Search Documents

By V. L. Jr. Davis, F. L. Stanley, P. J. Bethell

Fwe 3 m (10 ft) diameter Microcel™ flotation columns were installed at Clinchfield Coal Company's Middle Fork preparation facility in order to reduce product ash and increase recovery and plant capacity. The Middle Fork facility is utilized for the recovery of fine coal from a feed stream that consists primarily of 1 .5 mm x 0 material. The columns replaced conventional flotation cells for the treatment of the minus 150 pm fraction while spirals are used to upgrade the plus 150 pm material in the plant feed. The addition of the column flotation circuit resulted in an increase in plant capacity in excess of 20 percent while reducing the flotation product ash content by approximately 7 percentage points. Flotation circuit combustible recovery was increased by 17 percentage points. This paper discusses circuit design, commissioning, and sparging system design. Circuit instrumentation, level control, reagent system control, performance comparisons with conventional flotation, and general operating procedures are also discussed.

Jan 1, 1995

By P. Bevilacqua, G. Ferrara

The paper discusses the problem of accuracy in the determination of the partition curve of gravity separation processes, which is strongly affected by both the sharpness of separation of the density analysis system used and the width of the density range selected. The problem is important when the density analysis of the separation products cannot be performed using heavy liquids, but has to be performed using heavy suspensions or using other systems such magnetogravimetric separation. The imperfect separation given by these systems and the use of large density ranges lead to the determination of apparent partition curves instead of actual partition curves for the process. In the paper the relation between apparent and actual partition curves is studied under different conditions through a simulation program. For different input data, special diagrams are given which, once the apparent partition curves and the sharpness of the density cuts are known, allow calculation of the actual partition curves and the related parameters.

Jan 1, 1995

By Franc Runovc

The service hoisting plant in the mining transportation is an installation serving for the vertical transport of material and persons. An adequate mathematical model is presented for simple evaluation of the project parameters where different plant designs and the ways of transport are take into consideration. The technical and economical optimization procedure is added to the basic mathematical model of the project. This approach enables on one hand the optimization of the reconstruction of the multi-purpose hoisting plants in order to suppress possible bottle necks, while on the other hand it enables the determination of such values of the parameters of the choice and of the operation that the sum of total expenses per a transport unit' becomes the lowest. The optimization procedure is designed in such a way that all numerical data of the optimum hoisting plant are printed out together with the graphical representation of dependencies of the fundamental parameters in broader optimization region.

Jan 1, 1992

By P. H. Williams

Experiences gained using computers in the mining and geological environment have shown that it is quite rare for a system or the data it stores to be truly stand alone. Just as the mining enterprise aims to have a smooth integration of operations from exploration through mining and extraction to sales, so it should develop all its information systems within an overall framework or architecture which covers the applications and data as well as the computer hardware and communications. This paper discusses methods of achieving such an architecture, and describes some of the benefits it can have on the development and implementation of information systems. The key aspects are the identification of the business functions and the data that they use, and ensuring that the IS plan supports the overall objectives of the enterprise. Hardware and communications policies should be based on the plans for the applications and data, rather than the reverse.

Jan 1, 1986

By George A. Desborough, Stephen J. Sutley, Reinhard W. Leinz, Paul H. Briggs

The mode of occurrence of metals in mine wastes is investigated using sequential extractions. Metals are extracted from some or all of seven operationally-defined phases: water-soluble, ion-exchangeable, carbonate, amorphous Fe-oxide, crystalline Fe-oxide, sulfide, and silicate. The quantity of metals extracted from each phase varies with particle size. The presence of jarosite (potassium end-member formula, KFe3[SO4]2[OH]6) influences the selection of the procedure for extracting the crystalline Fe-oxide phase. Anglesite (PbSO4) and cerussite (PbCO3) are extracted as several phases. Extraction results can be explained only in part by X-ray diffraction (XRD) mineralogy because of lack of specificity of the extraction procedures, relatively high XRD detection limits, and the presence of 40% XRD-amorphous matter in each waste. The increasing chemical strength of the sequentially applied methods provides a basis for judging metal availability, water-soluble metals being most available and silicate-bound metals being least available.

Jan 1, 2000

By P. D. Rao, D. E. Walsh

A pilot-scale study was performed to evaluate the potential for gravity concentration of gold from -13 mm (-1/2 in.) crushed ore from Ester Dome, AK. 9.04 t (9.94 st) of crushed ore were sampled and processed through a Pan-American jig-Wilfley table pilot plant. Plant products were sampled for assay and material balance calculations. Gold recovery through one stage of jigging and two stages of tabling was 17.4% at a concentration ratio of 615:1. Concentrate grade was 766.3 g/t (22.4 oz/st). The feed grade to the plant was calculated at 1.71 g/t (0.05 oz/st). Jig tailings, primary table tailings and secondary table tailings grades were 1.44 g/t (0.042 oz/st), 1.30 g/t (0.038 oz/st), and 5.47 g/t (0.16 oz/st, respectively. Significant coarse, free-milling gold values were shown to remain in the, jig tailings. Concentrate mineralogy is discussed.

Jan 1, 1992

By G. Van Weert, J. F. Breedveld

Both regular and Silver Impregnated Activated Carbon (SIAC) were studied for their effectiveness in removing WAD (Weak Acid Dissociated) cyanides from solutions at pH = 10. SIAC has already been shown to be effective in the removal of free cyanide down to 30 ppb or less. The present work deals with complexed cyanides. Zinc cyanide was used to represent the WAD component. At pH=10, in either batch or column tests it was not possible to lower the total cyanide in solution from either 30 or 8 ppm to less than 1 ppm, using SIAC, regular activated carbon as received, or after grinding. Silver (metal) impregnation of the carbon was not beneficial in the removal of WAD cyanide. However, when silver is added as silver ions (nitrate), the cyanide is adsorbed as silver cyanide in preference to zinc cyanide. The latter compound converts to zinc (hydr) oxide. This way, the cyanide concentration in solution can be lowered below 1 ppm, even when zinc cyanide is already adsorbed on the carbon used. A single exploratory test with added copper ions indicated a similar effect for that system.

Jan 1, 2004

By Jon P. Stone

The Automated Minerals Information System (AMIS) is an integrated data base system being developed to support the Bureau of Mines minerals information collection and analysis activities. The system facilitates cross-referencing and integration of domestic and foreign information from a variety of sources. The AMIS provides a central source of minerals information that is versatile and responsive to the needs of problem and policy analysts as well as supporting the needs of those involved in data collection and interpretation. As the AMIS becomes fully implemented, it will become an important tool in forecasting and assessing the impact of policy decisions that affect the supply and demand for minerals. The Bureau of Mines has long been the Federal Government's principal source of worldwide information on non-fuel minerals. Emphasis is placed on the analysis of mineral problems and policies as they affect the world's nonfuel mineral resources. To facilitate timely and accurate analysis, comprehensive data on 87 commodities are collected by various Bureau programs. Minerals information is made available through a number of periodic publications including the annual Minerals Yearbook and monthly Mineral Industry Surveys. These data collection and analysis activities have traditionally been supported by over 200 separate information processing systems. The Bureau of Mines has begun to implement a broad information strategy to provide a better response to the mineral problems and issues of the 1980's. The cornerstone of the Bureau of Mines information strategy is the development of the Automated Minerals Information System. When fully operational, we believe that the AMIS will provide the Bureau of Mines with the most comprehensive source of minerals information available anywhere in the world.

Jan 1, 1982

By B. J. Arnold

A coal's size distribution clay content and moisture content can affect its handling behavior. But the combined effects of these properties and the effects of other properties are not known. Research underway at CQ Inc.'s (formerly EPRI's) Coal Quality Development Center (CQDC) and at Iowa State University (ISU) will answer these questions as part of a four year project to develop a coal handleability index for utilities to use when specifying coals. This paper will present preliminary data from the first year of the project, which focused on obtaining data on the chemical and physical properties of carious coals and their measured handling properties. Additionally, size, ash and moisture analyses and shear test data for several coals used at one power plant will be presented along with correlations between these physical and chemical properties and the measured handling properties. These data lead to the conclusion that while moisture content is the most important variable, the amount of -44 µm (-325 mesh) coal fines is a significant factor in determining coal handling behavior.

Jan 1, 1992

By Jacques Deraisme

Geostatistics has been applied in many mining feasibility studies throughout the world during the last decade. Recently geostatistics has begun to be applied to the field of mining processes by attempting to aid in the definition of the best mining policy. For a feasibility study the grade-tonnage relationships give a reasonable order of magnitude estimate of the ore reserves within the deposit. But the reserves that will actually be recovered, will vary depending upon the mining methods and the technical means used. The profit earning capacity of the mining project is determined by a great many factors, such as for instance: accessibility of reserves to extracting machines, the haulage distance between the mine and the mill, the variability of produced ore (tonnage and grades) which could necessitate stockpiles or blending areas?

Jan 1, 1979

By A. T. Weber, G. T. Adel

Earlier studies on the hydrodynamic interactions between fine particles and air bubbles have shown that fine particle flotation can be improved by using small air bubbles. In the present work, microbubbles ranging in size from 70 to 250 microns have been used in a flotation column for the processing of fine coal. The performance of the microbubble column has been studied as a function of wash water addition rate, aeration rate, feed rate and column length to diameter (L/D) ratio. The information collected from these tests has been used to analyze column behavior and to develop scale-up criteria. The results of this investigation suggest that mixing within the column may not be as significant as bubble size and residence time in determining column performance. Improved recovery can be obtained by decreasing bubble size which increases the flotation rate constant, and also by increasing L/D which increases residence time for a fixed column volume. The increase in residence time with L/D is due to a decrease in the volumetric flow rate of wash water with column diameter.

Jan 1, 1988

By M. J. Shulman

The exploration geologist is frequently confronted with the problem of allocating his resources, i.e., exploration effort, among various areas. Although geologic, financial, and logistic considerations influence the allocations, no objective criterion is usually given that determines the optimal allocation. Maximizing the expected gain in information, subject to the constraint of a limited exploration budget, is used as the objective criterion to allocate airborne reconnaissance effort. The information function, I(x), quantifies the expected gain in information, where x is the scale of exploration. To calculate the information function, the following probabilities are required: the probability that an area contains a deposit; the probability that an anomaly is produced by the target; and the probability that an anomaly is produced by a barren area (false signal). Alternatively, the barren areas can be replaced by other targets. To illustrate the allocation method, the optimal number of line kilometers, i.e., the optimal line spacing per area, is determined for an aeromagnetic survey for iron in Egypt.

Jan 1, 1987

By F. Vincent, A. Boulet, M. Noaparast, F. Woodcock, A. R. Laplante

A novel methodology to estimate gold recovery by gravity is presented. It makes use of a population balance model which represents gold liberation, breakage and classification behaviour and applies pre-concentration and recovery data to gravity recoverable gold (GRG) to predict overall recovery. The methodology is designed for gravity circuits located in the circulating load of secondary grinding mills. Gold liberation is estimated by processing a sample of representative ore with a laboratory Knelson Concentrator (LKC) in three successive steps, each at a finer grind than the previous one. Breakage behaviour is represented by a matrix H, which redistributes GRG in the feed of the secondary mill in the various size classes of its discharge. Provision is also made to account for gold overgrinding, which decreases the overall amount of GRG. Classification, pre-concentration and recovery data are estimated from plant performance, and are represented by the diagonal matrices C, P and R. The methodology is demonstrated with case studies of greenfield, retrofit and optimization applications.

Jan 1, 1995

By Fikret Suner

Two rare evaporite minerals, nahcolite (NaHC03) and trona (Na2C03?NaHC03?2H20), are both widely used in the production of sodium carbonate (Na2CO3) The largest natural carbonate deposits (trona) are in Wyoming, USA, the second largest deposits are in Turkey, in a lacustrine basin (Beypazari) where nahcolite and trona are located within the Miocene Hirka Formation. The Hirka Formation is mainly composed of bituminous shale, claystone, marlstone, tuffltuffite, and dolomitic limestones. Although numerous trona beds are interbedded within the above mentioned sedimentary units, there are only two beds of trona that are of economic interest. The lower part of the lower trona bed is rich in double carbonates such as pirrsonite (NA2C03? CaC03?2H20) and gaylussite (Na2C03?CaC03?5H20), indicating a change in Ca/Na ratio in the solutions which are responsible for the formation of soda occurrences. In contrast, the upper part of the upper trona bed is rich in nahcolite. This minerological pattern has been found in every drill- hole in the basin. While both trona beds average up to 10 m (33 ft) thick, the average thickness of nahcolite is approximately 0.5 m (1.6 ft). Also, thin section studies show that many fibrous and lath-like trona crystals contain small radial nahcolite crystals; all of them are euhedral and equi-dimensional. Geochemical studies of major, minor, and trace element contents also support this coexistence. Macroscopic and microscopic observations reveal that the nahcolites principally were formed as a result of an incongruent dissolution process of trona. In conclusion, the presence of nahcolite in the Beypazari basin is due to the dissolution process of trona, particularly during the last stage of evaporation, as a result of fresh water entering the basin. During that time, an increase in the HC03/ C03 ratio resulted in nahcolite-trona phase transitions.

Jan 1, 2001

By J. C. Watts

Ball mill grinding circuit control has received increasing emphasis in the past few years due to such factors as declining ore grades, increasing production costs, and advances in analytical devices and minicomputer technology. Since ball mill circuits have been a traditional bottleneck in mineral processing plant throughput, control systems often improve through- put without requiring additional processing equipment. In addition, much of the variability of the grinding product size and consistency is often removed, allowing better process operation downstream. Among the problems which arise in designing and implementing a process control strategy for ball mill circuits are circuit constraints imposed by processing equipment and local management, proper instrument selection, installation and maintenance, and use of calculated or inferred variables for process measurements. This paper discusses these problems and attempts to identify valid approaches to their solution.

Jan 1, 1979

By C. L. Karr

Researchers at the U. S. Bureau of Mines have developed a technique for producing adaptive control systems using fuzzy logic and genetic algorithms. These controllers can be used to efficiently manipulate complex systems in real-time. Furthermore, they can achieve an acceptable level of control despite limited feedback in the problem environment. The control systems that result from the implementation of the Bureau-developed technique are able to recognize when changes have occurred in the problem environment, evaluate the magnitude of these changes, and alter the strategy being used to control the problem environment. Fuzzy logic is used to provide the controller with a rule-base that mimics the "rule-of-thumb" approach generally adopted by humans in the area of process control. Genetic algorithms are used to provide the controller with the adaptive capabilities necessary for the control of complex time-varying processes popular in the minerals processing industry. The effectiveness of this technique is demonstrated on a laboratory pH titration system. The pH system includes a changing setpoint, titrants with varying concentrations, and the possible addition of a buffering solution.

Jan 1, 1993

By Solomon S. Katz

As more and more computer software is written for geological mapping applications, the users of the software are discovering the problems of transferring data between the programs, maintaining correct data and integrating maps produced last week with those produced today. One way to deal with these situations is by using a geographic information system (GIs). Last September the USGS and National Academy of Science held a 5-day GIs symposium on integrating technology and geoscience applications (USGS, 1988). It was followed in October by GEOTECH '88 (Peters and Krajewski 1989) which had a session exclusively for GIs applications in the Geo-Sciences. Editorials in Geobyte (Leonard, 1986, 1988) suggested that geographic information systems will be the next major computer programs to be adopted by the mineral industries. As far- back is 1985, the Computer Oriented Geological Society (COGS) printed An Introduction to GIs in their newsletter (Katz, 1985). About 20 years ago, a revolutionary idea occurred in the world of business data processing. It was the idea that all related data be stored in a standard format, in a single place and that all related computer application programs would use the same data.

Jan 1, 1989

By M. C. Williams, T. P. Meloy

With the increasing power of computers to simulate and control processes in the mineral industry, predicting the potential use of computers in the minerals field is not a hazardous enterprise, but predicting the timing of their use is. Like the railroad industry, technology invades the mineral industry, rather than being an industry like electronics that creates technology. Because of this invasive nature of computer technology in the minerals field, this paper predicts what will be possible to do effectively and economically with computers in the mineral industry. Moreover, this paper explores the problems of using the emerging computer technology in the mineral industry. For example, if not now, it soon will be possible to control the output of a mineral processing circuit - high grade, high flow or a mixture of it - to meet the daily market conditions and to sell each day that daily "mill" output as "mill" futures on the commodity market. Finally, suggestions are made which may be done to prepare the industry for the computer revolution in the mineral industry.

Jan 1, 1993

By I. Iwasaki, T. Fujuita

The removal of phosphorus from steelmaking slags is essential for recycling such slags to blast furnaces for recovery of their manganese, iron, and lime contents. Phosphorus is mainly concentrated in the dicalcium silicate phase of the slags (Fujita and Iwasaki, 1988, 1989; Suito, et al., 1977). Slow-cooling of steelmaking slags in an air atmosphere increased the grain sizes of constituent minerals; however satisfactory magnetic separation results could not be attained because of the close association of a strongly magnetic ferrite phase with dicalcium silicate (Fujita and Iwasaki, 1988). Curie point of the strongly magnetic ferrite phase in the slow- cooled steelmaking slags was investigated and an attempt was made to separate the phosphorus-bearing dicalcium silicate phase in ground slag pulps heated to a temperature exceeding the Curie point. Materials and methods Slag samples, heated to its fusion temperature of 1370°C and slow-cooled in an air atmosphere, were ground dry to -90 µm (about 170mesh) in a ring grinder. The ground sample was pulped to 1% solids in distilled water using 1 kg/t sodium hexametaphosphate as a dispersant and separated in a Sala high gradient magnetic separator, Laboratory Model 10-15- 20B, using a 100-mesh expanded metal matrix and 300 m/h flow rate.

Jan 1, 1990

By Y. Zimmels, C. Feldman

Closed-circuit grinding processes are considered in the context of a reactor-separator circuit that involves multifraction streams and products. Because grinding circuits are low-efficiency, capital-intensive operations, modeling to maximize their economic return is appropriate. An attempt to develop and test such a model is presented in this work. The model relies on process simulation for both the mill and the separator, in conjunction with constraints imposed by product specifications. The grinding process was simulated using breakage functions, which provided complete data on the feed and product of the mill. A cyclone bank used as the separator was also simulated using known models. The overall process model provided a complete simulation of the multistream grinding and separation process. The process model was then incorporated into an economic model that predicts grinding cost, subject to process constraints, for a given set of operating variables. The model facilitates economic optimization of the grinding process as it relates to process variables and process hardware.

Jan 1, 1993