By M. Rieber

The recent history of the mercury market results almost entirely from U.S. Government actions. Its derived demand has been curtailed by U.S.E.P.A. mandates; its supply has been augmented by U.S.D.L.A. controlled stockpile releases. The resultant prices have altered its market structure, impacted mercury mining, refiners and recyclers, and affected international production and markets. From a marketplace product mercury is rapidly becoming a disposal problem. Other minerals may follow in its wake. This paper reviews developments in demand, particularly in relation to environmental constraints. Supply side impacts are considered. The impact of stockpiles, both as a market overhang and as a potential supply is reviewed. Government stockpile disposal activity is emphasized, but the size, estimated disposal rate, and quality of the private stockpiles are considered, as is the potential availability of additional material from shut-in mines.

Jan 1, 1995