Search Documents

By G. Raspa

This article describes a procedure for calculating the recoverable reserves of stratified orebodies characterised by a thin and irregular layers. An application on the phosphate deposits in the N'Zeto region of the Popular Republic of Angola is also described. The procedure consists in building a block model of the deposit through the conditioned multivarial geostatistical simulation of small areal units. The recoverable reserves are then calculated and defined by applying to the model a selection processes based on measured geological/economic parameters taken from the drillholes: thickness of overburden and mineralised layers, economic grain-size fraction, grade. The procedure also takes account both of the geometrical constraints of the mining method and dilution. For reasons of confidentiality, a multiplier has been applied to the values adopted for the sampling data.

Jan 1, 1992

By S. K. Kawatra, T. C. Eisele

To reduce their sulfur emissions, many coal-fired electric power plants use wet flue-gas scrubbers. These scrubbers convert sulfur oxides into solid sulfate and sulfite sludge, which must then be disposed of. Currently, the major markets for scrubber sludge are for manufacture of gypsum products, such as wallboard and plaster, and for cement. However, the quality of the raw sludge is often not high enough or consistent enough to satisfy manufacturers, and so the material is difficult to sell. Other markets, such as paper manufacture and plastics fillers, have even more stringent quality requirements and will not accept raw sludge at all. In the work described in this paper, several reagents have been examined to determine their ability to selectively improve the flotation of the unreacted limestone contaminant away from the desirable products (calcium sulfite and gypsum). The most success has been achieved using a cationic collector, which shows a higher selectivity between calcium sulfite and calcium carbonate than do the anionic collectors that were studied.

Jan 1, 1995

By Maria C. Jaime

Optimization of the rock cutting performance plays a major role in the tunneling operation. For a given set of tool and cutting environment, rock fragments may be chipped away in numerous manners and it is crucial to understand and be able to predict the dynamics at the cutter-rock interface. This paper presents rational and realistic 3D finite element modeling of rock cutting where typical computational issues ?such as contact formulation, appropriate rock material response, mesh distortion, and crack propagation? are overcome. Cutting forces and failure mechanisms in this finite element analysis are successfully validated by laboratory single-cutter scratching tests in sandstone.

Jan 1, 2010

By Tso-Min Shih, Ching-Hua Liu, Chung-Jen Lin, Hsi-Chiang Fang

This paper presented herein, describe the special design of an open type coal dust explosion apparatus and the laboratory works for investigating the effectiveness of the parameters on coal dust explosion and the prevention of the propagation of the coal dust explosion flame. Coal sample which were taken from the San-Ying collieries, were passed through the process of crushing ,grinding and screening to get the required particle size, ranged from 40 mesh to 200 mesh under size for testing purpose, the rock dust spreaded on the surface of coal dust and water mixed with coal dusts were employed for preventing the coal dust explosion and the propagation of the explosion flame.

Jan 1, 1991

By G. L. Finfinger, F. E. McCall, A. A. Campoli, M. D. Zuber

Injecting pressurized water into a coalbed prior to mining reduces mining-generated respirable dust. Because of economic and geological barriers, water infusion for longwall dust control in the United States is now limited to the Pocahontas No. 3 Coalbed in Virginia. Water is pumped into the coalbed through underground boreholes that are drilled horizontally from the headgate toward the tailgate side of retreat longwall panels. This paper theorizes that the barriers to widespread utilization of water infusion for longwall dust control could be overcome by long-duration, low-pressure water infusion through vertical gob-gas boreholes. Currently, 43% of the 72 longwall mines in the United States employ vertical gob-gas boreholes. Computer coalbed-reservoir simulation suggests that one vertical surface borehole could infuse the same longwall panel area as four horizontal boreholes in the current water-infusion system for longwall dust control in the Pocahontas No. 3 Coalbed.

Jan 1, 1997

By Kai Nielsen

In underground mining coarse muck and large boulders lead to ineffective utilization of costly mining equipment, and extra expenses and delays caused by secondary blasting. Cost analysis in some Norwegian mines shows that these extra expenses may amount to 10% or more of total mine operating costs. A computer model has been developed for sensitivity analysis of underground longhole stope blasting. The basic idea of the model is : When increasing the blasting energy input and fragmentation costs, the fragmentation will be better. This will lead to cost savings for loading, hauling, secondary blasting and primary crushing. The blasting design giving the lowest overall costs will indicate the optimal practice. The model has been used with data from several underground operations in Norway. An example run with typical costs shows that the costs for drilling, blasting and secondary blasting are the most significant parameters in the optimization process.

Jan 1, 1986

By G. D. Criswell, F. Palkovits, J. M. Johnson

A paste technology investigation was completed for non-pozzolanic fly ash from Units 3 & 4 of PPL Montana’s Colstrip Steam Electric Station. The purpose was to assess the feasibility of converting from dilute slurry deposition of ash products to a system using thickened or paste ash to reduce excess water storage in the impoundment, reduce seepage losses, and increase storage efficiency. The investigation included laboratory and field testing to characterize the rheological, geotechnical and dewatering properties of the ash products, an assessment of potential seepage reductions and an evaluation of potential for increased ash storage capacity by modifying impoundment operating procedures. The studies concluded that the conversion project was feasible, cost effective, and permittable. Critical facilities for the conversion project are currently under construction.

Jan 1, 2004

By F. A. Kruse, R. J. Madrid, P. L. Hauff

Sub-microscopic gold grains in disseminated gold deposits in Nevada are often directly associated with the clay mineral illite. Delineation of gold ore-zones can be improved by accurate characterization of the associated illite varieties or polytypes. X-ray diffraction studies of clay minerals from several disseminated gold deposits demonstrate that illite polytypes reflect lateral and vertical zonation around the ore bodies. Polytypes act as geothermometers indicating temperatures of ore deposition and proximity to hypogene and supergene fluids. Visible/near infrared spectral measurements using a field-portable reflectance spectrometer provide a reconnaissance technique for mapping the in-situ distribution of illites. Changes in the visible/near-infrared reflectance spectra are observed as illites progress from the lower temperature, less ordered 1 M variety to the higher temperature 2M type. The combination of the reflectance spectroscopy with the X- ray diffraction data creates a powerful tool for detailed mineralogic mapping for gold exploration.

Jan 1, 1989

By Roshan B. Bhappu

In situ mining and extraction is one of the Frontier Technologies that is destined to play an increasingly important role in the recovery of metals and minerals in the future. This premise is based on increasing costs of labor and energy, increasing awareness of environmental considerations and decreasing ore grades in the United States. Up to now, in situ mining has been successfully applied to a few favorable situations for the extraction of some evaporites, copper and uranium. However, because of its unique technical, environmental and economic advantages, this versa tile technology will find broader applications for the recovery of above commodities as well as for others which are currently extracted by hydrometallurgical means. This paper traces the development of in situ mining and extraction; stresses its dependence on interdisciplinary science and engineering; discusses its theoretical, practical and economic aspects; and finally presents potential applications of this Frontier Technology.

Jan 1, 1985

By K. Hanumantha Rao, K. S. E. Forssberg, F. Su

The influence of reagents dosage, pH, temperature, and particle size on the kinetics of apatite flotation response from magnetite has been investigated. The first-order models characterizing rectangular distribution and fast and slow distributions (F-S model) of floatabilities gave an excellent fit to the results of apatite flotation when compared to other models. However, the latter model is found to be better than the former in the goodness of fit and also in the description of flotation performance. The kinetic parameters in the F-S model are estimated by using a nonlinear least squares fitting program. The ratio of fast and slow rate constants is observed to be an important parameter for identifying the optimum levels of the variables and to outline the selectivity between apatite and magnetite. The influence of collector dosage is realized from the model parameters by relating it to the fraction of slow- floating particles. An attempt has been made to describe the apatite flotation behavior with the determined model parameters.

Jan 1, 1999

By T. Negeri, Y. Breau, M. Plante, A. Orumwense

As part of a joint project on fine particle processing, sponsored by the Consortium de Recherche Minérale (COREM), Natural Resources Canada (NRCan) and Hydro-Quebec, two flotation plant circuits were sampled to identify and quantify the causes of mineral losses within several particle size ranges. Size distributions, size-by-size assays and global chemical assays (Cu, Zn, Fe, S) were determined for the major streams. Size distributions were measured in 13 classes by sieving, cyclo sizing (-45 µm), and laser beam diffraction analysis. BILMAT, a material balance computation software package, was used to optimise the sampling, to estimate the unmeasured variables, and to assess and improve the quality of the information generated. The methodology has been extended to correct cyclo sizer data and reduce discontinuities of up to 20% at the transition from sieves to cyclo sizer. The paper describes the methodology and the main conclusions emerging from material inventory of the flow sheets.

Jan 1, 2003

By J. Stachurski, N. A. Abdel-Khalek

The objective of this investigation was to compare the results of countercurrent, column cell flotation vs. conventional (mechanical) cell flotation for the cleaning of a sulfur ore (-0.5 mm, 27.43% S) and its discrete size fractions. The tests were carried out using diesel oil as a collector and alcohol as a frother. Generally, column flotation produced concentrates of higher grade. For example, column cell flotation produced a nonwashed concentrate of 65.3% S with a recovery of 84.1%. However, conventional cell flotation produced a rougher concentrate of lower grade (57.0% S) and higher recovery (92.5%). At a superficial-wash water velocity of 0.265 cm/sec, the column product grade increased to 76.4% S, with a slightly lower recovery (80.3%). However, a concentrate with a similar recovery but a lower grade (74% S) than that of the washed product was obtained after three cleaning stages with the conventional cell. The column gave superior results for the flotation of fine and ultrafine particles.

Jan 1, 1994

By R. Merwin, S. Hoff, A. Ellsworth, M. Zhao, X. Jiang

The choice of mill linings in comminution circuits is critical as it affects grinding efficiency, overall cost, and product quality. As a consequence, a variety of liners have been developed over the years in an effort to increase wear resistance, improve grinding efficiency, and reduce energy consumption. One particular type of metal magnetic lining (MML) was developed in China seventeen years ago and has since been installed in over 400 applications throughout the Chinese mining industry. Most recently, one set of magnetic mill liners was brought to the US for installation into a secondary ball mill used for the grinding of iron ore. Protection of the mill is provided through the magnetic attraction and retainment of worn media, ball chips, and other various magnetic particles to the mill wall. This greatly improves the wear resistance and overall life of the liner. The installation and performance data for the magnetic mill liners in a US iron ore concentrator are presented in this paper.

Jan 1, 2007

By Jan Walaszczyk

The paper concerns the calculation of stresses and displacements in working area of room-and-pillar mining system of cooper ore mines. A three-dimensional rock mass model based on the finite element method has been developed. The complete strain-stress characteristic for pillars has been applied, but for the purpose of modeling the curve has been approximated by three segments of lines: - the first represents a behavior of pillar before a failure, -the second corresponds to a progressive pillar failure phase, - the third represents the part of the curve, where the increase of strains do not cause the stress changes, and it is called the residual strength. The criterion of model stability has been derived, which can be useful for predicting rockmass stability. The programs have been built, which allow to calculate stresses in bar elements, displacements in plate nodes, and estimate the stability of the model, which consists of plate elements and one-dimensional elements with a segment strain-stress characteristic. The programs were used to consider two different problems, which are connected with mining design and the exploitation systems.

Jan 1, 1992

By J. P. Barbosa, R. V. V. Araújo, R. B. E. Trindade

Bromide stabilizes the auric or aurous ion by forming a stable complex in acidic aqueous solution. The oxidizing agent normally used for the process is bromine, which is a corrosive liquid with high vapour pressure. This is, in fact, the main reason why it has not found acceptance yet as an industrial oxidant for gold. Ferric ion with hydrogen peroxide and/or sodium hypochlorite have already proved to be effective oxidants for the dissolution of gold from a rotating disc in a bromide-containing aqueous solution. In the present work, preliminary tests with four selected ore samples were tested to evaluate the dissolution of gold with the same system already tested with the rotating disc (Br-/Fe3+/H2o2/NaCIO). Compared to the conventional cyanidation, results were superior in one instance only. The major obstacle seems to be the maintenance of a suitable potential to allow the complex formation. However, the studied system may be interesting, is in some situations it may yield better results than conventional cyanidation; therefore, further investigation seems to be worth doing.

Jan 1, 1995

By Dilip K. Sinha

In the paper some interesting cases of applications of Operations Research and Computer Methods as worked out by the author and accepted by the management of some of the newly formed Indian mining organisation for implementation are highlighted. The main emphasis on the application cases was to use simple techniques and methods which yield the result in shorter time period, The case problems mainly deals with the production system optimisation in unit mines, areas/divisions and at the corporate levels. Also the management decisions regarding reorganisation of transport and distribution system of material and mineral are attempted to be optimised. Further, the case of management system development with computer aided decision making worked out for single large Iron Ore Project captive to a steel plant is outlined. Finally, the case of a large mining company having decentralised units and divisions geographically dispersed throughout the country, computerised management decision-information system designed on the basis of inputs and outputs of decision models relevant for different levels of management in the organisation is depicted.

Jan 1, 1986

By K. A. Natarajan, J. M. Modak, B. Saha

Nonliving waste biomass consisting of Aspergillus niger attached to wheat bran was used as a biosorbent for the removal of copper and zinc from aqueous solutions. Copper and zinc uptake by the biomass obeyed Langmuir isotherms. The binding capacity of the biomass for copper was found to be higher than that for zinc. The metal uptake, expressed in milligrams per grain of biomass, was found to be a function of: •the initial metal concentration (with the uptake decreasing with increasing initial concentration), •the biomass loading (with the uptake decreasing with increasing biomass loading) and •pH (with the uptake increasing with increasing pH in the range of L5 and 6.0). The metal uptake was significantly affected in the presence of a co-ion. The uptake of copper by the biomass decreased in the presence of zinc and vice versa. The decrease in metal uptake was dependent on the concentrations of metals in the two-component aqueous solutions. The effect of copper on zinc uptake was more pronounced than the effect of zinc on copper uptake.

Jan 1, 1997

By C. Haycocks

In spite of the increasingly high capital investment required for longwall mining equipment, there continues to be a steady trend towards this form of mining. This move is caused in large part by improved productivity of longwall mining systems combined with greater percentage of coal recovered over room and pillar mining, reduced manpower requirements, and the inherent safety of the system. Longwall mining is most amenable to the greater depths experienced by many mining operations, particularly in the coalfields of the Eastern United States. Two primary problems in the installation of a longwall panel are determining whether a particular seam is suitable for longwall and, secondly, type and capacity of equipment required for such a mining operation. In addition, recent legislation has forced an evaluation of the surface effects of longwall mining with a view to determining what, if any, surface damage might result from extracting any particular panel. These factors must be determined using large and often complex quantities of geological, structural, mining, and surface data. This makes the problem most attractive to solution using the computer.

Jan 1, 1979

By Otis M. Clarke

Observations of the land surface show that subsidence over active and abandoned underground mines is controlled to some extent by the stratigraphic and structural geology of the mines in addition to the methods of mining and the thickness of the seam mined. Exposures in highwalls of surface mines that intersect abandoned underground mines in the Warrior coal basin of Alabama illustrate this, showing sandstone beds that act as beams bridging openings and interbedded shale beds crumbling. Stratigraphic changes observed in the district are extremely variable and calculations regarding subsidence used for one area will not apply to another area if there is a major change in rock types Rocks exposed in road cuts and open pit mines demonstrate a marked difference in weathering characteristics. Some rocks, such as shale, wea- ther very rapidly, by crumbling and becoming plastic, whereas other rocks, such as sandstone, resist weathering. The continuing rock weathering after mining in openings produced by the mining activity and in fractures caused by roof movement, apparently, is a major cause of the surface sub- sidence that may occur years after the mines are abandoned.

Jan 1, 1986

By S. Majumder

The longwall face supports are provided to prevent the caving of the immediate roof at the working face. The thickmess of the immediate roof may be obtained from the working height and the average bulking factor. A strong bed, capable of withstanding maximum bending moment among the beds within the above roof, can be identified. The load on the strong bed may be obtained by finding out the overlying beds that will rest on the former during sagging. The limiting span, L, for this unsupported loaded bed, as a beam with built-in ends, can be calculated. The support density required at the supported span (face to goaf edge), a, during the first fall, is now estimated with a view to have a safety factor 2 at the face end, when bending failure occurs at the barrier end. However, the above value is inadequate to provide necessary safety margin against bending failure at the face end, during the subsequent cavings as cantilever, for L/a less than 20.6. d For the latter case a separate expression is derived.

Jan 1, 1986