Search Documents

By A. Pavlides

The purpose of this work is to conduct a preliminary analysis of the spatial variations of the thickness of lignite layers in the area of the Amyndeo mine, and to estimate the lignite reserves of the mine. The reserves are estimated by the method of the Voronoi diagrams, using a group of mirror points to close the polygons around the boundaries of the mine. Two data sets are investigated. The first one corresponds to an exhausted part of the mine. The derived reserves estimates are compared with the actual data obtained by the Public Power Corporation (PPC) to validate the analysis. The second data set extends over the entire mine, and it is used to derive an approximate estimate of the total lignite reserves. A geostatistical analysis of the total layer thickness is performed. The experimental semivariograms are evaluated for both data sets in different spatial directions. Two possible theoretical models for the experimental semivariogram (the exponential and a novel Spartan model) are compared and discussed. An interpolated kriging map of the total thickness variation is produced accompanied by a map of the kriging precision. The performance of kriging interpolation is discussed in terms of cross validation measures.

Jan 1, 2007

By M. J. Virnig, C. P. J. Van Vuuren, A. J. Botha

The Zadra, AARL and organic elution processes and variations of them are presently widely used to recover gold from activated carbon. Despite this the study of the kinetics of elution have received relatively little attention. It is the aim of this study to investigate the rate processes taking place during elution in both inorganic and organic solutions. Batch adsorption and elution rate and equilibrium experiments were performed. The spatial concentration of gold inside carbon particles at various stages of the adsorption and elution processes were measured with a scanning electron microscope using an image analyzer to control and manage the micro-analysis data. The activated carbon particles exhibited film and intra-particle mass transfer rate- controlled behaviour during adsorption in a caustic aqueous solution at 95°C. Elutions in the aqueous caustic acetone solution at 30°C and the caustic aqueous solution at 95°C were unaffected by change in stirring rate. Elution was modelled by desorption reaction rate-control at the outer surface of the carbon particle. Adsorption and elution isotherms under duplicated solution conditions showed reasonable agreement for the inorganic solution and a large disparity for the organic solution.

Jan 1, 1993

By T. T. Chen, J. L. Jambor, J. E. Dutrizac

A reconnaissance study of the neutralization potential of 30 diverse minerals, 28 of which are silicates and aluminosilicates, has shown that most of these minerals contribute minimally to the neutralization potential (NP) in standard static tests. Feldspars in particular give low NP values and would not be expected to attenuate the acidity to any significant extent in acid rock drainage settings. The BET-determined surface areas of the minerals vary considerably, and the large surface areas of some of the pulverized samples have clearly affected the NP values even though the standard static-test protocol was used for the preparation of the samples. The low NP values of most silicates and aluminosilicates are in general agreement with the laboratory-determined slow dissolution rates for these minerals. The results suggest that, in the prediction of whether rocks will be acid-producing, the most realistic measure is that of the carbonate content. In mine wastes from metalliferous ore deposits, the contribution to the NP by the non-carbonate gangue assemblage is unlikely to be more than a token amount until well after the establishment of an acid rock drainage situation.

Jan 1, 2000

By Louise H. Michaud

An interactive mine planning system that employs recent advances in 3D computer graphics capabilities and 3D geologic modelling to aid with the tasks involved in producing dragline mine plans was developed. As well as offering large potential saving in the time required to carry out the planning tasks, the system offers immediate visual feedback to the planning engineer. This can greatly aid in the conceptual understanding of complex geology and mine plans. The package incorporates the generation of a three dimensional Gridded Seam Model (GSM) as the basis for the development of the geologic database. This modelling method is capable of accurately representing rugged topography and multiple coal seams, including folding and faulting. The GSM is then integrated with an interactive graphics mine planning system in order to develop one model and one database for the generation of the mine design, the depletion of the coal resources and the movement of spoil material. The gridded structure of the model also provides the foundation on which all mine and spoil pile volumes are calculated.

Jan 1, 1992

By Ryan Lindmark, Guoxing Gu, Zhenghe Xu, Jacob H. Masllyah

Induction time is often referred to the time required to form a stable three-phase contact between a gas bubble and a flat or droplet surface in a liquid medium. It can be used to quantify the attachment process in aflotation system. Various techniques have been developed to measure this important parameter. Due to its importance in flotation systems and other processes, significant advances in refining the induction time measurement techniques have recently been made. This paper summarizes these recent advances and describes a novel method developed to monitor bubble attachment to a pendant bitumen drop or bitumen-coated flat surface. This visualization-based method offers a higher sensitivity and accuracy than the previously developed apparatuses in the induction time measurement. As an example, the induction time for oxygen bubble-bitumen attachment was measured at a fixed bubble size as a function of temperature in two different aqueous solutions. The results showed that higher process temperature is favorable for oxygen bubble-bitumen attachment and hence bitumen flotation. Addition of calcium to the aqueous solution slightly decreased induction time.

Jan 1, 2005

Since first introduced, the coal mine roof rating (CMRR) has been widely accepted as a tool for geologic characterization and mine planning. This paper discusses the application of the CMRR to another practical ground-control problem: extended cuts. Extended cuts, i.e., cuts greater than 6 m (20 ft) in length, are commonly used with remote-control continuous miners. Extended cuts can greatly increase productivity, but they have been associated with a number of fatal roof-falls. When extended cuts are attempted in weak roof material, the roof may collapse before it can be bolted Until now, it has not been possible to predict where conditions may not be suitable for extended cuts. In this study, data on the CMRR and extended-cut experience were collected at 36 mines in seven of the United States. It was found that, when the CMRR was greater than 56, deep cuts were routine in nearly every case. When the CMRR was less than 37, extended cuts were almost never taken, and, when the CMRR was between 38 and 56, extended cuts were sometimes, but not always, feasible. The data also show that extended cuts are less likely to be stable if either the entry span or the depth of cover increases.

Jan 1, 2000

By T. X. Ren, J. S. Edwards

Although much work has been carried out in order to understand the mechanism of spontaneous combustion and hence minimise its potential risk, the spontaneous combustion of coal continues to be a problem in coal mining. The Department of Mineral Resources Engineering of Nottingham University has been active in conducting fundamental research into the problem of spontaneous combustion of coal. For years standardised adiabatic oxidation tests have been used to identify coals and other carbonaceous materials liable to spontaneous combustion. Recently the apparatus has been computerised and coupled with an expert system known as ESSH to evaluate the potential of self-heating of coal on the basis of intrinsic coal properties, geological settings and mining techniques. A numerical model has been developed to study the aerodynamics of airflow in the wastes of longwall coal faces. The Computational Fluid Dynamics approach is being explored to simulate airflow behaviour and nitrogen inertisation processes within the goaf. Such a model would be used in locating the areas most liable to spontaneous combustion and improving the utilisation of nitrogen. It would also be possible to determine the most likely path ways of combustion/heating products so as to provide an indication of the most appropriate locations for fire detectors.

Jan 1, 1997

By J. M. Dean, R. L. Grayson, N. P. Reddy, Y. J. Wang

This 1988 survey provided a cross section of computer software use by the US coal industry. From 1250 mailed questionnaires, 171 responses were received, representing a 4.9% sampling of the 3496 US coal mines. Since the distribution of responses by regional stratum matched well with the distribution of mines by stratum, the survey was given statistical validity. A statistical description details the computer use by region, mining type, organizational size, the level of application within the organization, the type of software application used, the variety of computers on which the software was used and the percent of users within engineering, management and general applications categories. Overall, 63.5% of the respondents use computers at some level in their organizations. All of the mines producing more than 454 kt/a (500,000 stpy) used computers. However, for those producing more than 9 kt/a (10,000 stpy) but less than 91 kt/a (100,000stpy), only 44% used computers. Generally, the software applications were still data-processing oriented. The application sophistication grew with increasing mine size. Computer system models and configurations for different sized organizations are recommended based on the configurations used in the industry at the time of the survey.

Jan 1, 1994

By Y. C. Kim

One aspect of long-range mine planning in an open-pit mine is first to define the ultimate pit limit, i.e., the projected size and shape of the pit at the end of its life. This chapter is concerned with various techniques that are currently in use today in determining the ultimate pit limits using the computer. Prior to the early 1960's, open-pit limits analyses were entirely performed manually. This manual technique has been well explained by Soderberg and Rausch in Surface Mining (1968). Soderberg and Rausch also explain clearly the need for establishing the ultimate pit limits in long-range mine planning, i.e., location of surface facilities, dumps, etc. Consequently, the need for ultimate pit limit design will not be reiterated here. Nor will the definitions of the most commonly accepted terminologies such as break-even stripping ratio, economic cutoff grade, ultimate and working slope angles, preproduction stripping, etc. be repeated here. Briefly, the objective of the ultimate pit limit design (which is also frequently referred to as pit design in short) is to determine the projected final pit limits of an ore body and its associated projected grade and tonnage, which will maximize some prespecified economic criteria while satisfying practical operational requirements.

Jan 1, 1979

By Liu Cheng-si

The number of control plans for placing control devices in a ventilation network is surprisingly large, but the research result indicates that not all control plans are feasible. The feasibility of a ventilation network control plan depends on two factors. One is the influence of the network structure. The structure must contain one independent variable-flow airway in a non-controlled loop. Otherwise, the control plan is unfeasible. The other is the combination of the air resistance, quantity, pressure and other parameters. Under some conditions, the selected values of these parameters may result in an unfeasible plan. As to the influence of the network structure, when the network structure is simple, the feasibility of a control plan can be judged directly. However, for the influence of the parameters, the feasibility of a control plan must be examined through calculation. The control position has been extended into the natural-splitting subnetwork from the conventional constant-flow subnetwork. This technique is theoretically significant. The extension of control positions results in a great increment in control plans and variation in parameters. At present, the calculation methods of the ventilation network control plans are all available. They are quite useful in selecting desirable plans. However, among the plans found, some are impractical or even unfeasible. If the unfeasible ones can be eliminated at first, much time can be saved in design and calculation. This also facilitates management and decision making.

Jan 1, 1991

By S. Henley

There is much in common between the requirements of open-pit mining and quarrying operations. Both involve the extraction of large volumes of material from surface excavations. The principal differences are of degree: open-pit mining of materials such as coal or gold generally involves the extraction of only small volumes of 'mineral' and large volumes of waste-they are operations with very high stripping ratios, and are made viable only because of the high unit value of the extracted mineral. In quarrying operations, the unit value of the mineral - sand, aggregate, limestone, or clay - is much lower, but stripping ration Are also lower. Thus the same techniques of geological modelling, reserve estimation, and pit planning are applicable, as is shown in two examples from the British quarrying industry. In each case, a primary requirement is the definition of production volume or tonnage. Sometimes, this need may be addressed simply by the use of a survey data processing package. However, in other cases, such as the two examples addressed in this paper, of sand and clay quarries, detailed assessment of the variation of mineral grades is a vital part of the exercise, and simple volumetric modelling cannot in itself be sufficient. In these cases, a block model approach using simple logical and numerical post-processing is also required to obtain required parameters for commercial classification of the products to be extracted. Pit designs themselves may be optimised by use of algorithms such as Lerchs-Grossmann, but the value of mineral produced can be dependent on factors other than its grade in any one part of a single pit, and the 'optimised' pit itself must be considered only a good sub-optimal. Given the right degree of healthy skepticism, and a software package with sufficient flexibility to be adapted readily to the rather different requirements of the quarrying industry, there is no reason why the quarrying industry should not benefit from the many years of investment in mining software technology.

Jan 1, 1989

By Michel Grenier, Gopal Kunchur, Stephen Hardcastle

This paper presents the findings of a dust study in a typical fluorspar processing plant. The primary purpose of this study was to identify employees and occupational groups exposed to high dust levels and determine compliance with personnel regulations for regular and extended work shifts. The range of airborne concentration of respirable silica and fluoride compounds in specific areas and on personnel was determined. State of the art dust monitoring equipment and tracer gas techniques were used to measure dust concentration, pinpoint dust sources and map major airflow trends in the mill. Results of the survey indicated silica dust concentrations in excess of permissible limits being produced mainly by crushers at the south end of the building. Tracer gas releases and gas chromatographic analysis further showed that prevailing south to north air currents tended to carry and spread dust produced by the crushing operations throughout the process plant. Airborne concentrations of fluoride compounds measured during the study were always well below the prescribed threshold limit value (TLV) for the contaminant. Recommendations, including a mechanical exhaust ventilation system on crushers and transfer points, scheduled preventive maintenance on existing bar sprays and wearing of personal protective equipment were made which significantly improved the work environment. Further testing conducted after Installation of the dust extraction system revealed significant improvements in most areas of the mill.

Jan 1, 1991

By Jerry M. Whiting, Samuel Frimpong

Superior ventures selection and the subsequent management of their development and production are crucial in the competitive environment of the upstream minerals and energy industry. An important element of this chain is the management of uncertainty and risk dynamics. In the world of faster and more complicated technological and environmental changes, international competition and commodity market dynamics, thorough and sophisticated valuation must be carried out to establish a venture's value and return on investment. Thus, managers and investors must use methods that respond to market dynamics, investment and feasibility study options and provide relevant information for strategic investment decisions. Conventional methods have no built-in procedures to help investors analyse these options. Modern financial methods based on the dynamic arbitrage theory overcome these and other limitations of conventional methods. In this study, dynamic arbitrage theory has been used to formulate 3D parabolic differential equations that govern the stochastic processes of a copper mining venture with ongoing feasibility studies. The alternate direction implicit algorithm is used to solve the numerical approximations of the differential equations and their boundary conditions. Phase dynamics of the venture have been analysed to provide investors the appropriate timing for strategic investment decisions. The study also shows the amount and value of appropriate feasibility studies required to maximize the value of the mining venture.

Jan 1, 1996

By T. Eisele, T. Weldum, G. Rajala, H. Walqu, S. Kawatra

The throughput and energy efficiency of comminution circuits is reduced when ore characteristics change, causing bottlenecks in some portions of the circuit while leaving excess capacity in others. The results of analysis of three years of daily grinding circuit operating data for a full-scale plant has shown that the location of bottle-necks in the circuit will change depending on the nature of the feed ore. The circuit tends to be limited by the primary mill capacity when the ore hardness increases, and limited by the secondary mill capacity with softer ores. Two methods are considered for shifting load in the circuit to relieve bottlenecks by taking advantage of excess capacity in other parts of the circuit: 1) Addition of supplemental comminution operations, such as high-pressure grinding rolls, to process specific size fractions that are not handled efficiently by the primary mill; and 2) Use of screens to shift grinding load upstream from the secondary mills back to the primary mills. In the case of the plant examined in this study, it was found that 58% of the time there was sufficient excess capacity in the primary mills that the throughput of the circuit could have been increased by using screens to shift the grinding load from the secondary mills to the primary mills.

Jan 1, 2004

By Jorge Gutierrez C.

CODELCO-CHILE, the world's largest copper producer, began an integrated study of the informatics situation in the corporation at the end of 1980. As a result, a five years strategic Systems Plan was elaborated and approved by top Corporate management. Main points in this plan were: a systems architecture with information integration to the top level management; a higher degree of information technology in the production areas, an optional systems development resources utilization and a high profitability of the plan itself. During the study phase a series of theoretical definitions were fixed and used as a basis for the plan's design. A "common systems" approach was chosen as the development strategy instead of corporate systems or separate divisional efforts. Top management should be highly involved in the revisions of the plan, as well as qualified users should be chosen as project managers. The systems architecture should grant the information integration to the corporate level, in order to support an integrated planning and administration environment for the corporation. A total of 15 projects were defined, involving 570,000 man-hours and shifting the development efforts towards the production and production services areas. The paper presents a critical evaluation of the whole process, showing its good and bad aspects and a positive global balance. It also points some suggestions and hints to any corporation who wishes to get involved in a similar experience.

Jan 1, 1989

By Mortimer J. Richardson

In the context of this session on "Practical Placer Mining," a projection of the present into the future first assumes that there is a future for Placers. The second assumption is that there is the combination of adequate reserves and a willing, mining investment source to finance placers. This paper will point out the opportunities on both assumptions, illustrating my positive position on the future of gold placers. In order to focus this paper more effectively, I have chosen GOLD as the subject mineral. However, it is recognized that much of the technology for exploring and mining gold placers has been applied to other alluvial deposits; including platinum, diamond, tin, and various industrial minerals (which are often referred to as "placers" though this contradicts historical definitions). Over the past 10 years I have presented several papers on the general subject of placers, most of which are listed under References. These have included topics such as exploration, evaluation, small-scale gold placer mining and decision-making, mining and processing equipment designs, and dredge-mining operations. In an attempt to identify the more promising, undeveloped placer potentials in the world I have usually mentioned the USSR and China but qualified them as being either inaccessible, or, politically difficult to obtain. However, with recent developments in the USSR, the obstacles appear to be somewhat diminished.

Jan 1, 1992

By A. E. Hall, D. M. Mchaina

This paper outlines a proposed research project to investigate secondary sulphide ignitions. Sulphide dust explosions have resulted in loss of production and considerable capital and equipment replacement cost in Canadian mines. The practical application of laboratory test results to actual mine situations presents a complex problem and is a field requiring immediate investigation. The factors contributing to the outbreak of sulphide ignitions are not clearly understood. This indicates a need for future research to study the influence of blasting parameters, exhaust temperatures, and dust characteristics on secondary ignitions at source. The aim is to establish realistic quantities for each of the parameters and develop a model that will incorporate field and laboratory quantities. It may be possible to predict outcomes of sulphide ignitions when the parameters are known. It is also planned to study the techno-economic feasibility of the preventive and control methods. One aspect of planned future research requires quantification of some terms by obtaining measurements of pollutant concentrations and size distribution of the airborne dust in an underground environment immediately after a main blast. A blast-proof aerosol sampling package to measure the source term will be designed. This sampling package will consist of a sampling section and a shield which will be capable of withstanding a blast explosion. The accuracy in measuring the variables and combination of variables will be the main focus in this proposed study.

Jan 1, 1987

A combination field and office study of mining districts in Southwestern U.S.A., conducted in 1949 - 1950 by United Geophysical Company, embraced all of the essentials for a successful exploration project including factors such as geology water, transportation and many more. Perhaps the best known of several high priority areas chosen from the study was the Twin Buttes or Pima District in Arizona, however, the Turquoise District also ranked very high on this priority schedule. Following the discovery of the Pima Mine in 1951 and 1952, United initiated additional preliminary geological, geophysical, drilling and claim location work in the Turquoise District, but stopped shortly thereafter, when ASARCO began adjoining competetive activity. During the summer of 1957, sometime after ASARCO abandoned their claims in the area, Minerals Exploration Company began intensive exploration in the Courtland-Gleeson part of the District. This program was terminated in 1958. Later Bear Creek Mining Company supplemented the discovery endeavor with their own program during the period 1960 through 1962. This paper summarizes most of the geophysical work done by all of the groups except ASARCO and is intended to complement the recent paper "General Geology and Some Structural Features of the Courtland-Gleeson Area, Cochise County, Arizona" by Mr. Otis McRae of Bear Creek Mining Company.

Jan 1, 1966

By A. Casuge, D. Lee, J. A. Finch, C. C. Sui

The adsorption of copper and lead und their subsequent xanthate uptake were compared at pH 3.0, 6.0 and 9.2 on both fresh and oxidized sphalerite. The extent of adsorption and the rate of adsorption were strongly dependent on pH, with the highest adsorption of Cu and Pb being at pH 9.2. In the presence of both Cu and Pb, Cu adsorption was enhanced and Pb adsorption was suppressed. The adsorption kinetics of Cu and Pb were characterized by two- and three-stage adsorption processes, respectively. The exchange ratio of Cu to Zn was about one and that of Ph to Zn was greater than one and varied with pH. The uptake of xarlthate on "activated" sphalerite was dependent on pH. The rnaximum uptake was found to be at pH 6.0 for Cu-activated sphalerite artd at pH 9.2 for Pb-activated sphalerite. A measure of "activation strength" based on inetal ion adsorption and xanthate uptake was introduced. The activation strength of Cu to Pb was about one at acidic pH, but it was higher at neutral (pH -6) and alkaline (pH -3) conditions. The oxidation of sphalerite decreased Pb and, especially, Cu adsorption and decreased xanthate uptake.

Jan 1, 2000

The trend in the U.S. coal industry in recent years has been a continuous increase in the percentage of coal produced by surface mining methods. Though the predicted energy demands promise a good market for coal, growing legal and environmental issues make the exploitation of a coal deposit by surface methods a difficult and challenging task. Major emphasis has to be placed on the development of integrated mining and reclamation schemes which enhance the possibilities of post mining land uses. Since no major breakthroughs are foreseen in the near future in surface mining equipment, innovative applications of current equipment must be developed. Draglines have been and are expected to continue as the primary earthmovers in surface mining of coal. A dragline simulation model has been developed which has the capability to analyze various deployment schemes such as conventional side casting, advance benching, and extended benching. The mathematical aspects of the model, the input data, and the output results are discussed with reference to an application in an operating mine. The model can be used to select a suitable dragline for given geological and mining conditions and to study the effect of alternative mining layouts and spoiling plans on machine production.

Jan 1, 1979