Search Documents

By Allison L. Hornbaker

Millions of years ago, in late Cretaceous time before man existed on Earth, tremendous orogenic forces began to change the face of the western part of the North American Continent. Catastrophic events marked by huge uplifts of thousands of square miles in the Cordilleran Belt, some of which are barely discernible in the geologic record, were accompanied by long periods of batholithic intrusions and volcanic eruptions. These events produced the great Rocky Mountain systems, which were at the time even higher and more rugged than they are today. Such activity continued into Tertiary time, and during the Pliocene and Pleistocene periods millions of tons of volcanic ash were hurled skyward by explosive volcanic activity and carried by the westerly winds to the east where it settled out of the atmosphere and deposited over thousands of square miles of the high plains. Unusually heavy rains, probably caused in part by the volcanic activity itself, together with high winds, reworked and redeposited the freshly fallen ash into lakes and depressions of varying sizes and shapes. Subsequent deposits of sand, gravel and loess covered the deposits of volcanic ash, preserving them in the condition in which they are found today. In many places erosion has cut through the sand, gravel, loess, and volcanic ash so that in favorable localities on hillsides and gullies, exposures of volcanic ash can be seen interbedded with sand and gravel.

Jan 1, 1970

Thermal pretreatment can significantly improve industrial comminution operations by reducing energy requirements and increasing mineral liberation. The effect of pretreatment using conventional and dielectric heating followed by quenching on the fracture properties of a number single and multiphase brittle materials has been investigated. The reduction in the impact fracture energies and particle strengths with and without pretreatment has been measured in precise single-particle experiments using the Ultrafast Load Cell. Variations in the fragmentation pattern caused by different pretreatments were assessed by measurements of the progeny size distributions. The differences in the effect of thermal treatment on single and multiphase materials are discussed based on the experimental results.

Jan 1, 1995

By L. Barry Phelps

Selective placement of toxic mine spoil has been advocated as a means of reducing environmental pollution at the source. However, methods of burial to control environmental damage are not well understood. Using the finite element method, this paper investigates the burial of toxic material within low permeability packages below the water table. The effects of differing package and spoil permeabilities, anisotropy, and infiltration are modeled to provide information about their effect on the flow system. Projection can then be made which will assist in the design of the toxic spoil packages to limit the amount of groundwater flowing through them.

Jan 1, 1983

By Robert H. Merrill

INTRODUCTION In most cases, the design of an underground mine is based upon the premise that the ground either will cave or will be stable. This chapter concerns the design of a mine in ground that will cave readily or with some as¬sistance, such as by long-hole drilling and blasting. Some of the more widely used caving systems of mining are panel caving, block caving, sublevel caving, and large pillar recovery. Some of the less widely used systems are glory-hole, top slicing, and induction caving. Al¬though the common practice of pillar robbing is not usually considered to be a caving system, this subject will be treated as a part of this chapter. BASICS OF CAVING Caving systems are most successful in ground that will cave in sizes that will flow through openings and grizzlies, and will easily load in cars or on belts for haul¬age. The ground most likely to cave well is highly frac¬tured and contains breaks, flaws, or other discontinui¬ties that form planes of weakness. Also, caving action can be greatly enhanced if the host rock itself is low in compressive, shear, and tensile strength. Ideally, a cav¬ing system of mining is best employed when the criteria for caving is a feature of the ore body and the develop¬ment drifts, haulageways, and drawpoints can be mined in a highly competent rock beneath the mineralized zone. However, the development is often in the same, or similar, fractured rock and the openings require sub¬stantial artificial support to assure stability. Several clues can be assembled to identify potential caving ground; however, for borderline cases, no sure method has been devised to date. The diamond-drill cores taken for exploration can provide an excellent clue provided drilling is performed carefully by experienced drillers. For example, if the ground is cored in such a manner that the breaks in the core are caused more by failure of the rock than by whipping core barrels, plugged drill bits, or other drilling causes, and the intact core lengths are consistently long [say, 0.6 to 3 m (2 to 10 ft) of unbroken core], there is little reason to believe the ground will cave without considerable as¬sistance. This is especially true for rocks with compres¬sive strengths above 34.5 MPa (5000 psi) and tensile strengths above 2.1 MPa (300 psi). On the other hand, if core recovery is low (below 80%) and the recovered ore is broken in small pieces and the breaks are along obvious weaknesses in the rock, the chances are excel¬lent that the ground will cave. This is true even when the rock between the defects has high compressive and tensile strength. Another clue has already been mentioned, that is, the measurement of the physical properties of the rock and the natural planes of weakness or defects in the rock. The planes of weakness in the rock can often be detected from outcrops, cores, or other exposures of the rock under consideration. Some rock types are known to be strong and will sustain large, unsupported open¬ings and would be difficult to cave intentionally. Yet the same rock type can also contain unbonded or weak planes of weakness or fractures, and in these locations the rock would undoubtedly cave with little assistance. Therefore, although the inherent strength of the rock is a factor in caving, the natural defects in the rock are more often the deciding factor. DESIGN CONCEPTS For the most part, the design of openings for caving ground is a problem of the interaction of openings over a relatively large area of the mine. To illustrate, Fig. 1 is a simplified section of a series of openings along the grizzly level or draw level of a block caving or panel caving development, and above this opening is a simpli¬fied section of a room-and-pillar arrangement on the undercut level. At this stage of the development, the stresses around the openings on the grizzly level are only moderately influenced by the openings on the undercut level and vice versa. Therefore, the stresses around the openings are approximated by the stresses around single or multiple openings in rock, the values of which are de¬scribed in the literature (Obert, Duvall, and Merrill, 1960; Obert and Duvall, 1967). Once the pillars on the undercut level are blasted (Fig. 2), the situation changes abruptly. The undercut opening (prior to caving) now can be approximated as an ovaloidal opening above the grizzly drifts and this opening tends to shield the vertical stress field. As the caved stage is drawn the stope approximates a much larger rectangular or square opening filled with rock, and if the rock is not sustaining a major portion of the stress field, this opening can be considered (for en¬gineering purposes) to be empty and the stresses that interact between the larger and the smaller openings take on a totally new perspective (see Fig. 3). Next, let the material cave to the surface, and let the caving ma¬terial sustain some stress, but much less than if the ma¬terial were intact. This condition is similar to a soft inclusion in a rigid body and has been treated in the literature (for example, Donnell, 1941). At this point in time, the grizzly drifts are subjected to the stress con-

Jan 1, 1982

By Kenneth L. Clifford

We have heard a lot during the recession about the mining industry now competing in a world market for sales of such commodities as copper, lead, zinc, molybdenum, iron ore, and phosphate. If the US mining industry is to survive, do we not have to reduce direct operating costs to a minimum? How significant is labor cost compared to consumables, electricity, fuel, maintenance, materials, and transportation? Ore grade is ultimately the dominant factor; but can we offset its dominance by improving productivity? Is the US mining industry perhaps only 25-30% as productive as it might be? What prevents the industry from being more productive? Can we retrofit older plants to be more productive or does it take a new plant with the largest equipment available for each unit operation? Present Productivity A copper industry study a few years ago covering 13 US copper concentrators ranging from about 10-45 kt/d (11,000-50,000 stpd) showed that productivity did not vary with capacity above 18 kt/d (20,000 stpd). Operating productivity varied significantly, however, from about 180-635 t/d (200-700 stpd) per operating hourly worker in most units, but one operation had 900 kt/d (1,000 stpd). Concentrators with more than 545 t/d (600 stpd) per hourly worker were in the 23 kt/d (25,000 stpd) or more category. Maintenance productivity covered about the same range, but most concentrators were in the 270¬635 t/d (300-700 stpd) per hourly maintenance worker. Again, one company stood well above others by exceeding 1 kt/d (1,100 stpd). Total hourly productivity ranged from 125-280 t/d (140-310 stpd) per hourly worker for most concentrators. The company with the most productive operation, however, was above 455 t/d (500 stpd). Salaried worker productivity for most operations was in the 725 t/d to 1.2 kt/d (800-1,300 stpd) per salaried worker range. The best operation was 2.2 kt/d (2,400 stpd). The end result is, of course, tons per day per total personnel. Most operations fell in the 110-220 t/d (120-240 stpd) range with the best operation at 400 t/d (440 stpd). This is the productivity definition that is most directly related to unit costs. Many of these operations have made some productivity progress

Jan 11, 1983

By Y. Kurokawa, R. Kurosawa, I. Iwata, I. Fukuoka, N. Sugita

INTRODUCTION The Ningyo-toge Mine is located in the western part of Honshu, about 800 km from Tokyo. Since the discovery of uranium ore deposit at Ningyo-toge in 1955, different kinds of mining and milling tests have been carried out. A new pilot plant of milling and UF6 conversion is also being under construction. Operations are scheduled to start by the end of this year. In 1979, the uranium enrichment pilot plant was constructed at Ningyo-toge and test operations have started. Thus, the Ningyo-toge area is assigned to undertake the Research and Development of the upstream of the nuclear fuel cycle in Japan. PNC has been strengthening its security measures more than ever. This paper will focus on the disposal of wasted material, especially on the disposal of heap leaching residue, in Japan. URANIUM ORE DEPOSITS The uranium of the Ningyo-toge Mine is characterized genetically by epigenetic sedimentary type deposits. They occur in the host rock of Neogene tertiary fluviatile conglomerates and sandstones which unconformably overlies the Mesozoic-Palaeogene granitic basement covered with lucustrine deposits and volcanic ejecta. More than 12 deposits have been found over the area of approximately 160 km2, and distribution of the deposits are strongly controlled by the so-called channel structure, probably remnants of paleo-streams on the denudation surface of the underlying grantic basement. Each ore body has different shape and dimension respectively, but about 2-3 meters thickness with the average grade of 0.05-0.2% U308 is common feature of the ore bodies. The ore is soft and loose, and it is composed of common rock forming minerals of allogenic origin and their altered products. The chemical composition of the ore depends on the constituents of the country rocks or the pebbles. A primary mineral, ningyoite and secondary mineral, autunite are major ore minerals, although three primary tetravalent minerals and thirteen secondary hexavalent minerals have also been detected. MINING EXPERIMENT Since 1959, various types of underground mining tests have been carried out at Ningyo-toge Mine. The room and pillar method was safe and simple, although the uranium ore recovery was below 70%. After experiment of the retreating long-wall method and slicing mining method, it was found that the modified long wall method was the most appropriate for the underground mining of the Ningyo-toge uranium deposits. This method was completed successfully to increase efficiency up to 2 or 3 times, as compared to conventional methods. MILLING EXPERIMENT In 1964, a small test mill was constructed at Ningyo-toge, and a milling experiment using the Ningyo-toge uranium ore was started. Re-modelling of equipments and improvement of the process lead to the establishment of the technique of the so-called wet process, and produce UF4 directly from the ore. The flow diagram is shown in Fig. 1.

Jan 1, 1981

By L. T. Larson

Nothing in Turkey is simple. Its his¬tory is long and convoluted, its culture fascinating, its metallogeny diverse, and its geology very complex. This article will focus on the geology of western Anatolia and the precious metals poten¬tial of this third of Turkey. Any gold produced by mines in Tur¬key since the early 1900s has been a by-product of the mining for other met¬als, such as copper from the massive sulfide deposits of the Pontics. Archaeological records, however, prove that gold was mined from the Pactolus (present day Gediz) River and refined by Croesus at Sardis in about 550 BC. Other records and legends make it possible that gold was mined before 1200 BC for the Homeric City of Troy (Priams treasure?) about 25 km (15 miles) east of Canakkale at Mad¬endag and Kartaldag. A final legend of antiquity suggesting gold in what is now Turkey relates to King Midas. And, indeed, the city-state belonging to a king of that name has been recognized near the city of Eskise¬hir. More recently, precious metals have been mined at Madendag-Kartaldag in the late 1800s. Arapdag, near Izmir, remains the only "authenticated" epith¬ermal precious metal deposit in Turkey (Mosier et al., 1985). With this spotty record, why the sud¬den interest shown by at least five Euro¬pean-based, three or four US-based, and several other international mining firms and their Turkish subsidiaries? Like other aspects of Turkey, the complete answer is not simple but, reduced to its basics, has three parts. Turkey, relative to many developing nations, has a stable, democratic form of government (although it also has a for¬midable bureaucracy) whose currency exchange rate is premised on the US dollar. New laws promulgated since 1983 have opened the country and welcomed foreign investment. Some have even provided investment incentives. The Mining Law of August 1985 made sweeping reforms of the old land tenure system. This law made it possible for a foreign-based company to have a wholly-owned Turkish subsidiary en¬gaged in mining. Equally important is the belated recognition that western Anatolia, while geologically compli¬cated, is today basically a province Neogene extensional tectonics having many of the geologic attributes of the leading gold producing province of the US - the Basin and the Range. Geologic rationale for precious metals exploration Tectonic/lithologic framework: Alle¬gorically and simplistically, Anatolia during early Neogene (middle Miocene) can be likened to a tube of toothpaste with the cap off. It is squeezed in the vise formed by the Arabian plate mi¬grating north toward the southwest end of a stable Asian platform. The "tube" was compressed. It could not expand to the east because it was sealed by what is now southern Russia and Iran. The filling of the tube escaped to the west, in the direction in which the cap was miss¬ing (Fig. 1). So developed during the middle to late Miocene the western-most struc¬tural province of Anatolia. This was done by a process aptly termed tectonic "escape" by Sengor et al (1985). This province is dominated by exten¬sional tectonics much like the Basin and Range of the western US and has an estimated extension of between 30% and 50%. The most striking manifesta¬tion of this extension is the 10 to 11 major east-west trending grabens (Ge¬diz, Buyuk Mendares, Kocuk Mendares, etc.) and intervening horsts, although a much greater number of smaller, gener¬ally northeast-striking grabens and half

Jan 1, 1989

Hoses provide a variety of critical functions in nearly every mining operation. Care must be taken when selecting, installing, and maintaining hoses to insure maximum hose life. This article provides some tips on selecting, installing, and maintaining hoses, and gives some background on hose construction and safety. In the mining industry, hoses are used for everything from hydraulic systems that power drills and hammers, to suction systems that carry away dust and debris. Hoses are used on such a large scale that a detailed discussion of specific applications would require many volumes. Dayco Corp. has, however, provided these basic and brief guidelines on how to select and maintain hoses for mining applications. Hose Construction Industrial hoses are classified as much by construction as they are by application. So, it is a good idea to start any discussion of hoses with a description of their basic construction. There are four basic components to hoses: the tube, reinforcement, cover, and couplings. The tube is the inner core or lining, and is usually made of smooth rubber or plastic. Rubber or plastic composition is scientifically determined to be compatible with the materials passing through it, such as fluids, chemicals, gases, or substances. Other considerations in compounding rubber or plastic for the tube are temperature ranges and stresses. In practice, the required compound can be precisely chosen from various charts listing them according to application. There are, however, applications where the compounding of tube rubber or plastic must be customized. The reinforcement hose layer immediately surrounds the tube. As its name implies, this layer gives the hose strength and provides protection for the tube component. Reinforcement must be able to contain the inner forces-pressure and shock-transmitted through the tube, and such external forces as twisting, bending, and crushing. So it is usually made of high tensile strength cord, fabric, or wire that is wrapped, wound, or braided around the tube. The cover is the outermost layer, so it may encounter oils, acids, water, dust, abrasion, and other potentially damaging influences depending, of course, on the application. An appropriate cover material must be selected, usually a rubber compound. Couplings, even though they are a hose attachment, are as vital as any other component and should be considered part of the hose. Couplings are usually made of carbon steel or malleable iron; however, bronze or stainless steel might be used if corrosive chemicals are involved and brass or aluminum might be used for flammable fluids. A coupling is usually in two parts: an insert that fits into the hose bore and contains the threaded male, female, or other type of connection, and the ferrule or collar that fits over the hose and secures the coupling in place. There are, however, some one-part couplings that fit securely into the hose without a ferrule. These are usually limited to low pressure applications and are secured to the hose by clamps or metal bands. Some fittings can also be permanently "built-in" as the hose is made. Couplings can be classified as reusable or permanent. The reusables can be removed when the old hose expires and used again on a new hose. The permanent types are crimped or swaged on at the factory or in the field (using special equipment) and must be discarded with the hose. Although couplings are most commonly thought of as having threaded fittings, there is another type called "quick connect." These either have a crow-foot or jaw-type design that permits a fast, "snap" connection. This can

Jan 6, 1982

By J. G. Clevenger

Introduction Computer-based haul truck dispatching has been operational at Tyrone since May, 1980. The system, known as Dispatch, has accomplished significant productivity gains compared with the former method of manual radio dispatching. These gains translate into a reduction in equipment requirements or an increase in production. An operational mine may choose to increase production or reduce the number of equipment shifts operated, resulting in substantial operating savings. Dispatch Description The core of Dispatch is a VAX 11/780 computer. Originally purchased with 512 kbytes of memory, the system is now upgraded to 3.75 Mbytes to accommodate users from all areas of the operation. Dispatch alone requires 200 kbytes of locked-in memory, with an additional 300 kbytes of memory available on a top priority basis. The computer, located in the Tyrone Branch general office building, is connected by under-ground cables to the dispatch tower, 3.2 km (2 miles) from the general office. Four two-paired lines are used to drive two cathode ray tubes, a printer, and the Dispatch master panel. One CRT continuously displays pertinent pit information for the dispatcher's use. Routinely displayed transactions include truck assignments, changes in shovel material type, truck and shovel breakdowns and delays, and changes in truck, shovel, or dump status. Er¬ror detection capabilities include late arrival and improper input from the field panels. The second display terminal is used for utility reporting and input functions. Status reports are displayed for availability, position, and material type being handled by any given truck or shovel. Fuel reports are available indicating the time last fueled, quantity of fuel delivered, and the time spent fueling. A truck factor utility reports relative performance to other trucks and a shovel utility reports efficiencies in tons per shovel shift. Instantaneous shift reports and mine status reports are available. Inputs such as lineups, operator changes, new travel times, shovel bias, tie down times, and lunch times are all handled with the utility display terminal. The printer records a hard copy of operating truck locations and production from the beginning of each shift. If there is a system malfunction, the printer copy is readily available to the foreman for radio dispatching. The Dispatch master panel is a microprocessor-based panel that allows the dispatcher to override any computer-assigned transaction. Classification of "bad order" conditions and acceptance of certain field messages is entered through the master panel. This panel communicates with all truck and shovel field panels via UH radio frequency through a repeater tower located on a high ridge contiguous to the mining area. Each truck and shovel field panel unit transmits a coded signal that is identified by the computer. A typical communication sequence between field panels and the computer for one complete truck cycle is: • The truck panel LED display indicates the shovel number to which it is assigned. The truck arrives at its assigned shovel and the operator presses the "Arrive" button on the truck panel. As the computer receives the "Arrive" message, it concludes the return (empty) travel time and begins accumulating idle time before loading. • When the first dipper of muck is placed into the bed of the truck, the operator presses the "Load" button. The computer concludes the truck idle time accumulation and begins the loading time calculation. • When the truck is loaded, the shovel operator presses the "OK"

Jan 9, 1983

By Betty L. Gibbs, Jean A. Arcamone

Introduction Microcomputers are becoming more convenient to use at all levels in the business world, including the mining industry. The state of the mining industry requires that we become more productive and innovative in our analysis of deposits and operations. With the help of computers, examination of options to increase productivity can be performed quickly and inexpensively. Effective computer use to design underground workings combines the calculating power and speed of a computer with the technical expertise and judgment of an engineer. Computer programs can perform in minutes calculations that might take several months for an engineer. But the engineer must be on guard when using computers for calculations. It is easy to assume the results produced by a computer program are always correct. However, the computer is only a sophisticated calculator. It cannot recognize logical errors or transposition of numbers. Also, some intuitive or obvious decisions made by an engineer are difficult or impossible to program effectively. In this article, selected commercial programs are discussed. These programs can provide engineers with tools to evaluate engineering designs for underground mines. The programs perform much of the tedious calculation. The engineer, though, must still make decisions and conceptualize designs. The software mentioned in this article runs on microcomputers and minicomputers. The mention of particular software, however, does not imply endorsement. Mining projects After a decision has been made to proceed with an underground mining project, more detailed evaluation of the mining method and extraction sequence begins. If a mine is already in operation, schedules and plans are needed to more clearly define future production. Existing operations can benefit from identification of bottlenecks in material movement and produce extraction options to make the mine more efficient. Detailed studies for a new mine are based on the technical engineering design. These studies provide specific details to determine equipment requirements. Detailed studies done during a project are similar to short-term planning and control carried out daily by the mining engineers. The engineering design phase includes: • Study of the infrastructures - entries, shaft, access from surface to underground; • Definition of the mine layout, hydrogeology, geotechnical considerations, transport, and ventilation; • Choice of machines and equipment; • Mine scheduling, including waste extraction and production sequencing; and • Economics, including labor and supplies. Further detailed studies include: • Blasting patterns; • Detailed geotechnical calculations; • Secondary ventilation; and • Production cycles along with coordination of the workings. Objectives The primary objective of underground mine planning is moving material out of the mine at the least cost. Development of the production schedule considers location and volume of ore units, transport distance, equipment and manpower interactions, and grade or quality of material. Two methods can be used to determine the scheduled material removal: optimization or trial and error. The microcomputer programs discussed here do not cover optimization for underground mine planning. For several reasons, optimization is often a "black box" approach. Although optimization is possible with linear programming techniques, few mining operations can be described effectively with linear equations. An interactive trial-and-error approach is desirable because engineering judgment can be inserted as a plan develops. Because of the large number of factors in an underground operation, an optimization technique seldom covers all possibilities. Few of the programs available consider all of the possible parameters. The programs use an interactive sequencing or a simulation approach and are either event-oriented or deposit-oriented. The most desirable programs offer an integrated approach. They consider a broad range of operating conditions including equipment, labor, costs, material movement, timing, and mine layout, among other factors. The two types of models generally used in designing underground workings include: • The interactive model, which requires direct, incremental input from the user. Outlines of the section to be mined may show on the screen. The engineer causes the model to develop piece-by-piece. The program may offer feedback on parameters such as tons and grade, or other values, as the section is "mined." • The simulation model, which is usually an automatic technique. Parameters related to the process are entered. The program then calculates the mining sequence over a designated time period or until the economic material is exhausted. A simulation model imitates step-by-step performance of equipment or other processes.

Jan 3, 1988

By Robert F. Conley

In the mining, manufacturing and application of inorganic pigments, dispersion contributes significantly. This is especially true with mineral pigments because of the variety, in slurry operations required for their processing. Such operations include any of the following: (1) mine-transport (2) wet grinding (3) flotation/beneficiation (4) wet magnetic separation (5) selective floculation (6) size classification (7) chemical processing (8) spray drying Dosage levels and general economics of dispersant use are broadly variant, being dependant upon the agents employed, from the simplist, i.e., sodium silicate or sodium carbonate, to the more complex, as polyacrylates and organo-phosphates. In certain unit processes the dispersant must exhibit unusual chemical stability and persistence, e.g., in protracted pigment slurry shipments. In others, the agent should be fugitive to prevent secondary reactions from occurring, e.g., with high temperature calcination where alkali salts can act as aggregation fluxing agents.

Jan 1, 1985

By Robert L. Runkel, Kenneth E. Bencala, Briant A. Kimball, Katherine Walton-Day

The solute-transport model OTIS and the reactive solute-transport model OTEQ were used to simulate geochemical conditions in Cement Creek, a tributary to the Anirnas River in Colorado. OTIS was used to depict instream zinc concentrations, and to simulate the effects of two remediation scenarios on zinc concentrations at the mouth of Cement Creek. These simulations do not account for effects of changing stream pH on metal concentrations. Preliminary simulations using OTEQ to account for instream pH changes were unsuccessful due to the spatial nature of mixing processes, and insufficient information about the thermodynamic properties of precipitates forming in mixing zones.

Jan 1, 2000

By P. J. Lafforgue

In 1974- COGEMA (Compagnie Generale des Matieres Nucleaires) of France decided to exploit a uranium deposit discovered several years ago in a Permian formation of Southern France, near the town of Lodeve (Herault). The uranium occurs in black shales with high calcium carbonate content (7-10% CO2) and it was then necessary to use alkaline leaching. A fine grind (60-65% minue 270 mesh) was also necessary to obtain good' uranium recovery. A minimum of fresh water must be added to the alkaline system due to solution recycling. Filtration must be used because cake-washing requires less fresh water than countercurrent decantation.

Jan 1, 1982

By John A. Breslin

The U.S. Bureau of Mines develops technology to help ensure that the Nation has an adequate and dependable. supply of minerals at reasonable economic, human, and environmental cost. Our research programs seek improvements for almost every aspect of the mineral production cycle--from evaluating the availability of minerals, removing the ore from the earth, to enhancing the performance of mineral materials. The health and safety of the men and women who work in the Nation's mines and minerals processing plants and the environmental impact of mining and mineral processing are major Bureau research concerns. In recent years, the U.S. mineral industry has found it increasingly difficult to compete for a share of world markets. Many foreign producers benefit from lower production costs and higher grade deposits. Some foreign governments subsidize their mineral industries and impose fewer restrictions with respect to environmental controls and health and safety regulations. If the United States is to compete in world mineral markets, innovative technology must be found to lower the cost of recovering and processing minerals. Mining and mineral processing research by the Bureau identifies ways to help the country maintain a sound, competitive industry and a dependable mineral supply, so vital to economic growth and the national security. This work includes efforts to improve existing techniques and procedures; but more and more of the Bureau's resources are being focused on long-term, high-risk research directed at developing new approaches to mining and mineral activities--approaches like in situ mining. Bureau scientists are studying the mining applications of computer assisted mining and investigating a variety of "high tech" approaches to extractive metallurgy. Such cutting-edge research will be necessary if major advances in health and safety, environmental quality, strategic and critical minerals availability, and overall U.S. competitiveness are to be achieved. It is just such high-risk research that the industry cannot afford to conduct itself, but--in the long run--cannot afford to be without. It is this type of research that will help us arrive at a revolutionary breakthrough rather than small incremental changes in health and safety technology as well as recovery methods. Our mining and mineral processing research is also directed at reducing the Nation's dependence on imports of minerals that have key defense and industrial uses. Some of these strategic and critical minerals are particularly vulnerable to supply disruptions. We are working on technologies that would allow the United States to take advantage of domestic sources of these minerals--sources consisting primarily of deep or low-grade ores, ores with complex mineralogy we do not yet know how to process, and small deposits that are now uneconomical to mine and process. Other research activities focus on ways to reduce the Nation"s consumption of key minerals and increase the recycling of these minerals. The opportunities in this area include coal. The current middle eastern crisis reinforces the need for a stable energy supply--preferably a domestic supply. The extensive reserves of coal in this country are well documented. Perhaps what is not as well recognized is the impact that the price of coal can have on its competitive position both for domestic fuel selection considerations as well as for the ability of this country to compete in the coal export market. Today, the role to the United States is as a reliable, but high-cost exporter of high-quality coal. U.S. export coal competes with supplies from other major suppliers, including Australia, Canada, Poland. If U.S. mining costs were lowered by at least $8 per ton in the year 2000, then coal exports would surge by a projected 46 percent, and U.S steam coal displaces significant quantities of foreign coal imports in Europe. Further cost reductions would make

Jan 1, 1991

By D. G. Krige

Sampling data from large mined out areas of, existing Witwatersrand mines is split into areas accepted as 'mines' and used to provide for each mine the equivalent of a number of sets of borehole values as well as the follow-up 'actual' value. This data is used to establish the spatial structures on a macro scale between 'mines' for grade as well as variance and the suitability of the three-parameter lognormal model Is tested for the borehole and 'mine' frequency distributions. A comprehensive range of borehole valuation techniques is then applied to a large number of borehole sets on an individual mine basis. The results for each technique are then compared with the corresponding follow-up 'actual' values for these mines. After normalisation via the three- parameter lognormal model the estimates are also correlated with the 'actuals' to define any conditional biasses and to establish the observed error distributions and error variances of the estimates. On this basis the various techniques are rated for their relative efficiencies and the significance of the advantages gained.

Jan 1, 1992

By E. M. - Technical Papers Spokes

A.B. Rushton The work and resulting publications of the Committee on Underground Coal Mine Safety and The President's Commission on Coal were appropriate at the time of publication. The statistics cited in the publications appeared to be valid, and the actions proposed by the committee had merit. Although the actions proposed to achieve further improvements in safety may have been worthy of repeating, to associate statistics (Table 1) that are seven to eight years old with company names is bad. Statistics are readily available from the Mine Safety and Health Administration (MSHA) and are usually within three months of being up to date. A review of the most recent Coal Controlling Co. Report will reveal significant changes in the rankings. The more recent statistics should have been cited, or at least compared with those used in the article. Westmoreland Coal Co. is listed as having a 21.1 disabling injury rate for the period (1/78-12/80). The disabling injury rate for the Company for the year ending 1985 was 7.4 for the underground mines and 6.25 for the total facilities. Through March 1986, the dis- abling rate for the underground mines was 2.86. The management and employees of Westmoreland Coal Co. are committed to safety. The improvements achieved over the past five years attest to that commitment. We are justifiably proud of the achievement and dislike being misrepresented as in the April 1986 article Reply by E.M. Spokes I regret that the lapse of time since the original work gives a picture of safety practice that is no longer true today. That Westmoreland has reduced its disabling injury rate by 65% to 7.4 in 1985 is most commendable, and I congratulate you for this accomplishment. It is typical of the progress sought by the National Academy of Science and National Research Council when they funded the original study and published "Toward Safer Underground Coal Mines" in 1982. If a significant number of companies do as well as Westmoreland, the report will have served its purpose. Since the paper was primarily a condensation of the original report, it would not have been appropriate to seek access to later statistics. The purpose in seeking its publication at the time of presentation was to reach those who might have missed the original report. The fact that publication was delayed has not voided that purpose and may have reminded some who were aware of the original that its recommendations still apply to improvement of underground coal mine safety

Jan 1, 1987

By Leonard Sugin

The requirements of today's and tomorrow's markets led to a new generation of facilities which handles large tonnages annually, loading them into larger vessels, at higher rates, efficiently and reliably, with minimum labor input, and significantly greater attention to the environment. A great variety of products are handled, including various grades of metallurgical and steaming coal, coke, iron ore in its many forms, shapes and moisture content, phosphates and fertilizer products, bauxite and alumina ores, limestone, sugar and grains, cement and many other products. When we examine the annual tonnages involved in these movements the economic value of handling these products on a bulk basis can be readily seen. Although nearly all these products have been handled by continuous bulk conveyors for many years, recent governmental response to environmental concerns require a re-evaluation of previous procedures. Most air pollution and emission control regulations and ordinances have recognized several specific sources of pollution. Detailed regulations and requirements have been developed concerning smoke emissions, emissions of visible air contaminants and particulate matter from power plants, heating plants, refuse burning equipment, coke ovens, steel furnaces, kilns, and other industrial installations. Although fugitive dust is also an environmental pollutant it is governed by regulations that are more general and therefore, more difficult to apply. A general definition of a "fugitive particle" is any matter which escapes or becomes airborne from an operation or which is emitted into the atmosphere without passing or being conducted through a flue, pipe, stack or other structure designed for the purpose of emitting air pollutants into the atmosphere. This paper deals with the aspects of fugitive dust emissions as they apply to shiploading. Fugitive dust emissions control is important not only because of environmental regulations but also to prevent the loss of valuable product, reduce housekeeping, and reduce breakdown and maintenance problems to land and vessel equipment. The environmental controls for a belt conveyor system are those which will restrict the emission of fugitive dust particles and can be considered as follows:

Jan 1, 1977

By Edward C. Krug

"You are to use the word ... purely for its selling power. It is a name they venerate. As a result, you can use the word ... to ... get [them] to practice, not only without shame bit with a positive glow of self-approval, conduct which, if undefended by the magic word, would be universally derided." (C.S. Lewis, The Screwtape Letters, 1982, p. 162). "We need to tear everything down over a period of time and reconstruct a whole new world, planned top to bottom. "Right now there are just way too many people on the planet [5.3 billion]. `If we had ... an ethic ... we could cut back to 250 million-350 million people. `The United States is ... a bunch of pigs ... the average citizen ... [uses] maybe 70 to 80 times as much as anyone in the Third World.` "The indigenous pople were the ones that were right! I mean, they had their own religion, their own ethics and their own technology. We just went down a wrong road. "So when he says, `We got to rebuild the whole world,' you have no doubt this is serious sentiment .... And it is finally this world view that distinguishes (Ted) Turner as a media mogul and an environmentalist. It is why Worldwatch's Lester R. Brown told me Turner was `truly a visionary. "'(Interview of Ted Turner, Audubon magazine, November-December 1991. On Dec. 28, 1991, Ted Turner was name Time magazine's "Man of the Year." Clearly, media and environmental leadership agree with Turner's openly stated beliefs.)

Jan 1, 1992

By S. K. Kawatra, K. J. Shoop

An analysis of an iron-ore processing plant showed that its performance was affected by seasonal temperature variations, resulting in reduced grinding efficiency during the winter months. Laboratory and pilot plant studies were conducted to determine the cause of the observed loss of efficiency at lower temperatures. Two types of experiments were performed: drop tests and wet grinding tests. Drop testing was performed to determine the effect of brittleness and frozen pore water on the breakage characteristics of the ore. The wet grinding tests were divided into laboratory tumble tests and pilot-plant tests. The combined results of drop testing and wet grinding were used to make predictions on the performance of plant-scale autogenous grinding. From the drop tests, it was determined that dry iron ore, basalt and sandstone did not change in brittleness over the temperature range studied (-25º to 25ºC). However, when the rocks were water-saturated, the highly porous sandstone became considerably more fracture-resistant upon freezing, due to "grouting" of the pores and preexisting cracks by ice. This effect was not seen for either the iron ore or the basalt, because they were considerably less porous than the sandstone. Tumble tests on both laboratory and pilot scales showed that both the addition of fines to the test charge and a reduction in temperature caused a decrease in the amount of new fines produced. This reduced fines production was the result of increased slurry viscosity when either the fines content increased or the temperature decreased.

Jan 1, 1998

By B. W. Madsen

Experimental results obtained from large scale (7 tons), long-term (500 days) leaching of low tenor copper sulfide ores were interpreted by a geometric model involving the movement of a reaction zone through the ore fragments. The postulated leaching mechanism involved mixed kinetics and included diffusion of the reacting species through the host rock and a chemical reaction at the surface of the mineral particles. Ore properties which were considered were ore particle size and shape, grade of ore, and mineral content. Excellent agreement between the mixed kinetic model and the laboratory leaching results was obtained when minus ½ inch ore particles were not included in the leach. Also, a satisfactory prediction of copper recovery from plus ½ inch ore with a different particle size distribution was made; however, it was necessary to modify the shape factor in the model. Predictions of copper recovery from an ore sample which included the minus ½ -inch fine fraction and leaching for 460 days was 56.5 percent, and the recovery from leaching was 47.0 percent. The presence of fines caused channeling and uneven solution distribution and inhibited the leaching rate.

Jan 1, 1974