Search Documents

By A. J. Miscoe

A unique machine for inducing bending fatigue in wire ropes was built at the U.S. Bureau of Mines' Pittsburgh Research Center. This machine can produce nine levels of degradation through repetitive cycling of long samples of wire ropes of the types used in the mining industry. This report provides an analysis of the results of the first wire rope to be fatigued on this machine. These results have indicated that as a wire rope accumulates bending cycles, its strength first decreases because of wear and then in-creases due to cold working of the wires. As the amount of cold working increases, more and more of the embrittled wires break and the strength of the rope decreases rapidly. In this test, application of several of the regulatory retirement criteria to various sections of the rope suggests that there may be some inconsistency among them.

Jan 1, 2010

By C. H. Elder, Maurice Deul

Coal degasification boreholes drilled from the surface have been success - fully hydraulically stimulated to increase the flow of gas from the coal. This Bureau of Mines report describes the hydraulic stimulation procedure for a coalbed, the equipment required, and design criteria for the treatment. Three examples of stimulation treatment show from fivefold to twentyfold increases in gas production. The tests were conducted in the Pocahontas No. 3coalbed, Buchanan County, Va., the Pittsburgh coalbed, Washington County, Pa., and the Mary Lee coalbed, Jefferson County, Ala. Two sites where the coal was hydraulically stimulated and exposed by subsequent mining show no adverse effect on mining operations through the treated zones. The induced vertical partings were confined to the coalbed and did not in any way affect either roof or floor rock.

Jan 1, 1975

By G. D. Coe

Float-and-sink tests indicate what results are obtainable by gravity separation and rare therefore an invaluable adjunct to most coal-cleaning processes. However, it is difficult to make a direct interpretation of float-and-sink data on coal, and several systems for interpreting them have been proposed. Of these, that developed and used extensively by Bird3/, Yancey4/, and Gandrud5/ is considered by the author to be the most satisfactory. It makes use of four interrelated curves (hereafter referred to as be "washability curves"). These curves were explained by Bird in a paper6/ published in 1923, but his explanation has been regarded by some as not sufficiently

Jan 1, 1938

By Terry J. Close

In 1992, as part of the U.S. Bureau of Mines Idaho Land Assessment Program, the Western Field Operations Center investigated the mineral resources of the 30,300-hectare Elk Summit study area. The area is in the Clearwater National Forest, adjoining the Selway-Bitterroot Wilderness in Idaho County. Idaho. The study area is underlain by granitic and metasedimentary rocks. Associated with these rocks are road metal (stone) resources, black sand mineral placer resources, and thermal water resources. Also present are abundant sand and gravel. Two of the five sites examined during the Bureau study have road metal (stone) resources, one has black sand mineral resources, one has thermal water resources. The fifth site is a black sand mineral placer occurrence. There is no evidence of petroleum or coal resources. Idaho County records indicate that 38 mining claims, mostly black-sand placer, have been located in the study area, Twenty-three of the claims are current. Workings consist of a few pits and trenches at the placer, and two borrow pits. The only mineral commodity produced from the area was about 1,500 tonnes of stone excavated from the Savage Pass and Swamp Creek borrow pits along the Elk Summit road, north of Hoodoo Lake. The stone was used to surface the road; these stone resources will continue to be used as needed.

Jan 1, 1993

By Nick Derick

The continued growth of steel production in the Western States is contingent upon the development of new iron ore sources. Recent development of economical techniques for concentrating and agglomerating taconites has focused attention on the low-grade magnetite deposits near Atlantic City, Wyo., as potentially important sources of iron ore for blast furnace smelting. Therefore, the Federal Bureau of Mines has made comparative evaluations of blast furnace burdens that incorporate pellets produced from Atlantic City concentrates. The Bureau also has evaluated the relative effect of Utah coke on blast furnace performance, using a high-quality Eastern coke as a basis for comparison. This work was done in the Bureau's experimental blast furnace at Bruceton, Pa. Tests determined the maximum wind rate that could be used while a continuous stock movement was maintained in the furnace. The furnace was operated at wind rates ranging from 800 to 1,400 std. c.f.m., them maximum limit of the blowers for the 1.75 in.-diameter tuyeres used. Using a normal Utah ore burden and Utah coke, the furnace went into a tight hanging condition with a wind rate above 950 std, c.f.m. Using the experimental pellet burden again with Utah coke, the wind rate could be increased to 1,000 std, c.f.m. and probably to 1,050 std. c.f.m, before tight hanging occurs. This represents an increase of 5 to 10 pct. in the wind rate. The experimental results indicate an accompanying increase of iron production, as much as 8 pct.

Jan 1, 1961

By Charles K. Rose

This paper presents some research studies of the rotary drilling of oil shale at the Bureau of Mines Oil-Shale Mine, Rifle, Colo. The experimental procedures and the rotary drill test equipment are described. Theories of rock drillability, rotary bit cutting action, and bit design are presented and discussed. The actions of various bit designs are analyzed and compared with the observed results of actual drilling tests. A cost estimate is made for drilling Colorado oil shale.

Jan 1, 1955

By Alex C. Smith, Thomas P. Mucho, John B. Walsh, Alden Ozment, Michael R. Thibou, Michael A. Trevits

The National Institute for Occupational Safety and Health (NIOSH), with US Foam Technologies, Inc. and On Site Gas Systems, Inc., conducted research on the remote application of extinguishing agents with the intent of improving deployment strategies to limit miner exposure and to help ensure the best possible outcome during a mine fire. Full-scale in-mine were conducted at the NIOSH Lake Lynn Experimental Mine to determine the flow characteristics, stability and fire-suppression capability of gas-enhanced foam. The in-mine experimental work was designed to evaluate movement of gas-enhanced foam through mine workings closely simulating an underground coal mine environment and how long gas-enhanced foam would remain stable. This paper presents results of the experiments and provides valuable insight into mine fire deployment strategies for gas-enhanced foam technology.

By Jim F. Lemons

The Bureau of Mines Minerals Availability System collected and analyzed data for 34 nonlaterite and 9 nickeliferous laterite domestic chromite deposits in order to assess their viability as sources of chromium under present technologic and economic conditions. These 43 deposits, none currently in production, contain approximately 6.3 and 22.3 million metric tons of Cr203 at the demonstrated and identified resource levels, respectively. Approximately 4.6 and 15.6 million metric tons of Cr203 are recoverable at the demonstrated and identified levels, respectively, for the 34 nonlaterite deposits. None of these resources are economically recoverable at January 1981 market prices. Production of metallurgical-grade chromite (market price $128 to $144) would require a minimum chromite market price of $237 per metric ton. Chemical-grade chromite production (market price $74 to $85) would require a chromite market price in excess of $188 per metric ton. From the 34 nonlaterite deposits, roughly 5.4 and 17.6 million metric tons of ferrochrome could be produced at the demonstrated and identified resource levels, respectively; however, a minimum market price of $770 per metric ton of ferrochrome would be required to stimulate production. The nine nickeliferous laterite deposits were not evaluated through production stages because of uncertainties in process technology and cost.

Jan 1, 1982

By E. A. Loria

High-quality sheet of electrowon molybdenum was attained by a sequence of procedure on pressed and arc-melted crystalline powders. The procedures included high-temperature, high-vacuum sintering treatments and the use of metal deoxidizers instead of carbon to improve the mechanical properties of the molybdenum sheet. Rolled sheet 60 mils thick was evaluated by tensile and bend tests, hardness measurements, microstructures, and recrystallization treatments. After stress relieving, yield strength ranged from 85,000 to 110,500 psi (0.2- percent offset) and ultimate strength ranged from 87,200 to 117,250 psi with 4.5- to 25-percent elongation observed for arc-melted sheet, and 5.0- to 23- percent elongation observed for powder metallurgy sheet. In room temperature bend tests the sheet yielded plastically, indicating that the ductile-brittle transition point was below room temperature. The diamond pyramid hardness (DPH) of the molybdenum sheet changed from 214 to 293 DPH for the stress-relieved condition to 177 to 185 DPH for the fully recrystallized condition. The brittleness of recrystallized molybdenum, reported by other investigators as characteristic of sheet prepared from commercial-grade hydrogen-reduced powders, was not in evidence. Recrystallized tensile specimens pulled at room temperature had an average elongation of 31 percent.

Jan 1, 1966

By Irving Hartmann

Following the severe starch-dust explosion in the casting department of a large candy factory nearly 2 years ago, great interest has been shown in the explosive properties and the safe manufacture and handling of powdered starches. Under the auspices of the National Fire Protection Association, a committee has been formed to prepare a code aimed at preventing dust explosions in the confectionery industry. One objective of this code will be to reduce the explosion hazards of starches that are widely used for molding, dusting, and other candy-manufacturing processes. The explosibilities of starches and starch mixtures have been studied in the laboratories of the Bureau of Mines and elsewhere. The results of the initial experiments made by the Bureau on 10 samples of cornstarch and mixtures of cornstarch with other materials have been published. In response to numerous requests for additional information, further laboratory studies have been conducted. Data have been obtained on the effects of dust concentration, particle size, moisture content, admixture of .calcium carbonate, and on the effect of oil treatment on the explosibility of cornstarch. The results of this investigation are summarized in this report.

Jan 1, 1950

By W. R. Reed

A computer model named the "Dynamic Component Program" (DCP) was specifically designed for predicting the dispersion off dust from haul trucks at surface mines. Validation of the DCP was completed by comparing its results with the results of the 1SC3 model and with actual dust measurements taken front two operating mine sires. Comparisons of the field measurements, predictions of the ISC3 model and the predictions of the DCP demonstrate that the results from the DCP represent, on average, an 85% improvement truer the ISC3 dust dispersion model results.

Jan 1, 2008

By L. L. NAUS, R. D. Currie

Hazards in connection with the use of compressed-air jets for ventilating gassy mines are given little consideration by most mine officials largely because compressed air is considered the safest means of transmitting power for operating various types of mining machinery, and the inherent dangers in its use for this purpose are virtually negligible . The installation of compressed-air lines in coal mines leads to the utilization of compressed air for ventilating working places , with the result that , although the primary ventilation systems may be adequate to meet existing needs , proper conduction of normal ventilation has been neglected , so the working faces receive only a small amount ofthe total air circulated through the mine . Reliance in part on compressed air or other auxiliary means for ventilation is always attended by danger that gas will accumulate , due to intermittent operation , and the tendency is to operate auxiliary schemes only. during the working shift ( or possibly only part of the shift ) and to dispense with them during off- shifts or at times during the working shift when gas may accumulate because of lack of ventilation . When the men come on shift the auxiliary ventilating device often may be started without a preliminary examination of the working place , or .. the examination may be made sometime before the oncoming shift arrives , the gas being allowed to accumulate in the meantime. This may result in uncontrolled movement of a body of gas if proper precautions are not taken . Several mine explosions have been caused by the movement of a known body of gas by compressed air into the haulageway, where it was ignited by an arc from a passing locomotive . This danger is more pronounced where supervision is lax .

Aug 1, 1937

By John J. McClelland

The Bureau of Mines conducted a study of longwall plow operations to identify dust sources and existing control technology. Three longwalls employing either the high-speed overtaking or conventional method of mining were surveyed. Principal operating parameters and on-site dust control technology at the time of each survey are described. Short-term gravimetric and instantaneous sampling results are discussed in detail. The relationship between longwall dust levels and dust control technology was examined.

Jan 1, 1988

By A. J. Keast

This circular is one of a series dealing with the exploration, equipping, and development of mining properties, prepared and published by the United States Bureau of Mines in cooperation with various mining and exploration companies in the United States and Canada. This series of papers will supplement an earlier one which covered the methods and costs of mining and milling at a large number of producing mines. The present paper describes the exploration, equipping, and developing of a group of 18 claims remote from rail transportation, and the transport of equipment and heavy supplies for a distance of 120 miles by tractor over ice and winter roads, and of men and lighter supplies by airplane.

Jan 1, 1933

By N. S. Dalal, X. Shi, V. Vallyathan

"INTRODUCTIONThis paper summarizes our recent investigations of the potential role of silicon-oxygen based free radical species in the biochemical mechanism of the lung injury caused by the inhalation of freshly fractured silica. The impetus for this study came from the following observations. Inhalation of crystalline silica is associated with the development of acute and chronic silicosis. Chronic silicosis is characterized by the development of sharply marked concentric fibrotic nodules in the lung. This occurs over a period of several decades with the development of progressive respiratory impairment. In contrast, acute silicosis is manifested by the filling of the alveoli with an amorphous lipoproteinaceous exudate within a short period after exposure, and rapid development of respiratory disability often leading to fatality. Most studies on the pathogenesis of silicosis have focused on the elucidation of cellular mechanisms of cell injury and the development of chronic silicosis. Because pulmonary responses to crystalline silica are distinctly different for · the acute and chronic silicosis, we hypothesized that the acute response is associated with some unique properties of ·freshly formed silica particle surfaces, due to the formation of some reactive chemical species caused by the rupturing or the silicon-oxygen bonds. In occupations involving drilling, tunneling and sandblasting operations acute silicosis can be correlated with this unique surface reactivity of silica. The formation or reactive species was demonstrated, using electron spin resonance (ESR) spectroscopy (Dalal et al., 1986; Fuibini et al., 1987; Hochstrasser and Antononi, 1972). Grinding of quartz crystals under ultra high vacuum (10-10 torr) leads to the formation of Si- and SiO• radicals and these radicals are quenched by exposure to air and other gases (Hochstrasser and Antonini, 1972). ESR signals have also been reported from micronized quartz samples that were evacuated at 413 K (Bolls et al., 1983). In order to find a more direct relationship of such radicals to acute silicosis, we made ESR measurements on quartz dusts freshly ground in ambient air and found- that indeed grinding under ambient environment leads to the formation of the Si• and SiO• type of radicals which decay on storing the dusts in air or in biological buffers (Dalai et al., 1986; Vallyathan et al., 1988). The Si• and SiO radical formation on grinding has also been reported by Fubini et al. (1987). In addition, we recently found that •OH radicals are generated in aqueous suspensions of freshly ground quartz (Dalai et al., 1988; Shi et al., 1988; Vallyathan et al., 1988). We have subsequently carried out detailed cytotoxicity and biological assays on freshly made as well as aged quartz dusts. As summarized below, the results provide new insight into the biochemical mechanism of acute silicosis."

Jan 1, 1988

By Perry G. Cotter

As a portion of a general program for the synthesis of hard materials, a method was sought by which the hardness and density of tungsten carbide (WC)-cobalt compacts could be increased. It was demonstrated by Cotter that these improvements in quality could be made by employing an electric-resistance sintering process in which heat and pressure are applied simultaneously to presintered compacts composed of powdered tungsten carbide and cobalt. This conclusion was based on tests of material prepared by Cotter on welding equipment in use at the U. S. Naval Engineering Experiment Station, Annapolis, Md., and at Rensselaer Polytechnic Institute, Troy, N. Y. Rockwell-hardness tests made at Norris and core-drilling tests made at the Mount Weather Station of the Bureau of Mines indicated that, for some purposes, carbide material made by this process might be superior to the chemically analogous commercial products prepared by ordinary sintering methods. A program to develop optimum conditions for the electric-resistance sintering of tungsten carbide-cobalt compacts was initiated. The program was followed by a systematic evaluation of the hardness and density of compacts prepared by this method along with a series of carbide compacts furnished by various manufacturers. This paper presents a description of the electric-resistance sintering of tungsten carbide-cobalt compacts and the results of comparative physical tests.

Jan 1, 1955

By W. N. Cathey

Many materials including carbides, silicides, phosphides, borides, nitrides, oxides, and metals were studied by the Bureau of Mines as potential fuel cell catalysts for electroreduction of oxygen in a 1[N]H2S04 electrolyte. The objective of this study was to assess the potential of abundant, low-cost materials as substitutes for platinum or to increase the catalytic efficiency of platinum. Several compounds were rejected because of their reaction in the corrosive environment of the oxygen electrode. However, some of the remaining were the most active catalysts. Activity of carbides such as tungsten carbide could be improved by doping with platinum-group metals, by varying stoichiometry, or by sputtering on a layer of platinum. While no catalysts were found with activity as high as platinum, some compounds were shown to be deserving of further investigation.

Jan 1, 1979

By S. M. Molloy

The postwar demand for insulating material such as mineral wool, in-creased in proportion to the rapid construction of new buildings, placing an enormous burden on the existing mineral-wool industry both in known sources of raw materials and in available plant facilities. In view of the increased demand on the industry, the Bureau of Mines in its Mississippi Valley Experiment Station" Rolla, Mo., undertook an investigation to aid the industry by establishing resources of raw materials through actual laboratory wool-blowing tests and by developing certain methods for evaluating the physical proper-ties of a mineral wool. As material was received from the public, laboratory-evaluation technique had to be developed, the results of which would reflect in the mineral-wool-industry standards. The methods of testing used by the mineral-wool industry, not only would have required a pilot-plant installation capable of producing a large tonnage of mineral wool, but each wool-blowing campaign would have been very expensive and necessitated considerable personnel and equipment. The present laboratory wool-blowing equipment can produce as high as eight wool-blowing campaigns a day. The nature, simplicity, and size of the physical testing equipment permit testing as small a sample of wool as 25 grams and give information as reasonably accurate as in a 40-pound bag of wool. The purpose of this report is to describe the laboratory method of production and the evaluation of the physical properties of small quantities of mineral wool. Considerable work has already been done, and the interest of the public and industry is measured in the number of samples being submitted for testing.

Jan 1, 1948

By David M. Hyman

The Bureau of Mines has developed two experimental designs for deter- mining the volumes and relative proportions of the various gas species, particularly methane (CH4), occluded in rock salt. To date, the rock salt samples analyzed have been relatively small (400- to 1,000-gram) grab samples from Louisiana Gulf Coast domal salt mines. The results obtained are comparable to results in Polish domal salt mines, in terms of occluded gas volumes per mass of rock salt. The notable difference between the Louisiana and Polish occluded gas mixtures is in the relative proportions of the individual gas species. The two methods used by the Bureau are ballmill crushing and dissolution. Of the two, the dissolution method appears to be more versatile because it can be performed in situ. The relevance and applicability of data on the occluded gas contents of rock salt are dependent on sample size, sample collection method, geologic context of the sample, and the correlation with gas emissions that occur as a result of mining-induced fractures and pressure differentials.

Jan 1, 1982

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

MINE VENTILATION NETWORK ANALYSIS

Jan 1, 1977