Search Documents

By Andrew W. Jenike

There used to be a time when bins were designed for total volume and placed in any available place of the plant. Poke holes were provided and feed was maintained by manual prodding, lancing, hammering, and by various mechanical flow-profiting devices. Little thought was given to what occurred inside the bins and why materials did not flow. Indeed, such mental effort was hard to justify while low-cost manual labor was plentiful, quality standards low, and rates of feed moderate. The past fifteen years have seen a drastic change in these conditions. We all know that labor for hard manual work is becoming unavailable at any wage, level. Standards of product uniformity are continuously rising. This uniformity is just as important in a fine ore feed to ball mills as it is in a cattle feed or in a flour mix. Rates of feed now frequently exceed 2,000 tons per hour per feeder. At that rate there is no time for, lancing or prodding. An efficient storage, plant contains a known available volume of bulk solid, and feeds it at the required time, at the prescribed rate, and without degradation of the product. A storage bin may also perform other functions such as blending of different grades, degasification of aerated, powders, isolation of different gaseous media. A contact bed of particles flowing by gravity in counter-current with a gas or liquid may be used as a continuous reactor. Gas or liquid pressures can be simply contained by, a sufficient head of flowing solid.

Jan 1, 1968

By D. C. Ridenour

The pressure system of ventilation with large diameter bore holes has been very effective in the ventilation of two gaseous mines, the Olga No. 1 and No. 2 Mines in McDowell County, West Virginia. The No. 4 Pocahontas Coal Seam on the Olga property lies 580 feet below the valleys. The seam is very gaseous as well as dry and dusty, which makes good ventilation all the more essential. Irregular and often extensive areas of the coal seam have been replaced with impervious shales and sandstones in "Fault" or "Want" areas. The replacement materials have sealed the methane in the coal seam and thus increased the quantity of gas that must be handled as mining is done. Often the No. 5 Pocahontas Seam comes down to meet the No. 4 Seam at the Faults and considerable methane is sometimes released from the upper seam. The factors mentioned, together with the irregular and unpredictable lateral shape' of the faults, result in long narrow stringers of coal that are very gaseous and difficult to mine. So far as the Olga Coal Company is concerned, the most effective ventilation under the conditions outlined has been the use of large diameter bore holes with a pressure ventilation system. The ventilation of a mine can be accomplished in two fundamental ways. The mine atmosphere maybe reduced below atmospheric pressure by an exhaust fan; or it may be raised above atmospheric pressure by a pressure fan. In either case, the coursing of the air is so planned as to have the haulage and traveling ways on intake air. While the majority of the coal mines in the United States, no doubt, use the exhaust system of ventilation, there are several advantages of the pressure system which are extremely beneficial.

Jan 1, 1960

By William Bogan, Mark Vaivoda, Richard Daniele

Many factors must be considered when performing engineering and construction work for a major minerals project. Dravo's Afton copper smelter in British Columbia illustrates some of the E&C factors considered when setting up this new operation. In March 1978, Afton Mines Ltd., a Tech Corp. subsidiary, began blister copper production at the world's first integrated copper ore mining, milling, and smelting operation to use Top Blow Rotary Converter (TBRC) process smelting technology. This key TBRC smelting element is licensed by INCO Ltd. to Dravo Corp. The TBRC process uses a single vessel of modular design. It rotates for mixing and provides complete processing capability, from concentrate through blister copper. The Afton facility is about 16 km west of Kamloops, a town in south-central British Columbia. To make its operation as economic as possible, Afton officials considered several options for the copper smelter, the first in modern times in the province. Inability to extract precious metals-primarily gold-from the concentrates ruled out hydro-metallurgical processes. The final choice was between a conventional electric furnace/ Peirce-Smith converter combination and the TBRC process. The TBRC process was chosen for its versatility in processing the various Afton concentrates and grades and its 40% lower capital cost compared to the electric furnace converter system. The TBRC smelter -including concentrate slurry receiving, drying, storage, smelting, off-gas cleaning, and copper casting-had an installed cost of about $25 million. In December 1974, a pilot program was conducted by Teck, Dravo, and INCO at INCO's Port Colborne, Ontario, research facility. The pilot program demonstrated the TBRC's ability to smelt, convert, and clean copper slags. After the successful pilot effort, Dravo performed additional research to find an effective fixation system for high grade, intermittent SO2 gases. Once the go-ahead was given, design and procurement for the Afton copper smelter was provided by the Denver Division, Dravo Engineers and Constructors. Commonwealth Construction, Vancouver, constructed all Afton facilities. Afton's single furnace smelter is designed to produce 25-kt/a blister copper in 363-408 kg cake form. The product is sold to England for electrolytic refining. The TBRC process is only one of several innovations proposed by Dravo and chosen by Afton to insure the most modern smelter in North America and meet all British Columbia's environmental restrictions. Conventional smelting methods use a separate furnace for each process step. The TBRC process employs but one furnace. The Afton TBRC vessel measures 6.4 m in length and 4.3 m in diameter. The furnace is supported on a set of motor-driven rollers. These permit the vessel to rotate at variable speeds to 40 rpm. Rotation provides good mixing, high reaction rates, and effective heat transfer from the refractory sides to the molten bath resulting in a low thermal gradient. The furnace can tilt through a full 360° for charging, firing, and pouring. Smelting at Afton is accomplished in sequential fashion. Flotation concentrate and limestone flux are initially charged to the hot, empty vessel. Using the water-cooled, oxy-fuel lance, the initial charge is smelted. Once sufficient molten bath is obtained and slagging completed, the metallic concentrate is charged. Materials are charged through the water-cooled, variable position additive chute mounted on the TBRC

Jan 10, 1980

By J. M. Dean, R. L. Grayson

Introduction With the continued downward pressure on coal selling prices, mine management must make its operations as efficient as possible. The problem is the same one throughout the mineral industries, streamlining operations to maintain competitive min¬ing costs (Born, 1991). There has been a great deal of research into better using production manpower. But the story is different for operations support personnel. Traditionally, planning man¬power requirements are done annually, with modifications to the operating plan occurring generally quarterly. On the other hand, the demands on manpower are often dynamic, being responsive to changing productivity levels, mine conditions (including water influx, bad roof, poor floor) and unanticipated project requirements (responses to machine breakdowns or a new section setup requirement because of a drop in coal quality in another area). Such changes may impact the manpower structure significantly. At times they may cause serious labor relations problems concurrently. Realignments and the generation of instability in the workforce because of active job switching (bidding) are a result. Most responses by coal operators are reactive rather than proactive, a situation that could be mollified by more accu¬rate and detailed planning of predictable manpower require¬ments. A manpower planning tool is needed that takes into consideration such things as changing productivity levels and conditions as manhour requirements for different work areas are planned, rather than blindly allocated through traditional staffing modes. Mine Management Support System The Mine Management Support System (MMSS) is an integrated decision support system that was developed using Sun Microsystems hardware according to the contract be¬tween the US Bureau of Mines and West Virginia University. The software used in the development of MMSS included X¬ windows (Scheitler and Gettys, 1986) for the user interfaces, LASER (Raman, 1985; Hayhurst, 1990) for the expert sys¬tem and graphics components, and the C language for general programming requirements. Sun DOS was used to allow the use of IBM-compatible applications software on the Sun networks. Sun OS is the operating system. It can be viewed as an enhanced version of UNIX. One of the components of MMSS that was developed to address the many specific objectives outlined in Grayson et al. (1990) is the work scheduling system. MMSS accom¬plishes work scheduling by using a mathematical (goal) programming approach to minimize the amount of switching of workers from their regular jobs to perform other jobs (Grayson and Nutter, 1991). Manpower support program The main objective of MANSUPP is to plan a detailed manpower structure for a mine by incorporating a production schedule, condition-modified work standards and manage¬ment preferences to predict required manhours for various support activities, for example, belt moves. This is accom¬plished by gathering and processing planning information the same way a mine planner would. The program is menu¬driven with the selection of a particular menu item locating the user in the appropriate area within the spreadsheet to review/add information. All of the interactions between productivity, section conditions and management prefer¬ences and their effect on the amount of support work required must be considered. Information regarding the productivity of a particular section, the geometry of the section, work standards for individual activities and section conditions must all be gath¬ered for input into the program. In the initial stages of development, it was decided that the program be developed in an environment that mine planners were familiar with in order to accommodate the use of the program. Lotus 1-2-3 or a compatible (Quattro Pro) met this environmental need. Other reasons included ease of calculation due to built-in functions, powerful command language and macro capabili¬ties. Each of the major components of the program defined are summarized. Production schedule This area allows the user to input a production schedule for the entire mine over 12 periods. Space has been provided for five sections, advance or retreat, and two longwall sections. There are several calculations occurring in this area that do not apply to the determination of manpower, but serve as an aid in production planning. Section description The section description area of the spreadsheet is shown in Table 1. The first three items are calculated in the production schedule area of the worksheet and then transferred to this location. The remaining information is input by the user to be used in later calculations.

Jan 1, 1996

By James S. Redpath

"The ways of the world be many and most of the ways be tried, you follow in the footsteps of others till you come to the great divide". These words, written by Robert Service a long time ago, come to mind when I think of our original attitude upon entering into a contract with the International Nickel Company to sink the deepest shaft in the world outside of the Union of South Africa. This shaft was to be sunk to a depth of 7,137 feet from surface, and while it was recognized by all concerned to be a somewhat unusual undertaking in our part of the world, the fact that quite a few shafts had already been sunk to this depth in South Africa probably gave us the feeling that we were following in the footsteps of others. In retrospect, because this shaft was being sunk under entirely different conditions than those existing in South Africa, we were in fact venturing into an entirely new area of endeavour without properly recognizing this fact. It has occurred to me that others considering a similar type of job could benefit from our experience, especially in an assessment of the risks involved and how they compare to those encountered in an ordinary shaft. For comparison purposes, I would define an ordinary shaft as being sunk to a depth of 5,000 ft or less, and a deep shaft as one being sunk to a depth of between 5,000 ft and 8,000 ft. The sinking of the Creighton No. 9 Shaft has been de-

Jan 1, 1997

By Jerome F. Machamer

Ninety percent of manganese is used as an alloying element in steel. Smaller amounts are used in dry-cell batteries, in aluminum and bronze alloys, and many other uses. The element has several oxidation states, and oxidation-reduction reactions control its chemical behavior. Manganese, in primary minerals such as rhodochrosite, rhodonite, and braunite, is in a divalent oxidation state, and manganese in secondary minerals, such as pyrolusite and cryptomelane, is in a quadrivalent state. Virtually all manganese ore production comes from three types of sedimentary manganese deposits. First, lenticular beds of manganese carbonate or carbonate-silicate rock in Early Precambrian volcano-sedimentary complexes in South America and Africa have been major sources of manganese ore. Second, laterally extensive beds of mangano-silicate and manganiferous carbonate minerals in certain banded iron formations are major sources of commercial ore and constitute the largest resource of manganese. Finally, manganese accumulations deposited in marginal to epicontinental basins are the largest source of current manganese ore production. Residual deposits resulting from the destructive weathering of rocks with a low manganese content have been, but are no longer, important sources of manganese ore. Most deposits have been altered to some extent by super- gene oxidative processes, and are economic because of that alteration. Outcrops of manganese ores are invariably oxidized and can be very deceiving as to the character of the underlying material. Nearshore facies of epicontinental basins, and nearshore age-equivalents of metalliferous black shales are among the targets for new manganese exploration. Very high-grade manganese occurs in sedimentary deposits altered by metamorphic and metasomatic processes.

Jan 1, 2001

By John S. Owens

The National Steel Pellet Project and the Butler Taconite Project are operated by The Hanna Mining Company in the vicinity of the towns of Keewatin and Nashwauk, on the western Mesabi Range. Production began in 1967, after seven years of exploratory and development diamond drilling and reconnaissance magnetic surveys, Previously, direct shipping hematitegoethite ores and gravity concentrates had been produced in the area from numerous open pits and several underground mines since the start of the century. Total shipments of these oxidized ores amounted to more than 200 million tons, but at the present time such reserves are nearly exhausted, and there are no mining operations in the Keewatin-Nashwauk area except at the two taconite projects. The locations of all of the present taconite operations on the Mesabi Range are shown in Figure 1, extending for a distance of about seventy miles from the Butler plant to the Dunka River area. The Butler and National plants have a combined rated capacity of 4.4 million tons of pellets. Their reserves cover a combined strike length of about eight miles on the Biwabik iron formation. All of the intervals between present taconite operations on the Mesabi are potential sources of additional magnetic taconite; in particular, exploration and economic studies have been carried out by Jones and Laughlin Steel Corporation in the Biwabik area between Aurora and Virginia, and by Pickands Mather and Company in the Hibbing area. However, west of the Henna and Butler holdings, it appears unlikely that magnetic taconite exists in commerical quantities at economic depths due to extensive oxidation of magnetite to hematite.

Jan 1, 1968

By D. Christofferson

As an alternative power source to eliminate trailing cables, ESD Corporation is installing a flywheel system on a shuttle car. Flywheel power is extracted by a high-speed generator, developed by Lear Siegler Corp,, and the system -- including vacuum and lubrication and cooling auxiliaries -- is supplied by the aerospace group, Rocketdyne Division of Rockwell International. The flywheel system is being developed under a three-year contract with the Department of Energy. It is a follow-up contract to a previous DOE-contracted study by General Electric Co. in which it was shown that a flywheel can be a feasible power source for a shuttle car from technical, economic, and safety standpoints. This paper addresses the status of the program, design decisions established, and plans for laboratory test procedures and underground demonstration. The flywheel-powered shuttle car is a conventional 6-ton capacity shuttle car equipped with a 7-rotor flywheel energy storage package. The energy package is the sole source of power for the shuttle car through a complete mission duty cycle (MDC) of tramming to the miner, receiving a load of coal, and returning to the secondary haulage system. Energy stored in the system exceeds MDC requirements and waiting times to provide an ample margin of reserve energy. The energy storage system is recharged by spinning the rotors back up to maximum speed each time the shuttle car comes back to the secondary haulage system. The electrical charge motor is connected to a power source to recharge the system while the load of coal is being discharged.

Jan 1, 1982

By William T. Folwell

INTRODUCTION - CURRENT RAISE BORING PRACTICES Raise boring is a comparatively new tool to the underground mining and construction industries. Underground raise boring, in this country, had its beginning in the early 1960's, in the iron mines of Michigan. These first raises were bored 40 in. and 48 in. in diameter with maximum lengths of approximately 200 ft. Since the late "sixties", the raise boring machine has been accepted by the mining industry as an important machine to increase excavation rates, provide adequate ventilation airways, improve safety, and reduce costs, to name a few of the benefits. The construction industry is now accepting raise boring techniques for hydro-electric power projects, water supply projects, tunnel projects, waste water projects, etc. Raise drills are now capable of boring raises to diameters as much as 12 ft, in the softer rock types. Raise lengths range from 200 ft to as long as 1700 ft. Bored raises, in general, are bored at dip angles ranging from 45º to 90º, depending on the requirement of the raise. The general practice is to drill the pilot hole down to an opening below and up ream the pilot hole to the required diameter. The pilot hole (9-7/8", 9", 11", or 12-1/4" diameter) is generally drilled with compressed air to remove the cuttings. In the event that ground water is encountered and removal of cuttings is impeded, a foaming agent is added to assist in lifting the cuttings. When excessive water is encountered, water is used as the circulation medium and the cuttings are removed by pumping. During the reaming cycle, the cuttings fall by gravity and are removed from the bottom of the raise by conventional methods.

Jan 1, 1997

By Trevor R. Ellis

In this paper a method is presented for estimating the specifications of sandstone-type uranium deposits which will be the minimum that can meet a company's economic requirements for investment. The method interpolates and extrapolates from available cost data for typical mines to provide the costs for a wide range of possible deposits. The range of deposits achieving the company's required discounted cash flow rate of return on investment at an estimated uranium oxide selling price is then calculated, thus giving the complete range of deposits which meet the minimum required specifications. Prospects are then evaluated by comparison with these minimum requirements.

Jan 1, 1979

By R. Cohen-Alloro

Classical apparatus for granulometric separation generally have limited applications which are found either in the level of the size of separation or in that of the accuracy and the efficiency of the separation or in that of the rate of feed. In industrial practice, the classification of the products of coarse dimensions generally poses no problems. On the contrary, the separation of fine particles presents some difficulties, however the apparatus is used (mechanical classifiers, curved screens and sieves, hydrocyclones, etc...). These difficulties are due to hprfections of separation, rather high cost prices, and sometimes large amounts of recycled materials.

Jan 1, 1970

By L. H. E. Weyher

The Bethlehem Mines Corp. is a captive mining subsidiary of Bethlehem Steel Corp. Its coal production is tied to the demands for and production of steel, a situation that has to balance between the following two extreme strategies: (1) either the mines are designed and operated for some optimum production level and the demand fluctuations within the steel corporation are met by supplementary corporate coal sales and purchases, or (2) the mines absorb all the demand fluctuations, regardless of the effects on mine costs. A rational definition of the best strategy between these extremes is, of course, needed but is very difficult to formulate in view of the complexity of the many factors that would have to be included in the analysis. Consequently, rather than setting profit targets for each given mining division and/or individual mine, the practice evolved to set production targets for producing specified tonnages of coking coal for shipments to the ovens located at the corporation's iron and steelmaking plants. This in turn leaves the mines with the dilemma of having to explain demand-related cost-per-ton fluctuations while essentially depriving them of the ability to control profit through tonnage optimization. In the early 1970's, the coal prices rose significantly, while other factors led to sagging productivity in underground coal mining. Thus, the role of Bethlehem's coal operations in the corporate profit picture gained in relative importance. This, in turn, sparked a closer attention to the coal mining cost structure and factors controlling productivity. At the same time, the drastic increase in the capital needed to open a new mine also increased the amount of planning required to minimize risks. All of this called for more well-defined, quantitative operating data. Bethlehem therefore launched, in the early 1970's, a number of innovative steps that, as the future may show, represented pioneering contributions to the growing sophistication of North American underground coal mine planning and management control practices. This case study describes the changes that led to the current implementation of a novel production reporting system at Bethlehem's coal mines. These changes took place in two distinctly different phases. The current system that resulted from the Phase II developments utilizes, of course, experience gained earlier and is expected to be amplified to incorporate more advanced concepts and technology as future experience dictates.

Jan 1, 1979

By Earl G. Hoover, V. S. Znamensky

For most geologists and miners the term asbestos refers to a group of highly fibrous silicate minerals that readily separate into long, thin, strong fibers of sufficient flexibility to be woven; these fibers are heat resistant and chemically inert, and possess a high electric insulation and therefore are suitable for uses where incombustible, nonconductive or chemically resistant material is required. The US Mining Safety and Health Administration (MSHA) specifically refers to the naturally occurring minerals chrysotile, amosite, crocidolite, termolite asbestos, anthophyllite asbestos, and actinolite asbestos as asbestos if the individual crystal fragments have the following dimensions: length-greater than 5 µm; maximum diameter-less than 5 µm; and a length to diameter ratio of 3 or greater. Since asbestos has been identified as one of the ten most carcinogenic substances (a cancer-causing agent), it has become, for many government regulatory agencies, a major issue concerning banning emissions to the environment. Very few recent issues have caused as much concern for the crushed stone industry as asbestos. Complicating the problem is the fact that several federal and state bureaus have greatly compounded the confusion because each has become involved in the asbestos dilemma. Simple solutions to a very complex problem have been proposed by these various governmental groups. In addition to governmental bungling is the fact that public interest groups have been able to use federal and state laws that have been enacted with a strong environmental bias to foment even greater complexities. Such is now the state of the asbestos problem. No con- firmed health risk has been associated with low-level exposure, namely crushed stone in an unbound form; a methodology for sampling and analyzing for asbestos has not been developed; a precise definition of what is asbestos does not exist, nor does a concensus among the various government groups as to what course of action to pursue. Pure asbestos as it is mined for commercial purposes does not exist in the properties mined by the crushed stone industry. Where the six asbestiform minerals do appear (to date we've been referring mainly to chrysotile in serpentinite formations in Maryland) the amount of the asbestiform mineral present is generally quite small. They generally appear in scattered, miniscule amounts. In the case of Rockville Crushed Stone in Montgomery county, Mary- land, the chrysotile is less than 1/2 of 1% of the rock deposit. No health risk has been identified with such minute quantities of asbestos minerals. MSHA standards for the occupational health and safety of quarry workers are being met; and there is every indication that normal background levels of asbestos, throughout the surrounding countryside, are as high or higher than levels measured on roads where the rock is used in pavement or base. The problem and the controversy lie with improper terminology on the part of so-called public interest environmental groups, aided and abetted by some governmental agencies who, to be charitable, we can best describe as uninformed. The news media frequently has fanned the issue, unintentionally we'd like to think, by quoting these misinformed authorities and not bothering to question the facts or adequately report balancing information handed to them. It is much better copy to talk about an asbestos cancer scare, than to deal with rather mundane measurements and descriptions that are hard to understand. At the heart of the issue is the improper use of the word asbestos. Instead of being confined to the geological description of the six asbestiform minerals-chrysotile, amosite, crocidolite, termolite asbestos, anthophyllite asbestos, and actinolite asbestos-the word asbestos is also wrongly used, but too-frequently to identify many other minerals that happen to have elon-

Jan 1, 1986

By J. E. Gebhardt, H. Toro, K. Y. Lee

Industrial-scale test results indicate superior metallurgical performance of column flotation compared to conventional cell flotation for copper cleaning. A technical comparison of bubble generation systems for column flotation is made. Two types of bubble generation systems are considered: the filter-cloth type spargers and the Turbo-Air® sparger, which utilizes an air-water mixture fed to the column through injection tubes. Examples of the improved technical performance available with an external sparger system are presented using data from plant tests conducted for specific applications with several different mineral ores. INTRODUCTION Column flotation is now a valuable unit operation which mineral processing engineers employ in the design and operation of flotation circuits in nearly all mineral applications. The acceptance of columns in the mid- 1980s by the minerals industry was paralleled by a rigorous approach to developing a scientific understanding of the design, scale- up, and operation of column flotation units (Finch and Dobby, 1990). Since then, column flotation has become a standard unit of the cleaning stage in many new mineral concentrator projects and has replaced older mechanical cells to improve process efficiency. The size of column cells has continued to grow from the initial 0.9- to 2.1 -meter diameter range, and it is not uncommon to find column cells today being 2.7- to 3.6-meters in diameter. With the success of the smaller units, the scale-up to larger cells has been proven and demonstrated by the performance of the large-diameter cells (Murdock and Wyslouzil. 1991). The use of columns in flotation circuits has also been accompanied by developments in modelling. control, and optimization of column performance (Lee et al, 1991). The bubble generation system is the heart of the operation of column flotation cells. The most common methods for generating bubbles can be divided into two types: the internal and external spargers. Internal spargers are typically a porous material, such as sintered glass, porous rubber or filter-cloth, or maybe a single- or multi-nozzle sparger. External spargers implies that a gas and a liquid (either water or slurry) are brought into contact outside the column and that mixture is then introduced into the column. Several types of external spargers are available today, and innovative designs for externally mounted air sparging systems have been a significant factor in the successful application of columns. Early types of bubble generation systems.

Jan 1, 1993

By C. Y. Chen

Public Law 75-87, the Surface :mining Control and Reclamation Act of 1977 (SMCRA), Section 516(b) requires the underground coal mining operator to "adopt measures consistent with known technology in order to prevent subsidence causing material carnage to the extent technologically and economically feasible, maximize mine stability, and maintain the value and reasonably foreseeable use of such surface lands, except inn those instances where the mining technology used requires planned subsidence in a predictable and controlled manner . . .?. The Congress also directed the Secretary of the Interior to promulgate regulations to implement the law. As a result, the control of subsidence from underground coal mining to minimize surface damage has become the mandate of a Federal law. This paper discusses the mechanics of subsidence and the effects of subsidence on ground features and also summarizes some of the measures which have been used to minimize the possibility of damage to surface structures as a result of subsidence due to underground coal mining.

Jan 1, 1981

By Fred N. Kissell, George H. Jr. Schnakenberg

INTRODUCTION A variety of instruments are available for measuring or monitoring the performance of underground mine-ventilation systems. In general terms, the instruments may be classified as those that measure air velocity and those that measure gaseous concentrations. All costs herein are in terms of 1978 US dollars. The mention of a specific manufacturer or device is not intended to be an endorsement by the US Bureau of Mines. AIR-VELOCITY INSTRUMENTS The basic instruments used for measuring the air velocity in mines are the vane anemometer and the smoke tube. Vane Anemometer Of the air-velocity instruments, the 102-mm (4.0¬in.) vane anemometer is the most common and is available as either a low- or high-speed type. The low-speed anemometer generally is the most suitable for measuring the velocities in ordinary airways. For a rough check of the velocity in an airway, it usually is satisfactory to hold the anemometer by hand, positioning it in the center of the airway for 30 sec. However, the resultant error may be as high as 25% , and such a hand-held approach is unsuitable when accurate or reliable measurements are required. To obtain more accurate measurements, the proper procedure is as follows: 1) Since holding the anemometer by hand generally causes the instrument to read about 15% high, it is mounted on a 0.6-m (2-ft) extension rod. 2) The airway is divided into equal right and left halves. A 1-min traverse is used in each half, moving the anemometer smoothly up and down in a zigzag pattern so that the entire half is covered within the allotted minute. 3) The manufacturer's correction table is applied to the readings to adjust the velocity calculation as necessary. Whenever possible, anemometer readings should be obtained in a long straight section of airway that has a constant cross-sectional area. Bends and obstructions should be avoided, since they cause turbulence and other discontinuities in the airflow and can degrade the accuracy of the velocity measurements. Although a series of velocity measurements at one location usually corresponds to within a few percent, this is not an indication that the airflows calculated from those readings are completely accurate. One reason is that the correction table provided with the instrument generally is not for that specific instrument; instead, it represents the average correction for all such instru¬ments made by the particular manufacturer. Most cor¬rection tables specify a correction factor of from 0 to 15%, depending upon the velocity. However, even after correction, the instrument error still may range from 3 to 5%. At low velocities such as those below 0.76 m/s (150 fpm), the instrument error can be two or three times greater than this, ranging from 6 to 15%. The new ball-bearing anemometers generally perform somewhat better at low velocities than did the older conventional anemometers. Another source of error is introduced when measur¬ing the cross-sectional area of the airway or entry. Under the best of circumstances, measurement errors, instrument errors, and a host of other minor errors all combine to cause a total error of at least 10% in the velocity calculation. The vane anemometer also can be used with reason¬able accuracy to measure airflows in mine-ventilation ducts. In this application, the anemometer is mounted on a rod and is held at the center of the duct end. For a duct that is discharging air, the average velocity in the duct is 85% of the centerline reading (Northover, 1957). For a duct that is taking in air, the average velocity is 70% of the centerline reading (Haney and Hlavsa, 1976). To measure the airflow discharged from a regulator or from a small hole in a stopping or bulk¬head, a correction factor for the area is necessary. A good approach in this situation is to traverse the area of the regulator or hole, holding the anemometer with an extension rod. This provides an average velocity that is multiplied by 85% of the measured area of the regulator or hole. In all cases, the manufacturer's instrument cor¬rection table must be used and applied properly. For accurate results, the anemometer should be returned to the manufacturer for periodic cleaning and checking. If it is in daily use, the anemometer should be returned about once per year, and proportionally less frequently if the usage is less frequent than on a daily basis. Smoke Tube The smoke tube may not appeal to individuals who believe that good measurement results can be obtained only with expensive, complicated, and fragile instru¬mentation. Nevertheless, smoke works about as well as anything for the routine measurement of low air velocities in mines. The following procedure yields reasonably good results: 1) Two marks are scratched 7.6 m (25 ft) apart on the floor of the airway. 2) The smoke tube is used to release a cloud of smoke in the center of the airway, about 0.9 m (3 ft) upstream of the first mark on the floor. 3) A timed interval begins when the leading edge of the smoke cloud passes over the first mark, and the interval stops when the leading edge of the cloud passes over the second mark. 4) A factor of 20% is subtracted from the cal¬culated velocity to determine the true average velocity, providing a correction for the centerline and for the spreading effect at the front of the cloud. Velocities calculated with the preceding method generally are accurate to within 10 to 15%. In some instances, the cloud from a conventional smoke tube

Jan 1, 1982

By Larry B. Bramlett

Regional radiometric, magnetic and geologic data point to Copper Mountain as an area of general uranium favorability. Sub-regional radiometric and magnetic data direct interest to a specific section of an overthrust Precambrian granite. Detailed magnetic and resistivity surveys in this area show local targets of interest, one of which corresponds to Rocky Mountain Energy's North Canning deposit. On the basis of these data a second and previously untested target was drilled resulting in the intersection of uranium horizons similar to those at North Canning. This integrated geophysical approach can be used for uranium exploration in geologically similar areas.

Jan 1, 1979

By Boris K. Krstev

INTRODUCTION The flotation process, in the real industrial complexes, is characterized by the existence of the significant number of the close reciprocal interrelationship between the input and output Darameters. Traditional complexity is appeared with regard to absence of the suitable a priori information for the physico-chemical characteristics of the flotation process. It’s led to needful of taking of consideration about the undefinition which have got the place in the real conditions and application of the statistical methods. The identification of the flotation process through statistical methods is conception of the more-stages procedure, including the collection and previous analysis, the choice of the model structure and valuation method, the estimation of the model un- known parameters and the results interpretation. The essential concept for the subject of this paper belongs to the empirical models ("black-box") and deals with optimizing in constant industrial plant process. The offered method envisages the application of process operation data in order to improve the work process or constant accomplishment of better results for the target function in relation to the former achievement. The optimum process solution isn't afixed value under the influence of various factors, but "a moving point" along the response surface and deviates from the scheme solutions. The evolutive planning method constantly "investigates and approaches" the optimum solution for the selected target function. As a matter of fact the expert operates the plant without interrupting the normal work process. The essential concept of method is to attain changes in the standard conditions, but so limited that they will not effect either production or the product. This method is based on statistical concepts and availability of following the risk of error. The possible influental factors for the flotation process (m=l, 2, 3) is following: the metal content in the feed ore; production level (t/h); grinding fineness in the flotation pulp; pH-values; the consumption of collectors and modifiers The possible target functions are: the recovery of plant capacity, metal recovery in the concentration process and concentration quality. The application of the evolutive operativity method in the chalcopyrite flotation- Bucim concentrator, combines the statistical data and the operator's experience in the interpretation and making a decision which adds up to the precise automatic performance of the process. The advantages of this method in relation to the existing procedure for the flotation process are the following: • The method is unexpensive and losses are reduced to the time necessary to collect the data and record them in the computer. This method provides a constant process control and a quality decision which is better than those brought by an ex- pert with great experience ("hit-and-miss method"). • The method also provides incidental data about the effects. • The method should not be considered as a procedure for solving an incidental problem ("crash program"). • The obtained results must be interpreted by an appropriate expert in order to be considered instructive. MATHEMATICAL STATISTICS Taking into consideration the complexity of the enrichment processes it's necessary the application of "black-box" and mathematical modelling. The presence of the indefinite elements compel us towards the both theory of the probability and mathematical statistics. The mathematical statistics by the mineral processing investigation of the valuable raw materials in the last years has had greater signifance and widely spread application. The application of the mathematical statistics methods for the technological pro- cess analysis and the construction of the mathematical models is bound up by the task putting of the automatic control system de- sign (Fisher R. A. 1941, 1949). The statistical analysis in the enrichment processes is applied formerly, especially in the sampling estimation. Contemporary, in the last years is imposed the tendency of mathematical statistics application for the obtaining of quantity characteristics and quantity valuation from the individual influental factors. Above mentioned tendency in the significant level is based by the mathematical statistics development as a mathematical discipline close connected with the technical cybernetics general joining to the investigated object as a "black-box". Another essential factor in the mathematical statistics development is appeared the created mathematical theory of experiments as a new, to some extent, autonomous statistical domain. The theory of experiments has demonstrated exclusively importance for the investigation of the complex more-factorial processes in the chemistry, mineral processing, metallurgy etc. The investigation by the enrichment processes of the valuable raw materials and their management is possible by the statistical method application. In the same time, it's possible to use the wide-spread traditional methods of the statistical analysis, such as the methods of the dispersion, correlation, regression etc. Also, it may be mentioned above all the methods of the statistical planning of the extreme experiments. The more perspective are representatived some cybernetic methods which are based by the probability as an approach in the process analysis, for example, the identify of the ways and forms, the graph application as an additional instrument in the correlation analysis, the dynamic programming etc. The mathematical statistics application in the laboratory investigation scale is connected above all by the experimented material analysis and the compact representation of the obtained results. The mathematical statistics methods are more varrying and may be applied in the investigations of the wide circle of problems

Jan 1, 1996

By T. J. Carew

INTRODUCTION The application of micro-computers to the evaluation of an advanced exploration project is illustrated by reference to a large project in the Sudbury Basin region of Canada. The deposit in question is polymetalic (Cu, Pb, Zn, Au, Ag) with a strike length of 3048m (10000ft) and has been explored to a depth of 457m (1500ft) by approximately 1350 diamond drillhole of between 9 - 305m (30-1000ft) in length. The large amount of data involved and the ability to rapidly recalculate geological reserves in response to fluctuating metal prices were key factors in the application of a micro-computer based evaluation system. The evaluation software was implemented at two levels, with data capture implemented mainly on - an entry level workstation comprising an IBM-PC compatible (PC-XT) micro-computer equipped with a 20Mb hard disc, printer and RS-232 serial communication facilities. Data analysis, display, geo- logical modelling and processing was carried out on a high-level workstation based on a Hewlett-Packard 9000 super- micro computer and peripherals, including a 40Mb hard disc, tablet digitizer and plotter. Basic drillhole data was entered either directly at the super- micro or transferred from the PC via the RS-232 link. The evaluation process proceeds once the data is edited and in a "clean" format within a master project database. The software is comprised of a suite of modular, integrated programs based on ease of use, interactive graphics and optimized for the computer workstation. Drillhole data was displayed and plotted as hard copy plots on which geological interpretations were developed. The data was copied into small manageable projects consisting of 100 to 150 drillholes, within which a sectional model was created such that all the models are interconnected along the entire strike with no overlaps. Geological reserves were derived by developing a set of function variables, including Net Smelter Return, within the database. The values of these functions can be displayed on the model sections and "ore” zones defined in accordance with pre-determined cutoff values. Interpolation of the modelled data was then carried out and geological reserves calculated and reported. DATA CAPTURE Drillhole data for the project consisted mainly of existing drillhole logs, although the system allows for the entry of new information as it becomes available. The structure and format (i.e. number and length of variable fields) is user defined. The log for this project comprises an abbreviated section for name, competency, grain size, texture, colour and alteration. Fields are defined for structural information regarding bedding and fault angles and up to seven mineral identification columns and percentages are available. Assay information consisting of the sample number, width and six determinations (Cu%, Pb%, Zn%, Fe%, Au opt., Ag opt.) along with a comments section of 25 characters completes the log. One powerful feature of the data- base is the ability to set up function variables that are mathematical and/or logical combinations of the project variables, enabling the user to develop economic variables such as Net Smelter Return. These functions include current treatment costs, deductions and penalties and can be rapidly recalculated within the database to accommodate changes in metal prices, forecast recoveries and exchange rates (Table 1).

Jan 1, 1987

By S. C. Gambrell

The practice of roof bolting in world-wide mining activities is very well known, having been used extensively for over 50 years. The theory of roof bolting, however, is extremely complicated, and only recently have investigators attempted to explain the theory. Discussions of the mechanics involved usually originate with actual experience gained in the use of roof bolts. The use of roof bolting in mines has grown dramatically during the period after World War II. Other scientific techniques have emerged in mining research in the same period. Included in these techniques is the study of rock mechanics, which has now developed into an impressive research effort. Various means of analysis have been utilized in rock mechanics, most of which reduce rock to an isotropic, homogeneous medium that could be easily analyzed. Because of the inherent nature of rock, direct research methods frequently are not certain to provide satisfactory results, whereas indirect methods must idealize a given set of conditions in order to be useful. One of the indirect research methods is the photoelastic technique, the theory of which is widely known and needs no elaboration. This technique has been used extensively to examine the state of stress around underground openings of various shapes in certain types of strata, and under various configurations (1,2,3,4,5). Much of the theory used now in the design of underground openings is based on photoelastic evaluation. Unless rigorously applied, how- ever, the photoelastic technique is at best a qualitative means of evaluation. It is useful, however, for unusual examples which can be more or less easily analyzed to obtain the overall state of stress which could not be determined by other means. Little work has been done in the photoelastic analysis of rock bolting, mainly because direct research techniques have proven useful.

Jan 1, 1970