Search Documents

By M. C. Williams

The dynamic behavior of batch mill, CSTR mill, and a closed grinding network consisting of a mill, sump, and cyclone was analyzed using the dynamic population balance model (PBM). The dynamic solution of the PBM of a batch, CSTR and a closed grinding network consisting of a mill, sump, and cyclone forms the basis of the dynamic analysis presented here. Two numerical dynamic solution approaches were used. These are: 1) providing additional constraints on breakage selection functions or 2) performing the Arbiter-Bhrany (or other) normalization of the selection functions. Actual experimental anthracite batch grinding data was used to obtain the functionality of the batch dynamic mill selection and breakage functions for a real physical system. The Levenberg-Marquardt algorithm for systems of constrained non-linear equations is used to solve the batch dynamic PBM grinding equations to obtain the grinding selection and breakage rate functions. The mill, sump and hydrocyclone were modeled as a CSTR operating at various retention times. Batch dynamic PBM data was used to provide the mill kinetic and breakage selection function data. Different dynamic solutions were obtained depending on the numerical approach used. Each solution approach to a dynamic PBM with transport, while giving the same prediction for a single batch grinding time, gives different solutions or predictions for mill composition for other grinding times. This fact makes dynamic nodal analysis and control problematic. The fact that the constraint solution approach gives a solution may suggest that normalization for closed networks is not necessary. Differences in solutions to the PBM cannot be excused away by inaccuracies in the data used to model the grinding phenomenon.

Jan 1, 1995

By Steve Hicks, Zach Agioutantis, Greg Hasenfus, Zach Wedding

Most prediction methods used to calculate mining-induced subsidence rely on empirical formulations, which typically assume flat topography and uniform properties in the overburden. It is also well known that when a longwall panel mines below a valley bottom surface ground deformation magnitudes and orientations may be significantly influenced by the presence of the valley. This paper discusses ground deformation data collected at different surface locations above the Buchanan mine in the eastern United States. Measurements at individual surface points and strata movement measurements using a three-point extensometer have been collected as the area was undermined. Measurements correspond to the mining of the panel immediately under the measurement points and to the mining of adjacent panels. Measurement locations correspond to valley bottom locations. The measurements are critically evaluated and compared with respect to topography and panel face location. The issue of the fluctuation of GPS measurements is also discussed.

Jun 25, 2024

By A. Bruynesteyn

I would like to talk to you today about microbiological leaching or, the solubilization of metal values due to the action of Thiobacillus ferrooxidans. Bacterial attack of sulfide minerals has been going on for centuries but only recently was it discovered that the acid and iron often found in coal mine drainage is produced by bacterial action on the iron sulfides in the coals. Not until 1950 was it proven that bacteria were playing a role in the dump leaching of sulfide ores. B. C. Research became involved in microbiological leaching in 1955 while examining mine drainage from the copper-zinc mine at Britannia Beach, north of Vancouver. Since 1955, B.C. Research has maintained a continuous re¬search program on microbiological leaching which, due to its applied nature, was put under industrial sponsorship in 1962. Most of the information pro¬vided in my talk today has been gathered under this sponsored research program and I would like to express our appreciation to the many sponsors who have made our work possible.

Jan 1, 1970

By Leo J. Miller

Sulphur deposits occur within the upper Salado and Rustler gypsum beds. The formation of a sulphur ore deposit requires large quantities of oil and /or gas, which must find a permeable pathway into the gypsum beds. The Permian beds weathered for 90 million years in an arid environment prior to the advent of a more humid climate at the beginning of the Cretaceous Period. The first Cretaceous rivers enlarged the sinkholes and caverns of the Karstified Permian terrain and deposited coarse conglomerates and sands into the subsurface gypsum beds. The resulting network of caverns and sinkholes, filled with permeable sediments, permitted the free flow of hydrocarbons through gypsum. All sinkholes and caverns infilled with Cretaceous sediments that have penetrated beds of gypsum are associated with sulphur deposits. The Castile gypsum lies directly upon the oil bearing Bell Canyon formation. Sinkholes and caverns filled with Cretaceous sediments occur in the lower Castile. Biogenic calcite and sulphur are adjacent to these sediments. However, faults assume the major role in generating the initial permeability, allowing hydrocarbons to penetrate the lower Castile gypsum. The largest faults are associated with biogenic calcite and sulphur for a distance of 250 meters up from the bottom of the Castile gypsum. It is apparent that two dynamic geological processes are generating permeability within the gypsum beds: (1) the Cretaceous sands decending with difficulty into gypsum and (2) the faults creating permeability in the lower Castile but losing energy through soft bed deformation in the overlying gypsum. Both of these sulphur ore controls are mappable, but another large sulphur deposit of the magnitude of the Culberson Sulphur Mine has yet to be discovered. It appears that massive sulphur deposits are associated with the largest scale examples of each system, that is (1) high densities of deep sinkholes and separately

Jan 1, 1992

By Richard E. Hucko

The U.S. Department of Energy (DOE) Coal Preparation Program focuses on providing the technical and process-development basis that can be utilized to produce environmentally acceptable clean-coal feedstocks for use as market conditions permit. A major objective of the Coal Preparation Program is the development of physical coal-cleaning technologies capable of significant removal of mineral matter and pyritic sulfur at high energy recovery levels.

Jan 1, 1989

By Rustu S. Kalyoncu

Rainbow colors of roofing granules, adorning the roofs of buildings from single family units to largest office buildings, have their origin in the roofing shingles as burlap soaked with tar appearing as early as the 1700s. Dusting of talc and mica on the coated surfaces, to keep roofing from sticking to itself in storage, represents an early improvement to the original construction product. Sometimes, colored, natural mineral dusts were added as color pigments within the dusting material, for initial color. Prolonged exposure to sun caused the asphalt to become brittle, and it eventually cracked and leaked. Search for solutions to cracking and subsequent leaking problems eventually led to the use of crushed mineral granules on asphalt coated shingles. This provided the impetus for further growth in the asphalt roofing industry. Application of a layer of crushed mineral on the asphalt coating minimized the coating deterioration from exposure to ultraviolet light, thus significantly improving the shingle life. In the 1900s, screened waste from slate quarries was the most commonly used granule in asphalt roofing products. Records indicate the use of coarse slate screenings for asphalt roofing as early as 1906. As the asphalt roofing industry further developed, other naturally colored minerals, such as silica sand, quartz, mica, feldspar, talc, slag, granite, rhyolite, and oyster shells were used on roofing surfaces. Later on, a number of manufactured granular materials, such as crushed brick and tile, fire clay, and white porcelain were used. The first artificially colored roofing granule was produced in 1914 by running molten slag into a solution of alkaline metal silicate, which was absorbed by the porous slag. Various colors were obtained by adding pigments to the silicate coating and by subsequently heat treating the granules. In 1922, another technique was developed in which green slate granules were saturated with copper sulfate solution and heated to 760°C to form copper oxide. Since then, many other granule coloring processes have been patented, one of the most significant being the sodium silicate coatings introduced around 1975. Granules as used in construction (specifically roofing materials) are defined as natural or synthetic-mineral grains smaller than gravel and larger than sand in particle size. They are used primarily for protective and decorative purposes on the weather- exposed surface of asphalt composition roofing. Development of artificial coloring techniques has made it possible for the roofing industry to provide asphalt roofing shingles in a wide variety of colors complementing the color and style of buildings. Roofing granules, as we see today, are the products of long technological evolution.

Jan 1, 1994

By Gregory E. Korbin

The effectiveness of pre-reinforcement as an immediate stabilization measure as well as its contribution to the permanent stabilization of a tunnel were studied through the use of physical (Figure 1) and numerical models (1). Physical models were designed for the investigation of two pre-reinforcement systems: first, reinforcing far ahead of the main excavation (Figure 2); second, spiling reinforcement ahead of the face (Figure 3). In both cases, the use of reinforcement was responsible for permanently stabilizing an otherwise unstable opening. Data from the physical models were used to calibrate a numerical model from which additional information on long term behavior, methods to account for the capacity of a pre-reinforcement system, and the mechanisms involved were ascertained. These studies indicated that pre-reinforcement can stabilize a rock mass effectively as it reduces deformations and thereby deterioration due to strain softening, provides rock mass confinement leading to increased available strength, and maintains rock arch continuity allowing for increased tangential stress in the immediate vicinity of the opening. Field studies verified the capacity of spiling reinforcement to restrain initial deformations.

Jan 1, 1976

By Richard B. Berg

California was a major talc-producing State until the late 1980s when production from the deposits in the Death Valley area ceased because of a number of factors which included pressure to discontinue mining in and around Death Valley National Monument, and health concerns affecting markets for tremolitic talc. The states of Montana and Texas now account for slightly more than half of U.S. talc production. Deposits in an area encompassing southern Death Valley and extending east into the Kingston Range were formed by contact metamorphism of carbonate beds in the Precambrian Crystal Spring Formation next to Precambrian diabase sills. These deposits contain ore ranging from high-purity, fine-grained talc to platy, tremolitic talc with high brightness. Deposits of tremolitic talc and talc schist in the Silver Lake District in San Bernardino County resulted from metamorphism of Precambrian carbonate beds intruded by granitic plutons. Northeast in Esmeralda County, Nevada hydrothermal alteration related to Late Jurassic plutons caused talc replacement of Precambrian to Early Cambrian dolomite. A hydrothermal origin is also indicated for talc deposits in the lnyo Range just north of the Death Valley District where bodies of unusually pure talc occur in Paleozoic lime- stone near Jurassic granitic plutons. Talc is now mined from a deposit in the foothills of the Sierra Nevada Range southeast of Sacramento where quartz-mica schist of the Permian Calaveras Formation has been hydrothermally altered to talc. Replacement of magnesite of the Precambrian Allamoore Formation produced talc deposits mined in the Allamoore District of west Texas. This dark-gray talc of low iron content with carbon- aceous material and dolomite is ideally suited for use in ceramics where it makes a white product when fired. Small bodies of platy light-pink to white talc suitable for use as an extender in paint are also mined in this district. In the Llano District of central Texas talc has replaced impure carbonate rocks and serpentinite. All Montana talc production is from deposits in the southwestern part of the State that formed by Precambrian hydrothermal alteration of dolomitic marble. This alteration produced material with high purity that ranges from very fine-grained, massive talc to coarser grained, foliated talc. Markets include pitch control in paper, paint, cosmetics, ceramics, rubber and plastics. In southwestern and northeastern Oregon, talc has replaced serpentinite in the vicinity of Mesozoic plutons. Soapstone for carving is mined from a southwestern Oregon deposit. Deposits of similar origin occur in central and northwestern Washington.

Jan 1, 1995

By David Newman

Multiple seam underground coal mining is ubiquitous in Appalachia. Many coal properties have from two to ten or more economically mineable coal seams. Because of the ability to penetrate 600-feet to 1,000-feet or deeper into the mountainside leaving panels of web pillars separated by barrier pillars, highwall mining is a hybrid between surface and underground mining. As a result, many of the ground control problems commonly associated with multiple seam underground mining exist with multiple seam highwall mining. These include: i) multiple seam interaction between web and barrier pillars in superjacent mines, ii) subsidence and caving propagating to overlying seams and mines, iii) pooled water and the potential for inundation resulting from a breakthrough between an active highwall mine and abandoned underground mines in the same or superjacent seams, iv) the presence of overlying or underlying mine workings where pillar columnization in the active mine is not possible, and v) the question of whether to mine ?top-down? or ?bottom-up.? Case histories are presented from southeast Ohio where the Middle Kittanning No. 6 and Lower Kittanning No. 5 seams are successfully highwall mined with 20-feet to 40-feet of largely shale interburden. A highwall miner was caught in a highwall collapse in the Middle Kittanning No. 6 seam when it was overmining auger workings in the Lower Kittanning No. 5 seam. Multiple seam interaction caused by the overmining transferred overburden stress onto the Lower Kittanning No. 5 seam. The overburden concentrated through web pillars initiated auger web pillar failure, resulting in roof collapse and subsidence in the Lower Kittanning No. 5 seam that propagated up to the Middle Kittanning No. 6 seam. A second case history involves multiple seam highwall mining in southeast Kentucky. The A3 Rider, A3, B2, and C1 seams are being highwall mined around abandoned underground mines in the A3 and B2 seams and augering in the A3 Rider. Because of spoil storage constraints for the surface contour mines, the highwall miner follows the active pits in each seam so a standard sequence of ?top-down? or ?bottom-up mining does not exist.

Jan 1, 2009

By Tom F. Deems

The term ball clay is applied to plastic sedimentary clays that have a high content of kaolinite and that possess white firing properties and high green strength (Mitchell and Stentiford, 1973). However, the name ball clay is not derived from any specific property of the clay. Instead, it comes from the original method of production in southwestern England (Scott, 1929). From open pits, the clay was cut into cubes with hand tools. The sides of the cubes were about 220 to 250 mm (9 to 10 in.) and weighed 14 to 16 kg (30 to 35 lb.). The eventual rounding of the corners with handling before sale gave rise to the term ball clay. Ball clays provide the workability and green strength required by the whiteware section of the world's ceramic industry. The main applications are in the sanitaryware, tile and tableware sectors. Each, though, requires particular technical properties in the ball clay component. The clay has to be as white firing as possible for all applications. However, for sanitary-ware, the rheological properties are most important. For tableware, fired whiteness and freedom from specking are the main criteria. Tiles need a reasonable green strength but the clay also needs to be cost-effective. The technical properties of the individual clays in any deposit depend on the clay mineral assemblage. This, in turn, depends on the geological formation of the deposits. Hence, it is the latter that largely determines the market sector for which the clay blends from a particular deposit are suited. Formation of ball clays Ball clays are formed from three main components - kaolinite, micaceous minerals and quartz - while carbonaceous material is also often present. The crystallinity of the kaolinite and mica varies. There are also occasional minor occurrences of feldspar, chlorite, montmorillonite andmixed. layer minerals. Marcasite, siderite and anatase also occur in small amounts. The properties of the clay depend on its mineralogical composition and its particle size distribution, particularly in the lowest size ranges. The original source rocks and the environment of deposition of the clay are the controlling factors. The importance of weathering processes in the formation of ball clays has long been recognized (Bristow, 1968). The diversity of source rocks produces considerable variation in the clay minerals formed. Therefore, each deposit is unique, with time-related variation within it. The greatest development of a weathering mantle takes place in a tropical climatic environment. Plant remains confirm that most ball clay deposits were formed under hot and wet conditions. Sedimentation of the clays had to be in fresh or low salinity water or clay minerals detrimental to whiteware manufacture would have been formed. Fresh water traps for the ball clay, sand and lignite sequences depended -on tectonic features, such as basin development along fault zones or lakes and lagoons on the edge of a large scale embayment. These factors for Devon ball clays were discussed by Vincent (1983). The combination of suitable source rocks, tropical climate, significant fresh water sedimentary environment

Jan 1, 1997

By William R. Wayment, Wayne S. Cusitar

INTRODUCTION The process of mining removes valuable and eco¬nomically recoverable minerals from the earth. In the case of hard-rock mining, this process involves breaking and removing ore, while leaving the waste rock or host rock as intact as possible. Prior to mining, ground stresses exist in the ore and the host rock as a result of weight and tectonic forces; for the purposes of this chapter, the ore is considered to support the host rock on both the hanging and footwall sides. Two basic phenomena accompany mining. First, the hanging walls and footwalls tend to move together as the ore is removed. Second, high stress gradients de¬velop in the rock periphery of the opening; the magni¬tudes of the stress gradients vary widely, depending upon the local geometry and conditions. At various times, mining methods have used square¬set timbers, waste-rock backfill, alluvial sand fill, and tailings backfill materials, with or without cement, to replace the loss of support caused by the removal of the ore. Cut-and-fill mining has evolved to use hydraulically placed tailings for the backfill. In the stope, this fill provides massive support to the walls, thereby reducing stresses in the back. It also provides a floor from which men and machines can work to drill and blast, to haul ore, and to scale and bolt the back. In many cases, the addition of cement provides a competent free-standing wall when the fill is exposed during mining of adjacent stopes or during pillar recovery operations. In most cases, the use of fill does not eliminate standard tem¬porary or local roof control measures such as roof bolts and wire mesh. Fill Characteristics It is important that backfill used for ground support be of maximum stiffness in relation to wall closure. The stiffness of the fill is related to its placement bulk density or void ratio. In the case of cemented tailings, this is enhanced by the cement bonds. During stope closure, individual fill particles experience rotation and crushing at point contacts, but they are subject to little relative translation. The stiffness approaches infinity as the void ratio approaches zero, until the ground forces reach equilibrium, and closure stops. The gradation of particle sizes and minimal segregation resulting from good hy¬draulic placement both contribute to a high degree of early stiffness in the closure history of classified tailings backfill. This also implies that the fill should be resistant to creeping under high static loads. All mines experience shock loading situations such as blasting, and many mines experience rock bursts that can apply sudden and very high loads to the fill. Certain conditions of void ratio, particle size, and moisture con¬tent can result in mass fluidization of unconsolidated fill during such shock loading. Two key factors in avoid¬ing fluid behavior are the provision of a well-drained fill through desliming or classification and the achievement of a small degree of consolidation through the addition of cement in ratios as lean as 40 to 1 (2.4% cement). The acceptance of classified mill tailings as backfill material has been enhanced by its relative economy, including its source, preparation, delivery, and stope distribution. Transportation from the backfill prepara¬tion plant on the surface into the stope usually can be accomplished with low power consumption, with low labor costs, with few capital costs, and at high tonnage rates. An additional benefit is a reduction of the storage volume required for surface disposal of the tailings stream, with a resultant improvement in the environ¬ment. The costs of placing cemented tailings backfill generally range from $1.65 to $6.61/t ($1.50 to $6.00 per st) of fill depending upon the cement ratio used. Scope This chapter examines a major backfill program at a mine and mill complex where the backfill facilities are included as a part of the original planning. The backfill preparation plant is intended to make maximum use of remote controls and automation. The logistics asso¬ciated with material storage, handling, and metering in the plant are outlined. Important considerations in specifying equipment for typical service conditions are discussed. The fill delivery system is described, includ¬ing the boreholes, level lines, and stope distribution lines. Stope preparations for fill confinement and drain¬age are described, as are the techniques of placement and distribution. Methods of controlling and directing the flow of drainage water and slimes are presented, along with the facilities and equipment for clarification, pumping, and sludge removal. As shown in Fig. 1, the fill program encompasses most aspects of the mining and refining facilities, so the discussion is brief in each area. The preparation of backfill of a uniform and con¬trollable quality is presented here as a material handling problem. The balance of the presentation concentrates on the logic of the system, the costs where meaningful (in 1977 US $ unless otherwise specified), and some operating "tricks" that have contributed to system per¬formance and reliability. SURFACE PREPARATION PLANT A backfill preparation plant is required on the surface. This plant generates suitable fill material from the stream of mill tailings. Among the functions of the plant are: 1) Slimes are removed to improve the percolation characteristics of the fill; typically, particles finer than 325 mesh are removed from the tailings. 2) Tailings and sand storages are provided so that the steady stream of tailings produced by the mill can be accepted. Provision is made to accommodate the cyclic high-volume demand from the mine. 3) The plant stores the cement and contains meter¬ing and mixing facilities to provide fill of a controllable and uniform quality. 4) The hydraulic backfill delivery system is a part

Jan 1, 1982

By P. Saunier, S. Fourmont, R. Stafford, A. Jung, J. Mlynarek

The safe and economical storage of tailings generated by modern day mining operations is possibly the single largest challenge faced by miners today. By nature, tailings are a waste product that have little to no economic value. Yet, their physical and chemical contents can pose incredible environmental hazards if not stored correctly. The variety of factors that are met when designing Tailing Storage Facilities (TSFs), means that in most cases, a low-cost solution is sought to accomplish storage, meet environmental regulations, and adhere to industry best practices. TSFs can be large dam face structures or smaller structures like retention/evaporation lined ponds. Water management is potentially the single largest factor that miners and designers must contend with when constructing a TSF. Water is a necessary component in the process of extracting ore but can be difficult and expensive to remove once it is mixed with solid tailings particles. As a result, the most common disposal of these water containing tailings, called a slurry, is to simply discharge into an embanked TSF (Vick, 1990). These structures, just like any other water retaining dam, can breach releasing contents downstream. Despite modern advancements in TSF design, there have been numerous dam failures that have resulted in tragic loss of life and ecological devastation. Most notably in the last decade, the Brumadinho and Mariana Dam disasters in Brazil killed 278 people in downstream communities when TSF dams failed in 2019 and 2015, respectively (Rotta at el., 2020). Similarly, in 2014, the Mount Polley tailings spill in British Columbia was the second largest tailings spill on record and caused extensive damage to adjacent watershed ecosystems when the TSF embankment was breached (Byrne at el., 2018). While there were indeed numerous unique and underlying factors present in each of these structural failures, a shared element in the devastation was the large-scale release of unstable liquefied tailings

Mar 2, 2022

By Bruce F. Bohor

Silica sand has been mined in Illinois from the St. Peter Sandstone since the turn of the century, especially in the area around Ottawa on the Illinois River in the north-central part of the state. Production of this sand, consumed mainly by the glass and foundry industries but also sought after for many other uses, has grown with the economy, and last year's output in Illinois exceeded 4,000,000 tons. Such an important commodity was given the early attention of the Illinois State Geological Survey, and a very complete report was issued in 1928, authored by J. E. Lamar. The mining and processing of the sand has changed very little during the intervening 40 years, so that much of Lamar's data and descriptions are applicable today. More recently, the stratigraphy of the St. Peter Sandstone in north-central Illinois has become better known from the work of Willman and Payne (1942). The present authors have borrowed generously from Lamar's publication, and we wish to acknowledge the contribution of both of these studies to our work.

Jan 1, 1969

By J. B. Rubinstein, V. J. Badenicov, S. T. Hall

A simulation technique of the flotation process and models for the solution of various problems are developed. A modular model of column flotation is constructed taking into account the kinetic relationship of the process and the hydrodynamic regime in the cell. Based on this, a technique of calculating the column parameters based on laboratory tests is developed (scaling-up), and applied for calcetest results is developed (scaling-up), and applied for calculating the design of commercial-scale columns.

Jan 1, 1996

By Bruno A. Fichna

Longwall mining offers low cost potential for coal with high capital investment. As opposed to two shifts-per-day operation in most long- walls, Saarberg Mines in Germany increase utilization of capital by operating their longwalls around the clock. Differentiation between capital and operating costs, corrective maintenance versus preventive maintenance, improved roof conditions, and economical life of equipment was investigated. A surprisingly high degree of improvement was attained. Capital costs at Saarberg longwall coal mines have been reduced through a step-by-step research and trial program. This reduction was particularly influenced by the high performance pilot longwalls at the Ensdorf mine. The following presentation shows data and figures of those longwalls. End results were 40% reduction in capital costs, which could contribute favorably to investment decisions in the coal industry in a supply side economics environment.

Jan 1, 1982

By R. L. Grayson, L. L. Probert

A three-year project focusing on the depth profiling of respirable coal mine dust particles using scanning electron microscopy coupled with energy dispersive X-ray analysis resulted in the development of statistically classified particle-behavior models. The models depict the changing silicon fraction for particles at 5-, 7-, 9-, and 11-keV accelerating voltages, thereby giving a clear indication of the nature of various types of mineral particles. This paper focuses on the results for respirable quartz particles sampled from five underground coal mines across the US. Through statistical analysis of results the relationship between the fraction of surface available quartz in respirable dust samples and coal rank is established for three Pennsylvania coal seams.

Jan 1, 1995

By W. Dalmijn, H. de Ruiter

"The decline in students for mining and metallurgical engineering in the last few years has lead to the closure of many university departments in all first world countries around the world. Three independent studies carried out in Europe, Australia and North America indicate that during the next decade the demand for mining, minerals processing and metallurgical engineers will be significantly higher than the supply. Demand for engineers will increase even more because many of the professionals in industry are about to retire within the next 5 years. Meanwhile mining is a growth industry, minerals demand continues to increase in line with the growth in World GDP, as illustrated in the Graph at the end of the paper."

Jan 1, 2005

By Raphael Mourad, Colin R. Phillips

Investigation of the traps in LiF:Mg, a multi-peak phosphor, was carried out using simple phosphorescence decay analysis. Half lives at room temperature of the trapping centres (peaks -lb, -la, -1, 0, 1, 2, 3a and 3) in the phosphor after irradiation with [a] radiation were found to be 3 s, 5 s, 28 s, 4 min, 15 min, 1 h, 6 h and 2 d respectively. Justification for the method of analysis is pro- vided and the results of measurements compared with published data. The effects of pre-annealing at 400°C for 1 h and 80°C for 24 h on the trapping configuration and on the trapping efficiencies were also studied.

Jan 1, 1981

By Barry K. Johnston, Norman W. Bainbridge, Neville C. Lockhart

CSIRO and its collaborators have developed a major R & D project on dewatering of coal. This involves sub-projects on (i) the fundamentals of coal-water associations; (ii) reducing the variability of product moisture levels from small coal centrifuges; (iii) process mechanisms and optimisation for fine coal dewatering; (iv) pilot scale testing, engineering development and innovation. Results from each of these sub-projects are presented, and the pilot facility incorporating a vacuum filter, belt press, membrane press, hyperbaric filters and centrifuges, is discussed. The vacuum filter and membrane press can be configured for electric-field assisted dewatering, which provides substantial enhancements in the rate and degree of dewatering for fine coal, coal tailings, and other suspensions.

Jan 1, 1995

By M. J. Laurila

Utilizing data compiled from a drilling program and bulk samples taken from a coal reserve, flowsheet performance for a coal preparation plant can be calculated using a desktop computer. Sets of equations defining material balances involving coal preparation plant unit operations are employed to depict plant performance. Techniques are discussed for interpolating washability data and extrapolating size distributions and other critical data to expand on oftentimes limited sets of quality data to a useable data base from which projections can be made. Simulation of flowsheets can be done for a number of different conditions and configurations while still remaining in a limited working memory capacity of 32,000 bytes. Presented within this paper are several pertinent examples.

Jan 1, 1982