Search Documents

By Harrison R. Cooper

Composition data is needed as input for executing process control and management of particulate separation for flotation control. While requirements for composition data can be satisfied in many cases by manual sampling and analysis, automatic sampling and assay systems are now viewed as justified for all but the simplest or smallest processes. On-stream X-ray fluorescence analysis (XRFA) has satisfied requirements for the main portion of metalliferous sulfide ore flotation processes as XRFA technology evolved in reliability and sophistication from its beginnings in the late 1950's. In recent years, advanced on-stream analysis technologies have reached levels of development suitable for use in process control to increase efficiencies of important processes in mining and minerals industries such as coal fines flotation and industrial minerals beneficiation (particularly phosphate beneficiation) where XRFA methods have been inapplicable. Recent technical developments pertinent to use of advanced technologies as well as improvements to established on-stream composition analysis methods are discussed.

Jan 1, 1989

By W. E. Foreman, A. Hayatdavoudi, A. Ghalambor

The objective of this investigation was to determine the sensitivity of three selected input parameters in the operational control of continuous bottom fed thickeners used for the treatment of coal refuse slurries. The three variable parameters were "Feed Flow Rate," "Feed pH," and "Feed Solids Concentration." These three input parameters were studied under three cationic-anionic polymeric conditions. For each polymeric condition, two mathematical models were developed, one for overflow response and the other for underflow response. The combination polymers produced the best quality of overflow and underflow. For this polymeric condition, change in the feed solids concentration was the most sensitive factor in the maintenance of the overflow quality, and the feed pH was the most sensitive factor for the maintenance of underflow quality. The mathematical models generated a set of plots that would allow an operator to control and/or adjust any of the three variables to achieve optimum conditions.

Jan 1, 1991

By Stefan Zanon, Ty Faechner, Clayton V. Deutsch

Secondary data are important in geostatistical simulation of continuous variables. Geophysical data and geological trends are used for modeling porosity and permeability. Multiple mineral grades must often be modeled for mining applications. Sequential Gaussian simulation (SGS) is often used because of its relative simplicity and robustness. The two most common approaches to integrate secondary data in Gaussian simulation are with (1) locally varying mean, or (2) collocated cokriging. A significant problem with both of these techniques is variance inflation, that is, the variance of the resulting simulated values is too high because of an inappropriate decision of stationarity or an artifact of choosing a single secondary data in presence of many. We introduce a self-healing procedure for dynamic correction of this problem. The dynamic correction is different for the locally varying mean approach and for collocated cokriging since there are different reasons why each of these methods causes variance inflation. The reasons for variance inflation are discussed and the self-healing is applied to a number of data sets.

Jan 1, 2002

By Firoze E. Katrak, John R. H. Black, Paul R. Ammann, Michael J. Loreth, Servi. Italo S.

Germanium is produced primarily as a by product from zinc concentrates. The important sources of gallium are alumina ores (bauxites) and zinc concentrates and residues from zinc processing. In addition, gallium as well as germanium may soon be recovered from a depleted copper mine near St. George, Utah. The major uses for germanium are in semiconductors, lenses in infrared optical systems, catalysts, and gamma radiation detectors. The major markets for gallium are in light-emitting diodes, solar cells, laser diodes, integrated circuits, microwave devices, and magnetic bubble memories. CRA projects a healthy growth in the demand for both metals. However, the role of scrap metal will continue to be important over the next decade, thus decreasing the overall demand for primary gallium and primary germanium. This paper summarizes the key elements and the economics of the markets for germanium and gallium. Much of the information, such as plant-by-plant costs of production and estimates of consumption by end use for various countries is from proprietary databases of Charles River Associates.

Jan 1, 1986

By R. V. Ramani, K. V. K. Prasad, M. Swaminathan

Engineering design involves, in addition to numerical calculations, considerable amount of expertise and judgement. The expertise and judgement is required to conceptualize and idealize the problem, select a suitable mathematical model for the problem and to interpret the model results in terms of stipulated design constraints. In recent years, knowledge based systems (KBS) have provided the capability to integrate the qualitative experiential and expert knowledge with the quantitative knowledge for improved analysis and design of systems. A possible KBS architecture for mine ventilation system design was discussed by Ramani and Prasad (1987). The expert system (ES) component of the KBS supports the analysis and interpretation phases of the ventilation design process with an algorithmic program used for the solution of alternate designs. The purpose of this paper is to discuss the data and knowledge needs for developing such a system and a formal means of their representation on the computer. A number of ES shells were evaluated to explore possible development and delivery environments for the system. A brief summary of this evaluation is also provided.

Jan 1, 1989

By John R. Marks

The recent trend in the ventilation of deep under- ground metal mines in the United States is to rely more and more on refrigeration for air cooling. This paper describes the layout and the economics of the refrigeration method used by Hecla Mining Company at the Star Mine. An economic analysis must compare the benefits of an engineering system against the costs. The benefits of refrigeration, for example, are increased production rates, a better safety record, improved employee moral, and generally lower airflow requirements. Air-conditioning costs include capital expenditures for equipment, labor and supply costs for maintenance, and power costs for machine operation. A study of whether or not to install refrigeration becomes academic when a mine reaches the critical ventilation depth1 (the depth at which adiabatic compression alone produces station temperatures equal to the desired stope temperatures). Ventilation planning alternatives for such mines, including the Star Mine, are limited to the different methods of refrigeration usage. In this case study of the Star Mine, the refrigeration layout is described in detail. After the system performance is discussed, air-conditioning costs are calculated. The paper then concludes with a cost- benefit analysis of the Star Mine refrigeration system.

Jan 1, 1980

The Sandvik Group (Sandvik AB), headquartered in Sandviken, Sweden, continues to expand its worldwide operations growth. After recent acquisitions, including Tamrock, headquartered in Tampere, Finland, the company now has annual sales of more than US$5 billion (SEK 40 billion). With the acquisition of Tamrock, Sandvik has further increased its interests in the mining industry. Sandvik Rock Tools, a familiar name in the mining industry, is one of the world's leading suppliers of rock-drilling tools. And Tamrock is one of the world's leading suppliers of drilling machinery, loaders and equipment for rock-excavation operations. Sandvik believes that the two companies combined offer customers "maximum productivity through total system solutions, including machinery, service and tools." In 1997, Tamrock posted sales of US$940 million (SEK 7.5 billion). In addition to its expertise in drilling tools and equipment, Sandvik is supported by its collective resources in specialty steel and cemented carbide. These resources include extensive research and development capabilities, with annual investments in R&D now at about US$150 million. As a result of the R&D programs, internal expansion and acquisitions, the company has nearly doubled in size during the past four years. From 1994 to 1997, nearly US$1 billion was invested in internal growth and another US$825 million has gone towards acquisitions. Return on net assets is now 22% annually. In addition to Tamrock, acquisitions of interest to the mining community include Drillmaster Inc., Houston, TX. The acquisition of Drillmaster (by Sandvik Rock Tools) has further strengthened Sandvik's position in down-the-hole drilling tools. Other major recent acquisitions by Sandvik include Kanthal, a Swedish manu¬facturer of metal and ceramic-resistant materials for electric heating furnaces, household appliances and elec¬tronics, and Precision Twist Drill, Crystal Lake, IL, one of the leading producers of high-speed cutting tools. With more than 38,000 employees worldwide, the Sandvik Group is divided into six separate business areas. Each area is responsible for its own R&D, production and sales: ? Sandvik Mining and Construction. Including Tamrock and Sandvik Rock Tools, this business area boasts of offering the most comprehensive range of "rock-working" products. These include drilling rigs, loaders, rock-excavation equipment and rock drilling tools. ? Sandvik Specialty Steel. This area includes Sandvik Steel and Kanthal, manufacturers of stainless steel tube, strip wire and bar, as well as high-alloy steel and specialty metals. ? Sandvik Tooling. This business area consists of tools and tooling for metalworking applications. Sandvik Coromant is a market leader in the development, manufacture and marketing of tools using cemented carbide, ceramics and extremely hard materials, such as diamond and cubic nitrite. CTT Tools is the world's largest manufacturer of high-speed steel tools and is now expanding operations into solid cemented-carbide tools. ? Sandvik Hard Materials. This segment produces a full range of "hard materials," ranging from cemented carbide to diamond. This area manufactures and markets a full range of cemented carbide blanks for tool manufacturers, as well as components and rolls. ? Sandvik Saws and Tools. This business area manufactures high-quality handsaws and metal saw blades, as well as hand tools ranging from wrenches to chains for logging machines. ? Sandvik Process Systems. This segment manufactures steel belts, process systems and automatic sorting systems for the chemical

Jan 1, 1998

By D. C. Shumway

Mining in Cushenbury Canyon began in 1860 when John Cushenbury left his Holcomb Valley gold prospect and discovered a silver vein in the limestones of the present day Cushenbury Mine. Cushenbury Canyon is located along the western boundary of the Mojave Desert in Southern California and on the north slope of the San Bernardino Mountains. The Holcomb Valley, immediately southeast of Cushenbury Canyon was the most prolific gold producer in Southern California. Gold mining dominated the area until World War II when interest in the Lucerne Valley Limestone deposits was peaked by the construction of the Kaiser Steel Plant in Fontana, California. The steel making process required large amounts of metallurgical grade limestone and Kaiser geologists located claims in most of the limestone deposits. Kaiser Cement constructed a cement plant and limestone mine in Cushenbury Canyon in 1956. Kaiser Cement modernized the facility in 1982 to a four stage preheater-precalciner system. Mitsubishi Cement Corp. purchased the property in April, 1988, and through further system modifications have created the most efficient and modern cement plant in the United States.

Jan 1, 1992

By Guiseppe Bonifazi

This work applies the definition of "separation function" already introduced in the paper presented at the XVIII IMPC. This 'function" (defined for a certain size distribution after comminution of an ore) refers to the recovery distribution of a mineralogical species in a product made up of all the particles having at least a given content of that species. Many tests would be required to determine the liberation function for each mineralogical species, particularly for complex ores. Several stages of comminution would need to be examined and the mineralogical composition of the particles of each grain size class would need to be analyzed for each process step. A quick and dirty method is shown for obtaining the "separation function". It is based on the processing of data from topological maps of polished and/or thin representative sections of ore. By superimposing grids of different sizes over these maps and with appropriate combinations of mesh sizes, it is possible to simulate the grain size distributions linked to different stages of comminution and then evaluate the mineralogical composition of each grain. The procedure is carried out full automatically and can simulate a complete treatment circuit, imposing cut-off grades for the products at each separation phase. It is also possible to predict the results of treatment processes that involve grinding phases. The procedure has been successfully applied to complex ores containing several useful components.

Jan 1, 1995

By John R. Thalimer

For the past four years the U.S. Bureau of Mines has investigated the early detection of insulation failure in squirrel cage induction motors. Data modeling techniques based on values calculated from a motor's voltage and current phasors were used to produce a pair of polynomial equations that calculate a motor's insulation leakage current and power. This paper describes a prototype system using these models that monitors six motors on a continuous miner for insulation leakage in order to anticipate insulation failure. The system consists of a motor-data system for each motor on the machine, a control computer located some ' distance from the miner, and a serial bus to interconnect these items. Each motor-data system consists of an analog interface to the motor's voltages and currents, a single-board computer that reads digitized data and calculates voltage and current phasors, and a bus node that interfaces the single-board computer with the serial bus. The control computer can request and receive phasor data from any motor-data system on the bus. Using models developed at the Bureau, the control computer calculates and displays two deterioration values for each motor, one for leakage current and the other for leakage power. These values are then stored into a database from which the user can display them over time.

Jan 1, 1992

"?irovski Vrh" Uranium deposit in Slovenia is type of mineralized sediments in ore bearing belts of deflected S-structure, in which the belt is less than 25% mineralized. Ore bodies of irregular small thickness, unreliably contoured, made difficult estimation of correct contours, which are necessary for design and exploitation works. The deposit was explored by vertical boreholes made at the surface and by boreholes fanned from drives. For the purpose of application of this estimation method, 1 m composites have been made in slices which were parallel to the referential belt plane. Estimation was made for 1,5m x 1,5m x lm blocks which do correspond to the size of the containers in the ore transport stage. Two variables have been used: the first, indicator of function (ore=1, waste material =0) and kriging method; the second, logarithmical content of Uranium and Minimum Mean Square Error Estimation (MMSEE) method. Based on estimated values of those variables, probability of ore quantity as well as Uranium content over determined cut-off were calculated for each block. Those two parameters enable determination of the most probable form of the ore body in ecah one metter slice. Estimation of sixteen small blocks in a large 1,5m x 1,5m x 1m block made possible estimation of ore quantity and its content for the determined cut-off, as well as categorization of exploration. This method is being used for estimation of ore reserves and planning of exploration operations. The described' methodology was tested in an exploitation block.

Jan 1, 1986

By L. J. Nicks

The current U.S. Bureau of Mines research program is addressing the recovery of flake graphite from kish, a steelmaking waste product, and the use of zeolites from abundant domestic natural deposits for efficiently cleaning up mining industry wastewater. The United States is almost totally dependent on imports for its graphite needs, but this may change depending upon the results from a pilot plant being constructed by industry using Bureau technology. Standard mineral processing techniques were applied by the Bureau to recover high-quality flake graphite from kish. It was considered innovative enough to receive an R&D 100 Award in 1992, and its commercialization has the potential to supply the total U.S. demands for graphite many times over. Zeolites have ion exchange properties similar to ion exchange resins, but are less expensive and available in large quantities. Samples of naturally occurring zeolites were tested for their efficiency in removing metal ions from synthetic and industrial waste solutions. The tests focused on defining their selecting, loading, eluting, and regenerating characteristics, and on developing a method for recovering the metal ions as added value products. The results showed that the removal of metal ions with zeolites from acid rock drainage (ARD) solutions is technically feasible and that this technique has the potential for being used in an integrated chemical treatment systems approach either as a primary or secondary cleaning step.

Jan 1, 1995

By J. M. Kaufman

Recent mining regulations have increased the need for detailed engineering and environmental information pertaining to the hydrogeologic environment in mining areas. The cost of obtaining such hydrogeologic information has also increased. After mineralization of potentially economic grade ore and tonnage has been identified, and after completing preliminary mining feasibility studies (suggesting that development is merited), a second exploration phase can incorporate a simple, cost-effective baseline hydrogeologic data reconnaissance program that is linited but useful. Using exploration drill holes only, this program can provide a direct indication of where ground water is encountered. Also, reasonable estimates can be made on the relative production of water from various water-bearing strata, a composite potentiometric surface map can be prepared, and the general chemistry of the ground water can be characterized.

Jan 1, 1984

By Joel K. Waterland

GENERAL DESCRIPTION Open cut-and-fill stoping for many years was prob¬ably the most widely used mining method in under¬ground metal mines. Then for a time this method was largely supplanted by the blasthole stope. It again be¬came popular as many mines reached depths or grades where methods requiring large open voids to remain open for extended periods of time became unsuccessful, often as a result of excessive dilution. The open cut-and-fill method is very flexible and is readily adaptable to almost any ore body. The standard application requires that a slice of ore usually 2.4 to 3 m (8 to 10 ft) thick be removed from the back of the stope, and as the ore is taken down, the back is dressed and rockbolted. After the back is secured, the broken rock is removed through rock passes to the level below. When the rock has been removed, the rock passes are extended upward the height of the ore removed, the stope is backfilled, and another cycle is mined. This method is best employed in plunging ore bod¬ies with considerable vertical extent, ore areas that re¬quire selective mining, ore areas where weak wall con¬ditions exist, and ore bodies that have an ore value that will carry this relatively expensive mining method. Blast¬hole stoping, shrinkage stoping, and other mining meth¬ods that do not employ rock passes in a stope are not efficient in plunging or flatly dipping ore bodies because the footwall makes ore removal quite difficult. Since mining is accomplished by taking down slices of the back, only small areas of the wall rock are exposed at any one time, and these only for short periods. Due to limited back height, areas of uneconomic rock may be left in place, or they may be mined and the material gobbed in the stope. Because the miners in the stope must work under freshly blasted areas, the amount of ground control is usually great. The volume of rock that is broken during one section of mining is relatively small and the amount of nonproductive work required is high. This results in limited productivity for the scope and, be¬cause of the nonproductive work that must be done on a regular basis, the production from the stope may be quite cyclical. SUITABLE ORE BODIES The open cut-and-fill method may be adapted to al¬most any type of ore body with a relatively high vertical extent. The ore body must be accessible at both top and bottom as well as at regular intervals throughout its vertical extent. Although adaptable to most ore bodies, the method is probably best employed where the ore has poor con¬tinuity and where most types of bulk mining would pro¬duce excessive dilution. In areas of poor ore continuity, the capability of continuous and extensive sampling dur¬ing the mining of each cycle makes this method very desirable. This capability also minimizes the amount of evaluation sampling that must be done before mining is started. Because of the extractive system used, the size and shape of the stope may be as readily changed as the sampling mandates. Probably the only ore characteristic demanded is that the ore has strength enough to be sup¬ported through the use of rockbolts or cable bolts dur¬ing the mining and backfilling cycles. Good planning, systematic sampling, and careful supervision will pro¬duce a product with less dilution than any other open stoping method. PLANNING Evaluation Planning Once it has been decided that the open cut-and-fill method would be the most efficient for mining a par¬ticular ore body, the next considerations would probably be the availability of an economical backfill material and the selection of an efficient transport system for this material. Although hydraulically transported mill tail¬ings are the most widely used product, this is not always practical due to mill location or the quality of the tailings. In such cases, backfilling may be used. The type of backfill and the type of equipment used will determine if a floor or capping on the backfill is required to minimize dilution during ore removal. The early selection of rock removal equipment is im¬portant since equipment usually determines the amount of development work required to bring a stope into pro¬duction and the size of the openings needed. The size and continuity of the ore body will usually determine the type of loading equipment. The use of slushers or load¬haul-dump (LHD) equipment captive in the stopes will minimize the amount of development. If the ore con¬tinuity is such that a ramp system for extraction can be used, the cost of development will be increased but the flexibility of continuous mining will minimize the cycli¬cal nature of the production. The height of the mining section usually is deter¬mined by the strength of the wall rock and the amount of back bolting required. Once this has been decided, the appropriate drilling equipment can be chosen. The number and sizes of the rock passes employed depends upon the type and size of the extractive equipment and the type of backfill that is to be used. Since the miners must enter and leave the stope each shift, the level inter¬val is usually maintained at approximately 45 m (150 ft). Access from the level above into the stope must be main¬tained at all times. The employees perform all the work in the stope and adequate ventilation must be provided. Stope Planning Due to the flexibility of the method and the vari¬ability of the ore zones, layout is usually done on a stope basis. In areas where continuity is a problem, the size of the stope is usually determined by the boundary of the ore (with all of the ore within that boundary being removed). In areas of good continuity where ramps are to be used, the length of the stope may be determined by the length of time each of the cycles (preparation, back¬fill, mining, and ore extraction) requires. The ramp work is then laid out so that access to the various parts

Jan 1, 1982

By J. Wagner, P. Eger, G. Melchert

In 1991, LTV Steel Mining decided to close an open-pit taconite mine in northeastern Minnesota using a passive-treatment approach consisting of limiting infiltration into the stockpiles and wetland treatment to remove metals. More than 50 Aft (55 million st) of sulfide-containing waste had been stockpiled adjacent to the mine during its 30 years of operation. Drainage from the stockpiles contained elevated levels of copper, nickel, cobalt and zinc. Nickel is the major trace metal in the drainages. Before the closure, the annual median concentrations ranged from 1.5 to 50 mg/L. Copper, cobalt and zinc are also present but they are generally less than 5% of the nickel values. Median pH levels range from 5 to 7.5, but most of the stockpile drainages have pH levels greater than 6.5. Based on the chemical composition of each stockpile, a cover material was selected. The higher the potential that a stockpile had to produce acid drainage, the lower the permeability of the capping material required Covers ranged from overburden soil removed at the mine to a flexible plastic liner. Predictions of the reduction in infiltration ranged from 40% for the native soil to more than 90% for the plastic liner. Five constructed wetlands have been installed since 1992. They have removed 60% to 90% of the nickel in the drainages. Total capital costs for all the infiltration reduction and wetlands exceeded $6.5 million, but maintenance costs are less than 1 % of those for an active treatment plant. Because mine-drainage problems can continue for more than 100 years, the lower annual operating costs should pay for the construction of the wetland-treatment systems within seven years.

Jan 1, 2000

By Gregor de Ratmiroff

Field prospecting for bauxite in Venezuela has had a long but interrupted history having till now oferred but evidence of occurrences. The Venezuelan Government, trough the Corporación Venezolana de Guayana (C.V.G.), in 1974, formalized a major effort in prospection for bauxite in the Shield area and the Orinoco Delta in orden to establish the possibility of raw material supply to an upcoming and expanding aluminium industry. The Corporation, in turn, created and delegated to the Division of Geological Stu- dies, the formulation of the necessary infrastructure and execution of work in orden to determine the existence of economically exploitable bauxite deposits.

Jan 1, 1979

By Keh-Jian Shou

"This study adopts and analyzed a shield tunneling case in Taiwan, with a diameter from 5.25m to 6.70m and the smallest radius of curvature 100m, which was constructed in gravel formations as well as a vibration sensitive area. In this case study, a vibration monitoring plan, comprising the sensors inside the shield machine and on the surface, was proposed and performed to provide the vibration data during the construction. In this project, the major vibration reduction considerations were increasing the open ratio of the cutter head (to reduce the cutting function) and reducing the rotational speed of the cutter head. The results of the construction suggest the appropriateness of the above considerations. The findings could provide suggestions to the other similar shield tunneling cases. INTRODUCTION Underground vibrations during shield tunneling are typically isolated and absorbed by the soil. However, a portion of these vibrations may disseminate to the surface. These vibrations are considered micro-vibrations, which generally do not pose a threat to surface structures, and are thus seldom the focus of research. The present project was located in the Hsinchu Science Park where shield excavation bypassed numerous high technology manufacturing plants (e.g., wafer manufacturing plants). The vibrations generated by shield tunneling may affect the vibration-sensitive manufacturing equipment and instruments in these plants, and induce problems in manufacturing processes. Therefore, research to comprehensively understand the characteristics and potential influence of such vibrations is essential. To clarify the characteristics and potential influences of vibrations generated during shield tunneling, the vibration level in the excavation of the Taoyuan International Airport Access (TIAA) Metropolitan Rapid Transit (MRT) Project was examined, as it possesses similar excavation conditions to the present project. The parameters collected from relevant tests were provided as a reference to the firms along the excavation route of the present project to explain the effects of vibrations, and to relevant units for shield machine selection and project execution. No yield problems resulting from shield machine induced vibrations were reported by the firms, and the vibration levels measured in the present project were comparatively lower than those in the TIAA MRT Project. Because the related literature is scarce, this study aims to analyze the collected measurement data and provide suggestions on shield machine selection or designs. Such that we can more properly evaluate and control the impact of shield tunneling induced vibrations in similar projects."

Jan 1, 2016

By T. W. Eddy

Research was conducted in which elemental mercury and its sulfide mineral (cinnabar) are removed from a copper sulfide concentrate by low temperature thermal applications. The goal of this research was to reduce, volatilize, and collect mercury vapor from concentrated smelter feed in a simulated drying environment while maintaining the chemical integrity of the residual. The study used synthesized concentrates composed of copper sulfide and mercury bearing minerals (such as cinnabar (HgS) or elemental mercury) to determine optimal residence times and temperature ranges.

Jan 1, 1996

The Mining Foundation of the Southwest (MFSW), located in Tucson, AZ, will hold its 16th annual American Mining Hall of Fame Awards Banquet Saturday, Dec. 5,1998. The Hall of Fame recognizes outstanding contributions to the mining industry by selected individuals and industry partners. Each year, one living award recipient and up to two mining history honorees are chosen by the , Hall of Fame Committee and the Board of Governors of the Mining Foundation. In 1989, the Mining Foundation initiated a Medal of Merit to recognize outstanding individual, technical and professional contributions to the mineral industry. In 1995, an award was created to recognize contributions made by companies and organizations in partnership with the mining industry. This year's inductee, guest of honor and featured speaker will be Charles G. Preble, president and chief executive officer of Southern Peru Copper Corp. He is being recognized for outstanding performance as an executive of an American company operating under difficult circumstances in a foreign country. The Hall of Fame will induct H. Myles Jacob, former chairman and CEO of Inspiration Copper Co., for innovation and farsightedness in matters pivotal to the cop- per industry of his time. In addition, John Cromwell Lincoln, former president and chairman of Bagdad Mining Co., will be inducted for his outstanding contributions to the American mining industry. These contributions include metallurgical research and development of the Bagdad Mine as well as pioneering innovation in the electrical industry. Medals of Merit will be awarded to David N. Skillings, editor and publisher of Skillings Mining Re- view, for his dedication and support of mining interests. J. Ruben Velasco Rodriguez will also receive a Medal of Merit. He is economic geologist, professor and former secretary of the board of directors and secretary general of Compania Minera de Cananea. His medal is for fostering excellent relations between Mexico and the , United States in mining geology and management and for advancing the professional development of others in the field of earth science. An Industry Partnership Award will be presented to Stephen Bechtel and the Bechtel Corp. in recognition of Bechtel's 100th anniversary and the company's outstanding service to the mining industry. The banquet will be held at the The Westin LaPaloma in Tucson beginning with cocktails at 6:30 p.m. Tickets are available from Clare A. Roscoe, manager, Mining Foundation of the Southwest 520-577-7519, fax 520-577-7073.

Jan 1, 1998

By R. F. Merwin

Advancement in automation intensifies the need to remove tramp iron from bulk materials being processed and carried on belt conveyors. Although magnets have long been employed for this purpose, it becomes increasingly necessary that magnetic equipment of appropriate types and sizes be selected and advantageously installed -- if maximum benefits are to be derived Tramp iron present in bulk materials consists of ferrous trash, such as wire, bolts, nails, equipment parts, tools, and machine cuttings. The results, if the iron is not removed, are damaging to equipment having close clearances, explosions, or fire, En the case of flammable materials, production downtime losses, and contaminated products.

Jan 1, 1966