Search Documents

By Donald P. Tuchman, Robert P. Vinson, Steven J. Page

Researchers at the National Institute for Occupational Safety and Health (NIOSH) have long used stationary tapered element oscillating microbalances (TEOMs®) in laboratory settings. They have served to assess the mass concentration of laboratory-generated particulates in experimental , dust chambers and they provide a reference method for comparison with other particulate- measuring instruments. Current NIOSH research is focused on further adapting TEOM technology as a wearable personal dust monitor (PDM) for coal mining occupations. This investigation's goal is to help identify, quantify, and provide means for resolving certain TEOM- related error. The present research investigated bias caused by thermal effects on filter assemblies. New filters used in the PDM for 8 h tests show an average positive bias of 25.5 pg, while similar tests of equivalent filters used in two 1400A model TEOMs show an average positive bias of 34.3 µg. The derived bias values allow correction of previously collected biased data. Also, pre- heating the filters for 24 h at 46° C shows significant bias reduction, with PDM pre-heated filters subsequently averaging -3.3 µg and 1400A TEOM filters averaging 5.9 µg. On a single-point comparison to gravimetric sampling, a 25.5 µg bias is only significant at low mass loadings. At 2.5 mg, this bias represents a negligible 1 % of the mass measurement. If ordinary linear regression is used, the bias is still insignificant. However, if the more valid weighted linear regression is used, it gives more weight to the smaller dependent variable values, which are more impacted by the bias. Consequently, what is 1% bias on a single high-mass value can translate into a larger bias percentage at high-mass values when performing a weighted regression on data that include a large number of low-mass values.

Reduce methane levels around the shearer machine during longwall mining by directing more of the available airflow along the face and over the shearer body. Approach To address the entire mining cycle, two techniques were combined to dilute and clear the methane liberated from the face by the shearer during cutting. The first is the modified shearer clearer system, which is used during the entire face pass. This is combined with the walkway curtain which is used only during the headgate cutout. How It Works Methane ignitions are one of the most potentially serious hazards facing longwall mine operators. The high rate of coal extraction on longwall sections can liberate a significant quantity of methane during a pass. The modified shearer clearer is used to dilute methane concentrations along the entire face for both cut directions. The shearer clearer system, originally designed as a dust control technique, uses a series of water sprays located on the shearer body to direct more airflow along the face and over the shearer. (See Technology News issues, #112, #118, and #221). The only change from the original shearer clearer design is the addition of three sprays to the return-side splitter-arm/ shearer interface. The additional sprays help to ventilate the area behind the shearer body.

Jan 1, 1985

By Rollien R. Wells

THERE are two recognized methods of recording the state of the metallurgical art. One involves delineation of individual advances reported in the literature. This approach is used effectively in the excellent annual reviews published by some of the leading technical journals and in the technology sections of the individual commodity chapters in this volume. In an effort to more clearly indicate the current trend of metallurgical research and development, the authors of this chapter chose the method of discussing generally selected items of interest brought to their attention during 1959. Since technology cannot be confined by dates on a calendar, most of the items mentioned have been in the process of development for several years. No attempt was made to identify the sources of information used here. Material was drawn from many sources : Nonconfidential correspondence and conversations with authorities of the metallurgical fraternity, papers delivered at technical meetings, and articles noted in the technical press, including particularly Engineering and Mining Journal, Metal Progress, Journal of Metals, Mining Engineering, Industrial and Engineering Chemistry, Chemical Engineering, Chemical and Engineering News, Chemical Week, Materials in Design Engineering, Review of Metal Literature, the Canadian Mining and Metallurgical Bulletin, the Mining Journal (British), and the Journal of the Institute of Metals (British).

Jan 1, 1960

By V. A. Marple, K. L. Rubow

"In our laboratory several impactors have been developed in the past which have penetration characteristics that approximate that of the ACGIH or the British MRC respirable curves. In these impactors the large nonrespirable particles are collected on an impaction plate of a multiple round nozzle stage where the nozzles are of different diameters. The principle for designing a respirable cut impactor is quite simple in that the respirable curve is divided into two or more segments and the nozzles are designed with the correct diameters and number of nozzles to have collection characteristics with 50% cutpoints at the center of each segment. The particles not collected on the impaction plates are then collected upon a filter. These particles represent the respirable fraction of the aerosol. Therefore the respirable curve is approximated in a stepwise fashion with the approximation becoming better as the respirable curve is divided up into increasing numbers of segments. It has generally been felt that three segments is satisfactory for most cases.A new version of the respirable impactor has recently been developed in our laboratory. This impactor approximates the ACGIH respirable curve in three steps at a flow rate of 30 liters per minute. However, unlike previous models where all of the particles larger than the three cut points designated by the three steps are collected upon one impaction plate, a separate impaction plate is now used for each of the three cut sizes. To approximate the respirable curve in three steps, the cut sizes must be 2.2, 3.5 and 5.8 microns diameter. Therefore, on each of these stages the particles collected will be the mass of particles that are larger than these three cut sizes. By determining the mass of particles collected on each of these three stages plus that on the after filter using Gravimetric techniques, some information can be obtained on the size distribution of the aerosol being sampled. Furthermore, the impaction plates of the three stages are rotated and the nozzles are placed in such a position such that a uniform deposit is obtained on each of the impaction plates. Therefore, the deposits collected are suitable for X-ray fluorescence analysis or other types of analysis where a uniform deposit is required."

Jan 1, 1988

By Oliver Bowles

Slate possesses many admirable qualities, not only as a roofing material, but for blackboards, electrical switch boards, and for various structural uses such as stair trends, floor tile, baseboards, and sanitary enclosures. The American slate industry was established manor years ago, and has made remarkable progress, particularly during the past five years. One of the chief drawbacks to more rapid expansion is the high percentage of waste which reaches 75 to 94 per cent of gross production. Much of this waste is duo to rock imperfections over which man has no control, but a careful study of tae industry by the Bureau of Mines over a period of years indicates that an undesirably large percentage of the marketable slate is wasted in the processes of quarrying and manufacture. The initial step in quarrying slate is to separate from the solid ledge masses of a size that ray be conveniently removed from the quarry. This first step entails a greater waste of material than any subsequent process, and, therefore, invites the most earnest effort toward waste reduction. Attention has consequently been directed toward possible improvements in methods of making primary cuts in the quarry floor. A study of European practice with the wire saw, together with theoretical consideration of its advantages, convinced the writer that it possessed sufficient merit to justify its use as a primary slate cutter in American quarries. No practical conclusion in this matter could be reached except by experiment. Therefore, the desirability of obtaining equipment and trying it out under actual conditions of operation was urged upon operators. While no doubt the equipment could be readily manufactured in America, it had already been developed to the point of practical use in Europe; therefore the writer urged the desirability of purchasing one completely equipped wire saw in Europe, and determining through tests whether it gave sufficient promise of success to warrant its manufacture in America.

Jan 1, 1927

By Victor E. Kral

"INTRODUCTION The Segerstorm-Heizer property was examined by engineers 3/ of the Bureau of Mines in May and June 1942 and Mach 1943. As a result of these examination, the Nevada State Department of Highways,constructed 9.3 miles of graveled road under the mine access-road program. A magnetometer survey was made by the Geophysical Division 4/ in October 1943, and as a result the Mining Branch set up and conducted a core-drilling,project. Work on the deposit started May 24, 1944, and was suspended on July 31, 1944, but was resumed on December 4, 1944 and continued until completion on March 27, 1945.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as it, primary objective the more effective resource to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploration work, and prepares the final report. The Metallurgical Branch, R. G. Kinickerbocker, chief analyses samples and performs beneficiation tests."

Mar 1, 1947

By C. B. Manula, R. L. Sanford, R. A. Rivell

This report describes the development and application of a rail haulage simulator that is readily adaptable for the analysis of a wide variety of operating problems. Various gaming, options have been integrated into the model structure which permit trial and error solutions from a computer terminal prior to capital committment in the actual operation. The high level of information retrieval available allows engineers and managers to develop production data which fit individual needs. In this report, emphasis was placed on the problem of organizing and performing the sequence of operations that are necessary to accomplish a complete mine materials handling simulation. Here, the Rail Haulage Sub-assembly was linked to the Production Sub-system to mine and move coal from seven operating sections to the intermediate and main-line track. The analysis was devoted to the problems associated with how the operating system performs and what alternatives were available to minimize idle times and hence increase productivity. In order to have some objective means of evaluating which of the alter- native methods for production was most appropriate, the choice was to replace the intermediate track with belt conveyors. Since the attempt here was to demonstrate model flexibility and not to establish the goals or trade-offs between computing objectives with which systems judgement must contend, no further alternatives were tried. This is left to management with the data and a problem to solve. Rail haulage simulation is not new, and several, operationally tested models are being used in practice (Bucklen, et. al., 1968).

Jan 1, 1974

By H. J. Fissan, G. Ananth, K. Rubow, V. Marple

"INTRODUCTION Over the past several years a new type of cascade impactor that utilizes small nozzle diameters (micro-orifice nozzles) has been under development (Kuhlmey et al., 1981; Marple et al., 1981). The small nozzle dimensions allow for particles to be collected as small as 0.024 µm aerodynamic diameter on the last stage of the impactor. To obtain a reasonable flow rate of 30 I min - i through the impactor, a large number of nozzles (up to 2000) are required per stage.Furthermore, by locating the nozzles of multi-nozzle stages in a prescribed manner (described in detail by Marple et al., 1981) and rotating the impaction plates relative to the nozzle plates, uniform deposits can be achieved on the impaction plates. As described by Marple et al. (1981), the advantages of a uniform deposit impactor over the conventional impactor that collects particles only beneath stationary nozzles are: (1) maximum use of the impaction substrate surface, reducing both particle bounce (if substrates are greased) and tare weights of the substrates (if particle mass is measured gravimetrically); (2) deposited particles can be analyzed for elemental composition by X-ray fluorescence (Dzubay and Rieke!, 1978); and (3) the pressure in the impactor can be kept relatively high compared to low pressure impactors that depend on a large slip correction to achieve small particle collection (some types of particles may evaporate at low pressures). The work described in this paper investigates two additional advantages of a uniform deposit impactor. These are: (1) the possibility of collecting two separate deposits at one time on one stage for two types of analysis techniques, and (2) the possibility of utilizing piezoelectric quartz crystal impaction plates more effectively by eliminating the deposit location sensitivity nature of the crystals (Schulze-Frohlich, 1981 ).MICRO-ORIFICE UNIFORM DEPOSIT IMPACTOR (MOUDI)A photograph of an eight-stage MOUDI is shown in Fig. 1. Each stage body of the impactor supports the impaction plate for the stage above and the nozzle plate for the stage below as shown in Fig. 2. By rotating alternate stage bodies, while holding the other stage bodies stationary, the impaction plates (or nozzle plates) will be rotated relative to the nozzle plates (or impaction plates).Rotation of the alternate stage bodies is achieved by gears on these bodies that mesh with gears on an electrically driven drive shaft of a rotating mechanism (Fig. 1 ). The alternate stage bodies are restrained from rotation by pins that rest on the drive shaft."

Mar 1, 1989

By Kenneth B. Higbie

Expenditures to advance scientific technology in general reached an all time high in 1965 with some $22.2 billion estimated to have been allocated by government and industry. Federal Government expenditures were estimated at $15.4 billion, with almost 90 percent of the funds devoted to programs involving defense, atomic energy, and outer space efforts. With this massive effort in the United States and a very impressive effort elsewhere in the world, there is little wonder that many new metallurgical developments were announced in the technical press during the year. No effort has been made to cover all aspects of the industry, but a few of the developments are described in this chapter.

Jan 1, 1966

By Peter F. Strong, Robert L. Lagace, Alfred G. Emslie

This paper is concerned with the theoretical study of UHF radio communication in coal mines, with particular reference to the rate of loss of signal strength along a tunnel, and from one tunnel to another around a comer. Of prime interest are the nature of the propagation mechanism and the prediction of the radio frequency that propagates with the smallest loss. Our theoretical results are compared with measurements made by Collins Radio Co. This work was conducted as part of the Pittsburgh Mining and Safety Research Center's investigation of new ways to reach and extend two-way communications to the key individuals that are highly mobile within the sections and haulage ways of coal mines.

Jan 1, 1973

By Donald R. Irving

THIS CHAPTER is new to the Minerals Yearbook and will appear regularly hereafter. Its purpose is to present statistics that reflect technologic trends in the minerals and metals industries (except fuels). Much useful information has been collected annually through the Bureau of Mines mineral commodity and employment and injuries canvasses. However, these data must be supplemented by further data to permit evaluation of the type, direction, and rate of technologic change, which are vitally important in long-term mineral planning. In addition to, and fully as important as, expanding the available data is the need to ascertain that the various items collected are obtained from identical reporting units, to enable direct comparisons to be made.

Jan 1, 1960

By B. P. Martinez

This report presents the results of a research and development program in recovering waste-rolling oils conducted by the Bethlehem Steel Co., before 1954 at its Sparrows Point plant, Sparrow Point, Md., with the cooperation of the Bureau of Mines, U. S. Department of the Interior, College Park, Md. The objective of the program was twofold: First, to recover oil for reuse in the plant; and second, to stop pollution, by oil, of the stream and harbor areas in the immediate vicinity of the plant. The sequence of the investigations was laboratory and pilot plant studies on sedimentation, simple aeration, and flotation for the separation of oil and water; and construction of a production unit using standard flotation equipment. This work was only preliminary for the Bethlehem Steel Co. and it has continued research on this problem. Recent progress indicates that new, improved processes will soon replace the flotation units described in this report. The first efforts to separate oil and water by simple sedimentation were unsuccessful. To establish the cause of this failure, microscope examinations and measurements were made on cold-reduction rolling mill cooling-water effluents containing oil in suspension. It was discovered that an average oil globule, held in suspension, was only 0.001 inch in diameter and would not coagulate with other globules for normal sedimentation at room temperature. The next step in the sequence of studies was to coagulate the oil suspension by simple aeration with air under slight pressure. The aeration methods studied were effective in removing up to 68 percent of the total oil but were approaching flotation in principle. The final investigation of the series was flotation of the oil in conventional laboratory-size flotation cells. The small-bubble method, without reagents, floated up to 89 percent of the total oil held in suspension and was the process selected for pilot-plant development.

Jan 1, 1959

By Byron. O. Pickard

"An Arizona mining company recently demonstrated a new use for the geophone by successfully locating leaks in compressed-air lines which were buried under from 1-1/2 to 2-1/2 feet of fine rock fill. The following information is abstracted from data sent to the Bureau of Mines by the superintendent of the mine.The company has two parallel main compressed-air lines, about one and one-half miles long, buried under an average of two feet of fine rock fill. One of the lines is a four-inch high-pressure (1000 pounds) main, and the other line a ten-inch low pressure (90 pounds) main. The two mains are separated by a 10 to 3C foot interval, and run from the compressor plant to the No. 2 shaft, where they are taken underground. A pump line is also buried in the immediate vicinity.Several leaks, not audible enough to be located, were developed in the Alms. Various =Abode were suggested that did not seem practicable to the management. Finally, the company obtained a Bureau of Mines' geophone and experimented with it. The first test& were conducted while the pumps were running, and while there was noise on the concrete pavement, all of Which caused so much vibration in the geophone that it was impossible to detect the leaks.The second attempt was made at the close of the day shift when the compressors were not operating and when the pumps could be shut down. The valves in the far end of the surface lines were closed, and the lines were pumped to full pressure (90 and 1,000 pounds respectively).Geophone readings were then taken at 7 or 8 foot intervals directly see the lines. Several leaks some very large in the high-pressure line were audible with the geophone at distances varying from 15 to 30 feet. A con-le leak in the low-pressure line was found at a distance of 10 feet. detecting the leaks, no difficulty was found in locating them exactly. ""At this time"", laid the superintendent of the mine, are unable to large a leak must be in order to be located under two feet of loose geophone. The fill we worked over was quite loose and dry and unfavorable for the work in question. However, we have no that the instrument is a valuable adjunct to our business""."

Aug 1, 1922

By Dana Reinke, Launa Mallett, Michael J. Brnich

Some segments of the mining industry, especially underground coal, have seen a large influx of inexperienced miners in recent years. It is anticipated that this trend will reach other mining segments over the next 10 years. This paper discusses the training needs of the younger generation of inexperienced workers who have just entered or are soon to enter the mines. Currently, many trainers are of the so-called Baby Boom generation. Can these different age groups learn to communicate across the generation gap? Even trainers who have been highly effective in the past should reassess their training styles and their classroom materials to determine if they are prepared to meet the needs of these new trainees.

Jan 1, 2002

By Christopher C. Jobes, Alan G. Mayton, Farid Amirouche

Based on prior mine vehicle studies of operators’ exposure to whole-body vibration, researchers from the National Institute for Occupational Safety and Health (NIOSH) evaluated four seat designs on mine haulage vehicles, with regard to roadway-induced jarring/jolting and operator comfort. Investigators collected objective and subjective data from vehicle operators on two existing and two NIOSH seat designs. This study included time and frequency response data using accelerometers and a data recorder, operator perceptions of jarring/jolting and discomfort levels using a linear visual analogue scale, and data from a questionnaire developed for this study. Results from the analysis of subjective data show that operators generally favoured the NIOSH-designed seats over the existing seats. The results of analyses from the absorbed power method and the threshold limit method, based on ISO 2631-1 (ISO, 1985), support the premise that NIOSH seat designs are superior to the existing vehicle seat designs on both models of mine shuttle cars used in the study. The NIOSH seat designs, featuring viscoelastic foam padding, were more effective in reducing vibration energy for operators exposed to vehicle jarring/jolting. In this paper, the performances of the NIOSH and existing seat designs are compared relative to the operator’s exposure to vehicle vibration (mainly jarring/jolting).

By Walter W. Fisher

Cement copper was flash roasted in a vertical tube furnace to convert the copper to acid-soluble oxides as part of a postulated process for refining cement copper by oxidation roasting, acid leaching, and electrowinning. The results of the study showed that the oxidation was a linear function of oxygen concentration between 0 and 20 percent, but above 20 percent oxygen there was no further increase in oxidation. Therefore, air was the optimum oxidizing atmosphere in this flash roasting system. The oxidation followed a parabolic rate law as the roasting temperature was increased from 400° to 800° C. Extrapolation of the data, based on the parabolic law, indicated that at 400°, 500°,600°,700°, and 800° C, the roasting times required for complete conversion to soluble oxides were 75, 37, 21, 7.7, and 4.6 seconds, respectively. Cyclic-roasting test results did not substantiate the predictions obtained through data extrapolation.

Jan 1, 1973

By C. E. Schmidt

Condensate waters from the Bureau of Mines Synthane process for coal gasification have been investigated by mass spectrometric methods to determine the organic contaminants. Waters from the gasification of six coals were extracted with methylene chloride, yielding 0.6 to 2.4 weight-percent extractable material. Using high-resolution mass spectrometry (HRMS), combined gas chromatography-mass spectrometry (GC-MS), and low-voltage mass spectrometry, 60 to 80 percent of the extract was found to be phenolic. About 20 organic contaminants have been identified and are present in the condensate waters from each coal gasified. The relative distribution of contaminants in the condensate water was nearly the same for the six coals gasified under various conditions; phenolic compounds were the most abundant in all cases.

Jan 1, 1974

By Linda L. Chasko, Larry D. Stowinsky, Ronald S. Conti

Mine operators often rely on mine rescue teams to save lives during an underground emergency such as an underground fire, explosion or roof fall. It is extremely important that team members are provided with adequate exploration equipment and that training simulations are conducted in a realistic manner. A series of mine rescue training exercises was developed, conducted and evaluated by the National Institute for Occupational Safety and Health (NIOSH) in cooperation with the Pennsylvania Department of Environmental Protection, Bureau of Deep Mine Safety. The exercises were conducted at NIOSH’s Lake Lynn Laboratory during 1995 to 1998 and resulted in improved technology and training for mine rescue teams. For example, existing technologies were identified to help rescue teams during exploration. These included chemical light sticks to identify team members and mark crosscuts and mine materials, strobe lights for mapping out escape ways, and a helmet mounted thermal imaging system to see through smoke. A hands-free communication system showed potential for enhanced communications between team members and the fresh air base. A new high-visibility team lifeline that allows for flexibility of movement between team members was developed. A positive-pressure inflatable escape device (IED) was used to isolate the “hazardous” environment from fresh air and allow rescue team members to traverse through. An inflatable feed-tube partition that can rapidly block large openings such as underground passageways and simultaneously provide a feed-tube for high-expansion foam generators was also deployed for several simulations. During the simulations, mine rescue team members donned self-contained breathing apparatuses (SCBA) and traversed more than 305-m of mine passageways filled with nontoxic smoke. Visibility ranged from 0.3 to 0.9-m. In one area of the mine, a kerosene heater was used to simulate a fire and reduce the oxygen concentration. In another area, a 1.5 pct methane zone was established. The team members searched for "victims,” mapped the passageways, built temporary stoppings and ventilated the smoke-filled entries. The teams indicated that the simulations were challenging and very informative.

By Raja V. Rarnani, Robert L. Frantz

"Scientific, engineering, and biomedical research teams synergystically developed major topical research areas in the Respirable Dust Center. Descriptions of their interactions and resulting accomplishments demonstrate how cooperative research within and among these study groups benefits the overall respirable dust research and practical application needs of the mineral industries.The development of a state-of-the-art small animal inhalation exposure facility suitable for studies of fresh and aged coal mine dust, a major goal of this research group, will contribute toward the GTCRD goal of advancing the understanding of causative mechanisms for the occupation-related lung impairments and the airway diseases of mine and mill workers. Such understanding includes improved definition of the role of various aspects of the lung environment (e.g., surfactant and the mucociliary system) in the disposition and toxicity of respirable dust, comprehensive characterization of the role of the pulmonary alveolar macrophage (PAM) and its secretory products on the development of dust-related lung disorders, and an expanded search for methods to reduce the toxicity of respirable dust both before and after it enters the lung. The National Academy of Sciences has recommended, in Measurement and Control of Respirable Dust in Mines, that respirable dust research should include study of the behavioral and constitutional factors affecting individual susceptibility to workers' pneumoconiosis occupational disease and the development of methods for detecting the potential onset of pneumoconiosis earlier and more conclusively than can be done using X-ray methods. These recommendations have guided the research group in its goals of establishing and disseminating a scientific protocol for standardizing the inhalation testing for all research objectives within the Generic Center which involve small animal exposures and implementing the infrastructure necessary to make lung tissues obtained during inhalation studies available to all researchers within the Generic Center."

Jan 1, 1995

By ROBERT R. ROUGH, FRANK L. BACON, John Dasher

(being shipped as bailast in ocean freighters). Within the last 10 years it has become more economical to use local sands, and there has been a general shift from the Belgian sand. Deposits of purer sand were treated and used for 'some time: but the suprly became limited, and means were sought to beneficiate the more bountiful subpay-f impure beach sands. These sands are composed of, 50 percent feldspar and 50 percent quartz, with small amounts of iron- bearing minerals, The most objectionable impurities in these West coast sands are the oxides of iron and aluminum. The Del Monte (Calif.) beach sand contains about 0.13 percent FeqQg and about 11.0 percent Aig03 (the latter being furnished by the large amount of feldspar present.) For the manufacture of feldspar present.) For the manufacture of flint-glass containers the maximuni quantities of these two impurities permitted in the sand are 0.05 percent F20 and 6 to 8 percent A1203.. The Fe0g occurs in the sand as follows: Traces of iron-bearing minerais resistant to weathering, ferruginous clay stains on the sand grains, and iron minerais not visible and possibly in solid solution or as colloidal incisions in the grains of feidspar or quartz. A good part of the iron in the sand is present in the traces of iron-bearing minerals, biotite, ilmenite, garnet, monazite; and hornblende. Biotite is present in larger quantities than the others. Samples of quartz, were freed of iron-bearing minerais by the use of heavy liquid (sp.gr. 2.70), leached with boiling HCI and SnCl2. Under a microscope a few apparently clean quartz grains were selected, and Fe203 was determined spectrographically to be 0.03 percent. The technique is similar to that described by Gabriel and Slavin. 4/

Dec 1, 1943