Search Documents

Avoid accidents that can occur when applying belt dressing from an aerosol can, particularly when can pressure has dropped or when spraying against wind. Approach Use a garde-type sprayer. How It Works Commercially available garden-type sprayers can be used for applying conveyor belt dressing from 12 feet away, or more. Pressure is easily raised and maintained at about 50 psi. Most sprayers have a hand pump, but a battery-powered cordless model is also available. Garden-type sprayers are available in various sizes from 11/2 to 18 gallons, with the larger models wheel mounted. The 3-gallon model evaluated by the Bureau has a shoulder carrying strap, which gives additional safety advantages. Use of the strap frees both hands for climbing ladders or holding onto catwalk rails. When spraying, one hand can remain on a handhold to lessen the chances of touching a moving belt.

Jan 1, 1980

By E. J. Kloos

Bureau of Mines-approved self-contained breathing apparatus of the compressed air demand type were evaluated for performance at low temperature. Apparatus durations, breathing resistances, and airflow rates were measured on machine tests at room temperature and -25° F. Man tests under actual wearing conditions verified the machine test results. Many serious functional changes in apparatus performance occurred at low temperature. Pressure regulators malfunctioned when diaphragms lost flexibility. Under certain conditions frozen condensed moisture sealed exhalation valves and fogged eyepieces. High-pressure leaks, not encountered at ordinary temperature, developed at low temperature. Tests results are discussed generally and specifically for each apparatus. Recommendations are given to obtain optimum performance from demand type breathing apparatus at low temperatures.

Jan 1, 1968

By M. M. Tilman

The Bureau of Mines investigated the precipitation strengthening of lead¬-base alloys containing 0.5 through 4 weight-percent combined Cd plus Sb. The Cd and Sb were alloyed in a 1-to-1 atomic ratio which maintained compositions along the quasi-binary section Pb-CdSb. Tensile properties, creep rates, and stress-rupture values were obtained on alloys in the aged condition. The highest tensile strength was observed in an alloy of Pb-3 CdSb, After aging for 6 months at 90°±3° F, this alloy had a mean tensile strength of 8,950 psi with 15-percent elongation. An aged alloy of Pb-1 CdSb exhibited a steady state creep rate of 1.2 X 10-3 percent per day at a stress of 500 psi and a temperature of 90°±3° F. Times to rupture at stresses up to 4,000 psi and at a temperature of 90°±3° F were obtained for some compositions.

Jan 1, 1970

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

2, Survey of Representative Group of Metal and Non-mental Mines Before proceeding to develop and analyze Emergency Escape System Guidelines, it was necessary to obtain a broad range of information, including both fact and opinion. Although there were many areas to consider, the surveys had three primary goals 1. To determine the current state of underground escapeway planning and execution in American, metal and non-metal mines. 2. To determine, for a wide range of mining conditions, what difficulties can be encountered in complying with present and proposed escapeway regulatory standards. 3. To determine what improvements could be made and what equipment and technology was available to aid in implementing these improvements. To accomplish these goals, three major surveys were undertaken¬ 1. Survey of MESA and State Mining officials, discussed in Section 2. 1. 2. Survey of representative U S metal and non-metal mines, discussed in Section 2. 2. 3. Survey of manufacturers supplying equipment, primarily hoisting, suitable for use in escape systems, the product information which was obtained is discussed in Section 7.

Jan 1, 1976

By Forrest T. Moyer

The safety record of the mineral and mineral-fuel mining and processing industries in 1965 was improved slightly, as indicated by the reduced injury-frequency and severity rates. The overall operating activity was higher in 1965 as measured by the gains in the number of men working and in the total man-hours of worktime. Injury Experience.-The rate of occurrence of all disabling work injuries in the mineral industries was 17.65 per million man-hours in 1965. This overall rate comprised frequencies of 0.28 for fatal and 17.37 for nonfatal work injuries, of which both were slightly better than the corresponding rates of 0.29 and 17.53 in 1964. Fatalities totaled 537; 5 less than in 1964. However, the total of 32,982 nonfatal injuries was 575 higher than in 1964. This larger number of nonfatal disabilities was offset by the increased worktime so that the nonfatal frequency rate decreased in 1965.

Jan 1, 1967

By C. M. Flynn

The Bureau of Mines prepared and investigated xanthated sawdust adsorbents to determine their effectiveness in removing heavy metal ions from dilute aqueous solutions, mine-drainage waters, and brines. Stripping of the metal values from the metal-laden adsorbent was also investigated. The treated sawdusts had an adsorption capacity of 0.3 to 0.4 meg/g dry adsorbent for Mn, Co, Ni, Cu, Ag, Zn, Cd, Hg, or Pb from feed solutions with pH 5 to 6. The feed solutions tested included mine-drainage waters and geothermal brine. Effluent metal concentrations as low as 0.05 to 0.1 mg/l were obtained at effluent pH values of 6 to 9. The order of affinity of metals for the sawdust adsorbent is Na«Ca~Mg~Mn<Zn<Ni<Cd<Pb~Cu. The presence of Ca, Mg, or Na in concentrations as high as 2 g/l does not seriously impair the heavy-metal adsorption. Metals were desorbed from the metal-laden adsorbent by elution with dilute mineral acids, sodium cyanide, or salts of ethylenediaminetetra-acetic acid.

Jan 1, 1979

Compare the fire endurance of paneled steel stoppings with that of traditional concrete block Stoppings. Background Permanent stoppings or partitions arc used in mines to separate ventilation airways. The ability of stoppings to retain their structural integrity for a minimum length of time under lire conditions and prevent the spread of flame and toxic combustion products to an adjacent airway is critical. The success of miners in reaching safety during a fire depends largely on the presence of uncontaminated airways. Traditionally, permanent stoppings for coal mines are constructed of concrete blocks. Recently, paneled steel stoppings that satisfy many of the requirements demanded of permanent stoppings, such as incombustibility and strength, have been introduced. Their use also introduced concerns such as the ability of a steel stopping to maintain its ventilation control function when exposed to a fire and the potential that the fire could transmit enough heat through the stopping to ignite combustible materials on the unexposed side. To address these concerns, the Bureau of Mines investigated the fire endurance of galvanized steel and concrete block stoppings.

Jan 1, 1989

Measure the leakage through individual crosscut stoppings quickly and economically so that the worst ones can be identified and repaired. (Typically 60 to 80% of the air supplied to a mine short circuits before reaching a working face.) Approach Most of the leakage through a permanent stop-ping is channeled through two windows in a temporary stopping, and air velocities through the windows are measured; leakage is determined from a formula. How It Works A temporary stopping made of plastic brattice is erected in the same cross cut as the permanent stopping, either upstream or downstream. The brattice is fastened to the roof, bottom, and ribs of the entry with spads. Normal leakage of brattice was allowed for in deriving formula, and does not effect results. For best accuracy the brattice and the stopping should be separated by a distance of one hydraulic diameter.

Jan 1, 1979

By W. Blake, J. K. Whyatt, T. J. Williams

Researchers at the U.S. Bureau of Mines collected and analyzed over core measurements and other indicators of in situ stress characteristics at the Lucky Friday Mine, Mullan, ID. An analysis of these data revealed that significant local variations in in situ stress are present in this mine and that these variations existed prior to mining. High stresses were found to be associated with the most competent strata and a locked section of a fault. An estimate of the predominant stress field was developed for mine-wide modeling. The estimate shows that the greatest principal stress was oriented north of northwest. This information should provide a basis for mine-wide structural modeling of the Lucky Friday Mine and should generate important insights into localized stress conditions, which may significantly affect both local and mine-to-mine variations in seismicity induced by excavation.

Jan 1, 1995

Determine the extent of upper extremity cumulative trauma disorders (UECTD&apos;s) in the U.S. mining industry. Background UECTD&apos;s are injuries that develop gradually over a period of time as a result of repeated stress to a particular body part without adequate time between stresses for full recovery to occur. The stresses that contribute to UECTD&apos;s may occur because of the following work components: awkward position of wrist or arm, excessive manual force, high repetitions of manual movement and effort, cold environment, and vibration. Cumulative trauma injuries to the arm and hand have become an ever growing concern among safety and health professionals in a number of different industries and work settings, such as meatpacking operations, assembly-line work, and keyboarding. Mine workers arc also exposed to a combination of stressors and work design deficiencies that result in arm and hand injuries. For example, certain job tasks and environments, such as that of an underground jackleg driller, expose miners to segmental (hand-arm) vibration and cold temperatures. Operators of underground mobile equipment, such as scoops and trams, regularly have their hands in direct contact with vibrating levers and controls.

Jan 1, 1992

By T. F. Tomb

This paper describes field and laboratory investigations conducted on a dust-collection system recently designed for integral use with a continuous mining machine. The results of the field study showed that the average respirable dust concentration measured at the machine operator&apos;s position was reduced by about 60 percent (from 8.7 to 3.5 milligrams per cubic meter), and total and respirable dust concentrations in the return air were reduced by approximately 70 percent. The data indicated that approximately 20 percent of the dust generated at the face was not passed through the scrubber. The lab-oratory results showed that the overall efficiency (by particle count) was approximately 80 percent for total dust concentrations (minus 20 micrometers in size) typical of those encountered underground. Calculations based on total dust concentrations measured during the underground study indicated that the respirable mass concentrations of the effluent from the scrubber would still exceed acceptable levels even if scrubbing of all the air at the face were possible.

Jan 1, 1973

By W. F. Marshall

The effect of engine parameters on exhaust emissions from two diesel engines was studied experimentally. Fuel-injection characteristics and intake air conditions were considered as parameters influencing the emissions. Emphasis was placed on the effect of parameter variations on nitrogen oxide (NOx) emissions, because diesels generally emit very low levels of carbon monoxide (CO) and unburned hydrocarbons. Emissions other than NOx were at lowest levels when the engines were adjusted for best performance. NOx emissions can be diminished somewhat through variation in fuel-injection characteristics, but there generally are penalties in emissions of CO, smoke, and unburned hydrocarbons or in engine performance. Temperature and composition of intake air have a significant effect on NOx emissions. Levels of NOx are reduced by recirculating the exhaust gas or by adding water to the intake air stream. However, the rate of water added or exhaust gas recirculated must be limited to prevent the degradation of engine performance and increased emissions of CO and smoke. At high exhaust recirculation rates, levels of CO and smoke were increased such that it was necessary to derate the engine and also to use a catalytic system for oxidation of CO.

Jan 1, 1971

By A. F. Colombo

Infrared spectroscopy employing attenuated total reflectance (ATR) techniques on thin films of dried gelatinized starch solution was used during Bureau of Mines research to determine the structural and impurity differences in starch products and to correlate these characteristics with the flotation response of a nonmagnetic taconite. All of the starch products evaluated gave spectrograms which were characteristic of the anhydroglucose monomer and its polymerization product. Distinct infrared absorption peaks caused by the protein molecule were observed and were used to classify the starches. Correlation of laboratory flotation of calcium-activated gangue from a Mesabi Range nonmagnetic taconite and infrared spectra produced from gelatinized starches showed that protein impurities and linear chain structure limited the effectiveness of starches as iron mineral depressants. Starch products having spectrograms similar to pure amylopectin were generally good depressants for iron oxides, were effective at about one-half the addition that was required for starches that gave infrared responses similar to pure amylose, and yielded acceptable iron concentrates containing 61.5 percent iron and 6.5 percent silica.

Jan 1, 1969

Reduce the number of conveyor-related accidents in the mining industry by providing recommendations for effective operation of conveyor belt cleaning systems. The Problem Troughed belt conveyors provide effective, and efficient materials transport and their use has increased throughout the mining industry. Carryback, the spillage that accumulates under the belt, is a problem even with belt cleaning systems installed. Mining personnel are exposed to safety and health hazard; as they attempt to clean up this spillage. Approach To investigate the influence of metal-segmented-blade belt cleaners on the amount of carryback spillage, the. Bureau identified and tested the following parameters: (1) amount of pressure applied to the cleaner blades, (2) friction between the blades and conveyor belt, and (3) wear rates of different metal blades. The test parameters were quantified by recording the amount of carryback material passing the metal cleaner blade, and the weight loss of the blades. The data collected were used to identify the following critic d operational parameters of a segmented-blade conveyor cleaner system: (1) the existence of an optimal operating pressure for the conveyor and cleaning systems and (2) elimination of recessed patterns on the working side of the conveyor belt.

Jan 1, 1989

Provide optimum visibility of mining operations while maintaining protection and comfort for machine operators. Approach A cab with hydraulically powered variable-height control was developed and used on a loading machine in underground operations. How It Works The cab is attached to the vehicle on a horizontal trunnion located near the forward end of the cab. A hydraulic cylinder, controlled by the operator from inside the cab, pivots the cab about the trunnion providing variations of up to 16 inches in elevation. The nominal tramming position of the cab is with its underside 6 inches above the mine bottom. From this position the cab can be pivoted up, or down, so that its back end is elevated 10 inches, or lowered to the floor. (See Figure 1.) The cab encloses the operator for protection against both overhead and lateral obstructions, and it raises or lowers, allowing the operator to select the most advantageous cab height. The cab is angled inboard 30 degrees to the machine line of direction. The operator&apos;s seat swivels to allow view of the conveyor during loading. All controls are located within the cab and move up and down with it.

Jan 1, 1978

By Jami M. Girard

INTRODUCTION Slope stability accidents are one of the leading causes of fatalities at U.S. surface mining operations. The Spokane Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) is currently conducting research to reduce the fatalities associated with slope failures and other unexpected failures of ground. The purpose of this paper is to introduce various warning signs of slope instability so operators are better able to recognize hazards. The most common slope monitoring equipment and practical methods of installation are discussed as well as the limitations of these systems. CONSEQUENCES OF SLOPE FAILURES Unexpected movement of ground causes the potential to endanger lives, demolish equipment, or destroy property. Between 1995 and 2001 (2nd quarter), 34 fatalities were caused by ground instability. This accounts for approximately 15% of all surface mine fatalities (Figure 1). These figures include fatalities classified by the Mine Safety and Health Administration (MSHA) as “fall of face or highwall,” “powered haulage,” “equipment,” and other MSHA accident categories, where the primary cause of the accident was unanticipated movement of the ground. This includes fatalities resulting from bench and highwall failures, rock falls, waste dump and stockpile failures, and the collapse of unknown underground workings. [ ]

By F. N. Kissell

The Bureau of Mines used sulfur hexafluoride (SF6) tracer gas to evaluate the effectiveness of gob ventilation and/or sealing practices at three coal mines, each having different problems associated with their mined-out areas. The purpose of these ventilation studies was to better understand whether current techniques employed for ventilation or sealing are successful at minimizing the potential for gob fires and explosions. The work performed at each mine is discussed: One is a long-wall operation that uses ventilation to carry off hazardous gases, and two are room-and-pillar operations, each with far different concerns, that seal off the gobs to isolate them from the main mine ventilation. In all cases employment of the Bureau&apos;s SF6 tracer gas technique resulted in answers to questions raised by the mine operators concerning the effectiveness of their gob ventilation or sealing practices in preventing mine fires.

Jan 1, 1986

By Maria I. De Rosa

Table 55 and figure 19 show the number of fires and fire injuries for stone mills by state during 1990-2001. Table 55 also shows the injury risk rates, employees&apos; working hours, and lost workdays. In all, 118 fires occurred in 33 states. Seventy-six of the fires caused 82 injuries (including 8 fires and 6 injuries involving contractors). The yearly average was 9.8 fires and 6.8 injuries. The Ewhr value was 873 x 106 hr (In = 0.019), and the LWD value was 1,911. Missouri had the most fires (16 fires and 9 injuries), followed by Pennsylvania (15 fires and 14 injuries), Michigan (9 fires and 5 injuries), and Virginia (7 fires and 5 injuries). Of these states, Virginia had the highest injury risk rate value (In = 0.09 1). Table 56, partly illustrated in figure 20, shows the number of fires, fire injuries, risk rates, employees&apos; working hours, and lost workdays by time period. The number of fires and fire injuries decreased during most of the periods, with a sharp increase during the last period. The number of employees&apos; working hours increased throughout the periods. The In values follow patterns similar to those shown by the injury values. Tables 57-63 show the number of fires by ignition source, method of detection and suppression, equipment involved, location, and burning material by time period. Figure 21 shows the major variables related to fires for 1990-2001. Table 63 shows the fire injuries per number of fires causing injuries and total fires by year, ignition source, equipment involved, and location.

Jan 1, 2004

By J. C. Edwards

The Bureau of Mines developed a mathematical model that decribes the interaction of an automated breathing and metabolic simulator, or lung, with a self-contained· self-rescuer that is supplied compressed oxygen. The model can be used to predict the gas partial volumes of 0z, Nz, and COz in the lung and in the self-rescuer breathing bag for a prescribed metabolic state that characterizes the lung. Nonlinear rate equations are used to describe the temporal evolution of the gas partial volumes. A numerical procedure was established with a FORTRAN computer program to solve these equations, which correspond to a given metabolic state. Examples are presented of applications of the model to predict bag volume and bag oxygen concentration changes with time when the bag is controlled by an automated breathing simulator. Under certain restrictive conditions, the model equations can also be used to analytically pre-dict the time required for the bag to reach a maximum or minimum volume. The model equation in this latter case was extended to transi-tions between metabolic states, with transitions described as exponential growth or decay processes.

Jan 1, 1985

To prevent injury to miners caused by violent whipping of mining machine trailing cables. Approach: The hydraulic cable controls are adjusted to reduce whip by visual reference of the cable sag to the height of the cable guide. How It Works: The cable sag is adjusted by visually estimating its height above the ground, at a specific reference distance behind the machine. This reference distance is measured horizontally back from the point where the cable leaves the cable guide. The Reference distance is 2H where H equals the height of the cable guide above the floor. See Figure 1. Cable sag should be less during rewinding than during unwinding. During cable unwinding, the cable height (at the refer¬ence distance) should equal 1/31-1. During rewinding, the cable height should equal ½ H. Field tests were made on several manufacturers&apos; equipment after adjusting cable sag as above. Cable whip was greatly reduced for all, and whip was almost eliminated on a shuttle car equipped with a Joy Manufacturing Company 500108-104 cable reef and the newer (nonporous) shuttle valve. The following directions are for adjusting cable sag on a shuttle car equipped with a Joy Manufacturing Company 500108-104 Cable Reel equipped with the newer shuttle valve. Cable sag can be adjusted on machines equipped with other cable reels and valves by referring to the manufacturer&apos;s manual and making the appropriate cable valve adjustments.

Jan 1, 1976