Search Documents

By K. K. Kelley

"In an earlier consideration of the vapor pressure of iron 3/ it was found necessary to estimate the specific heat of gaseous iron to write satisfactory free-energy-of-vaporization equations for the several forms of iron. That the specific heat of gaseous iron will exceed greatly the classical value of Cp = 4.967 calories per gram-mole per degree is evident from even a cursory Lamination of its spectrum. The two lowest energy states are separated by only 416 cm-1, which is small enough so that the second state is effective, theoretically, at below room temperature. Such phenomena are by no means uncommon, but, while they have been recognized with substances that ordinarily are encountered as gases, classical gaseous specific--heat values still are used, often without question, for the vapors of metals and other elements that are solids under ordinary conditions. The following calculations for iron and copper gases are presented to illustrate the sort of deviations from classical values that are encountered with metal gases.The methods employed in calculating from spectroscopic data of thermodynamic quantities such as specific heat, entropy, and free energy have been described, in detail by Giauque 4/ and others. These will be briefly reviewed here. It is customary to separate the translational energy of a molecule from the rotational, vibrational, and electronic energies. In the case of monatomic gases, only translational and electronic Energies are involved. The classical expression for the specific heat of a mona¬tomic gas, Cp = 4.967, deals only with energy stored in the molecule as translational energy and consequently is valid only in temperature ranges in which no appreciable number of molecules undergoes a change in electronic state."

May 1, 1937

By Robert L. Lagace

The attention of this group was focussed on four through-the-earth communication systems that are presently of high interest to the U.S. Bureau of Mines; four systems for providing operational/emergency communications on the working sections of coal mines, indeed up to the very face of the section. The systems are: uplink-data, downlink-voice, sidelink-call alert coded page, sidelink-roof bolt voice page. Each of these systems makes use of the mine overburden as the signal transmission medium, as opposed to the guiding wires, cables, and tunnels treated by the operational communications working group. Each of these systems satisfies one or more of the Bureau's objectives for mine communications systems; namely • reliable links for monitoring the mine environment under both operational and emergency conditions. • reliable links for communicating with miners during emergencies. • special links for increasing the efficiency of day-to-day operations of the mine. Each of these systems has been successfully demonstrated on a limited experimental basis, and prototypes of all these systems are installed and operating in the USBM experimental mine in Bruceton, Pa. Each of these systems must now be optimized regarding its performance, and engineered for practical routine application to the working sections of actual operating coal mines, particularly those of the room and pillar type. This optimization and engineering must take place subject to the principal constraints listed by Howard E. Parkinson in his Workshop paper entitled, "Objectives and Constraints of Through-the-Earth Electromagnetic Communications Systems'' and enumerated below. • Depth of Mine Overburden • Overburden Conductivity • Electromagnetic Noise In and Above Mines • Limited In-Mine Electrical Energy (Stationary or Man Carried) During an Emergency • Intrinsic Safety for In-Mine Equipment • Practical and Rugged Equipment for Use Under Both operational/Emergency conditions • Severe Weight Limitations for Man Carried Equipment • Reasonably Low Costs Especially for Man Carried Equipment Part II of this paper provides a brief description of each system, while Part III summarizes the present status of developments related to these systems and some recommendations for future work needed to advance these systems to the practical application stage.

Jan 1, 1973

By Ivette E. Torres

For a study such as this, which summarizes and amalgamates much information collected, compiled, and utilized by the numerous U.S. Bureau of Mines country specialists and branch chiefs for inclusion in their country and regional reports that comprise the five other sections of 1992 Minerals Yearbook-International Review, it is clearly impossible to cite all sources of information used in its presentation, but some recognition is due. Generally speaking, this study and its related detailed studies on countries and areas would be much more difficult, if not impossible to complete, without the efforts of the personnel of our counterpart national mining and geological agencies throughout the world. Information that they collect, compile, and then publish, either in their own volumes or those of central statistical agencies in their countries, are the foundations on which this work rests. Thus, our appreciation is expressed to the multitude of persons employed by these agencies for their contributions.

Jan 1, 1994

By Joseph S. Coffman

The Bureau of Mines investigated the availability of barite (BaSO4) from 35 U.S. and 41 non-U.S. mines and deposits in 17 market economy countries (MEC's). This evaluation assesses the availability of mud-grade barite, and concentrates consumed by the chemicals and fillers industries. The demonstrated resources defined in this analysis totaled 130 million metric tons (Mmt) of barite (contained BaSO4), yielding a potential 115 Mmt of recoverable barite concentrates. At the 1984 MEC production rate, the evaluated resources would last about 30 yr; however, this would include production costs of up to $100/mt concentrate. An average price needed to cover all costs of production over the life of each operation was determined for both mud-grade and chemical- and filler-grade barite products. Including a 0-pct discounted-cash-flow rate of return (DCFROR), regional weighted- average total production cost ranged from $38/mt for barite concentrates in Asia to $71/mt for U.S. operations. Transportation costs have the greatest impact, contributing up to 60 pct of the total cost of production. Rail transportation costs from the mines to U.S. markets are generally significantly higher than ocean shipping rates on imports.

Jan 1, 1986

By V. R. Spironello

Operating variables affecting the efficiency of the basic oxygen furnace (BOF) and the level of contaminating elements in the steel product were investigated by the Bureau of Mines. Steel was made in a 400-lb-capacity BOF designed to rotate on its vertical axis to increase the area of hot metal surface subject to oxygen attack. Hot metal for the BOF was made by melting pig iron and scrap in an 18-inch (ID) cupola. The variables were BOF speed of rotation, rate of oxygen flow, number of jets and angle at which they were machined into the oxygen-lance tip, temperature of hot metal, reactivity of lime, and temperature of scrap for the BOF charge. Experiments were arranged according to a two-level fractional-factorial design. The effects of the seven variables were evaluated for 13 responses. The greatest ingot yield occurred while using the larger angle lance tip and jets. The most carbon burned per unit volume of oxygen resulted from rotating the BOF and using the smaller angle lance tip. The largest sulfur transfer to the slag occurred at the higher hot metal temperature levels and higher rate of oxygen flow.

Jan 1, 1970

By Annie G. Smelley

The Bureau of Mines, U.S. Department of the Interior, as part of its mission to effect pollution abatement, conducted research to devise means for disposing of phosphatic clay wastes and reclaiming mined land. Part of the investigation was performed in a cooperative research project with 10 phosphate companies in Florida. The colloidal properties of the phosphatic clay suspensions, called slimes, make them difficult to dewater and dispose of without impoundment storage aboveground. Various reagents to flocculate and dewater these plant wastes were evaluated, and a polyethylene oxide polymer was found to function in a specialized flocculation dewatering technique. The flocculation dewatering method was investigated in bench-scale batch tests and applied in continuous dewatering tests using standard mineral-processing equipment. In continuous tests at feed rates of up to 58 liters per minute, wastes at 4 percent solids were dewatered to about 20 percent solids. About 0.8 kilogram of polymer was used for each metric ton of dry waste clay solids; processing time was about 4 minutes. Requirements for the treatment system are (1) proper mixing of the clay-waste feed and flocculant, (2) rapid removal of water as it is released, and (3) physical manipulation to promote cohesion of solids.

Jan 1, 1979

By C. C. Shale

Electrical resistivities for various coal ashes in air and in a nitrogen atmosphere are given over the range 100° to 1,500° F. Resistivity of low-carbon ash in air is very high at low temperature, rises to a maximum at about 250° F, decreases very rapidly with increasing temperature to about 800° F, then decreases gradually to approach an asymptote at 1,500° F. Resistivity of high-carbon ash in air follows this same general trend at values which are much lower and are proportional to the carbon content. After the carbon has been burned off, resistivity of the remaining ash approaches the high values corresponding to low-carbon ash of similar chemistry. Two factorial experiments show the effects of temperature, particle size, chemical content, and compressibility on the resistivities of four fly ashes of widely different chemical composition in the temperature range proposed for coal-fired turbines. Resistivities of all low-carbon ashes tested fall in the range 106 to 107 ohm cm at 1,500° F and should be removable by electrostatic precipitators. Ashes containing carbon in excess of about 8 percent, however, have low resistivity (as determined in nitrogen), especially at high temperatures. Therefore, high-carbon materials may not be collectable in precipitators because the resistivity is below the minimum value necessary for precipitation. Consequently, high carbon residues from partial combustion of coal probably could not be removed effectively at high temperatures.

Jan 1, 1968

By Leon E. Esparza

The Bureau of Mines studied 780 acres of the 24,130-acre Sheldon Contiguous Wilderness Study Area (CA-020-1012) in 1985. The study was done at the request of the Bureau of Land Management and authorized under the Federal Land Policy and Management Act (Public Law 94-579, October 21, 1 976) in order to evaluate the mineral resources. The study area is located in Washoe County, NV, about 35 miles northeast of Cedarville, CA. A search of county courthouse records and an examination by foot traverses through and adjacent to the study area did not reveal evidence of any mining or mining exploration activity past or present. In addition, evidence of any form of rock alteration was not observed. Evidence of mineral resources is not apparent. Although basalt, the only rock-type present in the study area, can have some limited industrial applications, sources closer to potential markets probably would preclude rock from this area being economically competitive. INTRODUCTION This report describes the USBM (U.S. Bureau of Mines) portion of a cooperative study with the USGS (U.S. Geological Survey) to evaluate mineral resources and potential of the Sheldon Contiguous study area at the request of the BLM (U.S. Bureau of Land Management). The USBM examines individual mines, prospects, claims, and mineralized zones, and evaluates identified mineral and energy resources. The USGS evaluates potential for undiscovered resources based on areal geological, geochemical, and geophysical surveys. Results of the investigations will be used to help determine the suitability of the study area for inclusion into the National Wilderness Preservation System. Although the immediate goal of this and other USBM mineral surveys ;s to provide data for President, Congress, government agencies, and the public for land-use decisions, the long-term objective is to ensure the Nation has an adequate and dependable supply of minerals at a reasonable cost.

Jan 1, 1986

By John C. Ferm

This report contains a summary of Phase I and complete results of Phase II portions of a study of geologic factors associated with roof falls in mines on the Pocahontas #3 coal seam in southern West Virginia and southwestern Virginia. Principal objectives of Phase I was the selection of five mines that best portrayed the spectrum of roof and mining conditions and Phase II consisted of a measurement and documentation program for each of the five mines. The documentation measurement program included reconnaissance mapping, detailed mapping, joint measurements and coring roof rock. 1.2 PHASE I RESULTS The results of Phase I consisted of the selection of the following five mines for detailed study: Virginia Pocahontas #3 (Island Creek Coal Company), Bishop (Consolidation Coal Company), Shannon Branch (Allied Chemical Company), Keystone II (Eastern Associated Coal Company) and Macalpine-East Gulf (Westmorelenad Coal Company). In addition, Phase I results, which were based on questionnaire data, indicated that the kind of rock in the roof --gray sandstone, crystallized sandstone, laminated sandstone and shale, grey shale, slickensided shale, and rider seams could be associated with good and bad top areas. Also presence of vertical separations, bolt length, entry and cross-cut width, length and torque on bolts and depth of overburden seemed to be related factors. These data provided a focus for the Phase II measurement program.

Jan 1, 1975

By James Paone

The Bureau of Mines conducted laboratory drillability studies on nine rock types using two mining-type percussive drills. Percussive-bit action was simulated by dropping a known weight on a rock sample to obtain a coefficient of rock strength for each rock drilled. While no single physical property of a rock is completely satisfactory as a predictor of penetration rate, coefficient of rock strength showed a better correlation with penetration rate than did other physical properties. Results also indicate that over the range of energies investigated, energy per unit volume in a given rock is independent of blow energy. A drillability index for the percussive system is proposed that utilizes the coefficient of rock strength test to determine energy per unit volume for a given rock which, along with the work rate of a given drill and the bit diameter, is used to predict the penetration rate as shown in the following equation: [R = 4P pD2 E, where R = penetration rate, in/min, P = work rate, in lb/min, D = bit diameter, in, and Ev = energy required to produce a given volume of rock, in lb/in3.] Laboratory tests indicate this method's potential as a simple and reasonably accurate method of predicting penetration rates with any percussive drill and bit combination.

Jan 1, 1969

By David R. Hanson

Experimental work performed by the Bureau of Mines in a laboratory environment has shown that the formation of failure zones within certain rock types is accompanied by the emission of significant amounts of radiofrequency (RF) electromagnetic (EM) energy. This radiation was detected using nonresonant, "electrically short," broad-band antennas. Rock types for which emission was observed include granite, quartzite, and taconite; sandstone and marble did not emit measurable radiation. Amplitude spectra of the radiation showed the energy to be concentrated between 10 and 40 kilohertz. These data indicate that emission is directional, but this has not yet been proven. In addition, amplitude of RF emission increases with increasing crack size. Since emission was observed only for brittle quartz-bearing rocks, it appears the formation of piezoelectric fields is a necessary condition for RF radiation. Plausible mechanisms for emission include rapid decay of piezoelectric fields accompanying the sudden stress release at failure and/or the acceleration of an "exoelectron plasma" through the intense local piezoelectric fields. Since emission appears to increase with the scale of failure, and since antennas do not need to be coupled directly to rock surfaces as with conventional geophones, the possibility of developing a portable system to monitor seismically active areas exists.

Jan 1, 1981

"Initiated as a part of the Bureau of Mines program for development of strategic minerals for national defense, various mines in the Poughkeepsie Gulch and Mineral Point mining districts were examined by C. R. Wilfley, W. R. Hamilton, .and N. E. Wvvlwy, Jr., Bureau Of 'Mines engineers, in July and August 1943, July 1944, and September 1945. In a subsequent report a proposal was made to evaluate this isolated area 'of some 15 square miles located in Ouray and San Juan Counties, Colo.Reconnaissance work in the area was begun in June 1946. Mapping and sampling were begun in July and was completed in Pougkeepsie Gulch and extended westward to include the Hendrick Gulch area of the east side of Ironton Park. Project work was recessed for the winter on October 15, 1946 after approximately 6 square miles of the Poughkeepsie Gulch,district been mapped and 801 samples had been taken.In this report the physical features, climate, and ore deposits districts are described, and a brief history of mining and production lead, zinc; and silver is given.The individual mines and prospects in, the area are described in detail.A list of patented claims and ownerships is given in appendix I, and analyses of samples are tabulated in appendix II.The San Juan preliminary project was directed by Paul T. Allsman, chief, Salt Lake City Branch, Mining Division and was supervised by William M. Traver, Jr., supervising engineer, Colorado Field. Office.Chemical analyses were made by the Salt Lake City laboratory under the direction of H.E. Peterson, chemist, and S. R. Zimmerley, chief, Salt Lake City Branch, Metallurgical Division.Harold A. Waddington, president, Great Divide Mining & Milling Corp., and Ernest Miller, owner, Como Consolidated Mines, were particularly cooperative in making available maps and data concerning their properties."

Sep 1, 1949

By A. L. Johnson

In this Bureau of Mines report, time-resolved infrared emission spectra and corresponding pressure and temperature histories are reported for large-scale propagations of CH4-air, CH4-air-N2, and CH4-air-CF3Br ignitions in a 12-ft-diam sphere. Absolute spectral radiances were obtained throughout combustion over the 1.6- to 4.8-gym range, and the radiance growth patterns for the H20 (2.5-µm) bands are presented as a function of methane stoichiometry and diluent concentration. Flame temperatures were determined from the C02-band emissions, which approximated unit emissivity shortly after ignition. Burning velocities are also given for some of the test-mixture compositions. Measured flame temperatures were in excellent to fair agreement with theoretical adiabatic values for the CH.-air and CH4-air-N2 mixtures; the best agreement was for the stoichiometric CH4-air mixture. The CH4-air-CF3Br mixtures with =2 pct CF3Br gave poor agreement with theory. The measured temperatures were significantly lower during the early stage of combustion; furthermore, the later stage of combustion was uninhibited and yielded unexpectedly high pressures. Supplemental data from a 2-ft-diam sphere at various initial pressures confirmed that the CF3Br inhibition effectiveness decreases with increased pressure. The possible effects of buoyancy, turbulence, and changing kinetics are discussed.

Jan 1, 1977

By Robert E. Hershey

1. The investigation shows that the Sewanee coal bed is the most important bed in Grundy County arid is the only bed that has had any sustained production. There is no production, at the present time, from any of the other coal beds in the county. The Richland (Lower Sewanee or Coke Oven) coal bed has been prospected but has never been developed extensively. The Angel coal bed has been worked to a very small extent near Beersheba Springs, Tenn., for local consumption. The Battle Creek coal bed has been worked sporadically near Monteagle, Tenn. 2. Known measured and indicated reserves in the Sewaneee coal bed, based on a minimum thickness of 14 inches and on 1,800 short tons per acre-foot of coal in place, are estimated to be 15 millon short tons as of January 1, 1953. Of this total, 10 million tons represents coal 28 inches and more thick. Areas in the bed were omitted from the estimate where available data relative to the bed characteristics are too meager for making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1955

By Peter J. Clarke

Afghanistan's mineral industry continued to be dominated by the production and export of natural gas, although several mining and related industrial projects, all under the supervision of Soviet technicians, were in the planning stage in 1982. Afghanistan produced minor quantities of barite, cement, coal, fertilizer materials, iron, and lapis lazuli, all for domestic consumption.2 Large-scale projects being investigated were a copper mine and concentrating plant at Ainak, extensive mining of the Hajigak iron ore deposit near Kabul, construction of an oil refinery at Angot, increasing production and processing of natural gas, and implementing an intensive geologic prospecting and exploration program for areas of mineral potential. Afghanistan's gross domestic product (GDP) was estimated at $2.76 billion3 and has remained stagnant for the past several years. Total exports in 1982 were estimated at $700 million, only a marginal increase from the 1981 figure of $694 million. Exports of natural gas to the U.S.S.R. earned $385 million in 1982, representing just over one-half of Afghanistan's total exports. Natural gas revenues were down approximately 11% from the 1981 level, owing primarily to increased antigovernment activity in the northern part of the country.4 About 90% of the country's natural gas production was exported to the U.S.S.R.5 About 38% of Afghanistan's development budget had been earmarked for mining and industrial projects in 1982.6

Jan 1, 1984

By A. J. Barry

[This is the third report related to fundamental retail roof-bolting research in underground mines (1, 2)3/ and describes an investigation of the torque-load relationship for 3/ -inch, expansion-type mine roof bolts. In a previous investigation the relationship between torque and bolt load was established for 1-inch slotted-type bolts (1). The two types of bolts differ in diameter and method of tightening and consequently may exhibit different torque-load behavior. The 1-inch bolt is tightened by turning the nut, the 3/4-inch bolt by rotating the beaded bolt itself. Experience indicates that roof bolts should be tightened to moors satisfactory anchorage sand to minimise nag of tie roof over the mine opening. The generally accepted means for determining the bolt load is to see a torque wrench to measure he torque applied in tightening the bolt and, from a predetermined relationship between torque and molt load, to, determine the corresponding bolt load. Because frictional effects may vary between one type of shell assembly or bolt and others, 7 types of expansion shell units and 3 types of 3/4-inch-diameter, mild steel bolts were tested.]

Jan 1, 1954

By Iam Pou Ng

Combustion aerosols consist mainly of elemental and organic carbon (EC and OC). Since EC strongly absorbs light and thus affects atmospheric visibility and radiation balance, there is great interest in its measurement. To this end, the National Institute for Occupational Safety and Health (NIOSH) published a standard method to determine the mass of EC and OC on filter samples. Another common method of measuring carbon in aerosols is the aethalometer, which uses light extinction to measure "black carbon" or BC, which is considered to approximate EC. A third method sometimes used for estimating carbon in submicron combustion aerosols, is to measure particle size distributions using a scanning mobility particle sizer (SMPS) and calculate mass using the assumptions that the particles are spherical, carbonaceous and of known density. With an eye toward evaluating the use of these methods for measuring carbon in freshly emitted diesel aerosols, the objective of this paper is to compare the results among these methods and to investigate the role of OC when measuring the mass concentration of elemental carbon (or black carbon) in aerosols emitted by a medium-duty Diesel engine. Results indicate that the aethalometer response correlates well with the data from filter samples (R2 = 0.99), with a very slight positive interference at high levels of OC.

Jan 1, 2008

By K. R. Farley

A simplified method for the atomic absorption determination of antimony is described. Samples are dissolved in hydrobromic acid and diluted to volume with water. Solutions can be ready for analysis in about 10 minutes and are stable for at least 24 hours. The spectral line at 231 nanometers is used, and there is no effect on absorption resulting .from the presence of any concentration of HBr. Absorbance is linear with antimony concentrations up to 120 micrograms per milliliter. Sensitivity is 1.48 micrograms per milliliter per 0.0044 absorbance. Relative errors on National Bureau of Standards Standard Reference Materials were 3 percent or less, and relative standard deviations on 12 determinations of each of three flue dust samples were 4 percent or less (95-percent confidence limit).

Jan 1, 1980

By Michael D. Fenton

Social and political movements that had been gathering momentum over several years continued in 1993 to dramatically affect and inspire uncertainty on the global mineral industry. Privatization of government-controlled mineral industries continued throughout the world, especially in Africa, Asia, Central Eurasia, Eastern Europe, Latin America, and Western Europe. The reasons for privatization varied among regions and countries, but the trend was universal and was not expected to end soon. Regional trade blocks were being developed and expanded. The European Union (EU), the North American Free Trade Area (NAFTA), the Association of Southeast Asian Nations (ASEAN) , the Asia Pacific Economic Cooperation (APEC) , and the Latin American Southern Cone Common Market (MERCOSUR) were expected to contribute to reduced internal tariffs and increased minerals trade. Minerals consumption within the politically unstable former Soviet Union (FSU) decreased significantly without a simultaneous cutback in production, while its exports flooded the world's mineral markets. These exports into Western Europe and Japan, still in economic recession, depressed minerals and metals prices worldwide, especially for aluminum, magnesium, nickel, and potash. Increasingly restrictive environmental laws and land-access limitations in Australia, Canada, Western Europe, and the United States tended to discourage mineral resource development. However, the number of undeveloped countries in Latin America and Asia that encouraged exploration and development by revising mining and tax laws and regulations increased, thereby increasing investment opportunities for foreigners.

Jan 1, 1995

By R. Unger, L. Mallett

The use of virtual reality (VR) technologies to train miners is an evolving area in research and development. In July 2006, representatives of 14 international organizations met to discuss current VR-related efforts and explore ways to employ VR in the future. This paper gives an overview of the various approaches presented at the meeting and discusses directions for future implementation. An example of a training package that teaches mine map-reading skills is presented. The meeting was the first step to building collaborations for furthering VR applications for mining. Planning has begun for a 2008 meeting open to broader participation. Disclaimer: The findings and conclusions in this report are those of the authors and do not necessarily represent the views of the National Institute for Occupational Safety and Health.