Search Documents

By Ian S. Lowndes, Adrian T. J. Moll

With the current trends towards the concentration of extraction to fewer but higher production units in deeper seams, often of higher coal rank, the role of methane drainage ranges has become critical. As mines exploit seams at greater depth and more remote locations there has been a need to extend the lengths of methane drainage ranges and to increase the capacity of the surface pumps. This trend has highlighted the need to effectively simulate the operation of a methane drainage range in order to produce the optimum design and operation of a safe and economic system. This paper describes the development of such an analytical tool. The application of this computer model is illustrated by the analysis of the operation of the drainage system of an extensive mine. The paper concludes by considering the development of a [Knowlege Based or Decision Support System] which will assist the ventilation engineer in assessing the current performance of an existing drainage range and will suggest possible remedial modifications or design strategies which may improve the system performance. INTRODUCTION In order to maintain the general body methane levels to below predetermined statutory threshold limit values (TLV's) on major longwall production units there are, for a given production rate, two major complementary control devices which may be employed by the ventilation engineer. These are the combined design and application of a competent mine ventilation and methane drainage system. The methane drainage system should be designed so as to maximise the capture of the methane (firedamp) from the seam being mined and the strata gas liberated in the vicinity of the extraction zone from gas bearing seams or other reservoirs of gas situated at above or below the mining horizon. The design fresh air quantity entering the face should ensure that under normal operating conditions the methane entering in the vicinity of the face is rapidly dispersed and dilute to well below statutory TLV's. The drainage system must therefore be designed to maximise the capture of the methane gas liberated to minimise the amount of gas which enters the ventilation airstream. GAS DRAINAGE The inherent dangers of methane emissions in mine workings have been a problem of concern to mining engineers for many years. To alleviate the risk, methane drainage has been employed for some years to capture the gas before it becomes a hazard to the operation of the mine. The method of drainage employed will be dependent on a number of factors which include the longwall mining method and production cycle employed, the characteristics of the coal seam being extracted and those of the adjacent gas bearing strata. The location of the gas bearing potential of the over and underlying coal measures must be determined. The gas bearing

Jan 1, 1993

By Hugh E. Cronin, Joseph J. Coluccio

The Columbia Slough Consolidation Conduit Project is a 12 ft. 0 in. inside diameter—15 ft. 4 in. excavated diameter tunnel, 8,300 lf. in length. The tunnel is divided in two parts a 4,460 lf. reach to the West and a 3,770 lf. reach to the East separated by a flow regulation structure in the middle. The project was built for the City of Portland, Oregon Bureau of Environmental Services (BES) by the Frank Coluccio Construction Company (FCCC) Seattle, Washington under a $22,600,000.00 contract starting in 1998 and completing the contract in 2000 at a total cost to the City of $25,448,000. An increase of 12.6% from the original contract. The tunnel was constructed in an alluvial sediment that ranges up to 1,500 feet thick. The sediment varies from ?ne silty sand and sandy silt (SM-ML) to coarse sand and gravel (GP-GM) with varying quantities of cobbles and boulders. Most of the tunnel was constructed above the water table although one reach of almost 1,000 lf. had water to above the tunnel crown. The contractor, FCCC, used a Lovat 15 ft. 3 in.900 hp shielded TBM with multiple doors (4) of variable opening to excavate and support the tunnel. Tunnel supports were 5 in. WF 16 lbs. per foot at 4 ft. spacing and4 in. Douglas Fir lagging. Tunnel excavation was worked in 10 hour shifts with additional equipment maintenance and repair on the off time. The original Geotechnical Design Summary Report (GDSR) established a baseline for contractual purposes of slightly over 5 boulders (between 12 in. and48 in.) per foot of tunnel. (Table 1) At the pre-bid conference, three test pits were excavated to approximately tunnel invert, one at each end of the project and one in the middle near the flow regulation structure. The test pits encountered a few boulders but did not seem to support the five boulders per foot (varied from one boulder per foot of tunnel to eight b/lf.). Subsequent to the pre-bid meeting and the test pits, BES issued any addenda which changed the baseline boulder quantity in the GDSR to 1.7 boulders per foot of tunnel (varied from0.2 to 3.5 boulders per foot) a reduction of 67% from the original baseline. It is interesting to note the two separate tunnel reaches and how they were evaluated in the GDSR. Originally the Eastern portion of the work was projected at5.08 boulders per foot of tunnel and the Western portion at 5.30 boulders per foot of tunnel for a variance of less than 5%. In the revised quantity the Eastern portion was projected at 2.01 boulders per foot of tunnel and the Western portion at 1.42 boulders

Jan 1, 2003

By R. Svensson

Mill linings play an important role in all comminution processes with tumbling mills. The selection of the lining profile and the lining material has a great impact on overall grinding cost and mill throughput. The cost of the lining itself is minor in comparison with media cost, energy cost and the value of the material produced in the mill. The total scope must be considered when mill linings are selected. This paper presents case stories and explains the technology behind: •Different lining profiles in rubber and steel. •Orebed magnetic lining. •Steel-cap rubber lining. Introduction Grinding mill liner life has been a subject of extensive studies. Performance of mill liners in terms of wear life and how it relates to lining material and profile is abundant in the literature. The most economical liner material and design has been selected based on "cents per ton milled". The evaluation of the effect of liner design on power and grinding media consumption which is a far more significant part of grinding costs, has been less comprehensive (Fig. 1). Lining materials Steel. The most commonly used lining material is steel, calculated on a volume basis. Steel linings have a long tradition and a number of alloys is being developed. The main families are: •High chromium white iron. •Cr and Ni white iron (NiHard). •High chromium martensitic steel. •High carbon Cr-Mo perlitic steel. •High carbon Cr-Mor martensitic steel. •Manganese austenitic steel. Steel linings can be successfully used in most applications. Rubber. Rubber linings were introduced 25-30 years ago and are today commonly accepted to be the most economical linings for secondary and regrind applications. Rubber linings offer long service life in these applications and generally [ ] outlast steel in wet applications, where corrosion is a factor on the steel. The cost relation between rubber and steel has changed dramatically over the years. In the past rubber was more expensive than steel, but today, the cost of rubber is close to half the cost of steel, calculated on a volume basis (Fig. 2). The present cost situation has made rubber linings an economical alternative in several primary grinding applications as well. The wear rate of rubber in primary applications is higher than the wear rate of steel, thus giving a shorter wear life. This can be compensated for by making the rubber lining thicker. The cost advantage of the rubber allows for this, but care must be taken not to jeopardize the grinding performance. Rubber, as a lining material, offers some distinct advantages over steel lining, such as: •Ease of installation and removal. •Safer to handle, less risk of injuries. •Faster replacement. •Reduces noise.

Jan 1, 1996

By I. K. Kapageridis

Digital photography combined with three dimensional models of topography, mining operations and restoration plans can lead to extremely realistic images and animations of the current and future states of a mine or quarry. The amount of work and the time required for the successful modeling of a mine and its restoration plan are surprisingly low nowadays. All this means that the visual impact of mining and quarrying operations can be easily assessed using common computer hardware and some dedicated software packages. LAVA Mining and Quarrying SA is a company committed to strive continuously for the highest possible environment protection at the company?s quarries. The pozzolanic rock quarry located at Xylokeratia is one of the company?s quarries on the island of Milos and the subject of the study presented in this paper. A thorough restoration plan of the Xylokeratia quarry is being completed by the company. For its purposes, a complete visual impact assessment study was performed at the Department of Geotechnology and Environmental Engineering of the Technological Education Institute of Western Macedonia. The procedures used in this study and the produced visual results are presented in this paper.

Jan 1, 2006

By Chen Bing Ching

Hsikwangshan mine is located at Lengshuijiang city of Hunan Province. It is a stibnite deposit. The orebody is gently inclined; its ore run is about 3 km in length and extends about 1.2 km along the direction of dip. The thickness of the ore body is non-uniform and varies from 1.5 to 20 m. The orebody is mined by room and pillar and cementation filling. The nine levels at the ore top have been mined out. At present, the mining operations are at the eleventh level. The mine ventilation system consist of three main fans which are installed in different shafts and are ventilated in parallel. The main fans can be connected to each other through comprehensive return air drifts. Two of the fans are located underground and the other on the surface. The general configuration of the ventilation system is shown in Figure 1. Because the operating areas are scattered and vary frequently as well, it is difficult to bring about air flow control. If the air flow cannot be varied with the variation of production in time, the air quantities are not sufficient in some areas and are excessive in others. However, it is also a problem to coordinate the three main fans with one another to obtain the optimum economic cost of operation. In order to make the air delivery fit the variation of production continuously to satisfy the ventilation requirement of the working faces and to reduce power consumption, we have made a great effort over five years to install an automatic control system for mine ventilation at the Hsikawangshan mine. The key part of this system is a microcomputer. The whole system consists of a console, which is located at the surface; the circuit network that is provided for signal transmission; air doors and ventilators at the working face; the scale air doors which are installed at the main branch airways; main fans and their speed regulating devices, as well as the sensors used for observing pressure, air quantities, temperature and the concentration of carbon monoxide, etc. This system can continuously telemeter the air quantities and carbon monoxide concentration in the main branch airways, air pressure, air quantities, electric current, the temperature of the bearings of the main fans, etc. According to the production air requirements, the system controls the ventilators or air doors which are located at the working faces and regulates the air quantity in the main branch airways. It can also choose the optimum mode of operation automatically, and regulate the rotating speed of the main fans to guarantee the least total power consumption while satisfying the total air quantity requirements. If abnormality of the observed results is discovered, the audible and flashing light alarm signal starts up automatically. The operating mode of ventilation equipment also feeds back to the control room and displays on the console. The configuration of control the system is shown in Figure 2.

Jan 1, 1987

By C. A. Rowland

Introduction Comminution efficiency, as measured by relating circuit performance to the consumption of energy and the time and money required, can be determined by the following comparisons: Theoretical efficiency: The theoretical efficiency is the actual energy consumed in a comminution machine compared to the theoretical energy required to perform the size reduction. Operating efficiency: The operating efficiency compares the operating work index of a comminution machine to the Bond work index of the ore, as determined from bench-scale crushing and grindability tests or pilot-plant tests. Economic efficiency: The economic efficiency is comparing income from production to predicted income. Key words: Comminution, Bond work index, Grinding, Crushing, Ball mills, Rod Mills. Theoretical efficiency In their book Process Engineering of Size Reduction - Ball Milling, Austin, Klimpel and Luckie (1984) stated that, "We have tried throughout this book to avoid the use of the term grinding efficiency because the degree of conversion of energy to useful size reduction is an ill-defined concept. In addition, the only efficiency, which is of real interest, is the meeting of product specifications at the minimum cost." The National Materials Advisory Board, National Re¬search Council (1981), in the abstract of a report titled "Comminution and Energy Consumption" stated that, "Up to 99% of the energy consumed in grinding these ores may be expended in the movement of machinery, with noise and heat the undesirable byproducts, thus leaving only 1% of the energy available for size reduction. Coupled with this is evidence that many of today's crushing and grinding techniques not only are antiquated but have little or no scientific base of understanding." Throughout the past 50-plus years, grinding efficiency has been referred to as being from 1 % to 10%. The measurable basis for these observations is difficult to establish, but they appear to be based on production performance compared to theoretical energy requirements for the work done. The theoretical energy requirements were determined from the energy required to break a single particle or a thin layer of monosized particles by compression or by a single impact from an impact-testing device. King, Tavaras and Middlemiss (1997), in a paper titled "Establishing the energy efficiency of a ball mill" described such a test. These batch single-breakage tests generally do not duplicate the continuous-breakage process in the comminution machinery used in ore concentrators. Operating efficiency The currently available crushers and grinding mills are fed at a controlled continuous flow rate, and they impart the breakage pattern needed to produce the desired size reduc¬tion. While theoretically inefficient, they are the most practical comminution machines available. The operation of this machinery is relatively simple and can be controlled with available control systems. The essential factors in determining the operating efficiency of comminution machines are energy, as consumed in the machinery, and the required energy, as determined from test work. Bond work indices, obtained from bench-scale or pilot-plant crushability and grindability tests are used in the following Bond equation (Bond, 1960) to determine the energy required to produce the required size reduction

Jan 1, 1999

By Bonn J. Macy, David A. Gulley, William A. Vogely

INTRODUCTION Some of the most famous and graphic environmental incidents have arisen from mineral extraction, including oil spills, the Reserve Mining asbestos tailings case, Kaiparowitts surface mining and coal combustion, and other environmental causes celebre. The remote location of much of the mining industry to some extent reduces the human health hazards from pollution, but often times the pristine locale in which mining is conducted provides a sharp contrast to the impacting industry. This prompts questions as to what the research literature says about the true costs and benefits of environmental compliance. We survey the state of this knowledge. Where possible, we discuss studies focused on mining and related industries, such as primary metals production. In many cases, how- ever, the studies pertain to the economy as a whole. For present purposes, the mining industry is defined as companies engaged in the production and refinement of minerals, including metals, fuels, and nonmetallics (e.g., phosphate, sand and gravel). There are several stages in mining, with environmental effects occuring at every stage. The exploration stage comprises the period from initial prospecting to the point where the deposit has been located and delineated in sufficient detail to permit development decisions to be made. Geophysical and geochemical surveys, diamond drilling programs, and exploratory stripping and excavation are activities that may be employed during this stage. Some forms of prospecting are relatively benign, al- though even airborne surveys and motor vehicles generate noise pollution. Roads and the passage of vehicles and equipment affect land surfaces and vegetation, and attract heavier backcountry use. Clearings, stream crossings, and borrow pits can lead to increased erosion and sedimentation of streams. Geological survey grids disrupt vegetation and appearance. Moreover, prospecting can involve the excavation and stripping of overburden, resulting in soil and vegetation disruption as well as in- creased sedimentation of streams and lakes. The effects of exploration are often temporary, and frequently less severe than for other activities. Nevertheless, exploration-related impacts vary with the intensity and type of exploration effort, and can be significant. During the development stage of mining, shafts are sunk, pits excavated, buildings erected, and transportation facilities established. Dust, noise, and other socioeconomic and environmental impacts are generated by the relatively large and sudden influx of people, equipment, and activity. Surface disturbance and solid waste are generated by development, and liquid wastes form when mines are dewatered. The extraction phase is associated with a variety of environmental impacts. These impacts may differ for surface and underground mines. In surface mining, surface disturbance is obviously a major consequence. Piles of overburden and waste accumulation mar land surfaces. Wind and water erosion tend to spread the dis-

Jan 1, 1985

By S. C. Sun

The grinding of coals for coal preparation has been studied extensively by previous investigators, but no similar work has been done on coal lithotypes (l-4). However, the different natural breakage characteristics of coal lithotypes have been recognized and utilized by the coal industry (5,6) to develop the Longway Burstlein process (7) for the concentration of macerals(8). The specific objective of this research was to determine the relative grindability of lithotypes, obtained from both anthracite and bituminous coals. An attempt was made to relate the findings, wherever possible, to the chemical and physical properties of the tested lithotypes. Another aspect of this research was to ascertain the size distribution and grindability of lithotypes ground at a various number of revolutions in a Hardgrove mill.

Jan 1, 1970

By Joseph W. Siefke

The Kramer borate deposit is located in the western Mojave Desert at Boron, California, about 100 miles northeast of Los Angeles (Figure 1). The deposit derives its name from the district in which it lies. Borax (Na2 B407.10H2O) is being mined from the Boron open pit to serve a major portion of the United States and world borate markets. This paper deals primarily with those geologic factors which affect slope stability in the overburden at the Boron open pit. Discussion includes slope failure history, slope monitoring techniques and the results of a dipmeter survey of overburden structure. Open pit mining was begun at Boron in 1957. The initial pit was successfully excavated at the recommended 1.5:1 (horizontal to vertical) slope in the overburden. During pit expansion in 1962, excavation of the overburden exposed beds dipping into the pit at +15 degrees and numerous high angle fractures associated with two intersecting fracture systems, the West Jenifer and Portal fault zones. Ensuing south and east wall failures indicated the need for more structural information in the arkose to establish better wall design criteria. Barnard and Kistler (1963) recognized that the many facies changes, faults and other variables in the Boron overburden make it extremely difficult to reduce prediction of slides to a simple arithmetical formula. Despite the difficulties and uncertain¬ties, special programs such as surface resistivity, refraction seismic and core drilling were conducted in an attempt to predict slope stability conditions and to gather geologic information. These early efforts while helpful, did not provide the necessary details of bedding orientations and fault locations which are of paramount importance in our slope stability program. A dipmeter survey in 1974 successfully measured these variables and data from that survey are instrumental in the design of slopes currently being excavated.

Jan 1, 1976

By Frederick Schwarz

At the El Realito project, Sonora, Mexico, the Luz del Oro joint venture has recently inferred a geologic resource of 400 to 800 kt of 2.5 glt gold potentially present in gossans, breccias, and veins. El Realito, under investigation for a dump leach, open pit operation, is located in the Sun Antonio Mining District where gold and silver veins and gold placers have been exploited since Spanish colonial times.

Jan 1, 1990

By S. Su, S. Natansohn

This report describes a process for tungsten recovery from Searles Lake brines and upgrading its concentration to useful levels. The method consists of a combination of a liquid-solid and liquid-liquid extraction step and results in a product stream containing more than l00g W03/1. This technique is also effective in substantially reducing the concentration of objectionable impurities in the tungsten product. An ion exchange extraction mechanism is postulated.

Jan 1, 1983

By Fred H. Lightner

The feasibility evaluation of the Borealis project of Houston International Minerals Corporation (HIMCO) was initiated in October of 1980. The operation of the Borealis Mine and heap leaching plant began in late 1981. In order to achieve the rapid development schedule several items were necessary: 1) Pre-planning of environmental requirements and early study of key issues. 2) Adoption of conservative design criteria. 3) Coordination and cooperation between HIMCO and regulatory agencies. 4) Adoption of specialized engineering and construction procedures. 5) Careful evaluation of owner project management philosophy.

Jan 1, 1982

By Raul Z. L. Cançado, Virginia S. T. Ciminelli, Roberto Galery, Armando C. de Araujo

Brazil is presently among the seven largest gold producing countries in the world. This paper discusses the evolution of gold mining through the history of Brazil. It also gives a general account of the present practices for mining, processing and extraction of gold. Flowsheets of some selected plants are presented. The environmental aspects involved with gold production are also considered.

Jan 1, 1987

By K. Y. Haramy, B. T. Brady

A scale-invariant theory of the strength and deformability, of rock masses in static equilibrium and at incipient failure is proposed The theory provides a rationale, for designing structures in rock. This paper presents results of experiments conducted by the US Bureau of Mines and presents theoretical methods to determine and interpret the in situ strength of rock masses using the borehole shear tester.

Jan 1, 1996

By P. Venkatsubramanian, D. R. Maneval

An insufficient hydrologic data base exists for most large and small coal basins in Alaska owing to the lack of need in the past to collect data. The runoff process is insufficiently understood which is complicated by specifically northern phenomenon, and the lack of understanding of hydrologic relationships in permafrost environment. This paper presents an understanding of the hydrologic effects of frozen ground and presents methods by which the influence of surface mining upon the hydrologic balance can be analyzed.

Jan 1, 1987

By N. Finkelstein, D. A. Hinckfuss

The large and compact but simple Bougainville Copper Limited flotation circuit has been in operation for 3-1/2 years. Discussion of problem areas encountered since start-up and remedies that have been implemented or proposed, form the main basis of this paper. Full cur- rent operational data is also provided.

Jan 1, 1976

By D. B. Jenkins, D. R. Taylor

Treatment of bentonite clay with mineral acids yields a modified clay product of high surface area and acidity that exhibits enhanced adsorptive and catalytic properties. A highly specialized segment of the clay industry based on this process has evolved into a worldwide business with a capacity of about 500 kt/a. This paper will present data on the chemistry, mining, manufacturing, and applications for acid-activated clays.

Jan 1, 1988

By R. Sawyer, M. Sadler, M. Holdworth

Greens Creek is a high grade Ag/Au/Pb/Zn deposit located in southeast Alaska. Maximizing the Net Smelter Return revenue from the fine grained mineralization is a dynamic process given changes in metal prices, smelting terms, ore grades and flotation characteristics. This paper discusses the evolving concentrate production strategy, and how it is affected by such factors as ore and concentrate specifications and by market conditions. Also described is the development of an on-line computer program that provides the mill operators with real time NSR data and a means for optimizing Net Smelter Return.

Jan 1, 2002

By Ryan Lemmon

Belt turnovers are commonly used in conveyors to rotate the belt so that the clean side of the belt contacts the return idlers. The belt turnover length has traditionally been sized on only the twisting stresses. However, belt turnovers are also subjected to bending stresses due to the weight of the belt. Although bending stresses have in the past been ignored, these stresses are significant and should not be neglected. This paper quantifies and presents a method for calculated twisting and bending stresses and also the belt sag.

Jan 1, 2002

By Heinz Hoberg, Fred Ulrich Schneider, Rudolf Diegel

The risk of contamination of dumped tailings and ground water by coal flotation reagents has been investigated by using the 14C-radiotracer method for adsorption and desorption measurements. The results indicate, that a high amount of the reagent components adsorbed on the tailings if there was no coal in the pulp. In coal flotation however a competitive adsorption behaviour could be observed, with the effect that only a low quantity of reagents adsorbed on the tailings. Mobilization tests showed, that only small quantities of reagents could be desorbed by rinsing water. Therefore the contamination of ground water should be low.

Jan 1, 1995