Search Documents

By B. S. Xakalashe, M. I. Khama, Q. G. Reynolds

The carbonaceous reduction of manganese ore is an energy-intensive process that releases large amounts of pollutant gases. In an attempt to circumvent the greenhouse gas emissions, this research investigates hydrogen as an alternative reductant. The reduction of manganese ore with hydrogen results in the structural changes in the intermediate products, which might limit the diffusion of the reactant gases through the pores. Computational fluid dynamics (CFD) models capture the structural changes and predict the rate controlling mechanism and this is key in designing the prereduction reactors. The current work uses CFD models to predict the degree of reduction in a shaft furnace under hydrogen reducing conditions. Manganese ore is described as a collection of scalar and tensor fields such as thermal conductivity of the porous medium, density, and viscous resistance. The results indicate that advection contributes significantly towards the overall transport of hydrogen to the reaction sites. Porosity of the final product was found to be higher than porosity of the raw material.

Mar 4, 2025

By N. V. Moraka

Mining companies are required by law to improve representation of women on their boards. However, progress in this regard has been slow. Boards of directors play an important role in formulating corporate strategy, risk assessment, and effective governance for sustained financial performance. Although some women have successfully maintained board seats, others have been unable to do so. It is difficult to ascertain whether women are being appointed as tokens to satisfy social pressures, as little is known about the experiences of women board members in mining, which may inform or refute tokenism. In-depth interviews were conducted with 20 women and 16 men across six listed mining companies. Thematic data analysis revealed evidence of tokenism where recruitment to mining boards is compliance-based and is informally driven by influential directors. Adverse boardroom experiences that further confirmed tokenism were reported by women, such as disregarding their contributions, condescending behaviour, and limited influence in decision-making, while other women sought to validate their competence and oppose social exclusion. This study recommends that a strong Board Chair and nominations committee is critical to ensure sustainable recruitment of competent and suitably qualified women; and further foster a culture of inclusivity and valuing gender-diverse boards.

Dec 13, 2023

The relationship between the aspect ratio and physical fields in aluminium reduction cells wase studied numerically. The aspect ratio was firstly defined and 7 kinds of 320 kA cells with different aspect ratios were put forward. By using numerical simulation, the relationship between the aspect ratio and the electric-magnetic flow fields, magnetohydrodynamic stabilities, and thermal stability was discussed. It is concluded that the electric-magnetic flow field distributions are greatly affected by the aspect ratio. From the perspective of magnetohydrodynamics stability, the larger the aspect ratio is, the more stable the cell will be. A larger aspect ratio is more beneficial for the thermal stability under the same current density.

Jan 1, 2011

By M. Timucin

High-temperature phase relations in the Pb-PbS system were established by the quenching of samples equilibrated in evacuated and sealed silica capsules. The liquid-miscibility gap seen in some previously published phase diagrams was not observed. The thermodynamic activities of PbS in liquid solutions of this system were derived at 1473 K from the isopiestic equilibration of samples belonging to this solution series with Cu2S-PbS melts of known PbS activities. The behaviour of Pb-PbS melts was found to be compatible with a subregular solution model. This model also made it possible to obtain an analytical liquidus for PbS that was in excelent agreement with the experimental determination.

Jan 1, 1988

By G. J. McDougall, M. J. Nicol, O. L. Wellington, R. G. Copperthwaites, R. D. Hancock

X-ray photoelectron spectroscopy showed that the adsorption of gold cyanide on carbon in the presence or absence of electrolytes and acids proceeds by the same mechanism. Although the identity of the gold cyanide adsorbate is not known, the mechanism appears to have an initial adsorption stage that involves the adsorption of an ion pair: Mn+[Au(CN)-2]n where Mn+ is a metal ion (for example Na+, K+ and Ca2+) that has a lower solubility than the Au(CN)-2 anion in the adsorption medium, followed by a reduction step in which either a sub-stoichiometric Au(CN)x surface species or a cluster-type compound of gold is formed.

Jan 1, 1980

By C. Liu, F. Ye

"To extend the variety of lump ores that are used in the COREX shaft furnace and to optimize iron ore blending, the original evaluation method for iron ores that was proposed by Voestalpine AG has been improved. Physicochemical and metallurgical properties of iron ores, including Sishen lump ore and CVRD pellets, which are currently used in the COREX process, and three other lump ores, were assessed and compared. Ore matching principles were proposed and five optimized iron ore blending schemes designed and verified by laboratory experiments to prove the effectiveness of the improved evaluation method. The replacement of Sishen lump ore by the alternative L2 and L3 lump ores without varying the proportion of CVRD pellets could improve the degree of reduction and rate of metallization, and decrease the bonding index. Based on the results of laboratory test work and industrial- trials, an ore blending scheme of 60% CVRD, 20% L2, and 20% L3 is recommended for use in the COREX process. IntroductionIn recent years, problems such as environmental pollution and a shortage of coke and coal resources for blast-furnace ironmaking have become increasingly apparent. Based on sustainable developments in the iron- and steelmaking industries, the environmentally friendly COREX smelting-reduction process with low energy consumption was developed and introduced (Zhou and Du, 2013; Song, Lv, and Yin, 2015; Xu et al., 2016; Kurunov, 2010). The evaluation system for lump ore that was proposed by Voestalpine AG recommends that only Sishen lump ore from South Africa be used in the COREX process, because of the stringent physicochemical and metallurgical property requirements. This situation significantly hampers improvements to the technical and economic aspects of the COREX ironmaking process, especially in China (Eberle, Siuka, and Bohm, 2006). No theoretical or technical basis has been provided for the evaluation system, and the assessment approach for iron ores also presents problems that need to be discussed and resolved.The COREX process consists of two reactors: the prereduction shaft furnace and the melting gasifier as shown in Figure 1 (Wu et al., 2017). Pellets and lump ores which are charged to the prereduction shaft should have a good reducibility and metallization with a low degradation index (Li et al., 2016; Wu et al., 2011; Kumar et al., 2009; Kang, Gupta, and Sahajwalla, 2007). The properties and microstructure of the iron ore pellets which are required to achieve a high productivity and a lower fuel rate in the COREX process have been investigated (Umadevi et al., 2011). Some efforts have also been made to investigate the behaviour of lump ores in the COREX shaft furnace, including the disintegration characteristics and the reduction degradation (Umadevi et al., 2011; Zhou et al., 2015; Xu et al., 2013; Li, Feng, and Zou, 2013; Hou et al., 2014). However, few studies have focused on the optimization of ore blending for partial or total substitution of the expensive Sishen lump ore by other, cheaper lump ores to reduce the production cost. The technology for the utilization of blended lump ores in the COREX process is still in its early development stages (Zhou et al., 2017; You et al., 2017)."

May 1, 2019

By C. H. Wyndham, N. B. Strydom

Discussion C. G. Hinds (Member): The climatic chamber at Kloof Gold Mine was built to the design referred to in the paper presented by Professor Wyndham and Dr Strydom. As no suitable underground facilities existed for the acclimatization of labourers at the rate required, mining operations would have been severely restricted had there not been a climatic room timeously built on surface. The climatic room can accommodate 120 labourers per 4-!-hour shift. The standards laid down by the Human Sciences Laboratory were and still are being adhered to as strictly as possible. Through a shortage of European personnel the recommended degree of white supervision could not be adhered to and the use of Bantu assistants with a minimum education of Standard 8 was introduced. This is considered to have met with sufficient success to warrant acceptance as policy. The climatic room was brought into operation on the 1st September, 1967, i.e. two months after stoping at Kloof was commenced. The figures quoted herein therefore pertain to the period between that date and the 31st March, 1969, when the main shaft and the main surface fans were commissioned. The areas worked were sited between 5016 ft and 6 365 ft below surface. Virgin rock temperatures ranged between 92°F and 99°F. Stopes are cleaned by hand lashing. During the 20 months of stoping prior to the commissioning of the main shaft, mining operations at Kloof were effected through the Harvie Watt shaft of the Libanon Gold Mining Company Limited. In this period 10 452 Bantu labourers were acclimatized in the following categories: Experienced workers 7 326 New to the industry 2 086 Re-acclimatized 1 040 It will be noted that during the period, labourers 'new to the industry' averaged 22 per cent of the intake. This percentage fluctuated from time to time and reached 42 per cent. (The present percentage is 60.) The greatest number acclimatized during anyone month occurred in February, 1969 when 1234 Bantu were treated. The greatest number of Bantu acclimatized during any 8-day period was 411. As many as four X 41/2 hour shifts were run in 24 hours. The number of men found to be heat intolerant over the period of 20 months was 33 out of a total 9 412 Bantu. The following tabulation illustrates the history of the build-up of manpower and the climatic conditions under which they worked: The average dip of the reef is 35°. The number of heat stroke and heat exhaustion cases during the period of 20 months under most difficult ventilation conditions was Nil.

Jan 10, 1969

By N. Naude, L. S. Leal Filho, M. P. Tshazi

In this paper, the authors performed experiments in the Denver and Leeds laboratory flotation devices at the University of Pretoria at various particle sizes to evaluate the performance of the devices. Quartz was used in a single mineral system at discrete sizes fractions, -25 μm, +25- 45 μm, +45-75 μm, and +75-106 μm. Hydrodynamic analysis, based on dimensionless power and Reynolds numbers, indicated that the Leeds cell required higher power input to achieve comparable flow conditions. Specifically, the Leeds cell exhibited an average power number of 1.03, whereas the Denver cell averaged 0.77 within the same impeller speed range of 1000 rpm–1500 rpm. For comparative flotation performance, impeller speeds were calibrated, resulting in operating speeds of 1200 rpm for the Denver cell and 1400 rpm for the Leeds cell. The cells performed similarly at two coarser-sized fractions. However, some deviations were observed in the finer particle size range. The -25 μm (fine) fraction initially achieved a recovery of only 15%. An additional reagent dosage was required to enhance the recovery of this fraction significantly. These findings highlighted the influence of particle size on flotation recovery. For all experiments, the Denver laboratory flotation cell outperformed (defined by higher recovery) the Leeds device, while still operating at a lower impeller speed. This advantage can be attributed to its impeller-stator design and air dispersion features, effectively overcoming slurry resistance and resulting in superior flotation performance compared to the Leeds cell.

May 27, 2025

By P. J. Foster

This paper summarizes a behavioural safety project undertaken in seven quarries in the UK in order to investigate its applicability as a means of raising the standards of health and safety in the UK quarrying industry. A behavioural safety methodology was developed and trialed at two quarry sites in the UK. During the study the number of unsafe acts and minor accidents had decreased and at one of the quarries there was a 95% reduction in the number of working days lost. It was then introduced at a further five sites of varying sizes and within this focused specifically on lone workers as well as behaviours that affected quality and environmental issues. Positive improvements were noted in most of these operations. The project also looked at the effectiveness of health and safety performance indicators. Here, the common lead and trailing indicators for both safety and health that are commonly used by industry were identified. In consultation with the UK quarrying industry these were then used to identify specific performance measurement criteria that can be used by the quarrying sector to measure performance. Following on from this, a quarry specific health and safety management system specification was developed for large and small quarries.

Jan 1, 2008

Council and Standing Committees, 1976-1977 President: Dr M. D. G. Salamon. Vice-Presidents: P. A. von Wielligh and Dr M. G. Atmore. Honorary Treasurer: J. K. E. Douglas. Immediate Past President: Dr R. E. Robinson. Members of Council: J. D. Austin, E. Collier, C. T. Fenton, J. A. Holmes, Dr P. R. Jochens, Prof. R. P. King, Dr D. G. Krige, Prof. F. Q. P. Leiding, D. G. Malan, C. T. Shaw, D. A. Viljoen, R. A. von Maltitz. Chairman, Witbank-Middelburg Branch: E. J. Jackson. Chairman, Orange Free StatelKlerksdorp Branch: A. N. Shand. B. Past Presidents Serving on Council: R. J. Adamson, H. Britten, J. K. E. Douglas, R. C. J. Goode, Prof. D. D. Howat, Dr J. P. Hugo, D. G. Maxwell, Prof. R. P. Plewman, V. C. Robinson, P. W. J. van Rensburg. Ten Council meetings were held during the year, and the standing and sub-committees held seventy-one meetings. Standing Committee Chairmen: Membership, Dr M. G. Atmore; Technical Programme - Metallurgy, J. A. Holmes ; Technical Programme - Mining, C. T. Shaw; Vacation School - Metallurgy, Prof. R. P. King ; Vacation School - Mining, Dr D. G. Krige ; Awards, Dr R. E. Robinson; Excursions, C. T. Fenton; Adjudi¬cation, Dr R. E. Robinson; Constitution, Rules and Policy, Dr R. E. Robinson; Mines and Works, C. T. Shaw; Education, Dr R. E. Robinson; Pyrometallurgical Discussion Group (Convenor), Dr J. B. See; Phoenix National Committee, Dr R. E. Robinson.

Jan 1, 1978

By J. H. Bulloch

A study of fatigue-crack growth in a rail steel and an associated weld metal showed that fatigue cracks in the deformed rail steel had slightly higher growth rates than in undeformed rail steel. The crack growth in the weld metal was appreciably faster than either and exhibited plateaux that were above the upper bound reported for rail steels, The cyclic-life curves showed that, over an indicated service period of 8 years, both the deformed and the undeformed rail steels should not be prone to fatigue failures under the defined mechanical conditions, For the weld metal, the cyclic-life curves indicated the possibility of premature fatigue failures but, as al the input parameters represented a 'worst case' situation, this assessment could wel be ultra-conservative. In the rail steels at low levels, the extension of the fatigue cracks occurred by ductile striated growth. At a Kmax level of 35 MPa .J/n, cleavage facets formed initially on the surface of the fatigue fractures, and their incidence increased with Kmax until the onset of fast failure, The microstructure of the deformed rail steel exhibited cleavage facets at a slightly lower Kmaxvalue, and contained more cleavage facets at a given K level, than the microstructure of the undeformed rail steel. The average size of the cleavage facets agreed well with the pearlite nodule dimensions of 60 to 100 ILm. The microstructure of the weld metal was much coarser and contained columnar grains. At al f.K levels, the dominant fracture mode was cleavage, with small isolated regions of ductile striated fatigue cracks. The size of the cleavage facets varied from 150 to 600 ILm, and such a variation may be explained by the fact that cracking generally occurs in association with the pro-eutectoid ferite phase, and that this phase is distributed along some boundaries of prior austenite grains and the boundaries of the coarser columnar grains.

Jan 1, 1987

By A. Becker, R. Tait, S. L. George, A. Carlisle

Surface treatments like laser shock peening (LSP) induce residual stresses penetrating up to 1 mm deep, surpassing traditional methods, thus significantly increasing the potential impact on materials prevalent in the automotive and aerospace sectors. Through extensive fatigue testing and fractography investigations, it was determined that LSP resulted in a fatigue life increase of over five times for aluminium alloy AA7075-T6 and titanium Ti-6Al-4V. Increased fatigue life was also noted in AISI316 stainless steel, which showed increases in fatigue life of 1.7x. While fatigue life in all cases improved, the efficacy of LSP was shown to be material dependent.

Jul 23, 2025

By E. Arghavani, S. H. Amiri, S. Zare, F. Sepehri, M. Ramezanizadeh

Mineral processing plants include different stages like crushing, grinding, classification and concentration, all of which have partially affect the final product. To identify and solve the related problems of each stage, process audition should be carried out continuously to find the major solutions of improving product and decreasing the maintenance and operating costs. The Iranian Gohar-Zamin iron ore beneficiation plant consists of equipment such as gyratory and cone crushers, high pressure grinding rolls (HPGR), ball mill, dry and wet double-deck vibrating screens, hydrocyclones cluster, magnetic drum separators, thickener and horizontal vacuum belt filters. The defects of initial design as well as current non-standard operating conditions of equipment were monitored and detected and the opportunities for process optimisation were presented as follows: establishing the control loop of power draw for cone crushers, the modification of feeding chute in cone crushers to minimise the non-uniform wear of parts, removing segregation in the fresh feed bin and screen’s circulating load chute in order to provide the proper feed to HPGR, reducing wear rate on HPGR rolls surfaces, decreasing the amount of rejected materials in screen, equalising the solid content and particle size distribution (PSD) of feed in all magnetic drum separators and equalising the PSD of hydrocyclones overflow. This paper provides a guideline for the mineral processing industry to focus its efforts on process design to deliver the efficiency with minimum capital costs. Keywords: Process audition, gyratory crusher, cone crusher, HPGR, screening, hydrocyclones, magnetic drum separators

Jan 1, 2020

By N. E. K. Schuttler

Experience with Mars pumping of underground water by N. E. K. SCHUTTLER (Visitor) As the result of a planned increase in production, Vaal Reefs Exploration & Mining Company Limited increased the hoisting capacity of their existing equipment to its fullest extent and installed Mars pumps and a washing plant. The layout of the installation is described, and details are given of the modifications made to overcome its weaknesses. Plans to change the present four-stage system to a seven-stage system are outlined.

Jan 3, 1977

By T.R. Stacey

Physical testing of rock support for rockbursting conditions has been carried out for over 40 years. A review of this testing shows that it has been mostly component based, rather than actually testing support systems. Further, it is concluded that none of the testing is truly representative of rockburst loading in a similitude sense. Similitude conditions are not achievable, mainly because the real conditions in a rockburst event, such as seismic source location and magnitude, wave frequencies, amplitudes, and interactions, are not all known. Because such information is not available, and because the results of all testing carried out to date have not been able to define, for support design purposes, the capacity of support systems, ongoing physical testing of rockburst support systems is essential. It is essential that the test should simulate, or actually take place in, a supported rock excavation. A rock support system is a combination of individual support components that work together to retain and contain the rock. In doing this, the components are subjected to loading by the rock and to interactive loading between one component and another. It is necessary to prove the capacity of such rockburst support systems by subjecting them to severe loading, as in direct blasting. The direct blasting approach, pioneered more than 40 years ago, probably still provides the greatest validity as a significant test of rockburst support capabilities, even though it does not simulate a rockburst. Direct blast testing of rockburst support systems in a surface environment, such as in a quarry or on exposed rock cutting surfaces, could represent a practical development of the approach, facilitating the execution and monitoring of tests.

Jan 1, 2012

By D. van Rensburg

Jointed rock slopes are generally stable, as there is no freedom of movement for blocks of rock. In an open- pit mining environment, blasting opens up space into which blocks of rock can fail, resulting in the common occurrence of slope failure. Prior to the blasting of a trim pattern, the immediate highwall is scaled, where loose rock material is removed by means of a mechanical scaler. As mining of the pit progresses, the height of the scaled highwall from the pit floor progressively increases. These highwalls are never scaled again for the remainder of the pit life, and time-dependant deterioration contributes to these highwalls becoming subject to rockfall and, sometimes, slope failure. This paper documents the development of a South African innovation, a remote-controlled mechanical highwall scaler, a world first for the mining industry. The scaler will enable open-pit highwalls to be scaled from crest to toe whenever the need arises. It will reduce the risk associated with highwalls and deliver on the Anglo American promise of producing safe, profitable platinum.

Jan 1, 2012

Council and Standing Committees, 1978-1979 President: Dr M. G. Atmore. Vice-Presidents: D. A. Viljoen and Dr P. R. Jochens. Honorary Treasurer: J. K. E. Douglas. Immediate Past President: P. A. von Wielligh. Members of Council: J. D. Austin, A. N. Brown, H. E. James, Prof. R. P. King, Dr D. G. Krige, Prof. F. Q. P. Leiding, D. G. Malan, C. S. McPhail, J. C. Mostert, G. Y. Nisbet, H. G. M. Rose, W. T. Ruhmer, G. C. Thompson, R. A. von Maltitz. Chairman, Witbank-Middelburg Branch: T. S. Wilmot. Chairman, Orange Free State-Klerksdorp Branch: H. M. W. Eschenburg. Past Presidents Serving on Council: R. J. Adamson, H. Britten, J. K. E. Douglas, Prof. D. D. Howat, Dr J. P. Hugo, D. G. Maxwell, Prof. R. P. Plewman, Dr R. E. Robinson, Dr M. D. G. Salamon, P. W. J. van Rensburg. Standing Committee Chairmen: Membership, Dr P. R. Jochens ; Technical Programme - Metallurgy, Prof. R. P. King ; Technical Programme - Mining, H. G. M. Rose; Vacation School - Metallurgy, J. C. Mostert; Vacation School - Mining, D. G. Malan/J. D. Austin; Awards, P. A. von Wielligh; Excursions, D. A. Viljoen; Adjudication, P. A. von Wielligh; Constitution, Rules and Policy, P. A. von Wielligh; Monograph Series, Dr R. E. Robinson; Professional and Technician Train¬ing Committee, Dr M. D. G. Salamon; Career Guidance, D. G. Malan; Phoenix National Committee, Dr R. E. Robinson; 1982 World Congress, Dr M. G. Atmore; Witbank Coal Colloquium, Dr P. R. Jochens; Mines and Works, P. A. von Wielligh.

Jan 1, 1979

By H. Scott-Russell

Much of the technology and methodology extensively employed in current mining operations is in the mature phase of its lifecycle and, consequently, subject to the principle of diminishing returns. It is probable that future gains in productivity and safety of the magnitude essential for the sustained economic viability of the industry will be derived only from a determined technological development programme. The history of trackless mechanized mining, which represented a radical change in methodology in deep-level gold mines, is reviewed. The benefits and obstacles to the realization of the full potential are highlighted. Similarly, an overview is given of alternative mechanization developments in South Africa. In addition to the development and application of advanced technology, an envelope of operating parameters relevant to each methodology must be engineered to facilitate the site-specific selection of the most appropriate. Furthermore, a mechanism for the evaluation of cost effectiveness is essential to the decision-making process. The narrow, tabular orebodies of relatively low dip that are encountered in the South African hard-rock mining industry make the design and manufacture of a comprehensive range of stoping equipment extremely difficult. The machinery that has been available to date has demonstrated only limited site-specific success. The development of suitable machinery must necessarily be initiated and driven by the South African mining industry in collaboration with the major equipment manufacturers in the world.

Jan 1, 1993

By F. A. G. M. Camisani-Calzolari

Approximately 850 groundwater samples were collected over a 29 300 km2 region of the semi-arid Northwestern Cape during the site selection phase of the South African radioactive waste disposal project. The purpose of the geostatistical investigation was primarily to delineate metallogenic occurrences and provinces which might exist below the thin veneer of surficial material and could thus interfere with the suitability of the site, and to quantify the distribution patterns of groundwater parameters in order to establish a relationship to local and regional geology. Up to 34 variables were analysed for each sample. Structural analysis revealed that the study area is statistically uniform. The variables have low correlation coefficients, with the exception of major ions, indicating a general poor degree of interrelationship between the spatial distribution patterns of the different variables. On the other hand, the long semivariogram range of the majority of variables, which reaches 70 km in cases, demonstrates their continuity on a regional scale. Kriging, which was repeated for each parameter, reveals that most variables, particularly trace metals, have distribution trends which are not influenced by local geomorphology or surface lithology. A 50 km wide, 220 km long metallogenic province, defined by kriging, could possibly reflect a broad metallogenic imprint on the basement and could represent a target area for prospecting. Kriging also reveals the possible existence of a wrench faulting system which may well have influenced the Namaqualand coastal graben and the western boundary of the Karoo.

Jan 1, 1987

By D. Mesa, J. Karvonenb, A. López, P. R. Brito-Parada, R. Grau, D. Davoise

The froth zone in flotation cells plays an important role in determining metallurgical performance. This is even more critical as cell sizes increase, since larger bursting surface areas can easily result in poor froth transport and even stagnant froth zones, which are detrimental to recovery. Generating additional overflowing lip length by adding internal launders and reducing surface area (while also directing the froth to the overflow) by adding crowders are well established design strategies to enhance froth mobility. However, comparative experimental studies of froth zone design modifications at industrial scale are scarce and often lack detailed froth characterisation. In this work, we present the results of two experimental campaigns that were carried out at Atalaya’s Riotinto concentrator in order to determine the effect of a new froth zone design on the flotation performance of a TankCell® e300 cell that operates as the first cell of the rougher bank. These campaigns provided a unique opportunity to assess froth phase phenomena and metallurgical performance before and after changes in design. The original cell design had an internal peripherical launder and a froth cone, while the new concentrate launder technology adds a centre launder and an adjustable froth crowder to the existing launder design. The new concentrate launder arrangement reduces significantly the froth area as well as the froth transport requirements, aiming to improve froth recovery and, consequently, enhance flotation performance, allowing copper recoveries in the TankCell® e300 cell to increase dramatically. In addition, radial profiles of froth height and froth velocity at the surface were determined, which provide valuable insight into the effect of design changes on froth stability and mobility. Keywords: Flotation performance, enhanced recovery, launder, crowder, froth stability

Jan 1, 2020