Search Documents

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

B 2 Program Use Instructions necessary to execute the program, after the card deck has been prepared, are summarized in the following. B 2. 1 Input Data Format Input data is supplied to the program in two ways a. By data cards that are read in after program compilation. b. By data specifications that are included within the program.

Jan 1, 1976

By W. S. Sanner

A High Splint coal was carbonized in a low-temperature, fluidized-bed sys-tem to study the effects of thermal cracking on the products of decomposition. The coal was fluidized in recycle gas at 485° to 600° C, and the products were cracked at 600°, 700°, and 800° C in a bed of fluidized coke. Yields of tar, pitch, paraffins, and olefins decreased as carbonization temperature increased. Thermal cracking of the tar vapors produced the highest tar yields at 600° C, and light oil yield increased at cracking temperatures up to 700° C. At an 800° C cracking temperature, the yield of light oil decreased.

Jan 1, 1969

By John C. LaScola

The Bureau of Mines repeatedly surveyed a grid of monuments over an active longwall mine panel in southwestern Pennsylvania during a 1-year period. Both conventional ground surveying techniques and photogrammetry were used. The objective of this investigation was to compare elevation measurements of subsidence obtained from aerial and ground survey methods under dynamic ground conditions. The results of a statistical analysis of the survey data show that the mean of the differences between 372 matched pairs of elevation measurements was 0.20 ft (61 mm) with a 95-pct-confidence interval of 0.05 ft (15 mm). The mean of the absolute values of the differences was 0.38 ft (116 mm) with a 95-pct-con-fidence interval of 0.04 ft (12 mm). Ninety-five percent of the absolute values of the differences were less than 1.11 ft (338 mm).

Jan 1, 1988

By Stephen W. Lambert, Michael A. Trevits

The Bureau of Mines examined the wellbore of a vertical gas drainage well in the Mary Lee coalbed to determine the results of specific completion procedures in coal. A jet-slotting tool was used to cut four vertical slots through the casing about 1 ft below the coalbed. Even though stimulation treatment pressure was excessive, hydraulically induced channels were contained entirely within the target coal zone. Sand-filled, induced channels were horizontal, inclined, and vertical, and were propagated in directions similar to bedding planes, rock joint, and coal cleat directions measured in the mine. Variable gas flow rates, recorded during the productive life of the well, were attributed to chronic downhole pump malfunction and the slotted casing below the production zone.

Jan 1, 1978

By J. H. Perry, Joseph Cervik, G. N. Aul

The Bureau of Mines is conducting research to determine the effectiveness of long holes in degasifying an area of the Upper Split of the Lower Sunnyside coalbed at Kaiser Steel CO.'s Sunnyside No. 1 mine. These holes were drilled from the two outside entries of a section that was closed to mining because of excessive methane emissions. Two holes drilled to 430 and 450 feet produced initial gas flows of 160,000 and 127,000 cfd, respectively. Sixteen days after the completion of the second hole, the total gas production declined to just over 144,000 cfd. In 9 months of degasification, over 35 MMcf of commercial-quality gas has been removed from the coalbed. The combined gas flows declined to 106,000 cfd in the 9-month period. The two holes have reduced face emissions by about 40 pct.

Jan 1, 1978

By an Slo, J. J. Forbes

"INTRODUCTION This is the first of a series of information circulars dealing with the control of roof and the prevention of accidents from falls of rock and coal. These circulars are being published to focus attention of the coal-mining industry on this most prevalent source of fatalities and injuries and to present factual information that should be helpful in reducing loss from these causes.Records of fatal accidents in the coal mines of the United States, from all causes, have been kept since 1906; during this period approximately 30,000 men have been killed by falls of rock and coal in the bituminous-coal mines, and more than 7,000 men have lost their lives in the Pennsylvania anthracite mines from the same causes. From 1906 to 1930, about 900 men were killed annually by falls of rock and coal in bituminous-coal mines, and about 200 men were killed annually in anthracite mines during the same 25-year period. From 1931 to the present time, the number killed annually from falls of rock and coal has averaged more than 500 men in bituminous-coal mines and about 125 men in Pennsylvania anthracite mines.Numerically the record of accidents from falls of rock and coal shows improvement, but on a percentage basis and on a million-man-hours-of-exposure basis little, if any, improvement has been made during the past 40 years. The cold fact is that, year after year, about 50 percent of all those killed in coal mines in the United States lose their lives from falls of rock and coal."

Apr 1, 1948

By M. A. Elliott, H. H. Schrenk, L. B. Berger, John C. Holtz

"INTRODUCTION Among the hazards that may attend the use of Diesel engines in mines, tunnels, or other underground operations the presence of harmful or objectionable constituents in the exhaust gas must receive due consideration to prevent the formation of unsafe or unhealthful working environments in these places. Previous reports of this series have presented discussions of the composition of exhaust gas from engines in proper mechanical condition, 6/ the effect of adding some of the exhaust gas to the intake air of the engine, 7/ the effect of operation in atmospheres containing natural gas, 8/ and the effect on exhaust-gas composition of conditions that influence the characteristics of fuel injection in Diesel engines. In all these studies the properties of the fuels used were in general conformity with specifications usually recommended by the manufacturers of Diesel engines. In evaluating the physiological significance of the various components of the exhaust in these experiments, the toxic or objectionable gases determined were carbon monoxide, carbon dioxide, oxides of nitrogen, and aldehydes. Because of the low sulfur content of' these fuels, compounds such as sulfur dioxide and sulfur trioxide were not determined, although in discussion of the test results attention was directed to the fact that if fuels of higher sulfur content were used, the concentration of such compounds in the exhaust would become a significant factor in establishing the quantity of ventilating air required to furnish satisfactory dilut1on of the exhaust gas in underground working places."

Jun 1, 1943

Improve the effectiveness of person-wearable self-contained self rescuer (PWSCSR) training by enhancing the memory retention of trainees in proper donning procedures. Background In the fall of 1989, a total of 185 miners and inspectors were trained by Bureau of Mines personnel to don the SR-100 PWSCSR using the Bureau's 3+3 method. With the exception of a few individuals, miners were trained underground in an area set up within their working sections. The instructional protocol was as follows: (1) after placing an SR-100 simulator (equipped with a cleaned and disinfected mouthpiece assembly) on the mine floor in front of the worker, a researcher guided him or her step-by-step through the complete donning procedure, (2) the miner was required to perform each step slowly, methodically, and correctly while being talked through the sequence, (3) following this pre-practice instruction, the apparatus was repacked and the subject donned the device without coaching, while being evaluated, (4) if an error was made, the worker received corrective feedback, the unit was repacked, and the entire donning trial was redone. This procedure was repeated until the miner achieved a perfect 3+3 sequence.

Jan 1, 1990

Legislation and Government Programs.-On February 4, 1977, the Occupational Safety and Health Administration (OSHA) issued its final environmental impact statement on the occupational use of inorganic arsenic.2 The statement examined the ramifications of the original proposed standard published in the Draft Environmental Impact Statement (DEIS).3 The DEIS proposed to limit the exposure of employees to no more than 4 micrograms of arsenic per cubic meter of air as determined on an 8-hour-time-weighted average basis; or a ceiling limit of 10 micrograms of arsenic per cubic meter of air based on a 15 minute sampling period. The purpose of the proposed regulation is to reduce the risk of smelter workers developing lung and skin cancer as a result of exposure. A comprehensive study compiled by the Committee on Medical and Biologic Effects of Environmental Pollutants concluded that "there is strong epidemiologic evidence that inorganic arsenic is a skin and lung carcinogen in man."' In April 1977, the Environmental Protection Agency (EPA) served notice to ASARCO Incorporated that its Tacoma copper smelter and associated arsenic-producing facilities were in violation of State laws which limit sulfur dioxide and particulate matter emissions. This notice followed the Washington State Pollution Control Hearing Board overturning a prior ruling by the Puget Sound Air Pollution Control Agency (PSAPCA) which had permitted a 5-year variance from the State of Washington air quality standards. In December 1977, ASARCO appealed in court the decision of the Hearing Board.

Jan 1, 1980

By J. G. Walters

In a survey of the coking properties of United States coals, the Bureau of Mines has accumulated data on more than 500 coals and blends tested by the Bureau of Mines-American Gas Association (BM-AGA) method.4/ The importance of these tests depends upon the fact that a greater number of different coals has been tested in this apparatus than in any other of similar scale, thus permitting comparison of the carbonizing properties of many coals. Evaluation of BM-AGA results with respect to industrial data supplied by member firms of the American Gas Association was one of the first objectives in developing this test apparatus and procedure. Early data showed that, de-pendent upon BM-AGA carbonizing temperature, BM-AGA and commercial results agree closely.5/ Because of limited data, statistical relationships were not established at that time.

Jan 1, 1959

By J. R. Allsup

The Bureau of Mines studied the characteristics of simulated coal gas as an automotive fuel in two multicylinder vehicles in a standard and high-compression-ratio engine configuration. While using simulated coal gas fuel, increasing the engine compression ratio improved the fuel economy and vehicle performance but increased hydrocarbon emissions by 40 pct. photochemical reactivity of exhaust hydrocarbons was found to be extremely low using the coal gas fuel. An oxidizing catalyst used with the simulated coal gas fuel eliminated all but trace amounts of carbon monoxide and reactive hydrocarbons in the exhaust. Spark gap geometry and firing voltage were varied and, within the range tested, had little effect on vehicle performance and emissions using simulated coal gas fuel.

Jan 1, 1975

By Daniel C. Boteler

Data from 68 entrained-bed carbonization tests were treated statistically by the Bureau of Mines, and several useful relationships were developed among the major variables. Nine coals, ranging in rank from lignite A to high-volatile A bituminous, were carbonized in two entrained-bed carbonization pilot plants. The carbonizing reactors employed were vertically mounted cylinders, internally heated, refractory-lined, and 10 inches ID. The range of carbonization temperatures was from 825° to 1,600° F. Using a regression-analysis computer program, empirical equations were developed by which carbonization temperature, air-to-coal ratio, devolatilization of coal, char yield, and volatile matter content of product char may be predicted.

Jan 1, 1973

By Maria I. De Rosa

The U.S. Bureau of Mines performed experiments to determine if the primary gas toxicities evolved during the early (-300° C) and later (>400° C) combustion stages of mine conveyor belts could be predicted by a smoke particle characteristic. The experiments were conducted in an approximately 20-L furnace at set furnace temperatures of 150°, 250°, and 1,000° C, with a furnace airflow of 10 L/min. The variables studied, as a function of time, included hydrogen chloride and carbon monoxide concentrations, the average smoke particle diameter (d8 and number concentration (no), and the product of the average smoke particle diameter and concentration (dgn0) Other variables included the sample and furnace temperatures and the sample mass weight loss. Results show that the inverse of the smoke particle diameter-concentration product (ldgn0), correlates directly with the hydrogen chloride and carbon monoxide toxicities released in large quantities during the early and later stages of combustion.

Jan 1, 1989

By D. R. Douslin

This report describes an inclined-piston pressure gage that operates from a zero-pressure datum level. The gage is adaptable to accurate vapor-pressure measurements in the low and intermediate pressure range, 0.01 to 40 mm (mercury). Residual friction in the oil-lubricated piston-cylinder combination is eliminated by a unique oscillatory method that is free of end thrust on the piston and allows the full sensitivity of the gage to be realized. The axial component of the weight-to-area ratio of the piston is determined by measuring the angle of inclination with a goniometer that can be read to 1 sec. Accuracy of the gage proper is estimated to range from 0.001 to 0.012 mm from lower to upper pressure limits. Its highest practical sensitivity is about 0.0005 mm. As a test, the vapor pressures of ice and water were measured in the range -30° to +20° C.

Jan 1, 1963

By William G. Gruzenaky

The separation of yttrium and the individual rare-earth elements (lanthanons) from mixtures in which they occur has been a difficult problem through-out the years. Because of the increased interest in the various uses of these metals, the economy of their production may become of great importance. Studies relative to this problem, undertaken at the Federal Bureau of Mines Albany Metallurgy Research Center, resulted in the development of a solvent extraction method by which yttrium can be separated from the rare-earth metals. A separation factor of 10.93 was obtained between yttrium and cerium from a single-stage extraction, and a factor of 1.78 was obtained between yttrium and erbium from a multistage system. The valuable metals were extracted from euxenite by caustic soda fusion or by chlorination, and several separation methods were investigated. Partial separation of the yttrium and rare-earth element fraction was made by chemical methods and by solvent extraction. Thermal decomposition of aqueous rare-earth nitrates or selective ignition of yttrium and rare-earth oxalates yielded a fraction enriched in cerium. A fraction enriched in the light rare-earth elements resulted from a double sulfate precipitation, whereas a potassium ferrocyanide pr cipitation yielded a fraction enriched in yttrium. Precipitation with dimethyl phosphate yielded a fraction enriched in yttrium and heavy rare-earth elements. Enriched fractions were obtained with several solvent extraction systems. A system consisting of rare-earth nitrates, nitric acid, and tri-n-butylamine-3 methyl-2-butanone favored the separation of yttrium from the heavy as well as from the light rare-earth elements.

Jan 1, 1961

By Gregory P. Cole, Jeffrey Shawn Peterson

The Pittsburgh Research center3 conducted research to study and improve electrical fault detection on coal mine direct-current (dc) trolley systems. A suspended trolley line delivers power at voltages of 300 or 600 V dc to the haulage equipment and other loads. Roof falls or other accidents may force the trolley line down so that an electrical fault current may flow between the trolley line and rail. This fault current could result in localized heating, arcing, and perhaps fire. Such faults are not always preventable by the existing circuit protection because the current magnitude is well below typical operating levels of the trolley system. The research discussed in this report studies the applicability of computerized signal analysis techniques to solve this problem. Tests were conducted at cooperating coal mines. Measurements were taken during normal loading of the trolley system (light, intermediate, and heavy traffic), during induced fault conditions (arcing and bolted faults), and during transitions between the two. These data were then used to train and test a microprocessor-based fault detection algorithm. Later, field tests of the detection algorithm found that it correctly classified the state of the trolley system greater than 95% of the time.

Jan 1, 1997

Reduce the costs associated with conventional treatment of acid mine water. Approach Conventional treatment of acid mine drainage consists of plants requiring large mixing and aeration tanks, mechanical aerators and large, shallow settling ponds. Such plants are usually very costly to construct, maintain and operate. The Bureau of Mines has developed a simple, low-maintenance, highly efficient system to treat acid mine drainage which mixes, aerates, and neutralizes mine water Simultaneously in the existing discharge pipeline by using the pressure generated by the deep mine discharge pumps. The mixing and aeration action of the in-line system significantly increases oxidation rates of ferrous iron. Iron and manganese are removed, even at near neutral pH levels, due to the high efficiency of this system. How It Works The In-line Aeration and Treatment System (ILS) consists of two commercially available components, a jet pump (ejector) and a static mixer. The jet pump is simply a nozzle that converts water, already under pressure, into a high-velocity stream that entrains air by Venturi action. If neutralization is required, sodium hydroxide or lime is added along with the air at the Venturi opening. The aerated and neutralized water then enters the static mixer, which is a length of internally spiralled pipe that mixes air and water together. The two components, which are both about 8 feet in length, replace the last section of discharge pipe at a point before the mine water is emptied into a pond. Along with the settling pond, these components treat the water so that it meets discharge criteria. The system has been used at surface drainage treatment facilities as well, but in such use a pump is required to provide the necessary pressure drop across the Venturi opening.

Jan 1, 1985

By Fun-Den Wang

Finite-element structural analyses were performed to determine the stress distribution and displacements around a single rectangular coal mine opening in a multilayered rock system. The effects of changes in mechanical properties of roof and coal layers, roof layer and mine opening geometry, horizontal-to-vertical load ratio, and structural geologic features on the stress distribution about the opening were studied. Variability in the stiffness and relative thickness of the immediate roof layers can produce a considerable difference in the stress distribution about the opening as compared with that of a homogeneous material. Changes in opening width and horizontal-to-vertical load ratio have different effects on the stress distribution about the opening depending on the composition of the roof layers. In general, where a stiff layer exists in the roof at the surface of the opening, the stresses are higher in the roof and ribs around the opening. Horizontal changes in facies in the roof layers produced by structural geologic features can also greatly alter the stress distribution about the opening compared with the simple layered cases.

Jan 1, 1974

By Henry E. Blake

The purpose of this Bureau of Mines investigation was twofold. The first phase of the work was to determine the technical and mechanical feasibility of defluorinating low-grade siliceous fluorspars on an intermediate scale by high-temperature pyrohydrolysis in a rotary kiln. The second phase was to react the liberated hydrogen fluoride (HF) offgas with alumina monohydrate to produce commercial-grade aluminum fluoride (85 percent AIF3). The two phases of the work were to be integrated into a single continuous process. Evaluation of the data shows that low-grade siliceous fluorspars can be successfully defluorinated, either in a solid or a molten state, in a gas-fired rotary kiln in the presence of water vapor at 1,250° to 1,350° C. The water produced by combustion of propane was sufficient to yield defluorinatians of 75 to 85 percent.

Jan 1, 1962

[ ]

Jan 1, 2012