Search Documents

By G. R. Friggens

A nuclear method for continuously monitoring the coalbed and ash levels and void formation in commercial-scale, fixed-bed, pressurized gas producers is proposed. Measurement of gamma ray transmission through the coalbed is the basis of the method. The coalbed level is monitored by detecting the trans-mission of gamma rays from a 1 to 2 Ci Co-60 source positioned on the outside wall of the vessel. Coal bridging or, alternatively, ash level is monitored by a 10 Ci Co-60 source at the center of the coalbed. Source activities and geometries are calculated for a 12-foot-ID producer designed to operate at 350 psi. Source capsule and detector specifications and operational safety are also discussed.

Jan 1, 1973

By E. J. Kloos

The Bureau of Mines evaluated all previously approved gas masks to determine their ability to provide respiratory protection against each of the following six selected amines: ethylenediamine, diethylamine, n-butylamine, ethylamine, methylamine, and hydrazine. Minimum requirements were a 24-minute service life at a flow rate of 64 liters per minute (32 liters per minute for hydrazine) and an amine concentration of 1.0 volume-percent (0.5 volume- percent for hydrazine). The three masks meeting these requirements were the LG4, Willson Products Division, The Electric Storage Battery Co.; the GMD-SS, Mine Safety Appliances Co.; and the 084-PHOV-R, Acme Protection Equipment Co.

Jan 1, 1966

By M. D. Schlesinger

Experimental data for coal hydrogenation are presented to show that when a vehicle oil produced from coal is present, coal is hydrogenated to the same high conversion whether molybdenum catalyst is impregnated on the coal or intimately mixed with the slurry. Differences in product distribution could be related to the severity of operating conditions. No minimum mixing time was established, but 2 hours was sufficient. Longer periods of mixing, to 14.75 hours, had no effect on the results. The hydrogenation conditions were in the pressure range of 8,500 to 10,000 p,s,i. at 400° to 500° C. Most of the experiments were made in duplicate. The results were obtained with molybdenum concentrations of 0.01, 0.1, and 1 percent. Al the mentioned pressure range and a time at temperature of 15 to 60 minutes, coal conversions higher than 98 percent were obtained.

Jan 1, 1962

By John C. Franklin

The Bureau of Mines conducted extensive laboratory and limited field tests to determine whether a polymeric material could effectively reduce the emanation rate of radon gas from uranium ore. In the laboratory 46 different single-coat materials and 14 two-coat applications were tested. The laboratory tests showed that up to 100 percent of the radon gas could be sealed into the rock. Materials tested in the laboratory were polyesters, furan resins, epoxies, latices, and totally inorganic coatings. From the laboratory work six different materials were selected for field testing. The first test was single-coat materials in five static chambers; the second test used two-coat applications in an open chamber. Both tests were conducted in the Dakota mine at Grants, N. Mex. During the second test, the amanation rate of radon gas was reduced up to 62 percent.

Jan 1, 1975

By R. P. Vinson, Abdurrahman Cetinbas, Joseph Cervik, M. G. Zabetakis

The periphery of longwall panels in the Pocahontas No. 3 coalbed is characterized by a zone of reduced permeability that inhibits the natural drainage of methane. A residual gas pressure of 105 psig was measured after 1 year in an isolated block of coal measuring 340 by 1,100 feet. The buildup of gas pressure within such large blocks causes methane problems during plowing operations. However, natural drainage holes drilled during development have been found to reduce the gas content of the coal in this coalbed by over 90 percent. The effect of water infusion on dust during plowing operations was investigated using existing methane drainage holes. These holes were cleaned of debris and a pipe was grouted into the hole for water infusion of the panel. Both total and respirable dust levels were reduced by 40 to 79 percent. Water infusion of the panel proved more effective than did the use of a plow-mounted spray sys tem.

Jan 1, 1974

By Paul W. Jeran, Michael A. Trevits, William P. Diamond

In this U.S. Bureau of Mines study, production trends have been analyzed for 82 gob gas ventholes on 7 longwall panels in the Lower Kittanning Coalbed, Pennsylvania. Cumulative production from individual holes was found to vary considerably, ranging from 0.03 x 106 to 10.1 x 106 m3. Peak production rates were generally about 0.03 x 106 to 0.06 x 106 m3/d, but rates over 0.10 x 1@ m3/d were observed. The variability of gas production from individual holes can be attributed to several factors, including completion practices and problems, the extent of fracture development in the strata above the extracted panel, water production, and location on the panel. Of particular significance is hole location. Holes on the ends of the panels, where overburden strata are in tension because of the support of the surrounding pillars, were generally the highest and longest producers. This observation led to the experimental placement of gob gas ventholes in the zone of tension along the margin of a panel, instead of in the traditional centerline location, which is in compression. Analysis of 7 months of gas production data indicates that the experimental near-margin holes produced 77 pct more gas than did centerline holes on the same panel.

Jan 1, 1994

Design a model health and safety program which, when implemented, can improve mine safety by reducing occupational injuries and accidents. Approach The Bureau of Mines developed a model program which identifies the elements essential to the effectiveness of health and safety programs designed for mining operations, and is readily adaptable to all types of sizes of mines. The model program primarily provides training on loss control and accident investigation and technical assistance with health and safety problems. In order to assess the effectiveness of the program, it was tested at both a coal and gold mining operation. Monthly statistics were generated to reflect the number of occupational injuries and accidents, and the severity of injuries (as measured by the number of work days lost during recovery). Observations were made of employees performing a large number of randomly selected jobs in order to estimate. the proportion of the workforce that was working in the presence of one or more of three types of safety deficiencies: Type A-individual job performance deficiencies which could be corrected by the employee alone I e.g., an employee is seen not wearing a seatbelt.

Jan 1, 1986

By E. C. Bennett

"INRTODUCTIONVarious methods of making leakage tests have been tried during a study of losses in the transmission of natural gas. This work has been carried on by the Bureau of Mines in cooperation with the Natural Gas Association of America. Results of torts show that the ""shut-in -pressure-drop"" method described by Rawlins is the most accurate and reliable; therefore its use is recommended. This paper describes a graphic method for computing the rote of leakage from the fall in pressure and change in temperature determined by the ""shut -in pressure-drop"" method of testing.METHOD OF MEASURING PRESSURE DROPThe gas is ""shut in"" line to be tested and is not allowed to escape except through existing leaks. The leakage causes the pressure in the line to fall. The charge in pressure is obtained with a dead weight gage. Approximate results may also be obtained from readings on a good spring test gage. Numerous tests show that the dead weight gage is more sensitive to small changes in pressure than spring gages.The temperature of the gas in the line is observed simultaneously with each pressure reading. Temperature changes affect the pressure exerted by a given quality of gas ""shut in a line, end since the rate of leakage from a closed system is directly proportional to the rate of pressure drop, fluctuations in temperature must be considered."

May 1, 1926

By W. H. Ode, F. H. Gibson, W. A. Selvig

The great expansion of production of aluminum for war purposes has aroused some concern regarding the available supply of carbon suitable for making carbon electrodes required in the electrolytic aluminum process. Approximately three-quarters of a pound of carbon electrode is consumed for each pound of aluminum produced. 5 Because of its small amount of impurities and its suitable physical characteristics, calcined petroleum coke is the standard material used by the aluminum industry for making electrodes As it may be necessary to use some substitute materials, the possibility of using coke made from coal has been considered. Besides this possible use, information concerning the source of low-ash coals is of general interest. Specifications of the aluminum industry for calcined petroleum coke suitable for the manufacture of electrodes are very stringent in regard to allowable impurities. In one such specification the maximum allowable ash is 1.0 percent; the maximum allowable content of iron (as Fe) is 0.06 percent and that of silicon (as Si) is 0.08 percent; the maximum for cal- cium (as Ca) and for sodium (as Na) is 0.12 percent for each, but the two combined may not exceed 0.12 percent; maximum allowable sulfur is 2.0 per- cent. The presence of barium, nickel, chromium, manganese, cobalt, or vanadium is objectionable, and only extremely small amounts are allowed. In regard to physical properties, the coke is required to be so thoroughly calcined that it has a real density of at least 2.02.

Nov 1, 1943

By L. B. Berger

In this investigation, the ampoule type of carbon-monoxide (CO) detector which is manufactured under license of U. S. Patent 1,644,014 (October 4, 1927) was tested for sensitivity and reliability. This detector was devised primarily for examining the air of manholes and sewers for possible dangerous contamination with CO before workman enter those places, but dine to the simplicity of the device it may have a more general usage for examination of atmospheres which are known or suspected to be contaminated with CO. Some of the suggested uses are the examination of the air in garages, tunnels, mines, around blast furnaces, gas plants, and in the home.

Jan 1, 1930

By Ted C. Briggs

The Bureau of Mines is evaluating the thermodynamic properties of helium and helium-containing mixtures. Twenty-two compressibility runs were made with helium at 0° C and pressures to 800 atmospheres using a Burnett-type apparatus. Data from the 22 runs were treated simultaneously and as separate runs while different functional forms and weighting factors were used. A fourth-degree-polynomial equation in the pressure gives a statistically satisfactory representation of the compressibility factor when the data are treated simultaneously and a weighting factor of Pr-3/4 is used. The second virial coefficient of helium at 0° C from this investigation is 11.997±0.015 cm3 mole-1. The stated uncertainty is the random error standard deviation. Compressibility factors determined by this investigation are precise to better than 0.01 percent and are believed to be accurate to better than 0.02 percent.

Jan 1, 1969

By John D. Sullivan, Edward P. Barrett

The experimental work on the utilization of tin-plate scrap at the North- west experiment station of the U. S. Pireau of Mines in cooperation with College of Mines, University of Washington, necessitated the selection of a simple method for the determination of tin in the iron produced. Some of the standard methods for the determination of tin which were tried are given below: 1. Dissolving in acids and precipitating the tin as sulphide, igniting and weighing as Sn02. 2. Dissolving in aciis, reducing with nickel, cooling in an atmosphere of carbon dioxide, end titrating with standari iodine solution. 3. Dissolving in acids, precipitating the tin as sulphide, dissolving this sulphide in H3 and H2S04, heating until fumes of 503 are evolved, reducing with nickel or sheet lead, cooling in an atmosphere of carbon dioxide, ani titrating with a standard iodine solution.

Mar 1, 1923

Compare the dust control efficiency and bit life of surface coal mine drills using standard water injection and water injection with water separation. Approach A research study was conducted to determine if a water separation technique affects wet suppression dust control. Dust control efficiency and bit life of surface coal mine drills were compared during tests using both standard water injection (wet drill bit cutting) and water injection with water separation (dry drill bit cutting). Background Surface coal mine blast hole drills typically generate a substantial amount of dust during the drilling cycle. One method used to control this dust is the injection of water into the bailing air. This is known as wet suppression.

Jan 1, 1988

By T. R. Waters, F. Li, R. L. Huston

This paper describes the development of a multi-body biomechanical model that can be used to assess the risk of low back disorders due to occupational exposure to jarring and jolting from operation of heavy mobile equipment (e.g., trucks, haulers, graders, tractors, etc.) The four-element dynamic spinal model is capable of providing estimates of the force and acceleration responses of the head/neck, upper, lower, and middle torso resulting from vibration input collected in field studies. The paper also presents a method for using the model output to assess an individual's risk of low back disorder due to a specific jarring and jolting exposure.

Develop a metal substitute which is more plentiful and less expensive than the metals currently being used in high performance, permanent magnets, while maintaining the quality of the magnet. The New Alloy The rare-earth metal used in most high performance magnets is samarium, an expensive metal of limited availability. Cobalt is also used in high performance magnets, but supplies of this metal also are limited because it is not domestically mined and must be imported. The Bureau of Mines embarked on research to find a less costly domestic: metal source for use in industrial magnets. The alloy found most promising consists of mischmetal, a relatively abundant, naturally occurring mixture of rare-earths, which can be used as a replacement for samarium. Additives of copper, magnesium and iron used in combination with mischmetal aid in replacing some of the cobalt needed for the magnets.

Jan 1, 1983

By A. B. Hooker

Investigations at the Pittsburgh Experiment Station have shown that the satisfactory operation of a flame safety lamp depends not only upon proper design and assembly of the lamp but upon the kind of fuel used, and that much of the trouble experienced with permissible flame safety lamps at mines is due to the common use of motor gasolines, none of which is suitable in the present types of permissible flame safety lamps. This report gives the results of a limited study to determine what satisfactory fuels are available, the specification limits of such fuels, and to suggest modifications of assembly and care of the lamps to improve performance with any satisfactory fuel.

Jan 1, 1938

By Richard J. Mainiero

The Bureau of Mines investigated coal-mine-type short-delay electric detonators marketed by three domestic manufacturers to determine the accuracy of delays and the probability of overlap between adjacent de- lay periods. The Winzer index was computed and compared with the probability of overlap. A close agreement between the Winzer criterion and overlap probability was demonstrated. A permissible blasting unit capable of delivering a maximum firing energy of 4.0 J and a digital oscilloscope were used to measure the delay time with an accuracy of 20.25 ms. Another oscilloscope and a pulse transformer were used to record firing current. Experimental data indicated negligible overlap probability in detonators of shorter delay periods: periods 1 to 4, which correspond to 25 to 250 ms. However, a significant probability of overlap was detected in some detonators of longer delay periods: periods 5 to 9, which cor- respond to 300 to 500 ms.

Jan 1, 1985

By E. Chin

Natural gas was Bangladesh's only significant exploited mineral. A few other minerals or mineral-based commodities were produced for local consumption. The most valuable were nitrogen fertilizer, salt, cement, and clay for brick.2 The most important mineral industry development of 1987 was the start of modest production of crude oil, the first discovered and produced in the country. PRODUCTION AND TIADE Production of natural gas from the nation's huge reserves continued to increase but was limited by the lack of residential and industrial demand. Gas reserves of 7 trillion to 16 trillion cubic feet were sufficient for far more production than the country could efficiently utilize for many years. The country's consumption-to-reserves ratio was one of the lowest of the developing nations. Mineral exports have been insignificant, comprising a small amount of nitrogen fertilizer. Nitrogenous fertilizer exports could become important when planned new capacity comes on-stream. Mineral imports were dominated by crude petroleum.

Jan 1, 1989

Develop a 22-ton capacity temporary mine roof support light enough to be easily lifted and transported manually from one place to another. Approach Several potential approaches were investigated in developing a new temporary support. An all-hydraulic, high-strength aluminum design was chosen as the best. The support was designed, fabricated, and tested in several mines. The first units, built for 6- to 8-foot seam heights, have a load- bearing capacity of 22 tons, and weigh only 55 pounds. How It Works The lightweight hydraulic support is designed for use in any temporary support situation in place of wood posts or steel mechanical or hydraulic supports. This includes use prior to roof bolting in room and pillar mining and in longwall development sections, use as head and tailgate supports for a longwall, and use as turn posts and breaker posts in retreat mining operations. The supports feature a release valve for quick manual extension to roof level, a lanyard

Jan 1, 1983

Reduce dust generated during bagging at minerals processing facilities, such as silica sand operations. Approach Installation of a new type of bag nozzle system eliminates the major dust sources during the bag filling process. How It Works The drawing illustrates components of the new bag nozzle system. The system differs in several ways from the conventional nozzle system. An improved bag clamp reduces the amount of blow-back during bag filling, because it has direct contact with approximately 80 per-cent of the nozzle. A two nozzle arrangement includes an inner or "fill" nozzle surrounded by another nozzle, which is designed to exhaust excess pressure from the bag after it has been filled. The exhaust is powered by an eductor, which uses a venturi effect to exhaust the bag at approximately 50 cfm. The exhaust exits into a bucket elevator and is recycled. A pinch valve automatically opens and closes the exhaust system to the bag.

Jan 1, 1984