Search Documents

By Larry Diaz

A single stage ball mill-cyclone circuit was extensively tested for its reactions to step changes in three controllable variables: feed rate, water to cyclones, and water to the ball mill. A series of carefully designed tests are to be carried out in order to determine relationships between the various ball mill and cyclone parameters. Cyclone overflow particle size distribution is to be continuously monitored during the tests using an ultrasonic device. Other circuit variables that are to be measured and recorded are feed rate, ball mill mass flow, cyclone feed and overflow densities, cyclone feed sump level, water flows, etc. Once the circuit performance is defined, two types of grinding circuit control systems will be evaluated: (a) mass flow-based; (b) particle size- based. Results obtained by each approach in terms of feed rate and cyclone overflow size distributions are discussed. The high sensitivity of continuous particle size measurements to grinding circuit disturbances is emphasized.

Jan 1, 1971

By Bryan A. Bartley

High intensity, autogenous grinding has been developed in the hard rock, quarry industry and is finding wide application in mineral processing. The autogenous vertical shaft impactor is described and action within the machine is illustrated. This machine is compared with the cascade mill, in the three characteristics of impact, inter-particle rubbing and nipping, of which impact is the most important. There is a seven fold increase in impact level over that of the cascade mill. The autogenous impactor has characteristics of crushing and grinding, preferential crushing, abrasion resistance and drying. These are illustrated by examples of industrial applications, where the machine is now used and range from abrasives, such as Carborundum to phosphate rock.

Jan 1, 1998

By A. Ligorio Pires de Carvalho

The main potash deposit at Taquari-Vassouras is contained in cycle VII, and consists of several sylvinite bodies. Cycle VII belongs to a sequence of nine cycles defined by Szatmari (1974) in the Sergipe-Alagoas basin. The sylvinite layers are separated by halite beds. They are seated on or may be laterally in discordant contact with other lithologies such as the tachyhydrites at the base, and the limestone breccia at the top. The main structural features in the deposit include numerous synclines and anticlines, salt dissolution phenomena, and open fractures associated with the axes of the anticlines.

Jan 1, 1995

By J. D. Morgan

Introduction In 1987, the US economy continued to grow steadily, reaching an annual rate of $4.6 trillion in the last quarter. The value of domestically processed mineralbased materials rose slightly to $250 billion. The value of US metals rose sharply to more than $7 billion. Industrial minerals rose slightly to $18 billion recycled scrap was valued at $4 billion. Metal prices rose sharply toward year-end. A number of mining and metal companies experienced increased profitability, fostering more optimism about the future. Consumer demand strongly affects mining because the US economy is relatively saturated with long-lived products. Consumer, mortgage, and federal debt continue to rise. 244 million citizens already possess 170 million licensed motor vehicles and 100 million dwelling units. New car production fell 9% to 7.1 million units, but truck and bus production rose 9% to 3.8 million units. New housing starts fell 10% to 1.6 million units. Excess productive capacity exists not only in the US, but also in many other countries. Consequently, the US mineral industry is encountering stiff competition from others, as well as increasing competition from newer engi¬neered materials. Domestic production of plastics rose 9% to 25 Mt (27 million st) - on a volume basis, double all metals. Some 7% of petroleum goes to make petrochemicals including plastics. Imports of nonfuel mineral-based materials in 1987 were valued at $37 billion and exports at $24 billion. Imports supplied a significant proportion of total US consumption of several important mineral materials, including many classified as strategic and critical. In December, the Congress mandated that any major changes in stockpile goals be made only by law, and that the Department of Defense submit annually detailed stockpile supply/demand analyses. Concern about apartheid in South Africa continued, resulting in increasing interest about chromium, manganese, platinum-group metals, cobalt, vanadium, and gold. The National Critical Materials Council continued to monitor the US materials position. The Defense Production Act, authorizing priorities and allocations, supply expansions, voluntary agreements, and the National Defense Executive Reserve continues in effect through Sept. 30, 1989. Under the DPA, the US Bureau of Mines maintains the Emergency Minerals Administration. Further consultations were held with Canada to strengthen the North American defense industrial base. Coal production, 60% from open pits, rose 2% to 825 Mt (910 million st) valued at $21 billion. Nearly four-fifths was burned to generate 56% of US electricity. Exports included 42 Mt (51 million st) of metallurgical coal and 24 Mt (27 million st) of steam coal, with a total value of $3.3 billion. Domestic petroleum production fell 5% to 480 Mm' (3 billion bbl). Uranium mining, including recovery from phosphates, fell 4% to 5.9 kt (6500 st). Nonfuel minerals Major metals: Raw steel production - a major consumer of many minerals - rose 7% to 79 Mt (87 million st). Domestic iron ore production rose 11% to 44 Mt (48 million st), about 96% pelletized. Net imports, though, fell 8% to 11 Mt (10 million st). Raw steelmaking capacity fell 6% to 102 Mt (112 mil-

Jan 5, 1988

By M. Plesha, A. Zubelewicz, K. Connor, T. B. Belytschko, O&apos

INTRODUCTION The Northwestern University Rigid Block Model (NURBM) has been extended to explicitly model dilatant behavior of rock joints. By incorporating dilatancy, the resistance to shear displacement and slip, which previously was limited to simple Coulomb friction, along edge-to- edge contacts is now provided by contact roughness as well as frictional resistance. The explicit formulation is based on concepts presented by Plesha (1985) in which a plasticity-based phenomenological approach was used to model dilatant joint behavior. This approach has been modified to allow for joint closure upon reversal of shear deformation. After presenting a brief description of the new joint constitutive relationship, model behavior will be illustrated with two examples. The first involves a simple two-block model to simulate a cyclic direct shear test of a single joint. The second example involves simulation of a large cavern in a moderately jointed rock mass subjected to cyclic excitation. It will be shown that in- creasing joint roughness increases cavern stability by interlocking of adjacent blocks. JOINT CONSTITUTIVE RELATIONSHIP Within NURBM adjacent two-dimensional rigid blocks interact along their common edge-to-edge contact with contact forces transmitted at the contact midpoint. The contact constitutive relationship was originally restricted to a Coulomb friction yield criterion with no tensile stresses permitted along the smooth contact surfaces. The local coordinate system for any contact is described as shown in Figure 1 with the elastic stresses and displacements related by the linear- elastic constitutive law: [ ] The contact microstructure has been modeled as Patton-type saw-tooth surfaces such as shown in Figure 2. Sliding can be active along the right asperity with angle aR and length lR or along the left asperity with angle a and length lL. In general, aR and aL will difkr as will lR and lL but for purposes of this paper it has been assumed that these angles and lengths are identical. By a simple transformation, the microscopic asperity stresses can be expressed in terms of the macroscopic contact stresses [ ] If Coulomb friction is assumed along the asperity surfaces, the plastic slip condition will be [ ] where µ is the friction coefficient with the convention that compressive stress is negative. When F is negative, the behavior is elastic and when F is zero, slip can ensure. When plastic slipping does occur, it is assumed that the relative tangential and normal displacements between the two contacting rigid blocks are additively composed of recoverable elastic parts and nonrecoverale plastic parts, [ ]

Jan 1, 1986

By L. Runqing, H. Yuehua, S. Lei, S. Wei

"Tin ore from the southeast of Yunnan in China is a complex polymetallic low-grade ore. Because of the highly disseminated extent ore, cassiterite flotation was applied in industrial production instead of the low efficient gravitational separation. Benzohydroxamic acid (BHA) was widely used as a collector in cassiterite flotation, but the consumption of BHA was large. In this study, the influence of octanol in cassiterite flotation from the southeast of Yunnan using BHA as the collector was investigated. The results indicated that single octanol showed almost no flotation capability to cassiterite without BHA. However a small amount addition of octanol as the auxiliary collector can decrease the consumption of BHA significantly, while did not reduced the recovery of cassiterite obviously. Infrared spectra analysis indicated that the single octanol adsorbed on the surface of cassiterite was unsteady adsorption, and a new entity assembled of BHA and octanol in a well manner was able to adsorb on the surface of cassiterite steadily. The probable self-assembly structure model of BHA and octanol existing on the surface of cassiterite was analyzed. INTRODUCTION Cassiterite is the prime and economic mineral from which tin metal is extracted economically (Qin et al., 2011). The estimated tin metal resources in the world is about 4.9 million tonnes, about 30.5% of which is distributed in China (Mineral commodity summaries, 2013). Cassiterite has many characteristics such as including heavy, hard, and extremely brittle in nature. Hence cassiterite is preferentially concentrated by gravity separators. However, the influence of particle size on gravity concentration is obviously. The separation efficiency is very high for coarse particles while it drops down considerably for fine sizes. (Turner and Hallewell, 1993). Application of flotation and development of selective surfactants have made it possible to recover fine and ultrafine cassiterite from the gravity tailings. A substantial amount of research work on cassiterite flotation has been reported in the past years. The outcome of such research has helped to develop various collector reagents such as cupferron (Vivian, 1927), sodium dodecyl sulfate (Edwards and Ewers, 1951), sodium oleate (Collins et al., 1968), salicyaldehyde (Marabini, 1978), alkyl and aryl arsonic acids (Senior and Poling, 1986), alkyl and aryl phosphonic acids (Gruner and Bilsing, 1992), alkyl sulfosuccinamates (Khangaonkar and Kamarudin, 1994), and alkyl hydroxamates (Sreenivas and Padmanabhan, 2002)."

Jan 1, 2016

The design of solvent extraction plants has been generally based on the assumption of steady operating conditions in both the settler and the mixer units. However, recent experience in both large and small plants has shown this not to be the case. Mixer transients include start up aqueous locking and partial phase separation in secondary mixers, which both lead to reduced plant capacity or overflow of upstream mixers. Analysis of the hydraulic pressure profiles has generated new design methods to eliminate the effects of the partial or complete phase separation. Changes to the method of specification and selection of primary and secondary mixers have been made to eliminate the onset of partial separation during operation. The observation of settler operation has shown that it is also a dynamic process, even under "steady-state" conditions. Four transient phenomena have been identified that lead to internal circulating flows, poor disengagement of fine secondary haze and erratic and high entrainment levels in the discharges. A, first approximation analysis has shown that there are significant pressure differentials within settlers, and these change along the length and with the phase separation rates. A technique to control the effects of these transients was developed that allows plant performance to be improved beyond "standard" expectations. The design and selection of the settler internals is described. Key words: Solvent extraction, Mixer-settlers, Phase separation, Entrainment, Mixer transients

Jan 1, 2003

By L. Arbore

Introduction Mine operators are interested in energy conversation in two ways. With our finite sources of energy, we are concerned for future generations. In addition, as mine operators, we want to minimize energy costs. Moving material represents a substantial amount of the energy used in mining operations. Wheeled vehicles are used extensively to move materials. And they derive all their energy from fuel. Energy is also required to overcome the vehicle's inertia, and internal and external frictional forces. Included in the vehicle's frictional forces is its suspension. Tires are an important part of this suspension. What influence do tires have on the overall fuel consumption of the vehicle? Does tire construction affect this influence? As far back as 1896, it was apparent that tires were a factor in fuel consumption. A test was devised in France using a coal-fueled steam-driven auto. The test measured whether there was any fuel savings with the new pneumatic tires rather than of the then commonly used solid tires. The result was a 28% savings in water and a 29% savings in coal on pneumatic tires. Today, the pneumatic tire is accepted, but there are differences in present constructions. Tire Construction: Bias vs Radial There are basically two types of tire construction, bias and radial. Bias tires have been around for about 60 years. Radial tires are more recent. They were developed to improve a tire's ability to withstand higher speeds and loads, as well as to improve tire life and vehicle handling. Another advantage of the radial tire is its lower rolling resistance. This characteristic results in lower fuel use by a vehicle. This has been demonstrated with passenger cars and over-the-road trucks. It is now being demonstrated with earthmoving equipment. A basic description of both types of tire construction should now be reviewed: The casing of a bias-ply tire is made up of crisscrossed textile plies or layers. The cords of these plies run on a bias, from bead to bead. The cords of each ply run on an angle relative to the cords of the adjacent plies. As the tire rolls and deflects, the angle between the cords changes, like the blades on scissors (Fig. 1). The cords of one ply pull one way, and the adjacent ply pulls another, straining each other. This movement generates heat. Since the same layers of cords wrap around under the tread, they

Jan 9, 1984

By H. Knorre, A. Griffiths, J. Loroesch

Introduction Hydrogen peroxide is known to the mining industry as a powerful oxidant, able to attack and to destroy cyanide, the most important leaching reagent (Knorre and Griffiths, 1984; Griffiths, 1988; Griffiths, 1988). CN- + H202 => OCN- + H2O The most recent development, however, is the use of H202 as an oxidant in the cyanidation of precious metals. This application may appear to be a contradiction to the above mentioned detoxification process. This can, indeed, be the case if certain conditions are not considered carefully. Degussa has developed a new process to enable the application of H2O2, in this field without having any detrimental effect on the cyanide. The incentive to seek an oxygen supplier like H2O2 instead of air was the fact that one of the most important conditions for the fast dissolution of gold is the presence of physically dissolved oxygen in the pulp (Kydryk and Kellog, 1954; Warstell, 1987). 2 Au + 4CN- + 1 /2 O2 + H2O => 2 [Au(CN)2]- + 2 OH Complete gold recovery within a reasonable leaching time may only be achieved if the pulp is saturated with dissolved oxygen. Gold losses in leach operations mainly occur due to the following reasons: • In some cases, the saturation of oxygen in the pulp cannot be achieved by aeration due to the difficulty to transfer oxygen from the gaseous into the liquid phase. This happens, for example, in pulps with a high viscosity. In such cases, even violent aeration only results in a low concentration of dissolved oxygen in the pulp. • In any case, the starting phase of leaching requires the highest amount of oxygen. Therefore, it is especially important to raise the dissolved oxygen level to saturation in the starting phase. Peroxide assisted leach process (PAL) The intention of the process is to introduce oxygen in a liquid form. As a result of intensive research work, it could be shown that hydrogen peroxide can be used as a source of oxygen in the leaching of gold ores. To avoid side reactions, the following conditions must be applied: • Hydrogen peroxide must be diluted before it is added to the pulp. • The dosage of H2O2, must be properly regulated based on the oxygen level of the pulp. • An important part of the continuous 02-control is a special oxygen electrode, which resists the extremely abrasive action of the pulp.

Jan 1, 1989

By M. Dean Kleinkopf, John Callahan, William M. Shepard, R. N. Schnepfe

Despite lower prices and the uncertain future of nuclear power, uranium continued to be the big attraction in 1979 exploration activity. Uranium again dominated exploration programs across the US-not only in primary producing states such as New Mexico and Wyoming, but in potential producing areas from the northern counties of Minnesota to the Grandfather Mountain region of North Carolina. The moratorium on uranium leasing was lifted in Colorado and Montana, and exploration activity intensified accordingly. In Wyoming, what may be the biggest uranium deposit in the state was discovered by Anaconda Copper Co. near Jeffrey City, but in general, there were few major discoveries and activity was concentrated on existing exploration programs. The Department of Energy expects 1979 uranium exploration expenditures to total $339 million, compared to the $314 million spent by industry in 1978. Surface exploration and development drilling in 1979 is estimated at 16.1 Mm, up slightly from 1978 figures. Gold demanded its share of the spotlight in 1979. Soaring prices lured prospectors, investors, operators, and speculators to Alaska, California, Colorado, and Washington in a small-scale gold fever. Exploration for molybdenum remained strong in Alaska, Colorado, and Washington, where mineralization at the Mt. Tolman prospect is now estimated at 816 Mt averaging 0.09% copper and 0.10% molybdenum disulfide. Again this year, one of the major deterrents to exploration was the drive to set aside huge areas of land as wilderness preserves. In Alaska, where Interior Secretary Cecil Andrus has withdrawn millions of acres under the Antiquities Act, BP Alaska decided to close its Anchorage office, reportedly due to the lack of public lands available for mineral exploration. In both geophysical and geochemical activity, the year is best characterized as one of consolidation and development of previous advances in the state of the art, without any fundamental breakthroughs. Many companies were active in the development of instrumentation. Continuing interest in spectral IP resulted in the introduction of two instruments, one by Phoenix Geophysics, the other to be announced shortly by Geotronics Corp. Radiometric and borehole logging equipment received considerable emphasis, reflecting the continued interest in uranium exploration. MINING ENGINEERING'S review of 1979 exploration activity, including state-by-state highlights and a review of geophysical and geochemical activity, begins on the following page.

Jan 5, 1980

By Lorraine B. Yde

Successful implementation of computer systems deals with meeting final systems objectives and cost and schedule requirements, but the final success is dependent upon personal inter- action. This is a case history of the installation of responsibility reporting at The Anaconda Co.'s Twin Buttes operation, later to become Anamax. The study has been documented as it occurred in hopes that it will illuminate the "people" side of computer systems implementation. Systems implementation involves negotiating with people. "The cooperative approach to negotiation (Nierenberg, 1968) the approach which vostulates that all varties must come away having gained something is based on a simple but important premise. Negotiation takes place between human beings. You cannot negotiate with a computer." This is a look at the human side of a major system installation. An attempt is made to show how a reporting system enabled a company to take a new look at itself. It is also an example of statements made by Toffler (1970) in Future Shock. "As machines take over routine tasks and the accelerative thrust increases the amount of novelty in the environment, more and more of the energy of society (and its organizations) must turn toward the solution of non-routine problems. This requires a degree of imagination and creativity that bureaucracy, with its man-in-a-slot organization, its permanent structures, and its hierarchies, is not well-equipped to provide."

Jan 1, 1979

By J. B. Pautler, A. E. Gross, M. G. Strominger

The U.S. Bureau of Mines research on the use of cement as an agglomeration aid allowed precious metals heap leaching to become an economically viable method of precious metal recovery during the 1980's. However, many agglomerated ore bodies still exhibited poor heap/agglomerate strength. Precious metal recovery was often too slow or required prohibitively high levels of cement to be economically sound. Problems with heap ponding, blinding, and solution channeling and "wash-out" indicated that there was a need within the industry to improve on existing agglomeration technology. An in-depth research effort was undertaken to satisfy this need. Three years of research led to a patent on the use of vinyl addition polymers as effective agglomeration aids. A close working relationship between Brewer Gold and Nalco Chemical Company aided in the development of this program. This paper details the pilot test work, the full-scale evaluation at Brewer Gold Company, and conclusions.

Jan 1, 1990

By Gerald L. Dollinger

INTRODUCTION Today more tunnels are being bored by mechanical means in igneuus and metemorphic rocks (i.e. "hard" rocks) than ever before, and there is reason to believe that this trend will continue in the future. Because of this, there is an increasing demand fur stronger, more powerful machines and fur cutters that are capable of handling the high loads and abrasive rock conditions that often accompany hard rock tunneling. Tunnel boring machines ("TM's") built today, therefure, generally have higher thrust and torque capabilities than those built in the past, and they are equipped with the largest cutters and rings now available. The recent experience in hard rock tunneling has demunstrated that TBMs can be both efficient and ecunumical under such conditions, and that acceptable performance rates can be achieved in all but the hardest rock. In spite of this success, it is believed that improvements in buth the cost of boring and in performance rates can still be made through mudificatiuns in the existing kerf cutting system. Some impruvements in TBM performance under hard rock conditions, fur example, have already been made thruugh the development of constant section rings that maintain a constant edge width and, therefore, a constant level of performance as they wear. The recent experience in hard rock tunneling has also produced a wealth of new TBM performance data through the systematic study

Jan 1, 1983

By M. Misra, I. Anazia

The dispersion of oily collector has a significant effect on the flotation recovery of ultrafine coal. Generally, reagent dispersion is accomplished by mechanical mixing and/or ultrasonic agitation, followed by direct addition of dispersed collector into the flotation cell. Such dispersion and reagent addition techniques are invariably inadequate and nonselective. A new collector addition technique involving gas phase transport of atomized collector has shown improved results when compared to conventional reagent addition techniques. This technique involves atomization of the collector into the air stream. Under these circumstances, an aerosol is introduced into the flotation cell. Initially, the oil is dispersed within the air phase (continuous with respect to oil), and the air phase is dispersed within the pulp (continuous with respect to aerosol). In the flotation cell, the atomized oil droplets coalesce on the bubble's surface and create a de facto oil-encapsulated bubble. This approach provides excellent dispersion, increases selectivity, and, most significantly, increases the flotation rate of ultrafine coal. Atomization of collector/frother combinations yielded improved flotation recovery and maintained near uniform froth levels, which is a desirable feature in coal flotation. Microscopic examinations of the attachment of oil- coated bubbles at a coal surface were conducted by attachment time and contact angle measurements. Oil-coated bubbles attach at significantly faster rates and with a higher contact angle than oil-free bubbles.

Jan 1, 1988

By Eric W. Johnson

In the late 1950's a low-grade copper ore zone was outlined at the fifty-year-old McIntyre Porcupine Mine in Northern Ontario. Following this an independent copper circuit was installed in the existing gold mill. The nature of the operation decreed that capital expenditure be a minimum. To this end, in order to resolve the problem of storing and grinding two separate ores, it was decided to install a divider in the existing 4000 ton capacity fine ore storage bin and to replace ten conventional feeders with sixteen Mexican feeders. The article describes a successful application of the Mexican type feeder.

Jan 1, 1968

By S. Rideout

As Assistant Director for Program Support for the Office of Surface Mining Reclamation and Enforcement (OSM), a bureau of the U.S. Department of the Interior, I am responsible for the regulatory and abandoned mine land programs under the Surface Mining Control and Reclamation Act of 1977, which governs the environmental impacts of coal mining. My perspective is influenced by my current position and my previous positions in government and private industry. Sustainability is a cooperative effort of many parties and can only be achieved if each assumes their responsibilities for making it happen. I will highlight some of my thoughts on the role of government in achieving sustainability in the mining arena.

Jan 1, 2007

By James L. Evers

Introduction There is a continuing search by government and industry for new mining methods that increase production, improve the working environment, reduce labor intensity, enhance recovery effectiveness, improve the reclamation process, streamline the flow of material, and reduce the unit cost. Hydraulic extraction and transport methods have outstanding potential in several of these areas. For example, hydraulic fragmentation produces a significant reduction in respirable dust. The inherent simplicity of hydraulic mining equipment and the resulting high reliability are recognized. Tool wear can be virtually eliminated. There is great flexibility in the size, shape, and orientation of the mineral deposit that can be mined. The cutting, gathering, and transport operation can be controlled remotely, providing more safety for workers. The threat of tool sparking and the resuiting dust or gas ignition are also eliminated. Although hydraulic mining was introduced in the US before the turn of the century, it has not gained the degree of acceptance found in other countries such as the Soviet Union, China, Germany, and Canada. The Hydraulic Mining Research program, initiated by the US Bureau of Mines in 1958, and the subsequent research by others has provided much of the basic technology required to spur the development of these methods into a viable extraction alternative. This article updates the development of hydraulic mining in the US. Particular attention is paid to monitor mining, the long-wall hydrominer, borehole mining, and the semi-autonomous mining system. Whenever the particular mining method is also being developed in other parts of the world, a brief description of the world-wide state of the art is given. Finally, allied studies designed to optimize these mining techniques are described. Hydraulic Monitor Mining Since 1958, the US Bureau of Mines (USBM), the Department of Energy (DOE), and other government agencies have funded more than a dozen programs to investigate the potential of hydraulic monitor mining. For this method, water is directed on the coal face from a monitor nozzle. Sufficient velocity is used to cause local fragmentation (Fig. 1). Coal particles are washed from the face to a trough. They are then flumed to a collection point. Oversized particles are directed through a breaker and then into the troughs. Monitor field tests were conducted in the 1960s in bituminous and anthracite coal at the following locations: • Rosylin No. 9 mine, WA (Nasiatka and Badda, 1963); • Rosylin No. 10 mine, WA (Price and Badda, 1965); • Sugar Notch mine, PA (Buch, 1964); • Thomson Creek mine, CO (Palowitch and Malinka, 1964); and • West Lebanon, PA (Fowkes and Wallace, 1968). In 1975, Ingersoll-Rand Research Inc. was awarded a two-year USBM contract to develop a continuous coal mining system using water jet fragmentation and

Jan 10, 1984

By M. L. Maniocha

Most magnesia, MgO, whether of natural or synthetic origin, is utilized in its dead burned or periclase form as refractory linings for the production of steel. Continued research in refractory science combined with good refractory maintenance and improvements in steel making practice have resulted in decreased use of magnesia. To make up for this loss of business producers of synthetic magnesia have started to manufacture a variety of magnesium based chemicals that are utilized in many diverse industries and applications.

Jan 1, 1997

By G. E. Jones, G. K. Hoffman

Two Sun Juan Basin studies were completed through the USGS National Coal Availability program. The study areas are in the northwest Bisti field (Fruitland Formation) and in the eastern Standing Rock field (Menefee Formation). In the Bisti and Standing Rock areas, the original coal resource5 are estimated at 4.66 and 3.1 7 Gt (5.14 and 3.49 billion st), respectively. The Bisti coal resources are greatly reduced by the Bisti-De-Nu- Zin wilderness area, which contains an estimated 1.13 Gt (1.25 billion st) of coal. Technological restrictions remove 32.5% from Standing Rock's original resource. Available resources are 60%. 2.79 Gt (3.07 billion st), of the Bisti original resource and 65%, 2.07 Gt (2.28 billion st), of the original Standing Rock resource.

Jan 1, 2002

By V. R. Bovino

You have afforded me the challenge of saying something profound in 20 minutes that will stay with you for 20 years. My hope is that from this presentation you will extract ideas that will move you? out of your offices, into the mine to seize upon the concepts that we will discuss. Your challenge is to transform those concepts into action and give life to the ideas discussed here. The notion of achieving limitless productivity produces peak levels of enthusiasm in today's mining leaders. Highly-productive mines do not happen by chance --they are created by progressive leaders. The quest for productivity improvement, exclusively through capital investment and technological advances, is an incomplete process. Improvement, through capital and technology, is often not achieved because we fail to energize the true potential and commitment in our employees.

Jan 1, 1991