Search Documents

By R. J. Davidson, V. Veronsee

Some of the parameters affecting the elution of gold from freshly loaded activated carbon using pure water as an eluant were studied. The procedure involved pretreatment of the gold-loaded activated carbon with a strong reagent of sodium cyanide and sodium hydroxide, followed by elution of the gold with water. Gold-loaded carbon obtained from three different sources was studied. It was shown that the elution temperature was the most critical parameter, and column operation at I !OCC (gauge pressure of 50 to 100 kPa) is suggested. The effects of variations in the concentration of sodium cyanide required for the pretreatment of loaded carbon and of variations in elution flowrate were also investigated. Both these parameters were found to have only a marginal effect on the efficiency of gold elution. The investigation also indicated that gold-elution rates were affected to a considerable degree by the particle size of the carbon concerned. Higher elution flowrates could be used when carbons of finer particle size were eluted. A modified eluate-collection procedure was also developed during the course of the investigation. Oven-drying of the loaded carbon was shown to have little or no effect on the efficiency of the subsequent gold elution. The calcium and silica contents of the various carbon samples were also determined. It was immediately evident that the calcium content was very considerable in the case of loaded carbons originating from carbon-in-pulp operations. Calcium concentration was particularly high where air agitation had been employed in the carbon-contacting circuit. To some degree, the calcium build-up explains the serious carbon fouling taking place, resulting in a decreased efficiency of gold adsorption. The fouling problem was found to be less severe when mechanical agitation was used. No poisoning by calcium carbonate was observed where the pregnant solution had been acidified before it was contacted with the carbon.

Jan 1, 1979

The following is available free of charge from the Bismuth Institute, rue Brederode 9, B-I000 Brussels, Belgium: The chemical analysis of bismuth. Automatic methods of guiding welding heads along butt joints. Investigations into lamellar tearing. A technical survey of seam tracking methods in welding. Review - Seawater corrosion handbook, by M. Schumacher (editor). New Jersey, Noyes Data Corporation, 1979. New journal February 1979 marked the appearance of a new monthly journal, Lloyd's Shipping Economist. New edition Gasification of coal, a basic study of existing processes and new developments, by H. D. Schilling, B. Bonn, and U. Krauss (edited by W. Peters). Essen (West Germany), Verlag Gltickauf GMBH, 1979. 2nd revised edition. 336 pp. 68DM (approximately R32). In German. South African technikons The six autonomous colleges for advanced technical education in South Africa were established in terms of the Advanced Technical Education Act (Act 40 of 1967). However, since the inception of these colleges, it has become clear that members of the public find the name difficult to use and to remember. Consequently, these colleges, which play such an important role in the community, were not always correctly identified. Die forging The 9th International Conference on Die Forging will be held from Monday, 4th to Saturday 9th May, 1981, in Diisseldorf, Federal Republic of Germany. It is being organized jointly by the Forging Committee of the Verein Deutscher Eisenhiittenleute and the Vereinigung Deutscher Freiformschmieden. High-temperature alloys An International Conference on the Behaviour of High Temperature Alloys in Aggressive Environments will be held in Petten (North-Holland) from 15th to 18th October, 1979. Strategic minerals The National symposium on the availability of strategic minerals, which is being organized by the Institution of Mining and Metallurgy in collaboration with the Fellowship of Engineering, will be held at the London Press Centre, New Street Square, London EC4, on 20th and 21st November, 1979. The symposium has as its main objective consideration of those minerals that may pose problems of availability in the United Kingdom. Underwater mining The 10th Annual Underwater Mining Institute is scheduled for 1st to 3rd October, 1979, at Galveston, Texas. The Institute will be cosponsored by the Sea Grant College Programs of the University of Wisconsin and Texas A & M University and by the Marine Science Institute of the University of Texas it is being held in co-operation with the Association for Marine Mining. Die Suid-Afrikaanse Instituut Vir Mynbou En Metallurgie - Inligting Oor Lidmaatskap.

Jan 1, 1979

By G. T. van Rooyen

Materials for Winding Plant Components By Prof. G. T. van Rooyen (ScD) (MIT). Materials for critical applications such as winding plant components are reviewed in terms of the basic requirements which have to be complied with. It is shown that tensile testing alone is not sufficient and that impact testing also is necessary if the incidence of brittle fracture is to be avoided. As a criterion it is suggested that the brittle transition temperature (B.T.T.) determined by impact testing should in all cases be well below the lowest anticipated service temperature. A number of steels were evaluated by impact testing and it is shown that a small ferrite grain size, obtained either by chemical means such as by the use of appropriate alloying elements in the steel or by means of a quenching heat treatment, is effective in attaining a Iow B.T.T. The speed of strain aging as well as the influence of strain aging on the B.T.T. was also evaluated. On the basis of the results obtained it is recommended that steels for critical applications must conform to an appropriate grade and class of steel according to BS 4360 specification. It is further recommended that such steels be exempted from the customary six-monthly heat treatment prescribed by the Mines and Work Act, Regulation 16,18.

By Arvi Parbo

I would like to use the occasion to reflect on how the world environment for the minerals industry is undergoing substantial change, and how this change may affect the industry. I have given my talk the title 'The Quest For Competitive Edge', because the net effect of the changes taking place is that competition is increasing. To set the scene, let us look back at the situation which has existed in our industry in the past.

Jan 1, 1993

Professor Miklos Salamon, Research Adviser to the Chamber of Mines of South Africa, has won the Rock Mechanics Award for 1983 of the American Institute of Mining, Metallurgical and Petroleum Engineers 'for applications of analysis to many varied practical mine design problems’. Mintek reports Report M119 A versatile computer programme for data capture in multi-element analysis by a sequential X-ray spectrometer. Report M120 South African costs of equipment for the metallurgical industry (1983). Report M125 Commissioning of an automated microphotometer used in spark-source mass spectrometry.

Jan 1, 1984

A 36-year-old A-S-H pump, manufactured to designs dating back to 1936, was recently presented to the Gold Mine Museum by Envirotech. The pump, a B-frame three-piece rubber-lined Hydroseal unit, was supplied by Envirotech's predecessor company, Denver Machinery, and was installed by South Roodepoort Main Reef Areas Limited on 22nd March, 1948. Metals, materials, manufacturing The 37th Annual Conference of the Australasian Institute of Metals will be held in Ballarat (Australia) from 13th to 17th May, 1985. 1985is the Sesquicentennial year of Victoria, and for the first time the historic City of Ballarat has been chosen as the venue for an Australasian Institute of Metals congress. Steel rolling Conferences on steel rolling, sponsored by The Iron and Steel Institute of Japan (ISH), and supported by iron and steel institutes in many countries of the world, have been held since 1980. The first conference was held in Tokyo in 1980, sponsored by The Iron and Steel Institute of Japan.

Jan 1, 1984

The Centenary Luncheon for Past Presidents was held on Thursday, 24 March, 1994 at The President's Room at Gold Reef City, Johannesburg at 12:30. Herewith the proceedings that followed. Dr H. Scot-Russell It is with great pleasure that my fellow Office Bearers and I welcome you, our Past Presidents, to this luncheon to mark the centenary of the SAIMM. Today one hundred years ago, a group of professionals met and agreed to draw up the constitution and by-laws of a society later to be called an Institute. The Presidents of the Institute, of course, become its Past Presidents and help to guide its progress. A number of our sister institutes cannot wait for their Past Presidents to move of their councils, and cannot understand how we can give such free reign to ours! We believe it one of our strengths. The successful cooperation between our Past Presidents and ourselves is due to the personalities of these men. They attend meetings not to ensure that the status quo is maintained, but allow the current Office Bearers freedom to lead the Institute as they think fit. But they are always present to give sound advice, a helping hand, and support to the Institute in every way.

Jan 1, 1994

VERSLAG- REPORT No. 1365 STUDIES OF INCIPIENT FUSION IN THE SYSTEM CHROMITE- MgO- Al2O3-SiO2-C 5th January, 1972 Investigator: N. A. Barcza SYNOPSIS A fundamental study was made of twelve chromite ores by use of a thermobalance under atmospheric and reducing conditions. It was found that their thermal behaviour under atmospheric conditions can be related to the mineralogical composition of the chromite spinel and the gangue. The overall mechanism of reduction with solid carbon over the temperature range of 1 200 to 1 500°C was shown to be diffusion of carbon through the reaction product. The effects of additions of fluxes and variations in particle size on the kinetics and mechanism of reduction were determined. It was shown that carbon monoxide does not reduce chromite ore up to temperatures of 1 550 °C, and it can therefore be eliminated as the diffusing reducing species. However, the reaction product of reduction, namely a mixed carbide of iron and chromium, was shown to be an effective reducing agent for chromitc ore, while also facilitating the transport of carbon. VERSLAG - REPORT No. 1380 AN ELECTROCHEMICAL MODEL FOR THE LEACHING OF URANIUM DIOXIDE 10th January, 1972 Investigators: C. R. S. Needes, M. J. Nicol SYNOPSIS A correlation between the rate of leaching of UO2 and the electrochemical properties of the oxidant concerned has been derived. This correlation is found to be borne out by experimental results. Certain effects observed in UO2 leaching and hitherto unexplained have been clarified in terms of an electrochemical mechanism. Experiments have shown that the mixed potential of a UO2 electrode gives a measure of the rate of dissolution of UO2. Its significance to commercial practice is discussed. CONCLUSIONS (I) The dissolution of UO2 in the presence of a number of oxidants can be explained in terms of an electrochemical mechanism. (2) The mixed potential of the UO2 electrode is a measure of the rate of UO2 leaching. This principle could be used in the control of industrial leaching operations. (3) A simple treatment has provided a mathematical basis for a fundamental correlation between the rate of U02 dissolution and the chemical properties of the oxidants concerned. This relation has been found to agree well with experimental results. (4) A number of phenomena occurring during the leaching of UO2, hitherto not explained in a satisfactory manner, have now been clarified in terms of an electrochemical mechanism.

By W. J. Vlasblom, A. M. Talmon, A. J. Nobel

In initial laboratory tests with a travelling submerged jet on artificially prepared clay it was found that the cavity depth is dependent on the stagnation pressure of the jet and the undrained shear strength of the clay. In addition, it has been observed that the increase in cavity depth with jet pressure is stronger at higher jet pressures. It is assumed that this can be explained by cavitation of the jet at higher jet pressures. At cavitation a cone of bubbles is formed around the jet, which reduces the exchange of momentum between the jet and the surrounding water. This results in a higher jet velocity and a higher stagnation pressure at a specified distance from the nozzle exit. In literature, no relation between the jet pressure of a free submerged cavitating jet and stagnation pressures was found. Additional tests were carried out to determine this relationship. Because practical dredging occurs at relatively large water depths, these tests were performed in a pressure vessel at different pressure levels. It is concluded that the efficiency of a jet (defined as the stagnation pressure at a certain distance divided by the jet pressure), for stand-off-distances smaller than 45 times the nozzle diameter, increases significantly by cavitation in comparison to the non-cavitating situation. However, the jet pressure required for a fully developed cavitation cone increases strongly with water depth. At dredging depths of 20 m and more, the necessary jet pressures are higher than normally applied in dredging practice. Thus in spite of the importance of cavitation in laboratory tests at atmospheric pressure, in normal dredging practice cavitation is of less importance.

Jan 1, 2007

By P. G. Van Der Walt

This paper deals with the reticulation of deslimed tailings from surface to the stope face underground. Reference is made to the experience gained at the pilot plants operating on four of the gold mines administered by Gold Fields of South Africa, as well as at the full-scale system at East Driefontein which was commissioned recently. Mine-wide backfill systems are currently being installed on five other mines administered by Gold Fields. These six full-scale systems are capable of handling more than 270 000 tons of backfill solids per month. The type of reticulation system chosen, the selection of flowrates and the composition of the slurry, as well as the selection of the appropriate pipes and ancillary equipment are discussed. Both theoretical and practical aspects are taken into consideration. Other aspects covered include the design of underground storage dams and communication systems.

Jan 1, 1988

By J. W. van der Merwe, C Strydom, D. C. Odendaal, M. I. Sampson

Keywords: Sphalerite, Bio leaching, Chemical leaching Sphalerite concentrates were prepared from tailings dam samples obtained from Rosh Pinah Mine in Namibia. The samples were subjected to froth flotation and concentrates containing between 7% and 14% Zn were prepared. Leaching of these froth flotation concentrates were studied in ferric chloride solutions at different Fe3+ concentrations for different times at different temperatures with the influence of other species on the kinetics in mind. Complementary to this research, GeoBiotics, LLC and Exxaro Resources have developed proprietary bioleaching technology for the oxidation of base metals concentrates using GEOCOAT bio heap leaching technology in a sulphate medium. The ferric chloride laboratory work was performed in a fluidising leach reactor. The studied material was obtained from flotation concentrate produced during an investigation into the recoverability of a tailings pile at Rosh Pinah mine in Namibia. The optimum conditions for the laboratory investigation were found to be a Fe3+ concentration of 0.3 mol/dm3 at 80°C. A control was performed by using synthetic zinc sulphide. GEOCOAT evaluation tests are performed for the purpose of evaluating the bioleaching of ore and flotation concentrates by means of mesophilic bacteria, Column tests were carried out on the flotation scavenger concentrate from Rosh Pinah to assess the application of the GEOCOAT® process for the oxidation of a low grade zinc concentrate. In this study an attempt was made to demonstrate the relationship between the Kinetic models and the experimental data by plotting the fraction of Zinc leached against time and applying the different equations to the data. The kinetic models were applied to the data obtained from both the test regimes. Habashi (1999) proposed that if a process is controlled by a chemical reaction at the interface (phase boundary controlled reaction), the following equation applies. kCt =1 ? (1-R) 1/3 Alternatively a process is controlled by diffusion through the product layer the following equation applies: [kt = 1 23- X (1 ? X) 2/3] As the anodic dissolution reaction progresses, reaction product forms either a more or less dense reaction product layer on surface As this product layer forms, a diffusion problem develops governed by the nature of the product layer. The conclusion from the study was that the kinetics is very dependent on the type of ore processed relating to the mineral composition of the ore body.

Jan 1, 2007

By R. Pretorius, N. Mautsa

In a cobalt precipitation plant, phosphoric acid is used to eliminate excess uranium from the pregnant leach solution, resulting in a cobalt hydroxide product that has little uranium contamination. However, the amount of phosphoric acid added must be monitored and controlled to avoid financial and sustainability impacts and to prevent negative impacts on the final product quality. One possible solution to this problem is the use of online residual phosphorus measurement techniques to regulate the addition. By continuously monitoring the residual phosphorus levels in the solution, the plant can adjust dosing in real time to maintain the target residual phosphorus level. As a result, the cobalt precipitation plant can improve phosphorus level control, lowering the risk of overdosing, and ensuring consistent product quality. This approach can also improve process efficiency, reduce operational costs, and have a positive environmental impact

Jan 1, 2023

By P. Horrell, K. Rhodes, G. Harrison, J. Dean, D. Sammons, M. Stander

Anglo Platinum have perceived a need to increase the rate of reef development both for new mechanised stoping technology and on conventional new developing mines. The Research and Development Division of Anglo Platinum therefore initiated an experimental reef raise project with a tunnel boring machine (TBM) at Bafokeng Rasimone Platinum Mine (BRPM). The scope of the trial was for the boring of a reef raise 340 metres in length on the Merensky Reef. The boring phase of the trial took place over six months and the average rate of penetration of the TBM was 0,47 metres/hour. TBM utilisation was 22%. The TBM used in the trial was a Jarva MK6 manufactured in 1972 and its design with its backup system was not considered to be an ideal machine for reef development. However it was the intention of the trial to prove the concept of developing with a TBM on reef. In this respect the trial was unequivocally a success. There were many problems and long delays did occur during the boring phase. Nevertheless there is every confidence that a new TBM can be designed specifically for this type of work that will achieve high rates of advance up to (say) 400metres/month and with a more flexible steering system in order to negotiate reef changes. It can therefore be expected that TBMs will be used in the future for reef development on South African platinum mines.

Sep 1, 2001

By H. Xuchun, H. Nailian, L. Guoqing

With the accession to WTO and the establishment of Shanghai Gold Exchange, gold mines in China are facing more severe competition from both home and abroad. Supply Chain Management (SCM), a new management idea gradually accepted all over the world, provides the gold mines in China with a new management mode. In this thesis, under the guidance of SCM theory, based on the analyzing to the actualities of Jiaojia Gold Mine, the Jiaojia supply chain framework is constructed, the function system for Jiaojia SCM is configured, and function modules are described in detail. Keywords: Supply Chain Management, Gold mine, Informatization

Jan 1, 2003

By Nicolle Krusberski

Potential errors in XRF analysis are discussed and investigated with specific reference to the analysis of ilmenite samples. A selection of ilmenite samples was chosen and prepared using two XRF preparation techniques: pressed powder pellet and unroasted fusion bead. The merits of the two methods have been discussed in this paper for ilmenite analysis by XRF. Recommendations have been made regarding the use of pressed powder pellets especially with regard to the mineralogical effects that were evidenced during this investigation. The fusion bead technique was found to be far more accurate and able to meet short turnaround requirements provided the calibration methodology used is specific to the grade of samples analyzed.

Jan 1, 2014

By R. G. Koelmans

In 2001 Platinum overtook gold in foreign revenue earnings for South Africa. The export sales from platinum group metals amounted to R29.3 billion as opposed to gold export sales of R28.6billion1. Organizations must undertake new ventures to replace old, worn-out and obsolete assets with new ones. These assets could be a building, a new product or process, a new mine, or anything that can help the organization to achieve its objective. These ventures are projects by their nature. When a project is pronounced a success, the judgement is usually based on some factual evidence, although not every one uses the same data. From the literature, it is obvious that there is a lack of consensus and objectivity as to what constitutes a successful project. The purpose of this paper is to address the following questions: ?What constitutes a successful project? ? How does one measure project success? ?How can one work toward project success? This paper addresses the requirements for project success of three of the primary stakeholders of a project, namely the business or client, the employees as far as the project team is concerned, and the local community. Indicators are developed into a work breakdown structure (WBS)-like chart to demonstrate success indicators. These indices take cognisance of all the constituents required for project success. The indicators are further developed to take cognisance of the requirements of the local communities. These indices are then weighted to arrive at a total score for the respective stakeholders. Using these WBS models, the success and performance of a project can be evaluated. This score is considered an objective measure of project success. Projects are evaluated more consistently across different projects and the project manager is provided with a management tool that can assist him/her in ensuring greater project success. The shortcoming of this approach is that the weights of the different indices have been estimated at this stage. Research will have to be conducted to more accurately reflect the weights assigned to the indices.

Jan 1, 2004

COUNCIL AND STANDING COMMITTEES, 1974-1975 Office Bearers : Prof. R. P. Plewman (President), Dr R. E. Robinson and Dr M. D. G. Salamon (Vice Presidents), J. K. E. Douglas (Honorary Treasurer), and P. W. J. van Rensburg (Immediate Past President). Elected Members of Council: Dr M. G. Atmore, E. Collier, G. H. Grange, Dr P. R. Jochens, Dr D. I. Legge, D. G. Malan, C. T. Shaw, L. W. P. van den Bosch, D. A. Viljoen, H. M. Wells, P. A. von Wielligh. Branch Chairmen: B. T. Hosking (Witbank-Middelburg Branch), D. A. Smith (Orange Free State Branch). Past Presidents Serving on Council: R. J. Adamson, M. Barcza (until May 1975), H. Britten, H. E. Cross, Prof. J. de V. Lambrechts (until December 1974), R. C. J. Goode, Prof. D. D. Howat, Dr J. P. Hugo, D. M. Jamieson, D. G. Maxwell, Dr J. T. McIntyre, V. C. Robinson. Ten Council meetings were held during the year, with an average attendance of 19, and the standing and sub-committees held 74 meetings. COMMITTEE CHAIRMEN Membership, Dr M. D. G. Salamon; Technical Programme-Metallurgy, D. A. Viljoen; Technical Programme-Mining, G. H. Grange ; Vacation School-Metallurgy, Dr P. R. Jochens; Vacation School-Mining, Dr M. D. G. Salamon; Awards, Prof. R. P. Plewman; Excursions, Dr D. I. Legge; Constitution, Rules and Policy, P. W. J. van Rensburg and Prof. R. P. Plewman; Mines and Works, P. A. von Wielligh; Education, P. W. J. van Rensburg. REPRESENTATIVES ON OTHER BODIES Associated Scientific and Technical Societies Members: V. C. Robinson and Prof. R. P. Plewman. Alternates : Dr R. E. Robinson and Dr M. D. G. Salamon. Federation of Societies of Professional Engineers Members : J. K. E. Douglas and P. W. J. van Rensburg. Alternates : Prof. R. P. Plewman and G. H. Grange. South African Council for Professional Engineers Member : R. C. J. Goode. Alternate : G. H. Grange. Engineers' Liaison Committee (Pretoria) Member: Dr J. P. Hugo. Alternate: P. W. J. van Rensburg. MEMBERSHIP Thirteen Fellows, seventeen Members, eleven Graduates, three Associate Members, eighteen Associ¬ates, twenty-six Students, and one Company Affiliate were elected during the year. Nine Fellows, four Members, and three Associates were admitted to retired membership. Eight Fellows were elected to Honorary Life Membership. Three Members and one Graduate were transferred to Fellows, nine Graduates and two Students to Members, six Students to Graduates, one Student to Associate, and one Associate to Associate Member. Six Fellows, ten Members, three Associates, and one Student resigned. A statement of membership as at June 30th 1975 and the end of the previous year is shown in the following tabulation: 30th - 30th June, - June, 1974 - 1975 Honorary Life Fellows - 9 - 15 Honorary Fellows 8 - 8 Life Fellows 170 - 170 Fellows 544 - 536 Members 512 - 523 Associate Members 10 -15 Graduates 130 - 133 Associates 194 - 210 Students 173 -175 Company Affiliates 70 - 71 1 820 - 1 851 [ ] OBITUARIES Your Council records with deep regret the death during the year of the following members: M. Barcza, Honorary Life Fellow and Past President of the Institute; J. A. Boyd, F. E. Keep and J. H. Taylor, Life Fellows; I. D. B. Corner, C. O'G. Deane, R. E. Gilmour, A. C. Hofmeyr, M. W. Howell, T. J. Robin and F. C. Steinhobel, Fellows; J. J. Frankel, Member; T. J. Higgs, Associate. FINANCE The annual accounts, which follow this report, indicate that income again exceeded expenditure by a margin of R21 410 (last year R28 524). This year's income of R71 184 showed a further increase compared with last year's figure of R55 025. Costs, however, also in¬creased, and it is calculated that, excluding non-recurrent costs, the cost of running the Institute in¬creased by R6 654 from R25 501 to R33 155 for the current year. The main increases were involved in secretarial fees, stationery and print¬ing, and in publication of the Journal. All indications are that costs will continue to rise, and we have been advised that the A.S. & T.S. will be increasing their secretarial fees by 25 per cent in the year ahead to meet their rising costs. This year's surplus was derived entirely from the revenue from sales of publications (R13 644) and a surplus from the 1974 Winter School (RIO 654). There can be no certainty that revenue from these sources can be repeated each year. Our funds are in a satisfactory position because of these worth¬while activities, but the administrat¬ion of the Institute should not de¬pend on them. Council will accord¬ingly have to give consideration in the year ahead to an upward adjust¬ment of subscriptions to meet rising costs.

Jan 10, 1975

By P. Wiesner, H. –M. Stonner

A brief account is given of the influence of sulphuric acid and chloride ions during the recovery of uranium by solvent extraction, followed by a discussion of the settling behaviour of dispersions and models to represent that behaviour. The paper ends with a description of various methods for the recovery of solvent, which is lost in the solvent-extraction process by entrainment and adsorption on solids and by dissolution.

Jan 1, 1982

By G. R. Sawyer

Although backfilling has been in operation for many years, the methods for selecting appropriate slurry dewatering aids have, in some cases, been rather unsophisticated. This has led to many misconceptions regarding the role of the dewatering aid and its various means of application. Testing procedures employed in the correct selection of any practically applied dewatering aid must mirror the actual working processes in which they are to be used. This constraint necessitates the development of complex testing methods when applied to backfilling. The current testing procedures were scrutinized and their various merits noted. From this study a series of testing methods was evolved which incorporate the best aspects of these testing procedures with novel ideas which would eventually result in the correct selection of the dewatering aid. A major consideration in the application of any of these methods is the modus operandi of the backfilling process, and the relevance of the tests to the process. This work attempts to consolidate the testwork performed in the past and suggest new approaches in the correct selection of acceptable dewatering aids for backfilling.

Jan 1, 1988

Anglo Platinum is in the process of introducing a number of initiatives, varied in nature, on a scale that will impact operations in the short, medium and long-term. The advent of mechanization on a large scale and the introduction of new mining technologies therefore require a different approach to the design of ventilation and cooling systems. In addition, the ventilation and cooling systems serving increasingly deeper operations will place a greater demand on electrical power consumption?this in an environment where power generation is limited and increasingly expensive. Ventilation and cooling systems currently being employed in platinum operations have evolved from practices first pioneered in deep level gold mines. However, in modern and future platinum mines, deepening of operations will take place in a somewhat different environment?particularly in terms of geothermal settings and electrical power utilization. This provides the opportunities to devise novel and energy-efficient ventilation and cooling strategies tailor-made to meet these challenges. The need for refrigeration and cooling at depth will increase the capital and operational cost component of ventilation systems and the medium-term limitations on the availability of electrical power will require the provision of innovative systems. The increased use of diesel-powered vehicles underground, the viability of energy recovery and feasibility of thermal storage opportunities are discussed in this paper. Some of the challenges and the solutions currently proposed in terms of ventilation system design, refrigeration plant selection and chilled water distribution methodologies are described. Changes in strategies core to this discipline that affect the health and safety of employees and the profitability of modern operations are deemed necessary to support the transformations that are envisaged.

Jan 1, 2008