Search Documents

By A. F. Jolly

As a part of ongoing research into the sulfidation partitioning of selected complex minerals, the U.S. Bureau of Mines conducted research designed to selectively recover Cu from sulfidized chalcopyrite (CuFeS2). Ferric chloride (FeCI3) solutions leached >90 pct of the Cu and <20 pct (sometimes < 10 pct) of the Fe in the sulfidized concentrates. Cupric chloride (CuCI2) leaches were even more selective, solubilizing essentially 100 pct of the Cu and < 5 pct of the Fe. In contrast, leaching non-sulfidized CuFeS2 with either FeCl3 or CuCl2 showed that somewhat more Fe than Cu dissolved. These studies demonstrate that Cu is substantially more leachable from sulfidized CuFeS2 than from nonsulfidized CuFeS2? The Cu-and Fe-bearing constituents generated as sulfidation products, CuS (covellite) and FeS2 (pyrite), respectively, are differentially dissolved. The solubility of Fe from pyrite in sulfidized CuFeS2 is much lower than the solubility of Fe from complex nonsulfidized sulfide where Fe and Cu are bound in the same crystal lattice. Thus, the Cu dissolves selectively, producing a high-Cu filtrate from which Cu can be recovered by cementation or by electrolysis. Flotation of CuS-FeS2 mixtures indicates partitioned phases can be physically separated if effective liberation can be achieved. Magnetic separation tests yielded less promising results.

Jan 1, 1991

By Eugene T. Sheridan

This report presents statistical data on individual plants in the fuel- briquet and packaged-fuel industries circularized by the Bureau of Mines, United States Department of the Interior, in its 1957 annual survey. This survey revealed that 17 briquet and 23 packaged-fuel plants were active part or throughout the year. The annual production capacity of the fuel-briquet industry was 3,088,000 net tons, a decrease of 17 percent from 1956. The decline in capacity was caused in part by the permanent retirement of 4 plants and also by the reduction in capacities of 4 other plants. The rate of production of briquet plants also decreased as the industry operated at 35.8 percent of capacity compared with 40.9 percent in 1956. Every operating plant in 1957 had an annual capacity exceeding 25,000 tons.

Jan 1, 1958

By W. L. Hunter

Eleven steelmaking heats are described in this Bureau of Mines report in which acid practice was used to produce carbon steel from pre reduced iron ore pellets. Furnace slags obtained with no flux addition to the charge became quite viscous as they cooled, which precluded pressure casting from a ladle. Lime was added to the furnace charge at two levels to eight of the heats to modify slag characteristics in the furnace, and to the ladle in two heats to further modify the ladle slag cover. Selected ingots from nine heats were successfully rolled on a commercial mill to produce No. 10 reinforcing bar.

Jan 1, 1974

By J. P. Baur

The sensitivity of radiochemical techniques makes possible the study of the initial-stage sulfuric acid leaching kinetics of chalcopyrite and other copper sulfide minerals. This Bureau of Mines study of the initial leaching of chalcopyrite used techniques to evaluate the molecular and electrochemical processes. High-grade Transvaal chalcopyrite was neutron-irradiated in a TRIGA reactor4 to produce radioisotopes copper-64, iron-59, and sulfur-35. Dissolution rates were measured in the time interval zero to 60 minutes, during which time significant anomalies were observed. First was an initial period of rapid dissolution lasting a few minutes; second, an arrest or ?plateau? region usually lasting from 6 to 10 minutes; third, a second period of dissolution of lesser rate than the first. The effects of solution variables such as pH, oxygen partial pressure, and ferric ion concentration at different temperatures were measured.

Jan 1, 1974

By J. H. Perry

The Bureau of Mines is conducting research to determine the effectiveness of long holes in degasifying an area of the Upper Split of the Lower Sunnyside coalbed at Kaiser Steel Co.&apos;s Sunnyside No.1 mine. These holes were drilled from the two outside entries of a section that was closed to mining because of excessive methane emissions. Two holes drilled to 430 and 450 feet produced initial gas flows of 160,000 and 127,000 cfd, respectively. Sixteen days after the completion of the second hole, the total gas production declined to just over 144,000 cfd. In 9 months of degasification, over 35 MMcf of commercial-quality gas has been removed from the coalbed. The combined gas flows declined to 106,000 cfd in the 9-month period. The two holes have reduced face emissions by about 40 pet.

Jan 1, 1978

By R. K. Clifford

Chalcopyrite (CuFeSz) concentrates produced on the Lead Belt of Missouri typically contain 28 pct Cu and from 0.5 to 1.5 pct each of nickel and cobalt. Most of the nickel and cobalt are present as the mineral siegenite, (Ni,Co)3S4, almost none of which is recovered presently. The Bureau of Mines, U.S. Department of the Interior, has been conducting research on the chalcopyrite to produce a marketable fraction enriched in cobalt and nickel. Ferric chloride leaching of various chalcopyrite (copper) concentrates has yielded residues containing from 10.2 to 16.2 pct Ni and 8.3 to 11.4 pct Co with recoveries of approximately 79 pct. In another approach, laboratory froth-flotation tests have been conducted to investigate the effects of regrinding, roasting, baking, and steaming prior to flotation, with a variety of reagents. The best laboratory results were obtained after regrinding the copper concentrate to 94 pct minus 400 mesh and floating the chalcopyrite at natural pH (6.5) with 0.48 pound of sodium diethyldithiophosphate and 0.01 pound of sodium cyanide per ton of concentrate. This procedure yielded a tailings assaying 20.4 pct Cu, 5.2 pct Ni, and 3.45 pct Co. The tailings contained 67.2 pct of the nickel and cobalt and 15.9 pct of the copper originally in the copper concentrate; the remainder of the values reported to the flotation concentrate, which analyzed 29.6 pct Cu. To verify the laboratory flotation results, a 60 kg/hr process demonstration unit (PDU) was constructed in the Cominco American Magmont mill, Bixby, Mo.

Jan 1, 1978

By Joseph A. DeCarlo

This information circular presents data for 1960 on individual coke plants in the United States. All oven-coke plants in existence, whether active or idle at the close of the year, are listed in this report. With two exceptions, only beehive plants on which reports were submitted to the Bureau of Mines are included. Although the Bureau was unable to obtain reports from these two active plants in 1960, the number of ovens and annual coke capacity are estimates, based on previous reports filed with the Bureau of Mines. Accordingly, there were 73 oven-coke plants in existence at the end of 1960 of which 70 were active. Reports were received on 44 beehive plants of which only 13 were in operation at year end. Oven-coke plants are listed alphabetically by States in table 1 which shows the name and address of the company, location of plant, classification or type of ownership, number and type of ovens, annual coke capacity, and coal-chemical materials produced. The terms "furnace" and "merchant" plants used in this and all other reports of the Bureau of Mines designate the type of ownership. Furnace plants are those owned by iron and steel companies whose main business is production of coke for use in their own blast furnaces. Merchant plants are those associated with chemical companies, gas utilities, as well as those that produce for sale on the open market metallurgical, industrial, and residential-heating grades of coke and coal-chemical materials. The annual coke capacity shown for each plant in this table is based on the minimum coking time necessary to produce coke with qualities suitable for its intended use. Therefore, the annual capacity of a plant may change from year to year, depending on age and condition of ovens, the character and quality of coal carbonized, the grade of coke required, and other factors. For example, annual coke capacity of a coke plant primarily making foundry coke with longer coking cycles would be lower than one making blast-furnace coke. Also some ovens must be operated at slightly lower than normal flue temperature because of the condition of the refractories and maximum capacity would be somewhat lower than designed capacity. For this reason, the capacity reported to the Bureau of Mines may differ from the designed or rated capacity estimated by the coke-oven builders at the time of construction. For example, if the generally accepted standard coking rate of one inch per hour were used on all ovens to calculate total annual capacity, it would have been 80.4 million tons or 2 percent higher than the capacity reported to the Bureau. Because of the factors mentioned above, the annual coke capacity shown in this table is believed to be a reliable measure of the practical operating capacity of the industry.

Jan 1, 1961

By M. M. Tilman

The Bureau of Mines conducted research to determine whether it is possible to substantially improve the fatigue resistance of lead sheet by means of surface coatings. Five types of coatings were applied to unalloyed chemical lead sheet. Flexural tests revealed that the best fatigue resistance was obtained with coatings of vacuum grease. Vacuum-grease coatings on unalloyed lead sheet resulted in fatigue resistance at least as good as that of the fatigue-resistant alloy Pb-0.04 Ca. Coated lead sheet was also tested in short-time tensile tests and in tensile creep tests. Tensile and yield strengths were increased by several of the coatings with only moderate loss of ductility. Creep resistance was also improved in varying degrees by most of the coatings. The Bureau also conducted research on the effectiveness of noise barriers by using sheet lead in combination with other materials. Noise barriers consisting of continuous-cast sheet lead with gypsum board were found to be effective and relatively inexpensive barriers.

Jan 1, 1978

By Bryan F. Ulrich

If resin-grouted roof bolts are not installed correctly, mine roof reinforcement can be affected, and roof falls can result. A bolt installation variable that is readily controlled by the mine operator is annulus thickness. The objective of this U. S. Bureau of Mines investigation was to study the effect of annulus thickness variations on the integrity of 3/4-in-diam resin-grouted bolts. Forged-head test bolts, 2 and 1 ft long, were installed in concrete blocks that had been drilled with 1-, 1-1/8-, 1-1/4-, 1-3/8-, and 1-1/2-in-diam bits. Standard pull tests were performed; then the concrete was broken away from the bolts so that grout mix quality could be inspected. It was found that the optimum annulus thickness is 1/8-in (l-in-diam drill hole), and as annulus thickness increases from the optimum, there is a corresponding decrease in grout mix quality, effective grout ratio, and axial stiffness.

Jan 1, 1989

By Bob Thomas, Syd Peng, Quanzhong Gu, Gene Wilson, Gerald L. Finfinger

Identifying the properties of overlying rocks in underground mining operations is important to ensure the appropriate roof support design is used to maintain stability of the mine entries. Recently J. H. Fletcher & Co. developed a monitoring and control system for roof bolters for the underground mining industry. The system records the drilling parameters used during roof bolt drilling and the information can provide insight into the physical properties of the roof strata. The parameters include thrust, rotational speed, torque and velocity and the measurements are collected every 0.1 second during the operation. The drilling parameters were analyzed to determine the application of identifying the strength of rocks being drilled from the measurements. The data was converted into the specific energy of drilling which is a measure of the amount of energy required for removing a given unit of rock during a drilling operation. The laboratory studies completed to date indicate a fairly high correlation between the specific energy of drilling and the unconfined compressive strength of :he rocks that were drilled. Additionally, the drilling parameters were shown to be effective for identifying the presence of fractures or bed separations between rock layers. The thrust, torque and specific energy of drilling were all good indicators for identifying the fractures or separations. Regardless of the drilling parameters used during the drilling experiments, the location of the fractures were identified. In order to determine the application of the drilling parameters for identifying roof rock properties, two series of experiments were conducted. The first series of experiments used three "manufactured" roof layers that had various rock samples embedded in concrete blocks. The rock samples included three types of sandstone, marble, and argillite. Another concrete block was poured with foam inserts to simulate large bedding separations (2 to 8-in). Two other manufactured blocks were constructed using high-strength concrete with cardboard layers embedded to simulate smaller fractures or bedding separations. The size of the cardboard layers varied from 1/8- to 1-in thick. One of the blocks had the cardboard layers embedded at an inclined angle to determine the effect of the orientation on the drilling parameters. A series of experiments was conducted with the rotational speed and the penetration rate held constant and the thrust and torque allowed to vary. The information collected from the experiments is used to determine the application of the drilling parameter measurements for identifying rock properties, fractures and bedding separations.

This chapter presents data on occupational exposures from several sources. Data from compliance samples obtained by MSHA inspectors are presented in table 6-1 for coal mine dust and silica dust, and in tables 6-2 through 6-6 for metal fumes. Since these samples were taken for compliance monitoring rather than as part of a survey of the industry, it is difficult to predict how well they indicate actual exposures for all mining operations. In the coal industry, 7.8% of all respirable dust samples during 1986-1995 were above the permissible exposure limit (PEL). Of silica dust samples obtained during the 10-year period, 23.7% were above the PEL in coal, 16% in metal, 10.8% in nonmetal, 9.1% in stone, and 7.6% in sand and gravel. Of metal fume samples, silver samples showed the largest percentage above the PEL-approximately 48% of samples in both metal and nonmetal. Tables 6-7 and 6-8 present data on noise exposures from the MSHA "dual threshold" survey, which was published in the Federal Register [61 Fed. Reg. 66347 (1996)] as part of a proposed rule change for occupational noise exposure in mining. This study examined a group of samples obtained during 1991-1995 and compared the percent of samples that were above two separate specified limits. The first limit was the current noise standard, a time-weighted average of 90 dBA, calculated to include only exposures at 90 dBA and above. The second limit was a time-weighted average of 85 dBA, calculated to include exposures at 80 dBA and above. Tables 6-8 and 6-9 refer to musculoskeletal overload conditions examined in the National Occupational Health Survey of Mining (NOHSM) [NIOSH 1996]. Table 6-8 shows the operational definitions for each condition; table 6-9 shows the percentage of the workforce potentially exposed, by commodity. Across all commodities, a large proportion of workers were exposed to musculoskeletal overloads due to positioning of the neck and back; positioning and motion of the forearms, arms, and shoulders; heavy lifting; and positioning and movement of the lower limbs. The recorded overloads were defined in the survey and did not exceed any NIOSH, MSHA, or OSHA guidelines for musculoskeletal overloads. Further information on this survey appears in appendix A.

Jan 5, 2000

By Dorsey A. Lyon, Robert M. Keeney

This bulletin is one of a series dealing with the application of the electric furnace to the smelting of ores and the manufacture of alloys, and is published by the Bureau of Mines in the endeavor to increase efficiency in metallurgical processes. The bulletin presents, first, a critical discussion of the possibility of smelting copper ores in the electric furnace; second, the results of the experimental work of other investigators on the electric smelting of copper; third, the results of experiments by the authors on the electric smelting of native copper concentrates and sulphide copper ores; and, fourth, a comparison of the electric furnace with the blast furnace and reverberatory furnace for copper smelting. Before considering the electric smelting of copper ores the reader should understand that the electric furnace was not developed as a competitor of the combustion furnace, but for the purpose of doing high-temperature work that can not be done in the combustion furnace, and for the treatment of ores from deposits that are in regions where fuel is scarce and costly but hydroelectric power is comparatively cheap, as in Chile, and in certain parts of Canada, the United States, and Mexico. Furthermore, it is not the object of this report to try to prove that the electric furnace should replace the reverberatory or the blast furnace, as used at present in smelting copper ores, but to show that the electric furnace may be used with advantage in localities where conditions are not favorable to the use of the reverberatory or the blast furnace. For example, otherwise valuable ore deposits may be situated in a district so remote from, or inaccessible by, railway that the cost of get- ting coke for smelting, or of transporting the ore to a smelter, is pro- hibitive. If there is sufficient water power at hand, from which electric power can be developed at a reasonable cost, and this electric power is used for smelting the ore in an electric furnace, with subse- quent bessemerizing, if necessary, the concentrated product may be

Jan 1, 1915

By Richard Mainiero, James H. Rowland

For many years there have been small scale tests available for evaluating the toxic fumes production by cap-sensitive explosives (DOT Class 1.1), but these could not be used with blasting agents due to the large charge sizes and heavy confinement required for proper detonation. Considering the extensive use of blasting agent in construction and mining, there is a need to determine the quantities of toxic fumes generated by blasting agents. At the International Society of Explosive Engineers Twenty Third Annual Conference on Explosives and Blasting Technique in 1997, the authors reported on a facility for detonating large (4.54 kg), confined blasting agent charges in a controlled volume that had been constructed at the National Institute for Occupational Safety and Health’s Pittsburgh Research Lab’s Experimental Mine. Since 1997, this facility has been used to collect data on toxic fumes produced by the detonation of various ammonium nitrate/fuel oil (ANFO) mixtures and several cap-sensitive explosives. ANFO composition ranging from 1 to 10 percent (pct) fuel oil have been studied. As expected from previous studies, with an increase in fuel oil content the carbon monoxide production increases, while nitric oxide and nitrogen dioxide production decrease. The detonation velocity varies from 3,000 to 4,000 m/sec for the 1to 10 pct range of fuel oil content, suggesting that ANFO mixes with improper fuel oil content may appear to detonate properly, while their fume production differs significantly from optimum. The study also considers such factors as degree of confinement, water contamination, and aluminum content on blasting agent fume production. Results indicate that water contamination of the ANFO has little effect on carbon monoxide production, but causes significant increase in nitric oxide and nitrogen dioxide production. Decreasing confinement from Schedule 80 steel pipe to 0.4-mm thick sheet metal also has little effect on carbon monoxide production, but significantly increases nitric oxide and nitrogen dioxide production. Adding5 and 10 pct aluminum to the ANFO had no clear effect on carbon monoxide, nitric oxide, or nitrogen dioxide production.

By W. E. Anable

A 180° magnetic deflection residual gas analyzer mass spectrometer with a mass range of 2 to 200 amu was used to study the nature of gases evolved during arc and electron-beam melting of certain reactive and refractory metals. The partial pressure of residual gases over molten Mo, Hf, Ti, and Fe, was found to be similar: Water and hydrogen were evolved from the samples and from the furnace components, carbon dioxide and carbon monoxide resulted from deoxidation of some of the melts. Argon and acetone were residuals in the system, and methane was a decomposed organic compound from the oil diffusion pump.

Jan 1, 1969

Reduce the noise radiated by the auger miner cutting head (typically 105 dBA at the face) by 10 dBA without compromising the durability or productivity of the tool. Approach Research was conducted by the Bureau of Mines to identify the noise sources of auger miners with emphasis on the cutting head and coal cutting process. The overall noise level generated by the coal cutting process was found to depend greatly upon the structural characteristics of the auger cutting head. Based on this information, a quieter cutting head was

Jan 1, 1982

By Richard J. Bielicki

Poor mixing of methane and air at coal mine working faces causes fluctuating methane concentrations. If these fluctuations are large enough, methane levels can periodically exceed safe limits, even though the time average methane concentration may be satisfactory. Concentration fluctuations measured underground can result both from variations in methane emission rate and poor mixing. The present paper reports on a statistical analysis of fluctuations at a constant methane emission rate, that is, on fluctuations due only to poor mixing. A full-scale model of a working face was used. Both peak heights and elapsed times between peaks were evaluated. Good mixing was indicated by normal, Poisson, and exponential distributions while poor or incomplete mixing was indicated by log-normal or gamma distributions.

Jan 1, 1974

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

Appendix B - Mine Evacuation Simulation Program - User&apos;s Manual B 1 Introduction Appendix B documents information necessary to use the emergency escape simulation program and to make modifications if necessary. For a user interested in using the program as it exists, Sections B 2, B 5 and B 6 are particularly useful. The program listing (B.6) can be used to prepare a card deck and the data cards can be punched from the directions given in Section B. 2. Typical input data and output printout summarized in B 5 provides guidelines for the program use. Sections B 3 (Program Nomenclature) and B 4 (Subroutine Description) describe, in detail, the inner workings of the program and are particularly useful for a user interested in modifying the program.

Jan 1, 1976

By Ann G. Kim

The Bureau of Mines investigated factors that influence the formation of methane and other hydrocarbon gases in coal, which is an integral part of the coalification process. Coalification begins with a biogenetic stage in which plant debris decomposes and peat is formed; methane and CO2 are the predominant gases produced during this stage. During the diagenetic stage of coalification hydrogen and the hydrocarbon gases methane, ethane, ethylene, propane, propylene, butene, iso-and normal butane, and pentane are formed by dissociation of the organic material. Methane may also be produced by a secondary reaction of hydrogen with unsaturates or by the reduction of CO2. The gas contained in coalbeds is a mixture of methane, C2 through C5 alkanes, CO2, O2, N2, H2, and He; its heating value is equivalent to that of natural gas. The gas content of coal depends on many variables, but an empirical relationship between adsorptive capacity, rank, and depth has been observed.

Jan 1, 1978

By Donald O. Capstick

A mineral survey of a 13,525-acre portion of the 21,875-acre Owyhee Canyon Wilderness Study Area in northern Nevada was conducted by the U.S. Bureau of Mines in 1984. Two samples from sand and gravel deposits in the study area contained minor placer gold typical of the Owyhee River area. The gold-bearing gravels are too low grade or of insufficient volume to support commercial placer mining operations. The sand and gravel deposits might have minor local construction uses.

Jan 1, 1986

By Kevin Michael, David C. Byrne

In previous issue of Spectrum (October 1999, 16/4), a system of measuring the attenuation provided by insert-type hearing protectors was described, That report described experiences using the FitCheck (Michael & Associates, Inc.) system in a pilot project involving the steel industry during 1998.[ ]