Search Documents

By D. Royston

Mill liners provide the wear-resistant surface within grinding mills, they also impart motion to the mill charge, ie the grinding process, by providing the key between the charge and mill shell, and, at the discharge end, they remove the ground contents of the mill. As semi-autogenous grinding (SAG) mills have grown in size the process aspects of liner design and their impact on mill performance have become particularly important. While feedback from practical experience is critical to good mill liner design, increasingly sophisticated computer-based tools are being developed to assist in mill liner design.

Jan 1, 2007

This paper presents the development of a regrind facility design at BHP Billiton's Leinster Nickel Operations (LNO) in Western Australia. The recovery opportunity was identified from an analysis of plant operating data together with scanning electron microscope (SEM) measurements on relevant tailings streams from LNO. A laboratory procedure was developed to determine the potential recovery improvement of installing a regrind facility at LNO. The last step in formulating the process flow sheet and defining the process design criteria was to construct and operate a pilot plant, which incorporated four banks of flotation cells and an Xstrata M20 Isa Mill. Pilot plant on/off trials were used to define the expected metallurgical benefit. A prefeasibility engineering design and cost estimate was completed. Following a successful internal business evaluation, a feasibility study is currently underway.

Jan 1, 2007

By T. Aoki, Y. Maeno, R. Kawano, F. Nakahara, Y. Obara, K. Shibata

The mechanical behaviors of fully-grouted long-embedded cablebolts actually used in situ are very non-linear in pull tests and are different from those of short-embedded cablebolts. We have conducted the pull tests of long-embedded cablebolts installed in mockup rock test blocks, which are 4m in the longitudinal length. In order to investigate the mechanical behaviors inside the test block, the axial load distribution along the cablebolt and locations of acoustic emission events were measured during each pull test. It was found that the axial force distributions were quite linear and that the gradients were interpreted as the grout bond strength by taking into consideration the stress balance at the infinitesimal segment of a cablebolt. Les boulons-câbles longs entièrement cimentés qui sont réellement utilisés sur place présentent, au cours des essais de traction, des comportements mécaniques considérablement non linéaires et différents de ceux des boulons-câbles courts. Nous avons mené des essais de traction des boulons-câbles longs installés dans une maquette de fond rocheux servant d’éprouvette d’une longueur longitudinale de 4 m. Afin d’étudier les comportements mécaniques intérieurs de l’éprouvette, la répartition de la force axiale du boulon-câble et l’émission acoustique ont été mesurées durant chaque essai de traction. Il s’est avéré que les répartitions de la force axiale sont sensiblement linéaires et que leurs gradients représentent la résistance d’adhésion en prenant en compte l’équilibre de contraintes à la partie infinitésimale d’un boulon-câble. Das mechanische Verhalten von ganz eingegossenen, lang eingebetteten Kabelbolzen, die vor Ort eingesetzt werden, ist bei Zugprüfungen sehr nichtlinear und anders als das von kurz eingebetteten Kabelbolzen. Es wurden Zugprüfungen mit lang eingebetteten Kabelbolzen durchgeführt, die in Prüfblöcken (Gesteinsattrappen) mit 4 m Länge eingelassen waren. Zur Untersuchung des mechanischen Verhaltens in den Prüfblöcken wurden die Axiallastverteilung entlang des Kabelbolzens sowie das Auftreten von Schallemission im Verlauf jeder Zugprüfung gemessen. Es ergab sich, dass die axiale Kraftverteilung recht linear ist, und die Gradienten wurden unter Berücksichtigung des Kräftegleichgewichts am infinitesimal kleinen Punkt eines Kabelbolzens als Haftfestigkeit interpretiert.

Jan 1, 2003

By B. M. Kunar

It is well known that job-related hazards and individual factors influence occupational injuries. However, research involving coalminers has been limited. This case-control study assessed the relationships of job-related hazards and individual/life style factors with injuries among underground coal miners. It compared 245 cases with at least one injury during the previous two-year period with 245 matched controls with no injury. The data were gathered via personal interview and analysed using the conditional logistic model. The significant risk factors were materials handling (adjusted OR 5.15), poor environmental/working conditions (2.63), geological/strata control-related hazards (2.35), lack of formal education (3.00), sleep disorders (1.86), alcohol consumption (2.32), disease (2.23), having a large family (5.40), and risk-taking behaviour (9.40). Machine-related hazards, sleep disorders and alcohol consumption primarily affected workers aged less than 45 years; whereas, environment/working condition-related hazards, presence of disease, smoking, risk-taking behaviour and large family size were more likely among workers aged 45 or over. Keywords: Occupational injuries, sleep disorders, job hazards, alcohol, coal miners

Jan 1, 2010

By K. G. Tshilombo

It should be possible to use an oxygen probe to follow iron removal during converting, if local equilibrium is established between iron in the matte and the iron oxides in the fayalitic slag. The oxygen activity is expected to increase strongly as the iron content of the matte decreases (and the iron activity in the matte drops) while the iron oxide activity in the slag remains constant. To test this idea, oxygen activities were measured in synthetic mattes (made up of mixture of Cu2S, FeS and Ni3S2) when in contact with silica saturated SiO2-FeO slags, and silica and (initially) magnetite saturated SiO2-FeO-Fe3O4slags. The measurements were performed on laboratory scale at 1250°C, using an oxygen probe consisting of a stabilized zirconia electrolyte and Fe/FeO reference, and containing the sample in a silica crucible. Electrical contact to the matte was by means of a platinum wire. The measured oxygen activity was sensitive to the iron content of the matte, and insensitive to the composition of the gas atmosphere over the melt. The measured oxygen activity was generally close to that predicted by Fact Sage calculations. This indicates that such oxygen activity measurements could be useful to monitor iron removal during converting of nickel-copper-iron mattes.

Jan 1, 2006

By G. E. Blight

Many mines engaged in deeplevel gold mining in South Africa are experimenting with the use of tailings fills, or are implementing tailings backfilling programmes on a limited scale. The approach varies from mine to mine, depending on circumstances and available fill materials. Several mines are backfilling with a cyclone underflow product; the cyclone overflow is then combined with the balance of the tailings stream and directed to surface disposal. As the extent of backfilling increases, the proportion of the surface tailings stream composed of overflow material will rise, and the properties of the tailings requiring surface disposal will approach those of the cyclone overflow. As the latter will be finer, less permeable and possibly weaker than the total tailings currently being disposed, the design and operation of surface tailings dams will have to be modified. Dams may have to be designed with flatter outer slopes of a reduced maximum height. Lower rates of rise may be required and, as a consequence, larger disposal areas may be demanded. To offset the negative aspects is the fact that the quantity of tailings requiring surface disposal will be reduced. The paper explores the dam-building properties of two cyclone overflow products. It shows that although these materials are inferior in dam-building characteristics to the corresponding total tailings, their geotechnical proper- ties still fall within, or close to, the range of properties typical of gold tailings. Although the design and operation of tailings dams may have to be modified, existing technology is adequate to handle these changes.

Jan 1, 1988

The first neutrinos in nature ever detected by man were "caught" in a unique laboratory some 3 km (over 2 miles) underground in one of the world's deepest mine shafts at East Rand Proprietary Mines (ERPM), Boksburg. Only 100 m from where gold is being mined from the rock face a small team of South African and American physicists work on one of the most fascinating and important fundamental research projects that is currently exciting the imagination of the scientific world. Neutrinos are sub-atomic particles just as are protons, neutrons and electrons, but they are unique in that they have neither electric charge nor mass. Cosmic neutrinos travel at the speed of light and penetrate stars and planets. Even a million kilometres of solid lead would not provide a satisfactory shield against them. Stars are believed to "burn" by means of nuclear reactions which produce enormous fluxes of neutrinos. The sun, for example, illuminates the earth with visible light, but also bathes it with neutrinos. After World War II, two American physicists, Profs Frederick Reines and Clyde Cowan, experimenting at a large nuclear reactor, succeeded in obtaining direct evidence of the existence of the laboratory-produced neutrino. It then became very important to establish whether neutrinos also existed in nature. This knowledge would lead to a greater understanding of the forces of nuclear physics, of the behaviour of nuclear particles and, indeed, is also relevant to astrophysics. From the start it was clear that the search for "natural" neutrinos would be difficult. Questions which arose were- * how could they be traced if they were without mass or electric charge? * how could other nuclear particles be screened off? * could these not be wrongly detected, or even prevent accurate detection of neutrinos? Neutrinos were known to be produced along with charged particles, by the reaction of primary cosmic rays with the constituents of the atmosphere. It was also known that when the neutrinos collided with matter, they themselves produced the same type of charged particle which could be detected if the unwanted charged particles from the atmosphere could be screened off. What was needed, therefore, was a laboratory where the particles produced in the atmosphere could be screened out, yet which would receive and detect the particles produced by the neutrons' collision with the matter (solid rock) in the vicinity of the laboratory. This meant that scientists either had to build a laboratory with an enormously thick lead shield for their detection work. . . or they could go as near as possible to the centre of the earth where only charged nuclear particles of the very highest energies could penetrate. ERPM was clearly the most suitable place in the world where so effective a "neutrino trap" could be set. Under more than 3 000 m of solid rock the apparatus for detecting neutrinos is well shielded against unwanted nuclear particles produced in the cosmic radiation which can reach the laboratory only in a steeply vertical trajectory. Other particles are easily stopped by the great thickness of rock. The air-conditioned laboratory is at one end of a 150 m long tunnel, 2,5 m high and wide, blasted from the rock. The electronic recording equipment is housed here, while the rest of the tunnel is filled with the detection system. When a charged particle passes through a detector element, it produces a minute flash of light which is recorded and which triggers a flash-tube array. This then defines the trajectory of the charged particle, which is also recorded on film for analysis. So far 82 neutrinos have been detected, 50 at the present level and 32 at a higher level, and the findings have borne out the physicists' theoretical expectations. In this joint project Profs Reines, J. P. F. Sellschop, Director of the Witwatersrand University's Nuclear Research Unit and M. F. Crouch of the Case-Western Reserve University of Ohio are the Chief Investigators. This unique endeavour has been made possible by financial support from the US Atomic Energy Commission, the University of the Witwatersrand and the Chamber of Mines of South Africa, as well as by the cooperation of the management and men of ERPM.

By Mike Stanley

This is a case study of an opencast coal mining operation where the physical and financial performance was improved via applying a process of transformational leadership development. [ ]

Jan 1, 2008

By J. W. Klokow, S. L. Mulder

Early removal of the shaft reef is usually considered necessary on deep level South African gold mines to avoid damaging stress build-up associated with traditional shaft-protection pillars. In the case of the relatively shallow Beatrix Gold Mine it was largely motivated by early access to ore and the consequent earlier return on invested capital. A number of options were considered to protect the shaft from possible damaging stress changes and to minimise deformations in the shaft-reef area. Numerical modelling was used to evaluate the options and to quantify as accurately as possible the likely deformations to be accommodated by the shaft steelwork designs. The option chosen was a combination of strategically placed satellite pillars and yield pillars, and backfill. Following the mining of a small inner cut during the shaft sinking process, full-scale mining is progressing away from the shaft. Suitable instrumentation has been installed to monitor deformations associated with the shaft reef removal. Enlever rapidement le filon du puits est en général considéré nécessaire dans les galeries de fond des mines d’or sud-africaines pour éviter l’accumulation nuisible de contraintes associée aux piliers de protection de puits traditionnels. Dans le cas de la mine d’or Beatrix, relativement peu profonde, l’enlèvement était motivé en grande partie par l’accès rapide au minerai et par conséquent un profit plus rapide sur l’investissement. Un certain nombre d’options furent considérées pour protéger le puits contre les changements de contraintes potentiellement nuisibles, et pour minimiser la déformation dans l’aire puits/filon. La modélisation numérique fut utilisée pour évaluer les options et pour quantifier aussi précisément que possible les déformations probables que la conceptualisation du puits devrait prendre en compte. L’option choisie fut une combinaison de piliers satellites placés à des points stratégiques avec des piliers de protection, et terre de remblayage. Pendant le fonçage de puits une petite coupure intérieure fut exploitée, et maintenant l’exploitation à grande échelle, au-delà du puits, est en cours. Les instruments nécessaires ont été installés pour surveiller les déformations associées à l’enlèvement du filon du puits. Die frühe Entfernung des Riffschachtes wird normalerweise bei südafrikanischen Tiefbaugoldmienen als notwendig erachtet um den zerstörende Druckaufbau zu vermeiden, welcher mit traditionellen Schachtschutzpfeilern verbunden ist. Im Fall der verhältnismäßig flachen Beatrix Goldmine war es hauptsächlich vom frühen Zugang zum Erz und dem konsequenten frühen Rückfluß des investierten Kapitals motiviert. Eine Anzahl an Optionen wurde erachtet um den Schacht vor möglichen zerstörenden Druckänderungen zu schützen und Deformationen im Riffschachtbereich zu minimieren. Um die Optionen zu bewerten und mögliche Deformationen so genau wie nur möglich quantitativ darzustellen die von den Schachtstahlkonstruktionen aufgenommen werden müssen, wurden numerische Modelle verwendet. Die gewählte Option war eine Kombination aus strategisch plazierten exzentrischen Pfeilern und Schutzpfeilern sowie Hinterfüllungen. Nach dem Vortrieb eines kleinen inneren Einbruches während des Abteufens wird der Vollvortrieb vom Schacht weg vorgenommen. Um die Deformationen, die mit der Riffschachtentfernung verbunden sind zu überwachen, müssen geeignete Instrumentenausrüstungen installiert werden.

Jan 1, 2003

A theory is presented providing a concise mathematical description of the performance of a percussive rockdrill in terms of its principal mechanical dimensions. The theory defines the relationships between the values of thrust required to produce optimum rates of penetration at different throttle air pressures in terms of the piston areas and derives an equation for the prediction of these rates. An analysis of drillsteel life and bit wear is also made.

By J. D. Austin

"Mining Projects: Evaluation, Finance, and Management" held in May 1980 rounded off a theme started with the colloquium on "Exploration Feasibility Studies and Investment Analysis" held in 1979. Seven papers on various aspects of the potential path of an ore-body from an exploration concept through to discovery, evaluation, and financing, to the management of the construction phase, were presented to the 300 delegates at the colloquium held at the National Institute for Metallurgy.

Jan 1, 1980

By G. P. Schoonraad, J. E. Clay

Treatment of zinc silicates by the Waelz Process by J. E. CLAY (M.I.M.M.) (Visitor) and G. P. SCHOONRAAD. Pr. Eng.. B.Sc. Eng. (Rand) (Member) A review is given of the Waelz process. The chemistry of the process and the mechanism of crust formation (accretions) are briefly dealt with. The plant of Kiln Products Limited and its operation are described. The problems encountered and methods for their elimination are presented.

Jan 8, 1976

By R. G. Jurd

This paper considers the introduction of large-scale longwall mining into South African coal mining, instead of the conventional mechanized bord-and-plllar mining that is widely practised at present. The two methods are compared, and longwall mining is found to have the advantage in several respects in some seams. The most cogent reasons for the introduction of the longwall method In some seams are associated with safety strata control and increased labour costs.

Jan 1, 1978

By Gernot Beer, Christian Dünser, Marcos Noronha

The main findings of the joint research initiative “Numerical Simulation in Tunnelling” and a follow-on project on efficient numerical simulation models for tunnelling are presented. Die wichtigsten Resultate des Forschungsschwerpunkts „Numerische Simulation im Tunnelbau“ und einem Folgeprojekt über effiziente numerische Simulationsmethoden werden präsentiert Les résultats les plus importants du point principal de la recherche "simulation numérique dans la construction de tunnels" et un projet consécutif sur des méthodes de simulation numériques efficaces sont présentés

Jan 1, 2003

I am a partner in a minerals' development company called A.B.F. Limited, that does minerals development in Africa and Asia. I have read your very fine magazine often at the Colorado School of Mines Library in Golden, Colorado. I would like to ask your assistance in trying to locate a South African smelter; preferably on the coast, but not totally necessary for the project, that can separate the first four metals (Au, Ag, Cu, and Pb).

Jan 1, 1980

NOTICES The Institution of Mining and Metallurgy The Institution is to hold a one day meeting entitled "Sampling in the mineral and metallurgical processing industries" at Imperial College, London, on 2nd July, 1973. International Conference on Air Pollution This Conference is organised by the Department of Health and the National Association for clean air. Consas 74 The Fifth Conference of Southern African Surveyorswill be held in Salisbury, Rhodesia, from 3rd to 9th February, 1974.

By P. Greenfield

The German steelmaking industry has come up with a novel solution to the problem of waste plastics-grind them into particles and use them in the steelmaking process. Plastics make ideal agents for removing oxygen from iron ore in blast furnaces, and save on oil and coal as well. The aim of replacing heavy oil and coal with plastics in blast furnaces is to use them as reducing agents as well as an additional energy source.

Jan 1, 1996

By R. D. Agrawal, M. L. Kapoor

Cementation has been used extensively by chemists and metallurgists as an economical process for the purification and recovery of metals from dilute solutions. The paper deals. firstly. with the thermodynamic aspects of cementation. and. secondly, with the effects of various process variables, such as temperature. stirring speed. initial concentrationof copper ions. pH of the solution, atmosphere, and surface area of the precipitant metal. on the kinetics of the process in the light of the rate expressions.

Jan 1, 1982

By M. A. von Below

Environmental activists have targeted the mining industry in an attempt to prevent development, which has resulted in the industry's becoming defensive and retro-active. This paper argues that mining managements should go on the offensive and champion the environment through leadership in environmental policy and research and development, rather than reacting to anti-mining campaigns. In the formulation of an environmental policy for the mining industry, a clear understanding of the concept of sustainable development is of paramount importance.

Jan 1, 1993

By J. C. Steinhobel

Answers to questions raised at the Symposium on Trackless Mining in Metal Mines Questions by J. O. Steinhobel (1) When rubber-tyred equipment is used for the delivery of stores and items of equipment, how is heavy material-pipes, rails, timber support, ventilation columns, etc.-dealt with? Termination of Membership In accordance with By-Law 7.6.1. of the Constitution of the Institute, the names of the undermentioned members have been removed from the membership register.

Jan 9, 1973