Search Documents

By J. Levin

Bond's Standard Work Index (SWi) indicates the grindability of an ore, and his Operating Work Index (OWI) indicates the performance of a grinding mil or circuit. The comparison of the two indices offers a measure of the efficiency of the grinding operation. Mil (or circuit) performance, particularly on the Witwatersrand, is often indicated by the index kilowatt -hours per tonne of minus 75 µm material produced (kWh/t minus 75µm or OE75)' The paper shows that a standard kWh/t minus 75 µm index (SE75) can be obtained from the standard Bond grindability test (which provides the SWi), and asks whether the two E75 indices can be used in the various ways in which the two Work Indices are used. For the answer, the paper presents averaged values for the standard grindability indices of the gold ores of the Witwatersrand, averaged values for the performance of grinding mils operating on those ores, and the results of laboratory grinding tests on a composite of several Witwatersrand ores. The particle-size indicator for the calculation of the Wi indices, the am size, is constant in its relation to the largest particles present, whereas the percentage minus 75 µm, the indicator of size for the E75 index, varies with the degree of grinding in its relation to the size of the largest particles. Because of this difference, the standard Work Index increases as the grind becomes finer, whereas the standard kWh/t minus 75 µ value decreases. The Wi and E75 indices nevertheless serve similar purposes when applied to moderately fine grinding-finer than 70 per cent minus 75 µm. Open circuit laboratory grinding tests revealed three stages in the grinding process, and credible values for the open circuit Work Index were obtained only from the second stage. The conversion of the open circuit Work Indices to the equivalent of close circuit indices by the application of Bonds open circuit inefficiency factor (a constant for grinds indicated by the d80 size) was of limited success; however, the development of a conversion factor related to particle-size should not be difficult. Initially difficulty was experienced in the calculation of the 0E75 indices from the results of the laboratory tests, but it was eventually considered that a constant value of the index derived from the results would be close to the true open-circuit index. The open-circuit grinding test could there fore be a convenient method for the detection of differences in the grindability of ores.

Jan 1, 1992

By U. Atici, R. Comakli

"Understanding rock properties is of vital importance in mining and civil engineering. Rock properties are generally determined through laboratory tests, which require a large number of uniformly shaped samples and technicians who use indirect methods to determine rock properties. The texture coefficient (TC), which represents various textural parameters including the size, shape, orientation, and relative proportions of grains and the matrix, is an efficient means for indirectly evaluating the mechanical behaviour of rocks. In this study, 12 different rocks (ten granites, one diorite, and one gabbro) were collected and their engineering properties. including specific gravity, porosity, P- and S-wave velocities, Schmidt rebound hardness, uniaxial compressive strength, and elasticity modulus, were investigated. Relationships between TC and these measured properties were assessed. Statistically significant (at the 95% confidence level) correlations were found between the TC and compressive strength, elasticity modulus, sound velocity (both compression and shear waves for dry and saturated samples), but no significant correlation was found with Schmidt rebound hardness. The results suggest that it is possible to use the relationships between TC and the mechanical properties of rocks in rock classification. IntroductionIn every aspect of rock engineering, knowing rock properties is essential for determining and predicting the behaviour of rocks and rock masses. Mechanical properties of rocks are important parameters in mining, geology, and engineering, and they are affected by textural characteristics such as grain size, grain shape, cement type, degree of cementation, mineral content, and the ratio of the grain area to the matrix area. The effects of textural properties on the physical and mechanical properties of rocks have been investigated for a long time, and previous studies revealed close relationships between single parameters related to rock texture and mechanical properties of rocks (Akesson et al. 2001; Gunsallus and Kulhawy 1984; Merriam, Rieke, and Kim, 1970: Onodera and Kumara 1980; Prikryl 2006; Ulusay, Tureli, and Bider, 1994; Tugrul and Zarif 1998). Rock properties are usually determined using mechanical tests, which require uniformly shaped and relatively large samples. However, it is not always possible to obtain such samples. Furthermore, rocks with similar textural and structural properties may exhibit different mechanical behaviour. Howarth and Rowlands (1987) developed a texture coefficient (TC) that expresses all the main textural parameters of a rock in a single dimensionless quantity based primarily on statistical assessment. The TC makes it possible to understand the effects of a rock’s textural properties on its mechanical properties using thin sections instead of large, uniform samples. Ersoy and Waller (1995) investigated the relationship between strength and TC for limestone, sandstone, and siltstone; they also examined the effect of rock properties and TC on drilling performance. Ozturk, Nasuf, and Bilgin (2004) explored the relationship between rock quality and TC by evaluating the uniaxial compressive strength (UCS) values of limestone, basaltic andesite, and tuff. Gupta and Sharma (2012) evaluated TCs as well as the petrophysical and mechanical properties of quartzite from the lower and higher Himalayas and found a strong relationship between TC and UCS. Similarly, Ozcelik, Bayram, and Yasitli (2013) investigated the relationship between TC and various parameters in marble by applying the statistical analyses developed by Ozturk, Nasuf, and Kahraman (2014)."

Jan 1, 2019

By K. L. Riemer

The West Wits Line first began yielding gold in the mid-1930s and is among South Africa's leading gold-producing areas. Gold mining operations are carried out amidst the occurrence of seismic events which cause both damage to underground excavations and injury and loss of life to production personnel. The feasibility of establishing a system to minotor the seismicity on all the Gold Fields mines was investigated during the early 1980s. This led to the establishment of a centralized seismic network in 1981. The system was structured around three major objectives. It uses Perkin Elmer (now Concurrent Computer Corporation) 16 and 32 bit mini-computers. The hardware in use at both the central and remote sites is outlined, giving a good insight into the role of computers in the system. The system software reveals the fast flow of data through the network; it can be divided into three categories: (1) data logging and transmission - remote sites, (2) data capture and communications - central site, (3) applications and research - central site. Several examples are given which show how the system is measuring up to its objectives. These case studies also indicate how the computers are effective in representing the seismic data collected. It is concluded that the use of computers enables the pin-pointing of seismic events on the West Wits Line within about 3 -4 minutes of their occurrence. The choice of hardware is largely dependent on the objectives of system, and the Gold Fields Network has chosen mini-computers because of the speed of communication and the large amount of data and storage required for research applications.

Jan 1, 1987

By E. L. Thyse, P. Bepswa

The Western Cape Mineral Processing Facility (WCMPF) is a collaborative educational initiative between the Department of Process Engineering at the University of Stellenbosch and the Chemical Engineering Departments at the University of Cape Town and the Cape Peninsula University of Technology. The primary objective of the WCMPF is to facilitate the education, development and graduation of suitably qualified engineering graduates and diplomats for the mining and mineral processing industries. In recent years the WCMPF has embarked on a number of initiatives aimed at improving the quality of mineral processing education which include, more importantly the introduction of novel ?end to end? or ?integrated? practicals. The practicals are developed around a specific mineral theme or route, which more than often includes the development of several new pilot plant practicals demonstrating key unit operations or processes in the selected mineral theme or route. The most recent mineral processing pilot plant practical programme is developed around the beneficiation of heavy mineral sands. The programme consist of the following developed pilotplant practicals: the online electrostatic separation of free flowing mineral sands using a Roche Mining Carrara high tension roll separator incorporating a Blue Cube Systems MQi in-line mineral quantifier; the production of titania-rich slag and pig iron from the smelting of ilmenite and anthracite in a 60 kW direct current (DC) plasma arc furnace as well as the mineralogical characterization of the feed and products; the continuous closed-circuit ball milling and screen classification of titania-rich slag. This paper illustrates the important role of a well-designed heavy mineral sands beneficiation pilot plant practical programme in facilitating the education and development of suitably qualified personnel for the mining and mineral process industries.

Jan 1, 2007

By D. Gregurek

The complexity of metallurgical processes in the non-ferrous metals industry. especially changes in the process conditions in combination with a diversity of metal processing furnaces, requires a precise knowledge of the system for the selection of refractory products. However, particular importance is still focused on the specific refractory consumption being as low as possible. The addition of recycling material with a high amount of impurities and the increase of low-grade ore concentrates used in the base-metals industry also entails a significant change of slag chemistries, process temperatures, etc., which influence the performance of already approved linings. This acknowledgement of process changes with decreased brick lifetimes provided the motivation for RHI AG to develop high-performance refractory bricks especially for non-ferrous metals applications. The internal laboratory tests with fayalitic slag showed very promising results compared with our approved magnesia-chromite bricks for this application. In order to identify suitable refractory products and to improve the life of the refractory lining, innovative product development has to be undertaken. In addition, the practical corrosion testing methods and facilities available within the RHI Technology Center, such as the induction furnace and the rotary kiln test equipment, allows the best possible understanding of brick wear at a laboratory scale. Based on the results of the test work, the optimal refractory solution can be recommended for a field trial at the customer?s site.

Jan 1, 2012

"Sampling error and bias, especially the Increment Preparation Error (IPE), are introduced when the tool allocated to do the job fails to extract a representative sample. This is the case with chip sampling; the tool can only extract haphazard shapes of loose or fractured material and not always from within the demarcated sample area. Increment Extraction Error (IEE) and Increment Delimitation Error (IDE) could be severe, but are found to be relatively unbiased. The uncontrolled action of the sampler in discarding excess sample material after sample collection has a significant impact on the error and bias introduced with each and every extraction. A new type of bias, referred to as the ‘waste discard bias’, arises when samplers select what portion of the excess sample material to discard at the sample site. Material visually identified as waste is discarded in preference to mineralized broken ore if there is an excess of sample material. This results in a considerable error in the analytical results. The bias is proportional to the reef-waste ratio in the demarcated sample. IntroductionTwo types of ‘sampling’ are distinguished, namely sampling of particulate materials (broken ores) and sampling of solid, unbroken in situ mineralized reef. This study considers only chip- or face-sampling of in situ, goldbearing, carbon-rich conglomerates typical of the Upper Witwatersrand Supergroup and examines where components of sampling error and bias, clearly specified in the Theory of Sampling, may arise during the practice of ‘face sampling’. Many millions of face samples have been extracted from Witwatersrand-type mines using a hammer and chisel, and detailed descriptions (standard operating procedures) of how the samples should be taken have been developed by many mining companies. There is, however, no taxonomy or nomenclature for managing or reporting the different types of errors associated with chip sampling. The Theory of Sampling compiled by Pierre Gy in the early 1950s provides, comprehensive nomenclature of sampling errors that is applied to particulate sampling of ore in a lot, a stockpile, or a moving stream on a conveyor belt. The taxonomy and characteristics of sampling errors, grouped according to the sources from which they arise, and identified by Gy (1973, 1979, 1982, 1992, 1995, and 1998) are shown in Figure 1. This classification of errors is used extensively in regard to the sampling of particulate materials in the mining and minerals industry, but not in regard to chip sampling. A relatively small mass (hundreds of grams) of representative particulate material for estimating the average grade of a much larger mass (thousands of tons – the ‘lot’ in the Theory of Sampling) is extracted by the chipping or cutting of a representative rock ‘sample’ from the stope face."

Jan 1, 2016

By X. Chen, G. Wang, D. Wan

Computational fluid dynamics have been applied for detailed modelling of particle-bubble collisions. The most accurate approach in the previous work is using the point particle method to treat particles and bubbles. Nevertheless, the sizes of particles and bubbles are generally bigger than the Kolmogorov scale in the high turbulence of the flotation environment, which makes the point particle method inappropriate. This paper describes particle-resolved direct numerical simulation on the collisions between particles (denoted as heavy particles) and bubbles (denoted as light particles) in a homogeneous isotropic turbulent flow field, and a comparison with the point particle method.. A largescale stochastic forcing scheme was implemented within the mesoscopic multiple-relaxation-time LBM approach to maintain turbulence intensity at targetted levels. Both kinematic and dynamic collision kernels were evaluated to study the correlation of total collision events and turbulent kinetic energy (TKE) dissipation rate. The results show that collisions between particles increase with the TKE dissipation rate as radial relative velocities between particles increase with it. In the particle-resolved simulations, the dynamic collision kernels were found to not match with the kinematic collision kernels as in the point particle method. Quantitatively, they were approximately 4 to 10 times smaller than the corresponding dynamic collision kernels. Therefore, it is not reasonable to estimate the kinematic collision kernel in particle-resolved simulations as its rationales are not valid. However, the collision behaviour can still be accounted for by means of the dynamic collision kernel since it is obtained from the direct statistical analysis of the collision events. Keywords: Lattice Boltzmann Method; particle-resolved simulation; multiphase flow; collisions

Jan 1, 2020

The 89th Annual General Meeting of The South African Institute of Mining and Metallurgy was held at Kelvin House, Johannesburg, on 20th August, 1986. Mr. H. E. James (President) was in the chair and declared the meeting open at 16hoo. Obituaries President: It is my sad duty to announce the deaths of the following members of this Institute: Life Fellow D.L. Carson; Retired Fellows T.K. Adams, G.E. Carlyon, N.M. Holford, D.E. Maclver, C.J. Morgan; Fellows S.K. de Kock, R.R. Porter, Dr G.J. Rees; and Associate Sir Lindesay Clark. As a mark of respect to the memory of the deceased and in sympathy with the bereaved, please rise and observe a moment of silence. Minutes President: The 88th Annual General Meeting of the Institute was held on Wednesday, 14th August, 1985, and the minutes were published in the September 1985 issue of the Journal. The minutes were confirmed.

Jan 1, 1986

This paper describes DRA?s involvement with the expansions at Tati Nickel, Phoenix Mine, that have taken an initial plant design of 3.6 Mtpa (originally built by Murray & Roberts), up to 5 Mtpa, and eventually 12 Mtpa capacity. Initially, the plant could not achieve the design name plate capacity for the first few years of operation, as a consequence of the notoriously hard and abrasive nickel ore affecting primarily the operation of the crusher circuit. In order to extend the life of mine, Tati? assessed and then redefined the mining plan, choosing to increase the Phoenix mine reserves to a lower cut-off grade. In order to increase nickel units produced, the concentrator had to therefore treat additional tonnage at lower head grades. Site investigations and field tests around the comminution circuits are outlined, indicated that the milling circuit could be increased to 650 tph, from the initial design of 470 tph, for a similar feed grade and recovery. A project was initiated to debottleneck the crusher circuit and achieve the new target throughput. (Project 5M). This was followed by a feasibility study of the impact of pre-concentration by DMS, which after promising laboratory tests, was followed up with the installation of a 200 tph ?demonstration? plant. The success of this demonstration plant provided the impetus to expand the supply to the 5 Mtpa mill from a large preconcentration stage. A gyratory crusher (one of the largest and most powerful) will receive ore directly from the open pit operation, feeding into a secondary-tertiary crushing plant followed by a modular DMS preparation circuit. Four large DMS processing modules have been installed to treat the tonnage, with high expected rejection levels. Finally a review of the DMS process capability on an ostensibly disseminated micro-gabbro nickel ore is given, which shows the remarkable impact that preconcentration can have on an operation, both in terms of profitability and a successful process ?expansion?. The performance of the DMS plant has significantly extended the life of mine, allowing the mine to significantly reduce mine cut-off grades and curb its previously selective mining practice.

Jan 1, 2009

By M. Gershon

During the exploration phase of mine development, drilling location is in the hands of the geologist, and drilling is spread over the entire domain of the property or deposit boundary. During the mine planning and production phases, however, the mining engineer also needs to use the information obtained from the drilling program. Thus it is important that he/she have some input into the selection of the drillhole locations. Usually, when exploitation will center on one portion of the property for the immediate future, the mine engineer will want to have more of the drilling performed in this area. In the early stages, the purpose of the drilling was to make a decision concerning whether or not to develop a mine. Once the decision is made to proceed with this development, the mine engineer needs to know, with as much confidence as possible, the estimate of the ore grade at each location where mining will occur. This paper addresses the problem of drillhole location for the needs of the mining engineer. The goal is to compare a variety of approaches to drillhole location with a new approach developed by the author. This approach is based on the theory of geostatistics, with the estimation variance used as the quantitative measure of the confidence attained. The goal of the algorithm is to select those locations that minimize the estimation variance subject to constraints on the number of drillholes and the total cost of the drilling program. The kriging equations are used as another set of constraints. The resulting nonlinear optimization model is expressed in terms of binary (0 - 1) decision variables leading to a solution by the branch-and-bound procedure. The algorithm has been applied at a number of operating properties, and practical results and suggestions for implementation are provided.

Jan 1, 1987

By S. J. Thomas, P. A. Lilly

With support from the Australian mining industry and the Federal Government, three Australian universities are collaboratively developing flexible-format, web-based course content and delivery in rock mechanics for undergraduate mining engineering students. This paper describes the educational philosophy behind the development and summarises other salient features of the Program. Mit der Unterstuetzung von der austlalischer Bergbauindustrie und der Bundesregierung, drei austlalische Universtaeten in Zusammenarbeit entwickeln flexibel Netzgengruendet auf Lehrganginhalt und Lieferung in Felsgestein fuer Bergbaustudenten. Dieses Schreiben erlautert das Unterrichtsphilosophie hinter der Entwicklung und Zusammenfassung anderer Hauptpunkte von diesem Programm" Avec l'assistance de l'industrie miniere australienne et du gouvernement federal , 3 universites Australiennes collaborent a la mise en place d'un programme de mecanique des sols pour etudiants- ingenieurs en mines. Ce programme serait a la fois flexible et accessible par Internet. Ce document decrit la philosophie pedagogique de ce projet et en souligne les characteres importants.

Jan 1, 2003

By H. M. Friede

A short survey is given of the Iron Age smelting sites and smelting furnaces that have been found in South Africa. An attempt is made to classify South African smelting furnaces by the inclusion of functional characteristics such as the numbers and positions of tuyeres. An affinity is suggested between the Venda (eastern Transvaal) type of furnace and an East African type. The principles of the smelting process in South African Iron Age furnaces and the characteristics of the smelting products are discussed. Results of metallographic and chemical analyses of 19 iron specimens found at South African sites are given and compared with those from sites in Zimbabwe-Rhodesia, Mocambique, and Nigeria. The carburization and steeling of iron during primitive smelting and forging are discussed.

Jan 1, 1979

By M. H. M. von Wielligh

"Brick manufacturers supply a variety of uniquely coloured facebricks to the building industry, which requires a high level of colour consistency in the products. Colour variation in bricks is influenced by the composition and consistency of the white clay raw material. By blending varieties of naturally occurring white clay the manufacturers produce a unique range of facebrick products. Homogeneity of the white clay raw materials mined at Lenasia is crucial for producing bricks of consistent colour. Geostatistical investigations of the major element distributions (SiO2, Al2O3, Fe2O3, and K2O) and loss on ignition (LoI) were conducted. An analysis of the spatial continuity of these variables followed by ordinary kriging indicated that the upper white clay layer at Lenasia is richer in K2O and Fe2O3 than the lower layer. Consistency in the colour of facebricks depends critically on careful management of the variability in the K2O and Fe2O3 content of the clays. The geostatistical approach to understanding the distribution of elements in the clay allows miners to construct clay stockpiles of consistent quality for feeding the brick-making process. Geostatistical investigation of the chemical contents in other clay domains within the deposit is recommended, and could be extended to all facebrick manufacturers to assist in improving the colour consistency of their products. IntroductionMost clay in South Africa is used in the manufacturing of tiles, pipes, bricks, whiteware, refractories, and pottery. Bricks are manufactured from a wide variety of clay types, the behaviour of which during firing depends critically on the the clay mineralogy and chemical composition, but this relationship not well understood (Stein, 1982). The variety among clay deposits is related to the different processes of formation (Deer, Howie, and Zussman, 1992). The geochemical composition of the clay can vary between layers and within the same layer in an individual deposit (Lurie, 1984). The properties of clay minerals are determined by their structures and the different combinations of silicate layers, cations, and hydroxyl ions (Kingery, Bowen, and Uhlmann, 1976). South African clays can be classified as either kaolinite or montmorillonite and are seldom found in a pure form (Lurie, 1984). Different clay minerals affect the drying, forming, firing behaviour, colour, and quality of the brick product in different ways. Laboratory tests (full physical analysis) can indicate the suitability of a clay for the manufacture of ceramic products. The minerals most essential for the manufacturing of clay brick products are kaolinite, illite, and quartz (Stein, 1982)."

Jan 1, 2017

[Consider a square block W in an ore body S2, to be valued from one centre sample w, and one corner sample w2 (Fig. 9.1). The sample set is ws = Iw,;w21. We can estimate the block average µw by the average of the sample values x, and x2: µw = 'z (x, + xz). (9.1) The error made is measured by the estimation variance: o' (ws to W) = 2 - (ws; W) - - (ws;ws) - - (W; W). (9.2) However, we know that the centre sample w, gives more information about the block value than the corner sample w2. In the example studied in § 8.4, where w, and w2 were considered to be points, we found that of (w, to W) was nearly one third smaller than o2E (w2 to W), therefore when estimating W one should give more weight to w, than to w2. In general, when evaluating a block W from a set of n samples ws, where WS = l w;w2; ... wn1, a better estimator of µw can be obtained if we give different weights to the sample values, depending on the size and the positions of the samples. Some desirable properties of such an estimator µw are: ? It should be a linear function of the sample values xi: n µw = bi xi (9.3) =t where bi = weight given to sample x . ? It should be unbiased, i.e. its expected value should be equal to the true block value: E [µw - µw] = 0. (9.4) ? The mean squared error of estimation of µw should be a minimum E [(µw - µw)2] = a minimum. (9.5) The estimator which satisfies these properties is a minimum variance, linear and unbiased estimator, and is known as the kriging estimator. The corresponding error of estimation is the kriging error. This estimator is also known as the BLUE (for Best Linear Unbiased Estimator) estimator. This was named by Matheron in acknowledgement of the early work of Krige's in the optimization of the evaluation of the South African gold mines. The following notations will be used: µK kriging estimator. o2k = o2K (w,, to W) kriging error.]

Jan 1, 1978

The April General Meeting of the Institute was held in Kelvin House, Johannesburg, on 16th April, 1969, at 4.30 p.m. Mr R. C. J. Goode (president) was in the Chair. There were also present nineteen Members, including Messrs R. J. Adamson, F. P. Bath, J. K. E. Douglas, A. R. C. Fowler, P. Lambooy, D. G. Maxwell and J. A. Nixon, (Council Members), Messrs E. L. Atkinson, I. R. Chaston, J. L. Edwards, J. S. Hall, S. A. Hancox, A. F. Lee, W. K. B. Loftus, H. S. Simpson, A. N. Shand, R. A. Wilson, H. J. Wright and J. E. Van Leeuwen. Nine Associate Members, including Messrs O. Davel, G. Douglas, P. R. Garcia, D. J. Murphy, D. Rankin, G. Schwartz, H. N. Singer, S. Thompson and D. A. Viljoen. One Graduate Mr D. Bosley. Ten Visitors, including Messrs S. Adler, C. E. Alvey, B. J. Botha, K. Chant, L. W. Davis, R. N. Guest, R. V. Keet, E. G. Keown, M. D. Lourie and S. McMurray. Secretary Mr D. C. Visser. Total present: Fourty-one. MINUTES The President requested that confirmation of the minutes of the previous meeting be held over as they would only be appearing in the Journal of the following month. Agreed. MEMBERSHIP The President: "I have much pleasure in announcing that the names of the under-mentioned candidates, having been published in accordance with By-law 5.2.2, Council has elected them to membership of the Institute in the following grades: Members: Kenneth Sinc1air Rae, Ian Robert Malcolm Chaston. Associate Members: Norman Isaac Thomas, Ian Connell Robinson. Graduates: Simon Richard Jeremy Perkins, Bleddyn Reginald Lear, David Williams. Affiliate: Richard Robert Will. Students: Angus David McElwee, Clive Renard Archer, Peter Andrew Locke. MEMBER TRANSFERRED TO A HIGHER GRADE From Graduate to Associate Member: Patrick James Burns. I welcome the newly elected members to the Institute and congratulate the member who has been transferred to a higher grade." (Applause). GENERAL BUSINESS The President reminded members that a buffet supper at a cost of 55c would be available after the meeting. PAPER FOR PRESENTATION The President noted with pleasure that a strong contingent from De Beers and the Finsch Mine were present. He expressed gratitude to Mr Loftus for coming

By A. P. L. Kotzé

Modelling and scheduling for Grootegeluk coal mine, situated in the north- western Transvaal, is by means of a series of modular systems. Modelling of the multilayered body, which is part of the Waterberg coalfield, was based on a detailed study of the behaviour of coal and waste qualities and the sub- sequent use of standard geostatistical techniques. A notable improvement on previous methods was attained. Scheduling procedures and systems were developed to model a multibench pit producing coal for several metallurgical plants as well as a power-station. Scheduling was done by producing a series of longitudinal cuts, the cuts being subdivided into increments. By allocating cuts to certain periods, the resulting calculated product tonnages were com- pared with production targets, and by iteration a final scheduling sequence was determined.

Jan 1, 1987

By J. Petersen, T. Moyo, J. Dinga

The leaching of chalcopyrite in ferric sulfate media is notorious for its slow and inhibited kinetics. Different methods have been proposed to improve the kinetics, including the use of organic compounds as additives to the leaching media. In this study, the enhancing effect of methanol, ethanol, 1-propanol, and 2-propanol on the leaching of chalcopyrite in aerated acid ferric sulfate solutions using different reactor systems was investigated. The results revealed a clear improvement of copper dissolution by methanol and 1-propanol relative to tests with no additives under similar conditions. Operating a continuous-flow mini-column reactor yields surprisingly good results, potentially related to the maintaining of a consistent leaching micro-environment on the mineral surface. Scanning electron microscopy studies showed that the alcohols result in the removal of surface deposits formed during the anodic dissolution, potentially thus facilitating improved cathodic reduction of the ferric ion to drive the anodic dissolution.

Jan 1, 2023

By H. Skretting, J. Gundeesen

The paper compares operational parameters for the electric reduction smelting of pig iron and ferroalloys in pilot and industrial furnaces. Data from two pilot furnaces of approximately 200 and 500 kW operating-load capacity, as well as from several production furnaces, are included. Examples are given for the smelting of pig iron, ferronickel, ferromanganese, ferrochromium, and ferrosilicon. In most instances, the results from the pilot furnaces, such as the values for consumption and product analyses, corresponded fairly well with comparable data from the industrial furnaces. For ferrosilicon, the power consumption in the pilot furnace was higher than that in the industrial furnace.

Jan 1, 1979

By Y. Belloa, C. Dorfling

The presence of impurities such as Se and Te in copper sulfate leach solutions can have a detrimental effect on electrowinning efficiency. These elements can be removed from the solution by precipitation; sulfurous acid is commonly used as a precipitation reagent, while studies have also reported improved precipitation with the addition of metallic copper. This paper aimed to determine the effect of conditions used during the solution purification step on the characteristics of the precipitates that formed. Precipitation tests were performed in a batch reactor with copper sulfate leach solutions obtained from the base metal refinery of a platinum group metal producer. The effects of agitation rate (250 and 500 rpm), SO2 flow rate (4.4 and 5.8 mL/min.L), temperature (65 and 95°C) and metallic copper powder addition (0, 1 and 2 g/L) on the characteristics of the precipitates formed during the tests were determined using scanning electron microscopy. The major phases detected in the precipitates formed when using SO2 as the only precipitation reagent were elemental Se and Cu2Se. The introduction of copper powder led to the production of different sulfide phases for the experiments conducted at 65°C irrespective of the values of the other reaction parameters. At 95°C, Cu crystals, Cu2O and tiny inclusions of Cu2(Se,Te) were the prominent phases noticed in the precipitates produced from all the tests conducted with copper powder as precipitation enhancing reagent. Keywords: copper, precipitation, selenium, tellurium

Jan 1, 2020

By H. Brüggemann

The exploration of deposits generates geological data which are suitable for creating a preliminary tectonic and stratigraphic model. Linked with the topographical map and analysis data from exploration drillings, this information forms a numeric representation of the deposit. The following example demonstrates an expert system which connects chemical quality requirements and quarrying criteria, and develops a quarrying strategy based on the calculated model. Additional constraining factors like process technology, quarrying methods, landscape protection regulations, etc. are included. The goal is to guarantee a long-term, homogeneous material flow from the quarry at acceptable production costs - even in the case of an extraordinarily inhomogeneous deposit. In order to fulfil this requirement it is necessary to consider a large number of rules, criteria and instructions which can be structured as an expert system and programmed with LISP at a comparably low cost. The chosen strategy is not necessarily final, but can be changed any time by altering or varying the framework of conditions. The output consists of a block-working sequence which best satisfies the set requirements for appropriate points of quarry opening.

Jan 1, 1987